U6A-WU319D11n DUAL-BAND USB DONGLE

1 E-TOP 11n Dual-Band USB Dongle User Guide of WU319d Installing the software of USB Adapter................................................3 Configuring your wireless network (with Wireless Utility)......5 Wi-Fi Protect Setup (WPS)..........................................................................12 Pin Input Config (PIN)...........................................................................12 Push Button (PBC)...................................................................................17 Radio Off.................................................................................................................20 Disable Adapter..................................................................................................21 Uninstalling the software.............................................................................25 Wireless Zero Configuration Troubleshooting.................................27 2 Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: . Reorient or relocate the receiving antenna. . Increase the separation between the equipment and receiver. . Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. . Consult the dealer or an experienced radio/TV technician for help. FCC Part 15.19 Caution: 1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation 2. This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter. 3. Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user authority to operate the equipment. IMPORTANT NOTE: FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. 802.11a (UNII) RF exposure statement According to FCC 15.407(e), the device is intended to operate in the frequency band of 5.15GHz to 5.25GHz under all conditions of normal operation. Normal operation of this device is restricted to indoor used only to reduce any potential for harmful interference to co-channel MSS operations. 3 Installing the software of USB Adapter 1. Select the setup file to install. The setup program will detect user’s language automatically. 2. The setup program will install the driver and utility to computer. Please click the “Next” button to continue. 3. The software installation should begin. This may take a few minutes. 4 4. Once the installation success, click “Yes” to restart your system (recommended). Otherwise, click “No” to restart your system later. 5. Once the installation complete, you may now configure your wireless network. 5 Configuring your wireless network (with Wireless Utility) 1. Windows XP users, if you chose “Microsoft Zero Configuration Tool” during the software installation please skip to page 11. 2. Double click on the computer with wireless signal icon in your taskbar or the shortcut icon on the desktop. 3. It should pop up the Wireless Utility window. And then utility shows the connecting wireless network that connected automatically or was the default network in profile. 6 4. Click the “Available Network” tab to the wireless network surveying page. Click the “Refresh” button to scan the area for wireless network(s). Once the scan completed, select the desired wireless network from the list and double click it or click the “Add to Profile” button. 7 5. It should pop up the wireless Network Properties window. If you do not have any wireless security (WEP, WPA, WPA2, and etc.) set on your wireless network, simply click the “OK” button and skip to step7. If you do have wireless securities on your wireless network, configure the security setting in “Wireless network security” column. 8 6. Set your wireless securities settings, when it completed, click the “OK” button. Select the Network Authentication and Data encryption to set the encryption type. - If you have WEP, typically you select the format and enter your WEP key below the Data encryption. - If you have WPA-PSK or WPA2-PSK, typically you only enter your key in the “Network Key” and type again to confirm it. - If you have 802.1x configure, typically you only configure your setting in 802.1x configure column. 9 7. After connected to wireless network, utility will back to “General” page and show the wireless network status. Once the wireless network connected successfully, the Network Address will show the dongle has gotten the IP address from DHCP. 10 8. Click the “Profile” tab to check the profile page. The wireless network configuration has added in Available Profile(s). It could remove, edit, duplicate and set default the profiles in this page. 11 12 Wi-Fi Protect Setup (WPS) WPS is an easy and secure setup solution for Wi-Fi network. Please click the Wi-Fi Protect Setup tab. dongle has two methods, PIN (Pin Input Config) and PBC (Push…

Text truncated - open the document above for the full version.

Compliance Certification Services Inc. Report No.：T111226A01 Page A1 / 6 External Photo (WU319d) Compliance Certification Services Inc. Report No.：T111226A01 Page A2 / 6 Compliance Certification Services Inc. Report No.：T111226A01 Page A3 / 6

SUJEN 2012.01.10 Nonbrand 3LSWU319DNBSX1XX WU319D 300% 128 128 FCC ID:U6A-WU319D 22*18mm 22mm 18mm

SUJEN 2012.01.10 Nonbrand 3LSWU319DNBSX1XX WU319D 300% 128 128 FCC ID:U6A-WU319D 22*18mm 22mm 18mm

