U8G-P1375Pepwave / Peplink / Pismo Wireless Product

Report No.: 121224E05 Page 1 CONSTRUCTION PHOTOS OF EUT Report No.: 121224E05 Page 2 Report No.: 121224E05 Page 3

(Fig.1) FCC ID: U8G-P1375 FCC LABEL LOCATION The label will be permanently affixed at a conspicuous location on the device. Back View:

Report No.: 121224E05 Page 1 CONSTRUCTION PHOTOS OF EUT Report No.: 121224E05 Page 2 Report No.: 121224E05 Page 3 Report No.: 121224E05 Page 4

FCC ID: U8G-P1375 Report No.: RF121224E05 Operational Description This device is a Wireless device, which operates in both of 2.4GHz and 5GHz bands; the maximum data rate could be up to 150Mbps which OFDM technique. If the signal to noise radio is too poor which could not support 150Mbps, the 11Mbps data rate with DSSS technique will be applied. The transmitter of the EUT is powered by DC 12V from power adapter. The antenna provided to the EUT, please refer to following table. The other instruction, please have a look at the users manual. FCC 15.407(c) states: The device shall automatically discontinue transmission in case of either absence of information to transmit or operational failure. These provisions are not intended to preclude the transmission of control or signaling information or the use of repetitive codes used by certain digital technologies to complete frame or burst intervals. Applicants shall include in their application for equipment authorization a description of how this requirement is met” Data transmission is always initiated by software, which is then pass down through the MAC, through the digital and analog baseband, and finally to the RF chip. Several special packets (ACKs, CTS, PSPoll, etc...) are initiated by the MAC. There are the only ways the digital baseband portion will turn on the RF transmitter, which it then turns off at the end of the packet. Therefore, the transmitter will be on only while one of the aforementioned packets are being transmitted.

