U8G-P1625PEPWAVE WIRELESS PRODUCT

COPYRIGHT & TRADEMARKS Specifications are subject to change without notice. Copyright © 2011 User Manual Document Rev. 1.0 May-11 Page 2 User Manual Table of Contents 1 INTRODUCTION AND SCOPE ................................................................................. 3 2 PRODUCT FEATURES ............................................................................................. 4 3 INSTALLATION ......................................................................................................... 5 3.1 INSTALLATION PROCEDURES .................................................................................................. 5 3.2 QUICK START ........................................................................................................................ 6 Page 3 User Manual 1 Introduction and Scope Access Point Unit (APU) is a carrier-grade 802.11b/g Wi-Fi access point with centralized management system. One device can masquerade up to 16 different access points. Each virtual access point can have its own security policy (e.g. WPA, WPA2, etc.) and authentication mechanism (e.g. 802.1x, open, captive portal, etc), to facilitate building your wholesale network much faster, easier and more cost-effective than ever before. Page 4 User Manual 2 Product Features Key features of devices:  Designed for wholesale wireless networks with m ultiple SSID and VLAN support  Independent security policies and encryption mechanisms per virtual AP  Centralized managed via web based InControl  High-power output enhances coverage and lowers cost of ownership  WMM (Wi-Fi Multimedia) and QoS (Quality of Service) Support  WDS (Wireless Distribution System) Support  Captive Portal Support  Mesh Connector Bridging Page 5 User Manual 3 Installation 3.1 Installation Procedures 1. Attach the antenna to the device. 2. Connect the LAN port on the unit with the backbone network using an Ethernet cable. 3. Connect the power adapter to the power connector of the unit, and then plug in the power adapter. 4. Wait for the status LED to turn green. 5. Connect a PC to the backbone network, and configure the IP address of the PC to be any IP address between 192.168.0.4 and 192.168.0.254, with subnet mask of 255.255.255.0. 6. With Microsoft Internet Explorer 6 or above, or Mozilla Firefox 2.0 or above, connect to the URL https://192.168.0.3. 7. When prompted, enter the default admin login ID and password, admin and public respectively. 8. After logging in, a Main Menu page appears to facilitate further configuration of the unit: Page 6 User Manual 3.2 Quick Start By default, a n access point is preset with SSID: PEPWAVE_XXXX, where XXXX is the last 4 hex digits of the LAN MAC Address of the unit. The default access point bridges the Wi-Fi interface to the Ethernet port, with both encryption and VLAN tagging disabled. To access the backbone network connected via the Ethernet port of the unit, establish a session at the Wi-Fi interface with a Wi-Fi client. After establishing a Wi-Fi client session, information about the established Wi-Fi session appears at the Web Administration Interface of APU device, under the section Information-> Wireless. Clicking on the link labeled Details causes the following screen to be displayed: FCC WARNING This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This device must be installed to provide a separation distance of at least 20 cm from all persons and must not be collocated or operating in conjunction with any other antenna or transmitter. NOTE 1: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help. NOTE 2: Any changes or modifications not expressly approved by the manufacturer could void the user’s authority to operate the equipment. NOTE 3: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user’s authority to operate the equipment.