Compliance Certification Services Inc. Report No.：T111226A01 Page A4 / 6 Inernal Photo (WU319d) Compliance Certification Services Inc. Report No.：T111226A01 Page A5 / 6 Compliance Certification Services Inc. Report No.：T111226A01 Page A6 / 6

Date: Antenna 0 Yong-Shun P/N Production Description Version Customer P/N AN-152RRSU00 APPROVAL SHEET Customers: ≖㜧⤴✗ᤘ⍶ᘩ᜘⠑ᐔᔩ 2011/5/6                                         YONG-SHUN Technology Co., LTD. 唡塵✗ᤘ᜘⠑ᐔᔩ 唡塵✗ᤘ᜘⠑ᐔᔩ唡塵✗ᤘ᜘⠑ᐔᔩ 唡塵✗ᤘ᜘⠑ᐔᔩ Address: No.29, Xikun 1st St., Banqiao Dist., New Taipei City 220, Taiwan (R.O.C.) Tel: +886-2-26841827 Fax: +886-2-26835010 Xinxie Technology Co., LTD. (Shenzhen) ⊐ₖ✗ᤘ᜘⠑ᐔᔩ ⊐ₖ✗ᤘ᜘⠑ᐔᔩ⊐ₖ✗ᤘ᜘⠑ᐔᔩ ⊐ₖ✗ᤘ᜘⠑ᐔᔩ (㕓ᙩ元 㕓ᙩ元㕓ᙩ元 㕓ᙩ元 ) Address: Nanbiantou Industrial Area, Dongfang Village, Songgang Town, Shenzhen City, China Tel+86-755-27553831 Fax+86-755-27092799            Table of Contents Item 1. Drawing 2. Test Report -Electrical test 3. Material Certifications -Cable   4. Packing -PE Bag -Carton Modification History: REV.Content 0  Date  PolarizationVertical      Standard connectorReverse SMA PLUG Frequency range Impedance V.S.W.R Radia tion Gain3dBi/3dBi  Whip Electrical Properties Mechanical Properties 2.4GHz/5.XGHz 50Ω ဳ2.0     Electrical Test 2400MHz 2450MHz 2500MHz 4900MHz 5150MHz 5550MHz 5850MHz Antenna Efficiency CABLE SPECIFICATION 䢅ᔧ㊅☉

Test modes: (1) Horizontal Down: (1-1) Horizontal Down Up90( 5 mm separation from the flat phantom for the bottom of the dongle ) (1-2) Horizontal Down Up90( 10 mm separation from the flat phantom for the end of the dongle (opposite from the USB connector) ) 10mm 5mm Compliance Certification Services Inc. Report No: T111226A01-SF USB extension cable: Length is ≦ 5cm (including connector) Compliance Certification Services Inc. Report No: T111226A01-SF EUT Photo WLAN antenna

