TNU-EQN2201-WIP Camera

EQN2200 User’s Manual Copyright © EverFocus Electronics Corp, Release: Mar. 2010 EQN2200 2 Product Name: EQN2200 EverFocus Network Cameras Model Number(s): EQN2200 Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter. For product available in the USA/Canada market, only channel 1~11 can be operated. Selection of other channels is not possible. IMPORTANT NOTE: FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. EQN2200 3 EverFocus Electronics Corp. 12F, No. 79, Sec. 1, Shin-Tai Wu Rd., His-Chi, Taipei Hsien, Taiwan, R.O.C. EQN2200 complies with CE and FCC rules. EQN2200 4 About this document All the safety and operating instructions should be read and followed before the unit is operated. This manual should be retained for future reference. The information in this manual was current when published. The manufacturer reserves the right to revise and improve its products. All specifications are therefore subject to change without notice. Safety Notices -These limits are designed to provide reasonable protection against interference. This equipment may generate, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -Reorient or relocate the receiving antenna. -Increase these separations between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help. Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. To reduce risk of fire or electric shock, do not expose this camera to rain or moisture. Do not attempt to disassemble the camera. To prevent electric shock, do not remove screws or covers. There are no user-serviceable parts inside. Contact qualified service personnel for maintenance. Handle the camera with care. Do not strike or shake, as this may damage the camera. Do not use strong or abrasive detergents when cleaning the camera body. Use a dry cloth to clean the camera when it is dirty. When the dirt is hard to remove, EQN2200 5 use a mild detergent and wipe gently. Do not operate the camera beyond its specified temperature, humidity or power source ratings. Do not use the camera in an extreme environment where high temperature or high humidity exists. Use the camera at temperature within 0°C ~ +40°C / 32۫F~ 104۫F and a humidity below 90%. The input power source for this camera is 12 VDC & 802.3af PoE. Use only the recommended power supplies. Power supplies must comply with the requirement of the latest version of IEC60950-1. Substitutions may damage the unit or cause a fire or shock hazard. Electrostatic-sensitive device. Use proper CMOS/MOSFET handing precautions to avoid electrostatic discharge. Installation should be performed by qualified service personnel only in accordance with the National Electrical Code or applicable local codes. Terms and Trademark Ethernet, Internet Explorer, Linux, Microsoft, Windows, WWW are registered trademarks of the respective holders. Other product names appearing in this User's Guide may be trademarks or registered trademarks of their respective holders. Java™ and all Java-related logos and trademarks are trademarks or registered trademarks of Sun Microsystems, Inc. in the United States and other countries. Support If the unit ever needs repair service, the customer should contact the nearest EverFocus Electronics Corp. Service Center for return authorization and shipping instruction. About this AC Adaptor Specifications for AC adaptor Power Supply: 12VDC, 1 A Power Output: 12VDC, 1 A Operating Temperature: 0°C ~ 40°C / 32۫F ~ 104۫F External Dimensions: 56 mm x 68 mm x 101 mm / 2.24” x 2.72” x 4.04” EQN2200 6 TABLE OF CONTENTS 1. INTRODUCTION....................................................................................................7 2. FEATURES ..............................................................................................................7 3. SPECIFICATIONS ..................................................................................................8 4…

Text truncated - open the document above for the full version.

FCC TEST REPORT SPORTON International Inc. PAGE NUMBER : C1 OF C12 TEL : 886-2-2696-2468 ISSUED DATE : Mar. 10, 2010 FAX : 886-2-2696-2255 APPENDIX C. Photographs of EUT FCC TEST REPORT SPORTON International Inc. PAGE NUMBER : C2 OF C12 TEL : 886-2-2696-2468 ISSUED DATE : Mar. 10, 2010 FAX : 886-2-2696-2255 FCC TEST REPORT SPORTON International Inc. PAGE NUMBER : C11 OF C12 TEL : 886-2-2696-2468 ISSUED DATE : Mar. 10, 2010 FAX : 886-2-2696-2255 FCC TEST REPORT SPORTON International Inc. PAGE NUMBER : C12 OF C12 TEL : 886-2-2696-2468 ISSUED DATE : Mar. 10, 2010 FAX : 886-2-2696-2255