Report No.: SA121224E05 1 of 7 Report Format Version 5.0.0 RF EXPOSURE REPORT REPORT NO.: SA121224E05 MODEL NO.: MAX On-The-Go, MAX OTG, Pismo735, MAX Make-It, Balance, MAX, Device Connector, AP One, MAX Connector, Air Connector, Air Switch, Pismo935 FCC ID: U8G-P1375 RECEIVED: Feb. 02, 2013 TESTED: Dec. 20 to 24, 2013 ISSUED: Jan. 03, 2014 APPLICANT: Pismo Labs Technology Limited ADDRESS: FLAT/RM A5, 5/F, HK SPINNERS IND BLDG PHASE 6, 481 CASTLE PEAK ROAD, CHEUNG SHA WAN, HONG KONG. ISSUED BY: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch Hsin Chu Laboratory LAB ADDRESS: No. 81-1, Lu Liao Keng, 9th Ling,Wu Lung Tsuen, Chiung Lin Hsiang, Hsin Chu Hsien 307, Taiwan, R.O.C. This report should not be used by the client to claim product certification, approval, or endorsement by any government agencies. This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the compliance or non-compliance to the specification Report No.: SA121224E05 2 of 7 Report Format Version 5.0.0 TABLE OF CONTENTS RELEASE CONTROL RECORD .................................................................................... 3 1. CERTIFICATION ...................................................................................................... 4 2. RF EXPOSURE LIMIT .............................................................................................. 5 3. MPE CALCULATION FORMULA ............................................................................. 5 4. CLASSIFICATION .................................................................................................... 5 1. CALCULATION RESULT OF MAXIMUM CONDUCTED POWER ........................... 6 Report No.: SA121224E05 3 of 7 Report Format Version 5.0.0 RELEASE CONTROL RECORD ISSUE NO. REASON FOR CHANGE DATE ISSUED SA121224E05 Original release Jan. 03, 2014 Report No.: SA121224E05 4 of 7 Report Format Version 5.0.0 1. CERTIFICATION PRODUCT: Pepwave / Peplink / Pismo Wireless Product BRAND NAME: Peplink / Pepwave / Pismo MODEL NO.: MAX On-The-Go, MAX OTG, Pismo735, MAX Make-It, Balance, MAX, Device Connector, AP One, MAX Connector, Air Connector, Air Switch, Pismo935 TEST SAMPLE: ENGINEERING SAMPLE APPLICANT: Pismo Labs Technology Limited TESTED DATE: Dec. 20 to 24, 2013 STANDARDS: FCC Part 2 (Section 2.1091) FCC OET Bulletin 65, Supplement C (01-01) IEEE C95.1 The above equipment (Model: MAX OTG) has been tested by Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch, and found compliance with the requirement of the above standards. The test record, data evaluation & Equipment Under Test (EUT) configurations represented herein are true and accurate accounts of the measurements of the sample’s EMC characteristics under the conditions specified in this report. PREPARED BY : , DATE: Jan. 03, 2014 ( Elsie Hsu, Specialist ) APPROVED BY : , DATE: Jan. 03, 2014 ( May Chen, Manager ) Report No.: SA121224E05 5 of 7 Report Format Version 5.0.0 2. RF EXPOSURE LIMIT LIMITS FOR MAXIMUM PERMISSIBLE EXPOSURE (MPE) FREQUENCY RANGE (MHz) ELECTRIC FIELD STRENGTH (V/m) MAGNETIC FIELD STRENGTH (A/m) POWER DENSITY (mW/cm 2 ) AVERAGE TIME (minutes) LIMITS FOR GENERAL POPULATION / UNCONTROLLED EXPOSURE 300-1500 ... ... F/1500 30 1500-100,000 ... ... 1.0 30 F = Frequency in MHz 3. MPE CALCULATION FORMULA Pd = (Pout*G) / (4*pi*r 2 ) where Pd = power density in mW/cm 2 Pout = output power to antenna in mW G = gain of antenna in linear scale pi = 3.1416 r = distance between observation point and center of the radiator in cm 4. CLASSIFICATION The antenna of this product, under normal use condition, is at least 20cm away from the body of the user. So, this device is classified as Mobile Device. This product could be applied with one USB Cellular Modem, and the safe distance is 65 cm for collocated radio. Report No.: SA121224E05 6 of 7 Report Format Version 5.0.0 1. CALCULATION RESULT OF MAXIMUM CONDUCTED POWER For WLAN: For 15.247(2.4GHz): FREQUENCY (MHz) MAX POWER (mW) ANTENNA GAIN (dBi) DISTANCE (cm) POWER DENSITY (mW/ cm 2 ) LIMIT (mW/cm 2 ) 2412-2462 948.418 0.83 20 0.22842 1 FREQUENCY (MHz) MAX POWER (mW) ANTENNA GAIN (dBi) DISTANCE (cm) POWER DENSITY (mW/ cm 2 ) LIMIT (mW/cm 2 ) 2412-2462 948.418 0.83 65 0.02163 1 For 15.247(5GHz): FREQUENCY (MHz) MAX POWER (mW) ANTENNA GAIN (dBi) DISTANCE (cm) POWER DENSITY (mW/ cm 2 ) LIMIT (mW/cm 2 ) 5745 ~ 5825 85.507 3.49 20 0.03800 1 FREQUENCY (MHz) MAX POWER (mW) ANTENNA GAIN (dBi) DISTANCE (cm) POWER DENSITY (mW/ cm 2 ) LIMIT (mW/cm 2 ) 5745 ~ 5825 85.507 3.49 65 0.00360 1 For 15.407(5GHz): FREQUENCY (MHz) MAX POWER (mW) ANTENNA GAIN (dBi) DISTANCE (cm) POWER DENSITY (mW/ cm 2 ) LIMIT (mW/cm 2 ) 5180 ~ 5240 46.345 3.49 20 0.02059 1 Report No.: SA121224E05 7 of 7 Report Format Version 5.0.0 For USB Cellular Modem: DEVICE MAX EIRP (mW) MAX EIRP (dBm) DISTANCE (cm) P…

Text truncated - open the document above for the full version.