Date/Time: 2012/04/14 12:50:28 PM Test Laboratory: Compliance Certification Services Inc. D2450V2 SN-728 Body DUT: Dipole 2450 MHz; Type: D2450V2; Serial: D2450V2 - SN:728 Communication System: CW2450; Frequency: 2450 MHz;Duty Cycle: 1:1 Medium parameters used: f = 2450 MHz; σ = 1.97 mho/m; ε r = 51.6; ρ = 1000 kg/m 3 Phantom section: Flat Section Air Temperature:24.2 deg C;Liquid Temperature:23.2 deg C Area Scan Find Secondary Maximum Within 2dB and with a peak SAR value greater than 0.0012W/kg DASY4 Configuration: lProbe: EX3DV4 - SN3801; ConvF(6.79, 6.79, 6.79); lSensor-Surface: 2.5mm (Mechanical Surface Detection) lElectronics: DAE4 Sn558; Calibrated: 2011/7/26 lPhantom: ELI 4.0; Type: QDOVA001BA; Serial: 1052 lMeasurement SW: DASY4, V4.7 Build 80; Postprocessing SW: SEMCAD, V1.8 Build 186 Pin=250mW,d=10mm/Area Scan (6x6x1): Measurement grid: dx=15mm, dy=15mm Maximum value of SAR (measured) = 13.8 mW/g Pin=250mW,d=10mm/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = 98.1 V/m; Power Drift = -0.034 dB Peak SAR (extrapolated) = 26.8 W/kg SAR(1 g) = 13.1 mW/g; SAR(10 g) = 6.13 mW/g Maximum value of SAR (measured) = 17.9 mW/g Pin=250mW,d=10mm/Z Scan (1x1x21): Measurement grid: dx=20mm, dy=20mm, dz=5mm Maximum value of SAR (measured) = 18.2 mW/g .. Date/Time: 2012/04/15 09:55:25 AM Test Laboratory: Compliance Certification Services Inc. D5GHz V2 SN 1004 DUT: Dipole 5GHz ; Type: D5GHz V2; Serial: 1004 Communication System: CW5GHz; Frequency: 5200 MHz;Duty Cycle: 1:1 Medium parameters used: f = 5200 MHz; σ = 5.37 mho/m; ε r = 48.3; ρ = 1000 kg/m 3 Phantom section: Flat Section Air Temperature:24.2 deg C;Liquid Temperature:23.2 deg C Area Scan Find Secondary Maximum Within 2dB and with a peak SAR value greater than 0.0012W/kg DASY4 Configuration: lProbe: EX3DV4 - SN3554; ConvF(3.68, 3.68, 3.68); lSensor-Surface: 2.5mm (Mechanical Surface Detection) lElectronics: DAE4 Sn558; Calibrated: 2011/7/26 lPhantom: ELI 4.0; Type: QDOVA001BA; Serial: 1052 lMeasurement SW: DASY4, V4.7 Build 80; Postprocessing SW: SEMCAD, V1.8 Build 186 Pin=100mW,d=10mm f=5200MHz/Area Scan (8x8x1): Measurement grid: dx=10mm, dy=10mm Maximum value of SAR (measured) = 9.99 mW/g Pin=100mW,d=10mm f=5200MHz/Zoom Scan (8x8x10)/Cube 0: Measurement grid: dx=4mm, dy=4mm, dz=2.5mm Reference Value = 56.4 V/m; Power Drift = -0.133 dB Peak SAR (extrapolated) = 28.5 W/kg SAR(1 g) = 7.88 mW/g; SAR(10 g) = 2.31 mW/g Maximum value of SAR (measured) = 14.4 mW/g Pin=100mW,d=10mm f=5200MHz/Z Scan (1x1x21): Measurement grid: dx=20mm, dy=20mm, dz=5mm Maximum value of SAR (measured) = 6.26 mW/g Date/Time: 2012/04/15 10:50:21 AM Test Laboratory: Compliance Certification Services Inc. D5GHz V2 SN 1004 DUT: Dipole 5GHz ; Type: D5GHz V2; Serial: 1004 Communication System: CW5GHz; Frequency: 5500 MHz;Duty Cycle: 1:1 Medium parameters used: f = 5500 MHz; σ = 5.83 mho/m; ε r = 47.7; ρ = 1000 kg/m 3 Phantom section: Flat Section Air Temperature:24.2 deg C;Liquid Temperature:23.2 deg C Area