TJ7BTK-729Bluetooth Headset

Bluetooth ® headset users Manual BTK-729 1 Thank you for purchasing the Just Wireless Bluetooth® Headset. We hope you enjoy it. This manual will get you started and help you to get familiar with the features of your headset. For those individuals with the Bluetooth® Headset, in addition to all the other features, the unit supports a multipoint func- tion to allow simultaneous connection of the Bluetooth® Headset with 2 mobile phones. About your Just Wireless bluetooth heAdset Your Just Wireless® Bluetooth® Headset lets you do the following functions, provided your mobile phone can support it: • Making a call • Ending a call • Answering calls • Adjusting Volume • Voice Command Dialing • Redialing last number • Placing a call on hold • Call Waiting • Rejecting a call inTRoDuCTion Before you Begin to use your Just Wireless ® Bluetooth ® headset, you must fully charge and pair it With your moBile phone. please read the enclosed users manual for easy pairing instructions. should you need assistance, please call 888-753-6957. STOP AND READ 23 FEATuRE DiAgRAM 1 LED indicator Light a) Blue mode indicates active/standby. • 1 Flash every 5 seconds: Your Bluetooth® Headset is not connected to your mobile phone. • 1 Flash every 7 seconds: Your Bluetooth® Headset is connected to your mobile phone. b) Red mode indicates battery level. • Flashing Red - indicates low battery level. • Solid Red - indicates your Bluetooth® Headset is being charged. • Solid Blue - The battery is fully charged. c) Blue/Red Flashing Mode • Your Bluetooth® Headset is in pairing mode Main Button Volume Higher/Lower 4 Charging Port 5 Microphone 6 6 Adjustable Ear Hook 6 Earphone 2 2 3 5 6 Adjustable Ear Hook Main Button Microphone 4 Charging Port 3 Volume Higher/Lower 7 Earphone 1 LED indicator 7 45 ChArging your heAdset Your Just Wireless® Bluetooth® Headset comes with a built in rechargeable battery, and must be fully charged before using. use the supplied uSB Cable to charge your headset by plugging it into the charging jack shown below. • The red LED light will flash when you have a low battery level. it is suggested to charge the headset at this time. • The red light will illuminate solid red during charging and will turn solid blue when fully charged. it will take approximately 1-2 hours to charge. • Your headset cannot be used while charging. turning the heAdset on And oFF on mode: Press and hold down the Main Button for 3 seconds. Your headset will beep and the blue LED light will flash 4 times. now your headset is on. off mode: Press and hold down the Main Button for 4 seconds. You headset will beep and the red LED light will flash 2 times. now your headset is off. standby mode: To save battery power, your headset will automatically change to standby mode when not in use. The blue LED light will flash every 7 seconds. The headset will automatically change back to on mode, when a call is incoming, or when the Main Button is pressed. gETTing STARTED 67 PAiring And ConneCting your heAdset to your mobile Phone Pairing is a process of linking the Bluetooth® Headset with your mobile phone. Before using your Bluetooth® Headset, you must successfully pair it to your mobile phone. Your mobile phone must be Bluetooth® compatible. if it is not, you will not be able to pair the headset to your mobile phone. Check the users manual of your mobile phone to see if it is Bluetooth® compatible. Your mobile phone and headset should not be more than 3 feet in distance when pairing. step 1 - setting the headset into pairing mode: in the oFF mode, press and hold down the Main Button for 9 seconds, until you see the LED light consecutively flashing blue and red. Your Bluetooth® Headset is now in pairing mode. step 2 - setting the mobile phone into pairing or “discover” mode: Follow your mobile phone’s instruction manual. Although it is different on all types of mobile phone brands and models, it usually involves going to the “set up”, “connect” or “Bluetooth®” menu on your mobile phone, and selecting the option “discover” or “add” a Bluetooth® device. step 3 - completing the pairing: Your mobile phone will search for your Bluetooth® Headset. The LED indicator light must continue to consecutively flash blue and red while your mobile phone is searching for your Bluetooth® Headset. if it isn’t flashing blue/red repeat step 1 above. When your mobile phone finds Bluetooth® Headset, you will need to accept your Bluetooth® Headset by pressing “Pair”, “Yes” or “oK” on your mobile phone and then confirm using the passkey or pin number 0000. The headset and mobile phone are now paired and the LED light on the headset will now flash blue 2 times consecutively. You will only have to pair your Bluetooth® Headset to your mobile phone once. After this process has been completed you can use the Bluetooth® Headset only with its paired mobile phone. Repeat steps 1-3 if pairing was unsuccessful. 89 step 4 - connecting: Most phones require an additional step to “connect” to a Bluetooth® Headset. Follow the instructions in your mobile phone users manual. once connected, your Bluetooth® Headset LED light will flash 1 time every 5 seconds. if either the Bluetooth® Headset unit or your mobile phone is turned off, most mobile phones will allow you to automatically connect back to your Bluetooth® Headset once your headset or mobille phone is turned back on. However with some mobile phones, you will need to manually reconnect. Your mobile phone’s users manual will guide you through these set up instructions. step 5 - pairing and connecting to a second phone: For those individuals with the Bluetooth® Headset, it supports a multipoint function to allow simultaneous connection of the headset with 2 mobile phones. once you have paired and connected your Bluetooth® Headset to the 1st mobile phone, as per the instructions above in steps 1-4, to pair and connect your Bluetooth® Headset to a second phone, place your Bluetooth® Headset in the off mode and repeat the instructio…

Text truncated - open the document above for the full version.