FCC TEST REPORT SPORTON International Inc. PAGE NUMBER : C3 OF C12 TEL : 886-2-2696-2468 ISSUED DATE : Mar. 10, 2010 FAX : 886-2-2696-2255 FCC TEST REPORT SPORTON International Inc. PAGE NUMBER : C4 OF C12 TEL : 886-2-2696-2468 ISSUED DATE : Mar. 10, 2010 FAX : 886-2-2696-2255 FCC TEST REPORT SPORTON International Inc. PAGE NUMBER : C5 OF C12 TEL : 886-2-2696-2468 ISSUED DATE : Mar. 10, 2010 FAX : 886-2-2696-2255 FCC TEST REPORT SPORTON International Inc. PAGE NUMBER : C6 OF C12 TEL : 886-2-2696-2468 ISSUED DATE : Mar. 10, 2010 FAX : 886-2-2696-2255 FCC TEST REPORT SPORTON International Inc. PAGE NUMBER : C7 OF C12 TEL : 886-2-2696-2468 ISSUED DATE : Mar. 10, 2010 FAX : 886-2-2696-2255 FCC TEST REPORT SPORTON International Inc. PAGE NUMBER : C8 OF C12 TEL : 886-2-2696-2468 ISSUED DATE : Mar. 10, 2010 FAX : 886-2-2696-2255 FCC TEST REPORT SPORTON International Inc. PAGE NUMBER : C9 OF C12 TEL : 886-2-2696-2468 ISSUED DATE : Mar. 10, 2010 FAX : 886-2-2696-2255 FCC TEST REPORT SPORTON International Inc. PAGE NUMBER : C10 OF C12 TEL : 886-2-2696-2468 ISSUED DATE : Mar. 10, 2010 FAX : 886-2-2696-2255 FCC TEST REPORT SPORTON International Inc. PAGE NUMBER : C11 OF C12 TEL : 886-2-2696-2468 ISSUED DATE : Mar. 10, 2010 FAX : 886-2-2696-2255

FCC TEST REPORT Report No.: FR012145 Page No. : A1 of A3 FCC ID : TNU-EQN2201-W Appendix A. Maximum Permissible Exposure FCC TEST REPORT Report No.: FR012145 Page No. : A2 of A3 FCC ID : TNU-EQN2201-W 1. Maximum Permissible Exposure 1.1. Applicable Standard Systems operating under the provisions of this section shall be operated in a manner that ensures that the public is not exposed to radio frequency energy levels in excess limit for maximum permissible exposure. In accordance with 47 CFR FCC Part 2 Subpart J, section 2.1091 this device has been defined as a mobile device whereby a distance of 0.2 m normally can be maintained between the user and the device. (A) Limits for Occupational / Controlled Exposure Frequency Range (MHz) Electric Field Strength (E) (V/m) Magnetic Field Strength (H) (A/m) Power Density (S) (mW/ cm²) Averaging Time |E|²,|H|² or S (minutes) 0.3-3.0 614 1.63 (100)* 6 3.0-30 1842 / f 4.89 / f (900 / f)* 6 30-300 61.4 0.163 1.0 6 300-1500 F/300 6 1500-100,000 5 6 (B) Limits for General Population / Uncontrolled Exposure Frequency Range (MHz) Electric Field Strength (E) (V/m) Magnetic Field Strength (H) (A/m) Power Density (S) (mW/ cm²) Averaging Time |E|²,|H|² or S (minutes) 0.3-1.34 614 1.63 (100)* 30 1.34-30 824/f 2.19/f (180/f)* 30 30-300 27.5 0.073 0.2 30 300-1500 F/1500 30 1500-100,000 1.0 30 Note: f = frequency in MHz ; *Plane-wave equivalent power density 1.2. MPE Calculation Method E (V/m) ＝ d GP30 Power Density: Pd (W/m²) ＝ 377 2 E E ＝ Electric field (V/m) P ＝ Peak RF output power (W) G ＝ EUT Antenna numeric gain (numeric) d ＝ Separation distance between radiator and human body (m) The formula can be changed to Pd ＝ 2 377 30 d GP   From the peak EUT RF output power, the minimum mobile separation distance, d=0.2m, as well as the gain of the used antenna, the RF power density can be obtained. FCC TEST REPORT Report No.: FR012145 Page No. : A3 of A3 FCC ID : TNU-EQN2201-W 1.3. Calculated Result and Limit Antenna Type : PCB Antenna Max Conducted Power for IEEE 802.11b/g: 23.12dBm Test Mode Min. User Distance (cm) Gain (dBi) Numeric Gain Conducted Power (dBm) Conducted Power (mW) Power Density (mW/cm2) 2.4G 20 2 1.584893 23.12 205.1162 0.0647