Scan Find Secondary Maximum Within 2dB and with a peak SAR value greater than 0.0012W/kg DASY4 Configuration: lProbe: EX3DV4 - SN3554; ConvF(3.43, 3.43, 3.43); lSensor-Surface: 2.5mm (Mechanical Surface Detection) lElectronics: DAE4 Sn558; Calibrated: 2011/7/26 lPhantom: ELI 4.0; Type: QDOVA001BA; Serial: 1052 lMeasurement SW: DASY4, V4.7 Build 80; Postprocessing SW: SEMCAD, V1.8 Build 186 Pin=100mW,d=10mm f=5500MHz/Area Scan (8x8x1): Measurement grid: dx=10mm, dy=10mm Maximum value of SAR (measured) = 10.7 mW/g Pin=100mW,d=10mm f=5500MHz/Zoom Scan (8x8x10)/Cube 0: Measurement grid: dx=4mm, dy=4mm, dz=2.5mm Reference Value = 57.2 V/m; Power Drift = -0.078 dB Peak SAR (extrapolated) = 31.8 W/kg SAR(1 g) = 8.51 mW/g; SAR(10 g) = 2.45 mW/g Maximum value of SAR (measured) = 15.7 mW/g Pin=100mW,d=10mm f=5500MHz/Z Scan (1x1x21): Measurement grid: dx=20mm, dy=20mm, dz=5mm Maximum value of SAR (measured) = 6.25 mW/g Date/Time: 2012/04/15 11:38:45 AM Test Laboratory: Compliance Certification Services Inc. D5GHz V2 SN 1004 DUT: Dipole 5GHz ; Type: D5GHz V2; Serial: 1004 Communication System: CW5GHz; Frequency: 5800 MHz;Duty Cycle: 1:1 Medium parameters used: f = 5800 MHz; σ = 6.21 mho/m; ε r = 47.1; ρ = 1000 kg/m 3 Phantom section: Flat Section Air Temperature:24.2 deg C;Liquid Temperature:23.2 deg C Area Scan Find Secondary Maximum Within 2dB and with a peak SAR value greater than 0.0012W/kg DASY4 Configuration: lProbe: EX3DV4 - SN3554; ConvF(3.24, 3.24, 3.24); lSensor-Surface: 2.5mm (Mechanical Surface Detection) lElectronics: DAE4 Sn558; Calibrated: 2011/7/26 lPhantom: ELI 4.0; Type: QDOVA001BA; Serial: 1052 lMeasurement SW: DASY4, V4.7 Build 80; Postprocessing SW: SEMCAD, V1.8 Build 186 Pin=100mW,d=10mm f=5800MHz/Area Scan (8x8x1): Measurement grid: dx=10mm, dy=10mm Maximum value of SAR (measured) = 10.9 mW/g Pin=100mW,d=10mm f=5800MHz/Zoom Scan (8x8x10)/Cube 0: Measurement grid: dx=4mm, dy=4mm, dz=2.5mm Reference Value = 52.7 V/m; Power Drift = -0.104 dB Peak SAR (extrapolated) = 26.5 W/kg SAR(1 g) = 7.38 mW/g; SAR(10 g) = 2.23 mW/g Maximum value of SAR (measured) = 13.9 mW/g Pin=100mW,d=10mm f=5800MHz/Z Scan (1x1x21): Measurement grid: dx=20mm, dy=20mm, dz=5mm Maximum value of SAR (measured) = 5.63 mW/g Date/Time: 2012/06/04 11:28:15 AM Test Laboratory: Compliance Certification Services Inc. D2450V2 SN-728 Body DUT: Dipole 2450 MHz; Type: D2450V2; Serial: D2450V2 - SN:728 Communication System: CW2450; Frequency: 2450 MHz;Duty Cycle: 1:1 Medi um parameters used: f = 2450 MHz; σ = 1.96 mho/m; ε r = 51.8; ρ = 1000 kg/m 3 Phantom section: Flat Section Air Temperature:24.2 deg C;Liquid Temperature:23.2 deg C Area Scan Find Secondary Maximum Within 2dB and with a peak SAR value greater than 0.0012W/kg DASY 4 Configuration: lProbe: EX3DV4 - SN3554; ConvF(6.18, 6.18, 6.18); lS ensor-Surface: 2.5mm (Mechanical Surface Detection) lElectronics: DAE4 Sn558; Calibrated: 2011/7/26 lPhantom: Flat Phantom ELI4.0; Type: QDOVA001BA; Serial: SN: 1052 lM…