COPYRIGHT & TRADEMARKS Specifications are subject to change without notice. Copyright © 2011 User Manual Document Rev. 1.0 May-11 Page 2 User Manual Table of Contents 1 INTRODUCTION AND SCOPE ................................................................................. 3 2 PRODUCT FEATURES ............................................................................................. 4 3 INSTALLATION ......................................................................................................... 5 3.1 INSTALLATION PROCEDURES .................................................................................................. 5 3.2 QUICK START ........................................................................................................................ 6 Page 3 User Manual 1 Introduction and Scope Access Point Unit (APU) is a carrier-grade 802.11b/g Wi-Fi access point with centralized management system. One device can masquerade up to 16 different access points. Each virtual access point can have its own security policy (e.g. WPA, WPA2, etc.) and authentication mechanism (e.g. 802.1x, open, captive portal, etc), to facilitate building your wholesale network much faster, easier and more cost-effective than ever before. Page 4 User Manual 2 Product Features Key features of devices:  Designed for wholesale wireless networks with m ultiple SSID and VLAN support  Independent security policies and encryption mechanisms per virtual AP  Centralized managed via web based InControl  High-power output enhances coverage and lowers cost of ownership  WMM (Wi-Fi Multimedia) and QoS (Quality of Service) Support  WDS (Wireless Distribution System) Support  Captive Portal Support  Mesh Connector Bridging Page 5 User Manual 3 Installation 3.1 Installation Procedures 1. Attach the antenna to the device. 2. Connect the LAN port on the unit with the backbone network using an Ethernet cable. 3. Connect the power adapter to the power connector of the unit, and then plug in the power adapter. 4. Wait for the status LED to turn green. 5. Connect a PC to the backbone network, and configure the IP address of the PC to be any IP address between 192.168.0.4 and 192.168.0.254, with subnet mask of 255.255.255.0. 6. With Microsoft Internet Explorer 6 or above, or Mozilla Firefox 2.0 or above, connect to the URL https://192.168.0.3. 7. When prompted, enter the default admin login ID and password, admin and public respectively. 8. After logging in, a Main Menu page appears to facilitate further configuration of the unit: Page 6 User Manual 3.2 Quick Start By default, a n access point is preset with SSID: PEPWAVE_XXXX, where XXXX is the last 4 hex digits of the LAN MAC Address of the unit. The default access point bridges the Wi-Fi interface to the Ethernet port, with both encryption and VLAN tagging disabled. To access the backbone network connected via the Ethernet port of the unit, establish a session at the Wi-Fi interface with a Wi-Fi client. After establishing a Wi-Fi client session, information about the established Wi-Fi session appears at the Web Administration Interface of APU device, under the section Information-> Wireless. Clicking on the link labeled Details causes the following screen to be displayed: FCC WARNING This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This device must be installed to provide a separation distance of at least 20 cm from all persons and must not be collocated or operating in conjunction with any other antenna or transmitter. NOTE 1: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help. NOTE 2: Any changes or modifications not expressly approved by the manufacturer could void the user’s authority to operate the equipment. NOTE 3: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user’s authority to operate the equipment.

Pismolabs Technology Limited Room 1703A, 17/F, Park Building, 476 Castle Peak Road, Cheung Sha Wan, Kowloon, Hong Kong Federal Communications Commission Authorization and Evaluation Division Confidentiality Request regarding application for certification of FCC ID: U8G-P1625 Pursuant to Sections 0.457 and 0.459 of the Commission’s Rules, we hereby request confidential treatment of information accompanying this application as outlined below: Exhibit Type File Name Schematics CONF_U8G-P1625_FCC_Schematics.pdf Block Diagram CONF_U8G-P1625_FCC_BlockDiagram.pdf Operational Description CONF_U8G-P1625_FCC_OperationalDescription.pdf The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. The applicant understands that pursuant to Section 0.457 of the Rules, disclosure of this application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely, Pismolabs Technology Limited

TIMCO ENGINEERING INC. 849 NW State Road 45 Newberry, Florida 32669 http://www.timcoengr.com 888.472.2424 F 352.472.2030 email: [email protected] TCB FCC Approvals FCB Industry Canada Approval NB Notified Body for Europe DECEMBER 19, 2011 Federal Communications Commission Office of Engineering and Technology Laboratory Division 7435 Oakland Mills Rd Columbia MD 21046-1609 Phone: +1-301-362-3000 [email protected] FCCID: U8G-P1265 FCC- It has been brought to our attention that the above listed TCB grant was issued with the incorrect FCCID. The customer has since updated all documents. Thank you. -Timco Engineering

Pismolabs Technology Limited Room 1703A, 17/F, Park Building, 476 Castle Peak Road, Cheung Sha Wan, Kowloon, Hong Kong Federal Communications Commission Authorization and Evaluation Division Confidentiality Request regarding application for certification of FCC ID: U8G-P1625 Pursuant to Sections 0.457 and 0.459 of the Commission’s Rules, we hereby request confidential treatment of information accompanying this application as outlined below: Exhibit Type File Name Schematics CONF_U8G-P1625_FCC_Schematics.pdf Block Diagram CONF_U8G-P1625_FCC_BlockDiagram.pdf Operational Description CONF_U8G-P1625_FCC_OperationalDescription.pdf The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. The applicant understands that pursuant to Section 0.457 of the Rules, disclosure of this application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely, Pismolabs Technology Limited

Pismolabs Technology Limited Model:Pismo 525 REPORT NO.: STR11048093I FCC PART 15.247 EXHIBIT 2 - EUT EXTERNAL PHOTOGRAPHS EUT View 1 EUT View 2 Pismolabs Technology Limited Model:Pismo 525 REPORT NO.: STR11048093I FCC PART 15.247 Antenna View: Antenna Connector View

Pismolabs Technology Limited Model:Pismo 525 REPORT NO.: STR11048093I FCC PART 15.247 EXHIBIT 2 - EUT EXTERNAL PHOTOGRAPHS EUT View 1 EUT View 2 Pismolabs Technology Limited Model:Pismo 525 REPORT NO.: STR11048093I FCC PART 15.247 Antenna View: Antenna Connector View