FCC TEST REPORT Report No.: FR012145 SPORTON International Inc. Report Format Version: a FCC RADIO TEST REPORT according to 47 CFR FCC Part 15 Subpart C § 15.247 Equipment : IP Camera Model No. : EQN22 Series Brand Name : EverFocus Filing Type : New Application Applicant : EverFocus Electronics Corp. 12F-1, No. 79, Sec. 1, Shin-Tai Wu Rd., Hsi-Chih Taipei Hsien, Taiwan FCC ID : TNU-EQN2201-W Manufacturer : EverFocus Electronics Corp. 2F., No. 8, Lane 270, Sec. 3, Beishen Rd., Shenkeng Towanship, Taipei County 222, Taiwan EVERFOCUS ELECTRONICS (BEIJING) CORP. 4F, NO. 2, D4 BUILDING, LIYUAN INDUSTRIAL PARK, LANGXIN COMMUNITY, SHIYAN STREET, BAOAN DISTRICT, SHENZHEN CITY, GUANGDONG PROVINCE, CHINA. Received Date : Feb. 24, 2010 Final Test Date : Mar. 04, 2010 Statement Test result included is only for the 802.11b/g part of the product. The test result in this report refers exclusively to the presented test model / sample. Without written approval of SPORTON International Inc., the test report shall not be reproduced except in full. The measurements and test results shown in this test report were made in accordance with the procedures and found in compliance with the limit given in ANSI C63.4-2003 and 47 CFR FCC Part 15 Subpart C. The test equipment used to perform the test is calibrated and traceable to NML/ROC. SPORTON International Inc. 6F, No. 106, Sec. 1, Hsin Tai Wu Rd., Hsi Chih, Taipei Hsien, Taiwan, R.O.C. FCC TEST REPORT Report No.: FR012145 SPORTON International Inc. Page No. : i of ii TEL : 886-2-2696-2468 Issued Date : Mar. 10, 2010 FAX : 886-2-2696-2255 FCC ID : TNU-EQN2201-W Table of Contents 1 SUMMARY OF THE TEST RESULT ...................................................................................................................... 2 2 GENERAL INFORMATION..................................................................................................................................... 3 2.1 Product Details ........................................................................................................................................................................................ 3 2.2 Accessories ............................................................................................................................................................................................. 3 2.3 Table for Filed Antenna ........................................................................................................................................................................... 3 2.4 Table for Carrier Frequencies ................................................................................................................................................................. 3 2.5 Table for Test Modes .............................................................................................................................................................................. 4 2.6 Table for Testing Locations ..................................................................................................................................................................... 4 2.7 Table for Supporting Units....................................................................................................................................................................... 4 2.8 Table for Parameters of Test Software Setting ....................................................................................................................................... 5 2.9 EUT Operation during Test ..................................................................................................................................................................... 5 2.10 Test Configuration ................................................................................................................................................................................... 6 3 TEST RESULT ........................................................................................................................................................ 8 3.1 AC Power Line Conducted Emissions Measurement.............................................................................................................................. 8 3.2 Maximum Conducted Output Power Measurement .............................................................................................................................. 12 3.3 Power Spectral Density Measurement .................................................................................................................................................. 14 3.4 6dB Spectrum Bandwidth Measurement............................................................................................................................................... 20 3.5 Radiated Emissions Measurement........................................................................................................................................................ 26 3.6 Band Edge and Fundamental Emissions Measurement ....................................................................................................................... 44 3.7 Antenna Requirements.......................................................................................................................................................................... 49 4 LIST OF MEASURING EQUIPMENTS ................................................................................................................. 50 5 TEST LOCATION.................................................................................................................................................. 52 6 TAF CERTIFICATE OF ACCREDITATION .......................................................................................................... 53 APPENDIX A. MAXIMUM PERMISSIBLE EXPOSURE.................................................................................. A1 ~ A3 APP…

Text truncated - open the document above for the full version.

FCC TEST REPORT Report No.: FR012145 Page No. : B1 of B6 FCC ID : TNU-EQN2201-W Appendix B. Test Photos FCC TEST REPORT Report No.: FR012145 Page No. : B2 of B6 FCC ID : TNU-EQN2201-W 1 Photographs of Conducted Emissions Test Configuration FRONT VIEW REAR VIEW FCC TEST REPORT Report No.: FR012145 Page No. : B3 of B6 FCC ID : TNU-EQN2201-W SIDE VIEW FCC TEST REPORT Report No.: FR012145 Page No. : B4 of B6 FCC ID : TNU-EQN2201-W 2 Photographs of Radiated Emissions Test Configuration For radiated emissions 9kHz~30MHz FRONT VIEW REAR VIEW FCC TEST REPORT Report No.: FR012145 Page No. : B5 of B6 FCC ID : TNU-EQN2201-W For radiated emissions 30MHz~1GHz FRONT VIEW REAR VIEW FCC TEST REPORT Report No.: FR012145 Page No. : B6 of B6 FCC ID : TNU-EQN2201-W For radiated emissions above 1GHz FRONT VIEW REAR VIEW