Text truncated - open the document above for the full version.

GetAttachment.html (JPEG Image, 732x846 pixels) - Scaled (75%)http://apps.fcc.gov/kdb/GetAttachment.html?id=40434 1 of 14/11/2012 4:56 P M

'DWH7LPH30 7HVW/DERUDWRU\&RPSOLDQFH&HUWLILFDWLRQ6HUYLFHV,QF  E+RUL]RQWDO'RZQDQW$8SPP &RPPXQLFDWLRQ6\VWHP,(((E:/$1)UHTXHQF\0+]'XW\&\FOH 0HGLXPSDUDPHWHUVXVHGI 0+]ı PKRPİ U  ȡ NJP    3KDQWRPVHFWLRQ)ODW6HFWLRQ $LU7HPSHUDWXUHGHJ&/LTXLG7HPSHUDWXUHGHJ& $UHD6FDQ)LQG6HFRQGDU\0D[LPXP:LWKLQG%DQGZLWKDSHDN6$5YDOXHJUHDWHUWKDQ:NJ '$6<&RQILJXUDWLRQ z3UREH(;'961&RQY)   z6HQVRU6XUIDFHPP 0HFKDQLFDO6XUIDFH'HWHFWLRQ  z(OHFWURQLFV'$(6Q&DOLEUDWHG z3KDQWRP)ODW3KDQWRP(/,7\SH4'29$%$6HULDO61 z0HDVXUHPHQW6:'$6<9%XLOG3RVWSURFHVVLQJ6:6(0&$'9%XLOG  +LJK&+0$UHD6FDQ [[ 0HDVXUHPHQWJULGG[ PPG\ PP 0D[LPXPYDOXHRI6$5 PHDVXUHG  P:J  +LJK&+0=RRP6FDQ [[ &XEH0HDVXUHPHQWJULGG[ PPG\ PPG] PP 5HIHUHQFH9DOXH 9P3RZHU'ULIW G% 3HDN6$5 H[WUDSRODWHG  :NJ 6$5 J  P:J6$5 J  P:J 0D[LPXPYDOXHRI6$5 PHDVXUHG  P:J 'DWH7LPH30 7HVW/DERUDWRU\&RPSOLDQFH&HUWLILFDWLRQ6HUYLFHV,QF  E+RUL]RQWDO'RZQDQW$8SPP &RPPXQLFDWLRQ6\VWHP,(((E:/$1)UHTXHQF\0+]'XW\&\FOH 0HGLXPSDUDPHWHUVXVHGI 0+]ı PKRPİ U  ȡ NJP    3KDQWRPVHFWLRQ)ODW6HFWLRQ $LU7HPSHUDWXUHGHJ&/LTXLG7HPSHUDWXUHGHJ& $UHD6FDQ)LQG6HFRQGDU\0D[LPXP:LWKLQG%DQGZLWKDSHDN6$5YDOXHJUHDWHUWKDQ:NJ '$6<&RQILJXUDWLRQ z3UREH(;'961&RQY)   z6HQVRU6XUIDFHPP 0HFKDQLFDO6XUIDFH'HWHFWLRQ  z(OHFWURQLFV'$(6Q&DOLEUDWHG z3KDQWRP)ODW3KDQWRP(/,7\SH4'29$%$6HULDO61 z0HDVXUHPHQW6:'$6<9%XLOG3RVWSURFHVVLQJ6:6(0&$'9%XLOG  +LJK&+0$UHD6FDQ [[ 0HDVXUHPHQWJULGG[ PPG\ PP 0D[LPXPYDOXHRI6$5 PHDVXUHG  P:J  +LJK&+0=RRP6FDQ [[ &XEH0HDVXUHPHQWJULGG[ PPG\ PPG] PP 5HIHUHQFH9DOXH 9P3RZHU'ULIW G% 3HDN6$5 H[WUDSRODWHG  :NJ 6$5 J  P:J6$5 J  P:J 0D[LPXPYDOXHRI6$5 PHDVXUHG  P:J 'DWH7LPH30 7HVW/DERUDWRU\&RPSOLDQFH&HUWLILFDWLRQ6HUYLFHV,QF  