Report No.: RF121224E05 1 of 99 Report Format Version 5.2.0 FCC TEST REPORT (15.247) REPORT NO.: RF121224E05 MODEL NO.: MAX OTG (Refer to 3.1 for more details) FCC ID: U8G-P1375 RECEIVED: Feb. 02, 2013 TESTED: Feb. 02 and Dec. 21 to 26, 2013 ISSUED: Jan. 03, 2014 APPLICANT: Pismo Labs Technology Limited ADDRESS: FLAT/RM A5, 5/F, HK SPINNERS IND BLDG PHASE 6, 481 CASTLE PEAK ROAD, CHEUNG SHA WAN, HONG KONG. ISSUED BY: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch Hsin Chu Laboratory LAB ADDRESS : No. 81-1, Lu Liao Keng, 9th Ling, Wu Lung Tsuen, Chiung Lin Hsiang, Hsin Chu Hsien 307, Taiwan, R.O.C. TEST LOCATION (1): No. 81-1, Lu Liao Keng, 9th Ling, Wu Lung Tsuen, Chiung Lin Hsiang, Hsin Chu Hsien 307, Taiwan, R.O.C. TEST LOCATION (2): No. 49, Ln. 206, Wende Rd., Shangshan Tsuen, Chiung Lin Hsiang, Hsin Chu Hsien 307, Taiwan, R.O.C. This report should not be used by the client to claim product certification, approval, or endorsement by TAF or any government agencies. This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the compliance or non-compliance to the specification Report No.: RF121224E05 2 of 99 Report Format Version 5.2.0 Table of Contents RELEASE CONTROL RECORD ........................................................................................ 5 1. CERTIFICATION .................................................................................................... 6 2. SUMMARY OF TEST RESULTS ............................................................................ 7 2.1 MEASUREMENT UNCERTAINTY .......................................................................... 8 3. GENERAL INFORMATION ..................................................................................... 9 3.1 GENERAL DESCRIPTION OF EUT ....................................................................... 9 3.2 DESCRIPTION OF TEST MODES ....................................................................... 12 3.2.1 TEST MODE APPLICABILITY AND TESTED CHANNEL DETAIL ........................ 13 3.3 GENERAL DESCRIPTION OF APPLIED STANDARDS ....................................... 16 3.4 DUTY CYCLE OF TEST SIGNAL ......................................................................... 17 3.5 DESCRIPTION OF SUPPORT UNITS .................................................................. 19 3.6 CONFIGURATION OF SYSTEM UNDER TEST ................................................... 20 4. TEST TYPES AND RESULTS (FOR 2.4GHz, 2.400 ~ 2.4835GHz Band) ............. 21 4.1 CONDUCTED EMISSION MEASUREMENT ........................................................ 21 4.1.1 LIMITS OF CONDUCTED EMISSION MEASUREMENT ...................................... 21 4.1.2 TEST INSTRUMENTS .......................................................................................... 21 4.1.3 TEST PROCEDURES .......................................................................................... 22 4.1.4 DEVIATION FROM TEST STANDARD ................................................................. 22 4.1.5 TEST SETUP ....................................................................................................... 22 4.1.6 EUT OPERATING CONDITIONS ......................................................................... 23 4.1.7 TEST RESULTS ................................................................................................... 24 4.2 RADIATED EMISSION AND BANDEDGE MEASUREMENT ................................ 26 4.2.1 LIMITS OF RADIATED EMISSION AND BANDEDGE MEASUREMENT .............. 26 4.2.2 TEST INSTRUMENTS .......................................................................................... 27 4.2.3 TEST PROCEDURES .......................................................................................... 29 4.2.4 DEVIATION FROM TEST STANDARD ................................................................. 29 4.2.5 TEST SETUP ....................................................................................................... 30 4.2.6 EUT OPERATING CONDITIONS ......................................................................... 30 4.2.7 TEST RESULTS ................................................................................................... 31 4.3 6dB BANDWIDTH MEASUREMENT .................................................................... 44 4.3.1 LIMITS OF 6dB BANDWIDTH MEASUREMENT .................................................. 44 4.3.2 TEST INSTRUMENTS .......................................................................................... 44 4.3.3 TEST PROCEDURE ............................................................................................. 44 4.3.4 DEVIATION FROM TEST STANDARD ................................................................. 44 4.3.5 TEST SETUP .................................................…

Text truncated - open the document above for the full version.