RV-0000000 Project No.: 1406C153 Page 2 of 8

RV-0000000 Project No.: 1406C153 Page 3 of 8 RV-0000000 Project No.: 1406C153 Page 4 of 8 RV-0000000 Project No.: 1406C153 Page 5 of 8 Main Board RV-0000000 Project No.: 1406C153 Page 6 of 8 RF Module IC Crystal RV-0000000 Project No.: 1406C153 Page 7 of 8 Chip antenna RV-0000000 Project No.: 1406C153 Page 8 of 8

Report No.: NEI-FCCP-1-1406C174 Page 1 of 108 FCC Radio Test Report FCC ID: TJ7BTK-729 This report concerns (check one): Original Grant Class II Change Project No. : 1406C174 Equipment : Bluetooth Headset Model Name : BTK-729;BT-40;BTK-730;BTK-731; BTK-732;BTK-733;BTK-734;BTK-735; BTK-736;BTK-737;BTK-738;BTK-739; BTK-740;BTK-741;BTK-742;BTK-743; BTK-744;BTK-745;BTK-746;BTK-747; BTK-748;BTK-750 Applicant : ShenZhen SHI KISB Electronic Co., LTD Address : 3-5F, A Building, Shanghe Industrial Zone, Nanchang Road, Gushu Village, Xixiang Town, Bao’an District, Shenzhen, Guangdong, China Tested by: BTL Inc. EMC Laboratory Date of Receipt: Jun. 20, 2014 Date of Test: Jun. 20, 2014~ Jul. 01, 2014 Issued Date: Jul. 02, 2014 Testing Engineer : (David Mao) Technical Manager : (Leo Hung) Authorized Signatory : (Steven Lu) BTL INC. No.3, Jinshagang 1st Road, Shixia, Dalang Town, Dongguan, China. TEL: 0769-8318-3000 FAX: 0769-8319-6000 Report No.: NEI-FCCP-1-1406C174 Page 2 of 108 Declaration BTL represents to the client that testing is done in accordance with standard procedures as applicable and that test instruments used has been calibrated with the standards traceable to National Measurement Laboratory (NML) of CHINA, or National Institute of Standards and Technology (NIST) of U.S.A. BTL's reports apply only to the specific samples tested under conditions. It is manufacture’s responsibility to ensure that additional production units of this model are manufactured with the identical electrical and mechanical components. BTL shall have no liability for any declarations, inferences or generalizations drawn by the client or others from BTL issued reports. BTL’s reports must not be used by the client to claim product endorsement by the authorities or any agency of the Government. This report is the confidential property of the client. As a mutual protection to the clients, the public and BTL-self, extracts from the test report shall not be reproduced except in full with BTL’s authorized written approval. BTL’s laboratory quality assurance procedures are in compliance with the ISO Guide 17025 requirements, and accredited by the conformity assessment authorities listed in this test report. Limitation For the use of the authority's logo is limited unless the Test Standard(s)/Scope(s)/Item(s) mentioned in this test report is (are) included in the conformity assessment authorities acceptance