E+RUL]RQWDO'RZQDQW%8SPP &RPPXQLFDWLRQ6\VWHP,(((E:/$1)UHTXHQF\0+]'XW\&\FOH 0HGLXPSDUDPHWHUVXVHGI 0+]ı PKRPİ U  ȡ NJP    3KDQWRPVHFWLRQ)ODW6HFWLRQ $LU7HPSHUDWXUHGHJ&/LTXLG7HPSHUDWXUHGHJ& $UHD6FDQ)LQG6HFRQGDU\0D[LPXP:LWKLQG%DQGZLWKDSHDN6$5YDOXHJUHDWHUWKDQ:NJ '$6<&RQILJXUDWLRQ z3UREH(;'961&RQY)   z6HQVRU6XUIDFHPP 0HFKDQLFDO6XUIDFH'HWHFWLRQ  z(OHFWURQLFV'$(6Q&DOLEUDWHG z3KDQWRP)ODW3KDQWRP(/,7\SH4'29$%$6HULDO61 z0HDVXUHPHQW6:'$6<9%XLOG3RVWSURFHVVLQJ6:6(0&$'9%XLOG  +LJK&+0$UHD6FDQ [[ 0HDVXUHPHQWJULGG[ PPG\ PP 0D[LPXPYDOXHRI6$5 PHDVXUHG  P:J  +LJK&+0=RRP6FDQ [[ &XEH0HDVXUHPHQWJULGG[ PPG\ PPG] PP 5HIHUHQFH9DOXH 9P3RZHU'ULIW G% 3HDN6$5 H[WUDSRODWHG  :NJ 6$5 J  P:J6$5 J  P:J 0D[LPXPYDOXHRI6$5 PHDVXUHG  P:J 'DWH7LPH30 7HVW/DERUDWRU\&RPSOLDQFH&HUWLILFDWLRQ6HUYLFHV,QF  E+RUL]RQWDO'RZQDQW%8SPP &RPPXQLFDWLRQ6\VWHP,(((E:/$1)UHTXHQF\0+]'XW\&\FOH 0HGLXPSDUDPHWHUVXVHGI 0+]ı PKRPİ U  ȡ NJP    3KDQWRPVHFWLRQ)ODW6HFWLRQ $LU7HPSHUDWXUHGHJ&/LTXLG7HPSHUDWXUHGHJ& $UHD6FDQ)LQG6HFRQGDU\0D[LPXP:LWKLQG%DQGZLWKDSHDN6$5YDOXHJUHDWHUWKDQ:NJ '$6<&RQILJXUDWLRQ z3UREH(;'961&RQY)   z6HQVRU6XUIDFHPP 0HFKDQLFDO6XUIDFH'HWHFWLRQ 6HQVRU6XUIDFHPP )L[6XUIDFH  z(OHFWURQLFV'$(6Q&DOLEUDWHG z3KDQWRP)ODW3KDQWRP(/,7\SH4'29$%$6HULDO61 z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ı PKRPİ U  ȡ NJP    3KDQWRPVHFWLRQ)ODW6HFWLRQ $LU7HPSHUDWXUHGHJ&/LTXLG7HPSHUDWXUHGHJ& $UHD6FDQ)LQG6HFRQGDU\0D[LPXP:LWKLQG%DQGZLWKDSHDN6$5YDOXHJUHDWHUWKDQ:NJ '$6<&RQILJXUDWLRQ z3UREH(;'961&RQY)   z6HQVRU6XUIDFHPP 0HFKDQLFDO6XUIDFH'HWHFWLRQ  z(OHFWURQLFV'$(6Q&DOLEUDWHG z3KDQWRP)ODW3KDQWRP(/,7\SH4'29$%$6HULDO61 z0HDVXUHPHQW6:'$6<9%XLOG3RVWSURFHVVLQJ6:6(0&$'9%XLOG  +LJK&+0$UHD6FDQ [[ 0HDVXUHPHQWJULGG[ PPG\ PP 0D[LPXPYDOXHRI6$5 PHDVXUHG  P:J  +LJK&+0=RRP6FDQ [[ &XEH0HDVXUHPHQWJULGG[ PPG\ PPG] PP 5HIHUHQFH9DOXH …