Report No.: RF121224E05-1 1 of 57 Report Format Version 5.2.0 Cancels and replaces the report No.: RF131111E02 dated Sep. 02, 2013 FCC TEST REPORT (15.407) REPORT NO.: RF121224E05-1 MODEL NO.: MAX OTG(Refer to 3.1 for more details) FCC ID: U8G-P1375 RECEIVED: Dec. 24, 2012 TESTED: Feb. 22 to Dec. 26, 2013 ISSUED: Jan. 03, 2014 APPLICANT: Pismo Labs Technology Limited ADDRESS: FLAT/RM A5, 5/F, HK SPINNERS IND BLDG PHASE 6, 481 CASTLE PEAK ROAD, CHEUNG SHA WAN, HONG KONG. ISSUED BY: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch Hsin Chu Laboratory LAB ADDRESS : No. 81-1, Lu Liao Keng, 9th Ling, Wu Lung Tsuen, Chiung Lin Hsiang, Hsin Chu Hsien 307, Taiwan, R.O.C. TEST LOCATION (1): No. 81-1, Lu Liao Keng, 9th Ling, Wu Lung Tsuen, Chiung Lin Hsiang, Hsin Chu Hsien 307, Taiwan, R.O.C. TEST LOCATION (2): No. 49, Ln. 206, Wende Rd., Shangshan Tsuen, Chiung Lin Hsiang, Hsin Chu Hsien 307, Taiwan, R.O.C. This report should not be used by the client to claim product certification, approval, or endorsement by TAF or any government agencies. This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the compliance or non-compliance to the specification Report No.: RF121224E05-1 2 of 57 Report Format Version 5.2.0 Cancels and replaces the report No.: RF131111E02 dated Sep. 02, 2013 Table of Contents RELEASE CONTROL RECORD..............................................................................4 1. CERTIFICATION ...........................................................................................5 2. SUMMARY OF TEST RESULTS ...................................................................6 2.1 MEASUREMENT UNCERTAINTY ................................................................7 3. GENERAL INFORMATION ...........................................................................8 3.1 GENERAL DESCRIPTION OF EUT ..............................................................8 3.2 DESCRIPTION OF TEST MODES .............................................................. 11 3.2.1 TEST MODE APPLICABILITY AND TESTED CHANNEL DETAIL ..............12 3.3 GENERAL DESCRIPTION OF APPLIED STANDARDS .............................14 3.4 Duty cycle of test signal ...............................................................................15 3.5 DESCRIPTION OF SUPPORT UNITS ........................................................18 3.6 CONFIGURATION OF SYSTEM UNDER TEST .........................................19 4. TEST TYPES AND RESULTS .....................................................................20 4.1 CONDUCTED EMISSION MEASUREMENT ..............................................20 4.1.1 LIMITS OF CONDUCTED EMISSION MEASUREMENT ............................20 4.1.2 TEST INSTRUMENTS ................................................................................20 4.1.3 TEST PROCEDURES .................................................................................21 4.1.4 DEVIATION FROM TEST STANDARD .......................................................21 4.1.5 TEST SETUP ..............................................................................................21 4.1.6 EUT OPERATING CONDITIONS ................................................................22 4.1.7 TEST RESULTS ..........................................................................................23 4.2 RADIATED EMISSION AND BANDEDGE MEASUREMENT ......................25 4.2.1 LIMITS OF RADIATED EMISSION AND BANDEDGE MEASUREMENT ...25 4.2.2 LIMITS OF UNWANTED EMISSION OUT OF THE RESTRICTED BANDS25 4.2.3 TEST INSTRUMENTS ................................................................................26 4.2.4 TEST PROCEDURES .................................................................................28 4.2.5 DEVIATION FROM TEST STANDARD .......................................................28 4.2.6 TEST SETUP ..............................................................................................29 4.2.7 EUT OPERATING CONDITION ..................................................................29 4.2.8 TEST RESULTS ..........................................................................................30 4.3 TRANSMIT POWER MEASUREMENT .......................................................39 4.3.1 LIMITS OF TRANSMIT POWER MEASUREMENT ....................................39 4.3.2 TEST INSTRUMENTS ................................................................................39 4.3.3 TEST PROCEDURE ...................................................................................40 4.3.4 DEVIATION FROM TEST STANDARD .......................................................40 4.3.5 TEST SETUP ..............................................................................................41 4.3.6 EUT OPERATING CONDITIONS ...........................................…

Text truncated - open the document above for the full version.

Report No.: 130725E04 1 of 3 PHOTOGRAPHS OF THE TEST CONFIGURATION CONDUCTED EMISSION TEST Report No.: 130725E04 2 of 3 RADIATED EMISSION TEST (Below 1GHz) Report No.: 130725E04 3 of 3 RADIATED EMISSION TEST (Above 1GHz)