respective. Report No.: NEI-FCCP-1-1406C174 Page 3 of 108 Table of Contents Page 1 . CERTIFICATION 7 2 . SUMMARY OF TEST RESULTS 8 2.1 TEST FACILITY 9 2.2 MEASUREMENT UNCERTAINTY 9 3 . GENERAL INFORMATION 10 3.1 GENERAL DESCRIPTION OF EUT 10 3.2 DESCRIPTION OF TEST MODES 12 3.3 TABLE OF PARAMETERS OF TEXT SOFTWARE SETTING 12 3.4 BLOCK DIAGRAM SHOWING THE CONFIGURATION OF SYSTEM TESTED 13 3.5 DESCRIPTION OF SUPPORT UNITS 14 4 . EMC EMISSION TEST 15 4.1 CONDUCTED EMISSION MEASUREMENT 15 4.1.1 POWER LINE CONDUCTED EMISSION LIMITS 15 4.1.2 TEST PROCEDURE 15 4.1.3 DEVIATION FROM TEST STANDARD 15 4.1.4 TEST SETUP 16 4.1.5 EUT OPERATING CONDITIONS 16 4.1.6 EUT TEST CONDITIONS 16 4.1.7 TEST RESULTS 16 4.2 RADIATED EMISSION MEASUREMENT 17 4.2.1 RADIATED EMISSION LIMITS 17 4.2.2 TEST PROCEDURE 18 4.2.3 DEVIATION FROM TEST STANDARD 18 4.2.4 TEST SETUP 19 4.2.5 EUT OPERATING CONDITIONS 20 4.2.6 EUT TEST CONDITIONS 20 4.2.7 TEST RESULTS (9KHZ TO 30MHZ) 20 4.2.8 TEST RESULTS (BETWEEN 30MHZ TO 1000 MHZ) 21 4.2.9 TEST RESULTS (ABOVE 1000 MHZ) 21 5 . NUMBER OF HOPPING CHANNEL 22 5.1 APPLIED PROCEDURES 22 5.1.1 TEST PROCEDURE 22 5.1.2 DEVIATION FROM STANDARD 22 5.1.3 TEST SETUP 22 5.1.4 EUT OPERATION CONDITIONS 22 5.1.5 EUT TEST CONDITIONS 22 5.1.6 TEST RESULTS 22 Report No.: NEI-FCCP-1-1406C174 Page 4 of 108 Table of Contents Page 6 . AVERAGE TIME OF OCCUPANCY 23 6.1 APPLIED PROCEDURES / LIMIT 23 6.1.1 TEST PROCEDURE 23 6.1.2 DEVIATION FROM STANDARD 23 6.1.3 TEST SETUP 23 6.1.4 EUT OPERATION CONDITIONS 24 6.1.5 EUT TEST CONDITIONS 24 6.1.6 TEST RESULTS 24 7 . HOPPING CHANNEL SEPARATION MEASUREMENT 25 7.1 APPLIED PROCEDURES / LIMIT 25 7.1.1 TEST PROCEDURE 25 7.1.2 DEVIATION FROM STANDARD 25 7.1.3 TEST SETUP 25 7.1.4 EUT TEST CONDITIONS 25 7.1.5 TEST RESULTS 25 8 . BANDWIDTH TEST 26 8.1 APPLIED PROCEDURES 26 8.1.1 TEST PROCEDURE 26 8.1.2 DEVIATION FROM STANDARD 26 8.1.3 TEST SETUP 26 8.1.4 EUT OPERATION CONDITIONS 26 8.1.5 EUT TEST CONDITIONS 26 8.1.6 TEST RESULTS 26 9 . PEAK OUTPUT POWER TEST 27 9.1 APPLIED PROCEDURES / LIMIT 27 9.1.1 TEST PROCEDURE 27 9.1.2 DEVIATION FROM STANDARD 27 9.1.3 TEST SETUP 27 9.1.4 EUT OPERATION CONDITIONS 27 9.1.5 EUT TEST CONDITIONS 27 9.1.6 TEST RESULTS 27 10 . ANTENNA CONDUCTED SPURIOUS EMISSION 28 10.1 APPLIED PROCEDURES / LIMIT 28 10.1.1 TEST PROCEDURE 28 10.1.2 DEVIATION FROM STANDARD 28 10.1.3 TEST SETUP 28 10.1.4 EUT OPERATION CONDITIONS 28 10.1.5 EUT TEST CONDITIONS 28 10.1.6 TEST RESULTS 28 Report No.: NEI-FCCP-1-1406C174 Page 5 of 108 Table of Contents Page 11 . MEASUREMENT INSTRUMENTS LIST 29 12 . EUT TEST PHOTO 31 ATTACHMENT A - CONDUCTED EMISSION 35 ATTACHMENT B - RADIATED EMISSION (9KHZ-30MHZ) 38 ATTACHMENT C - RADIATED EMISSION (30MHZ TO 1000MHZ) 40 ATTACHMENT D - RADIATED EMISSION (ABOVE 1000MHZ) 47 ATTACHMENT