Text truncated - open the document above for the full version.

Compliance Certification Services Inc. FCC ID: U6A-WU319D Report No: T111226A01-SF Note: This report shall not be reproduced except in full, without the written approval of Compliance Certification Services Inc. This document may be altered or revised by Compliance Certification Services Inc. personnel only, and shall be noted in the revision section of the document. Page 1 Total Page: 34 ANSI/IEEE Std. C95.1-1992 In accordance with the requirements of FCC Report and Order: ET Docket 93-62, and OET Bulletin 65 Supplement C FCC SAR TEST REPORT For 11n Dual-Band USB Dongle Model: WU319d Trade Name: E-TOP Issued to E-Top Network Technology Inc. No. 82, Gongye 2nd Rd., Tainan City 70955, Taiwan, R.O.C. Issued by Compliance Certification Services Inc. No. 11, Wugong 6th Rd., Wugu Industrial Park, Taipei Hsien, 248 Taiwan. http://www. ccsrf.com [email protected] Issued Date: July 10, 2012 Compliance Certification Services Inc. Report No: T111226A01-SF Page 2 Revision History Rev. Issue Date Revisions Effect Page Revised By 00 January 03, 2012 Initial Issue ALL Anson Lu 01 May 04, 2012 Revised test data ALL Anson Lu 02 June 06, 2012 Revised test data ALL Anson Lu 03 July 10, 2012 Revised test data ALL Anson Lu Compliance Certification Services Inc. Report No: T111226A01-SF Page 3 TABLE OF CONTENTS 1. CERTIFICATE OF COMPLIANCE (SAR EVALUATION) .........................................................4 2. EUT DESCRIPTION ..........................................................................................................................5 3. REQUIREMENTS FOR COMPLIANCE TESTING DEFINED BY THE FCC ..........................6 4. DOSIMETRIC ASSESSMENT SETUP ............................................................................................6 4.1 MEASUREMENT SYSTEM DIAGRAM.....................................................................................7 4.2 SYSTEM COMPONENTS............................................................................................................8 5. EVALUATION PROCEDURES......................................................................................................11 6. MEASUREMENT UNCERTAINTY ..............................................................................................15 7. EXPOSURE LIMIT ..........................................................................................................................17 8. EUT ARRANGEMENT....................................................................................................................18 8.1 ANTHROPOMORPHIC HEAD PHANTOM.............................................................................18 8.2 DEFINITION OF THE “CHEEK/TOUCH” POSITION ............................................................19 8.3 DEFINITION OF THE “TILTED” POSITION...........................................................................20 9. MEASUREMENT RESULTS ..........................................................................................................21 9.1 TEST LIQUIDS CONFIRMATION............................................................................................21 9.2 SYSTEM PERFORMANCE CHECK.........................................................................................24 9.3 EUT TUNE-UP PROCEDURES AND TEST MODE................................................................27 9.4 SAR MEASUREMENTS RESULTS..........................................................................................30 10. EQUIPMENT LIST & CALIBRATION STATUS.....................................................................32 11. FACILITIES ..................................................................................................................................33 12. REFERENCES ..............................................................................................................................33 13. ATTACHMENTS..........................................................................................................................34 Compliance Certification Services Inc. Report No: T111226A01-SF Page 4 1. CERTIFICATE OF COMPLIANCE (SAR EVALUATION) Applicant: E-Top Network Technology Inc. No. 82, Gongye 2nd Rd., Tainan City 70955, Taiwan, R.O.C. Equipment Under Test: 11n Dual-Band USB Dongle Trade Name: E-TOP Model Number: WU319d Date of Test: April 14 ~ July 10, 2012 Device Category: PORTABLE DEVICES Exposure Category: GENERAL POPULATION/UNCONTROLLED EXPOSURE APPLICABLE STANDARDS STANDARD TEST RESULT FCC OET 65 Supplement C No non-compliance noted Deviation from Applicable Standard None The device was tested by Compliance Certification Services Inc. in accordance with the measurement methods and procedures specified in OET Bulletin 65 Supplement C(Edition 01-01). The test results in this report apply only to the tested sample of the stated device/equipment. Other similar device/equipment will not necessarily produce the same results due to production tolerance and measurement uncertainties. Approved by: Tested by: Alex Wu Anson Lu Section Manager Test Engineer Compliance Certification Services Inc. Compliance Certification Services Inc Compliance Certification Services Inc. Report No: T111226A01-SF Page 5 2. EUT DESCRIPTION Product 11n Dual-Band USB Dongle Model Number WU319d Trade Name E-TOP Model Discrepancy All the specification and layout are identical except they come with different external appearance and model numbers. Frequency Range 802.11b: 2412 ~ 2472 MHz 802.11g: 2412 ~ 2472 MHz 802.11n HT20: 2412 ~ 2472 MHz 802.11n HT40: 2422 ~ 2462 MHz 802.11a: 5180 ~ 5240 MHz / 5260 ~ 5320 MHz / 5500 ~ 5700 MHz / 5745 ~ 5825 MHz 802.11a(HT20): 5180 ~ 5240 MHz / 5260 ~ 5320 MHz / 5500 ~ 5700 MHz / 5745 ~ 5825 MHz 802.11a(HT40): 5190~5230 MHz / 5270 ~ 5310 MHz / 5510~5670 MHz / 5755~5795 MHz Transmit Power(Average) 802.11b: 14.88 dBm 802.11g: 12.19 dBm 802.11n HT20: 14.05 dBm 802.11n HT40: 12.27 dBm 802.11a: 12.27 dBm 802.11a HT20: 10.75 dBm 802.11a HT40: 8.18 dB…