E - NUMBER OF HOPPING CHANNEL 72 ATTACHMENT F - AVERAGE TIME OF OCCUPANCY 74 ATTACHMENT G - HOPPING CHANNEL SEPARATION MEASUREMENT 87 ATTACHMENT H - BANDWIDTH 92 ATTACHMENT I - PEAK OUTPUT POWER 97 ATTACHMENT J - ANTENNA CONDUCTED SPURIOUS EMISSION 102 Report No.: NEI-FCCP-1-1406C174 Page 6 of 108 REPORT ISSUED HISTORY Issued No. Description Issued Date NEI-FCCP-1-1406C174 Original Issue. Jul. 02, 2014 Report No.: NEI-FCCP-1-1406C174 Page 7 of 108 1. CERTIFICATION Equipment : Bluetooth Headset Brand Name : BTK; KISS; Lindero Model Name : BTK-729;BT-40;BTK-730;BTK-731;BTK-732;BTK-733;BTK-734;BTK-735;BTK -736;BTK-737;BTK-738;BTK-739;BTK-740;BTK-741;BTK-742;BTK-743;BTK-7 44;BTK-745;BTK-746;BTK-747;BTK-748;BTK-750 Applicant ShenZhen SHI KISB Electronic Co., LTD Manufacturer : ShenZhen SHI K…

Text truncated - open the document above for the full version.

Report No.: NEI-FCCP-1-1406C174 Page 51 of 108 Orthogonal Axis : X Test Mode : TX 2402MHz _CH00_1Mbps Horizontal Report No.: NEI-FCCP-1-1406C174 Page 52 of 108 Orthogonal Axis : X Test Mode : TX 2441MHz _CH39_1Mbps Vertical Report No.: NEI-FCCP-1-1406C174 Page 53 of 108 Orthogonal Axis : X Test Mode : TX 2441MHz _CH39_1Mbps Vertical Report No.: NEI-FCCP-1-1406C174 Page 54 of 108 Orthogonal Axis : X Test Mode : TX 2441MHz _CH39_1Mbps Horizontal Report No.: NEI-FCCP-1-1406C174 Page 55 of 108 Orthogonal Axis : X Test Mode : TX 2441MHz _CH39_1Mbps Horizontal Report No.: NEI-FCCP-1-1406C174 Page 56 of 108 Orthogonal Axis : X Test Mode : TX 2480MHz _CH78_1Mbps Vertical Report No.: NEI-FCCP-1-1406C174 Page 57 of 108 Orthogonal Axis : X Test Mode : TX 2480MHz _CH78_1Mbps Vertical Report No.: NEI-FCCP-1-1406C174 Page 58 of 108 Orthogonal Axis : X Test Mode : TX 2480MHz _CH78_1Mbps Horizontal Report No.: NEI-FCCP-1-1406C174 Page 59 of 108 Orthogonal Axis : X Test Mode : TX 2480MHz _CH78_1Mbps Horizontal Report No.: NEI-FCCP-1-1406C174 Page 60 of 108 Orthogonal Axis : X Test Mode : TX 2402MHz _CH00_3Mbps Vertical Report No.: NEI-FCCP-1-1406C174 Page 61 of 108 Orthogonal Axis : X Test Mode : TX 2402MHz _CH00_3Mbps Vertical Report No.: NEI-FCCP-1-1406C174 Page 62 of 108 Orthogonal Axis : X Test Mode : TX 2402MHz _CH00_3Mbps Horizontal

Report No.: NEI-FCCP-1-1406C174 Page 63 of 108 Orthogonal Axis : X Test Mode : TX 2402MHz _CH00_3Mbps Horizontal Report No.: NEI-FCCP-1-1406C174 Page 64 of 108 Orthogonal Axis : X Test Mode : TX 2441MHz _CH39_3Mbps Vertical Report No.: NEI-FCCP-1-1406C174 Page 65 of 108 Orthogonal Axis : X Test Mode : TX 2441MHz _CH39_3Mbps Vertical Report No.: NEI-FCCP-1-1406C174 Page 66 of 108 Orthogonal Axis : X Test Mode : TX 2441MHz _CH39_3Mbps Horizontal Report No.: NEI-FCCP-1-1406C174 Page 67 of 108 Orthogonal Axis : X Test Mode : TX 2441MHz _CH39_3Mbps Horizontal Report No.: NEI-FCCP-1-1406C174 Page 68 of 108 Orthogonal Axis : X Test Mode : TX 2480MHz _CH78_3Mbps Vertical Report No.: NEI-FCCP-1-1406C174 Page 69 of 108 Orthogonal Axis : X Test Mode : TX 2480MHz _CH78_3Mbps Vertical Report No.: NEI-FCCP-1-1406C174 Page 70 of 108 Orthogonal Axis : X Test Mode : TX 2480MHz _CH78_3Mbps Horizontal Report No.: NEI-FCCP-1-1406C174 Page 71 of 108 Orthogonal Axis : X Test Mode : TX 2480MHz _CH78_3Mbps Horizontal Report No.: NEI-FCCP-1-1406C174 Page 72 of 108 ATTACHMENT E - NUMBER OF HOPPING CHANNEL Report No.: NEI-FCCP-1-1406C174 Page 73 of 108 Test Mode Hopping Mode_1Mbps Number of Hopping Channel 79 Test Mode Hopping Mode_3Mbps Number of Hopping Channel 79 Report No.: NEI-FCCP-1-1406C174 Page 74 of 108 ATTACHMENT F - AVERAGE TIME OF OCCUPANCY Report No.: NEI-FCCP-1-1406C174 Page 75 of 108 Test Mode : TX Mode_1Mbps DH52402 MHz3.16000.33710.4000Complies DH32402 MHz1.82000.29120.4000Complies DH12402 MHz0.53500.17120.4000Complies DH52441 MHz3.28000.34990.4000Complies DH32441 MHz1.86000.29760.4000Complies DH12441 MHz0.54000.17280.4000Complies DH52480 MHz3.16000.33710.4000Complies DH32480 MHz1.88000.30080.4000Complies DH12480 MHz0.55500.17760.4000Complies Data PacketFrequencyTest Result Pulse Duration(ms) Dwell Time(s)Limits(s) Report No.: NEI-FCCP-1-1406C174 Page 76 of 108 CH00-DH1 CH00-DH3 Report No.: NEI-FCCP-1-1406C174 Page 77 of 108 CH00-DH5 CH39-DH1 Report No.: NEI-FCCP-1-1406C174 Page 78 of 108 CH39-DH3 CH39-DH5 Report No.: NEI-FCCP-1-1406C174 Page 79 of 108 CH78-DH1 CH78-DH3 Report No.: NEI-FCCP-1-1406C174 Page 80 of 108 CH78-DH5 Report No.: NEI-FCCP-1-1406C174 Page 81 of 108 Test Mode : TX Mode_3Mbps DH52402 MHz3.12000.33280.4000Complies DH32402 MHz1.86000.29760.4000Complies DH12402 MHz0.57500.18400.4000Complies DH52441 MHz3.12000.33280.4000Complies DH32441 MHz1.88000.30080.4000Complies DH12441 MHz0.57000.18240.4000Complies DH52480 MHz3.20000.34130.4000Complies DH32480 MHz1.88000.30080.4000Complies DH12480 MHz0.55500.17760.4000Complies Data PacketFrequencyTest Result Pulse Duration(ms) Dwell Time(s)Limits(s) Report No.: NEI-FCCP-1-1406C174 Page 82 of 108 CH00-DH1 CH00-DH3 Report No.: NEI-FCCP-1-1406C174 Page 83 of 108 CH00-DH5 CH39-DH1 Report No.: NEI-FCCP-1-1406C174 Page 84 of 108 CH39-DH3 CH39-DH5 Report No.: NEI-FCCP-1-1406C174 Page 85 of 108 CH78-DH1 CH78-DH3 Report No.: NEI-FCCP-1-1406C174 Page 86 of 108 CH78-DH5 Report No.: NEI-FCCP-1-1406C174 Page 87 of 108 ATTACHMENT G - HOPPING CHANNEL SEPARATION MEASUREMENT Report No.: NEI-FCCP-1-1406C174 Page 88 of 108 Test Mode : Hopping on _1Mbps 2402 MHz1.0080.565Complies 2441 MHz0.9990.558Complies 2480 MHz0.9960.562Complies 2/3 of 20dB Bandwidth(MHz) Test Result Channel Separation(MHz) Frequency CH00 Report No.: NEI-FCCP-1-1406C174 Page 89 of 108 CH39 CH78 Report No.: NEI-FCCP-1-1406C174 Page 90 of 108 Test Mode : Hopping on _3Mbps 2402 MHz0.9990.805Complies 2441 MHz1.0050.805Complies 2480 MHz1.0040.801Complies Channel Separation(MHz) Frequency 2/3 of 20dB Bandwidth(MHz) Test Result CH00 Report No.: NEI-FCCP-1-1406C174 Page 91 of 108 CH39 CH78 Report No.: NEI-FCCP-1-1406C174 Page 92 of 108 ATTACHMENT H - BANDWIDTH Report No.: NEI-FCCP-1-1406C174 Page 93 of 108 Test Mode : TX Mode _1Mbps 2402 MHz0.8480.830Complies 2441 MHz0.8370.825Complies 2480 MHz0.8430.830Complies 20dB Bandwidth(MHz) 99% Occupied BW(MHz) FrequencyTest Result CH00 Report No.: NEI-FCCP-1-1406C174 Page 94 of 108 CH39 CH78 Report No.: NEI-FCCP-1-1406C174 Page 95 of 108 Test Mode : TX Mode _3Mbps 2402 MHz1.2071.155Complies 2441 MHz1.2071.150Complies 2480 MHz1.2021.150Complies 20dB Bandwidth(MHz) 99% Occupied BW(MHz) FrequencyTest Result CH00 Report No.: NEI-FCCP-1-1406C174 Page 96 of 108 CH39 CH78 Report No.: NEI-FCCP-1-1406C174 Page 97 of 108 ATTACHMENT I - PEAK OUTPUT POWER Report No.: NEI-FCCP-1-1406C174 Page 98 of 108 Test Mode : TX Mode _1Mbps Frequency Conducted Power (dBm) Conducted Power (W) Max. Limit(dBm) Max. Limit(W) Test Result 2402 MHz3.760.002421.000.1259Complies 2441 MHz3.430.002221.000.1259Complies 2480 MHz3.110.002021.000.1259Complies CH00 Report No.: NEI-FCCP-1-1406C174 Page 99 of 108 CH39 CH78 Report No.: NEI-FCCP-1-1406C174 Page 100 of 108 Test Mode : TX Mode _3Mbps Frequency Conducted Power (dBm) Conducted Power (W) Max. Limit(dBm) Max. Limit(W) Test Result 2402 MHz3.880.002421.000.1259Complies 2441 MHz3.810.002421.000.1259Complies 2480 MHz3.840.002421.000.1259Complies CH00 Report No.: NEI-FCCP-1-1406C174 Page 101 of 108 CH39 CH78 Report No.: NEI-FCCP-1-1406C174 Page 102 of 108 ATTACHMENT J - ANTENNA CONDUCTED SPURIOUS EMISSION Report No.: NEI-FCCP-1-1406C174 Page 103 of 108 CH00 (Lower)_1Mbps CH78 (Upper) _1Mbps Report No.: NEI-FCCP-1-1406C174 Page 104 of 108 CH00 (10 Harmonic of the frequency) _1Mbps CH39 (10 Harmonic of the frequency) _1Mbps Report No.: NEI-FCCP-1-1406C174 Page 105 of 108 CH78 (10 Harmonic of the frequency) _1Mbps Report No.: NEI-FCCP-1-1406C174 Page 106 of 108 CH00 (Lower) _3Mbps CH78 (Upper) _3Mbps Report No.: NEI-FCCP-1-1406C174 Page 107 of 108 CH00 (10 Harmonic of the frequency) _3Mbps CH39 (10 Harmonic of the frequency) _3Mbps Report No.: NEI-FCCP-1-1406C174 Page 108 of 108 CH78 (10 Harmonic of the frequency) _3Mbps

Report No.: NEI-FCCP-1-1406C174 Page 31 of 10 8 12. EUT TEST PHOTO Conducted Measurement Photos Report No.: NEI-FCCP-1-1406C174 Page 32 of 10 8 Radiated Measurement Photos 9KHz to 30MHz Report No.: NEI-FCCP-1-1406C174 Page 33 of 10 8 Radiated Measurement Photos 30MHz to 1000MHz Report No.: NEI-FCCP-1-1406C174 Page 34 of 10 8 Radiated Measurement Photos Above 1000MHz