Text truncated - open the document above for the full version.

Compliance Certification Services Inc. Reference No: T110729402-RP1 FCC ID: U6A-WU319D Report No.: T111226A01-RP1-1 Note: This report shall not be reproduced except in full, without the written approval of Compliance Certification Services Inc. This document may be altered or revised by Compliance Certification Services Inc. personnel only, and shall be noted in the revision section of the document. Page 1 / 95 FCC 47 CFR PART 15 SUBPART E TEST REPORT For 11n Dual-Band USB Dongle Model: WU319d Trade Name: E-TOP Issued to E-Top Network Technology Inc. No. 82, Gongye 2nd Rd., Tainan City 70955, Taiwan, R.O.C. Issued by Compliance Certification Services Inc. No.11, Wu-Gong 6th Rd., Wugu Industrial Park, New Taipei City 248, Taiwan (R.O.C.) http://www.ccsrf.com [email protected] Issued Date: January 3, 2012 Compliance Certification Services Inc. Reference No: T110729402-RP1 FCC ID: U6A-WU319D Report No.: T111226A01-RP1-1 Page 2 Revision History Rev. Issue Date Revisions Effect Page Revised By 00 January 3, 2012 Initial Issue ALL Sandy Lin Compliance Certification Services Inc. Reference No: T110729402-RP1 FCC ID: U6A-WU319D Report No.: T111226A01-RP1-1 Page 3 TABLE OF CONTENTS 1. TEST RESULT CERTIFICATION............................................................................................. 4 2. EUT DESCRIPTION .................................................................................................................... 5 3. TEST METHODOLOGY ............................................................................................................. 7 3.1 EUT CONFIGURATION................................................................................................... 7 3.2 EUT EXERCISE.............................................................................................................. 7 3.3 GENERAL TEST PROCEDURES........................................................................................ 7 3.4 FCC PART 15.205 RESTRICTED BANDS OF OPERATIONS................................... 8 3.5 DESCRIPTION OF TEST MODES....................................................................................... 9 4. INSTRUMENT CALIBRATION............................................................................................... 10 4.1 MEASURING INSTRUMENT CALIBRATION............................................................... 10 4.2 MEASUREMENT EQUIPMENT USED................................................................. 10 4.3 MEASUREMENT UNCERTAINTY....................................................................... 11 5. FACILITIES AND ACCREDITATIONS ................................................................................. 12 5.1 FACILITIES................................................................................................................. 12 5.2 EQUIPMENT................................................................................................................ 12 5.3 TABLE OF ACCREDITATIONS AND LISTINGS................................................................ 13 6. SETUP OF EQUIPMENT UNDER TEST ................................................................................ 14 6.1 SETUP CONFIGURATION OF EUT.................................................................................. 14 6.2…

Text truncated - open the document above for the full version.