Pismolabs Technology Limited Model:Pismo 525 REPORT NO.: STR11048093I FCC PART 15.247 EXHIBIT 1- PRODUCT LABELING Proposed FCC ID Label Format FCC ID: U8G-P1625 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Specifications : Text is Black in color and justified. Labels are printed in indelible ink on permanent adhesive silk-screened onto the EUT or shall be affixed at a conspicuous location on the EUT. Proposed Label Location on EUT FCC ID Label Location

Pismolabs Technology Limited Model:Pismo 525 REPORT NO.: STR11048093I FCC PART 15.247 EXHIBIT 1- PRODUCT LABELING Proposed FCC ID Label Format FCC ID: U8G-P1625 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Specifications : Text is Black in color and justified. Labels are printed in indelible ink on permanent adhesive silk-screened onto the EUT or shall be affixed at a conspicuous location on the EUT. Proposed Label Location on EUT FCC ID Label Location

Pismolabs Technology Limited Model:Pismo 525 REPORT NO.: STR11048093I FCC PART 15.247 EXHIBIT 1- PRODUCT LABELING Proposed FCC ID Label Format FCC ID: U8G-P1625 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Specifications : Text is Black in color and justified. Labels are printed in indelible ink on permanent adhesive silk-screened onto the EUT or shall be affixed at a conspicuous location on the EUT. Proposed Label Location on EUT FCC ID Label Location

Pismolabs Technology Limited Model:Pismo 525 REPORT NO.: STR11048093I FCC PART 15.247 EXHIBIT 1- PRODUCT LABELING Proposed FCC ID Label Format FCC ID: U8G-P1625 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Specifications : Text is Black in color and justified. Labels are printed in indelible ink on permanent adhesive silk-screened onto the EUT or shall be affixed at a conspicuous location on the EUT. Proposed Label Location on EUT FCC ID Label Location

Pismolabs Technology Limited Model:Pismo 525 REPORT NO.: STR11048093I FCC PART 15.247 EXHIBIT 3 - EUT INTERNAL PHOTOGRAPHS EUT Housing and Board View Solder Board-Component View 1 Pismolabs Technology Limited Model:Pismo 525 REPORT NO.: STR11048093I FCC PART 15.247 Solder Board-Component View 2 Solder Board-Component View 3

Pismolabs Technology Limited Model:Pismo 525 REPORT NO.: STR11048093I FCC PART 15.247 EXHIBIT 3 - EUT INTERNAL PHOTOGRAPHS EUT Housing and Board View Solder Board-Component View 1 Pismolabs Technology Limited Model:Pismo 525 REPORT NO.: STR11048093I FCC PART 15.247 Solder Board-Component View 2 Solder Board-Component View 3

SKYVERTEX CO., LTD. ADD: 3F, NO. 168, SEC. 2, CHUNG-BEI RD., CHUNG CITY, TAOYUAN 320, TAIWAN TEL: +886-3-4670833 FAX: +886-3-4679947 EMAIL: [email protected] SKYVERTEX COMMUNICATION GROUP HTTP://www.skyvertex.com.tw SPECIFICATION FOR APPROVAL SPECIFICATIONS (USING HP8753ET NETWORK ANALYZER) ANTENNA TYPE Omni-Directional MODEL NO. 1GF-2408B FREQUENCY 2.4GHz~2.5GHz V. S . W. R . ≦1.5 IMPEDANCE 50 OHMS ±5Ω GAIN 8 dBi WITHSTANDING POWER MAX50 W Vertical Beam-with 15∘ Horizontal Beam-with 360∘ WEIGT APPROX 180g ±20g LENGTH 498 m/m ±5 RADOME MATERIAL White Fiberglass CONNECTOR TYPE N TYPE MALE REMARK APPROVAL : CHECK : DWG : Retuen loss & V.S.W.R Retuen loss V. S . W. R Antenna Vertical & Horzontal Pattern Vertical E-plane co-pol ------ 3-dB beam-with=15° Horizontal H-plane co-pol ------ 3-dB beam-with=360°

SKYVERTEX CO., LTD. ADD: 3F, NO. 168, SEC. 2, CHUNG-BEI RD., CHUNG CITY, TAOYUAN 320, TAIWAN TEL: +886-3-4670833 FAX: +886-3-4679947 EMAIL: [email protected] SKYVERTEX COMMUNICATION GROUP HTTP://www.skyvertex.com.tw SPECIFICATION FOR APPROVAL SPECIFICATIONS (USING HP8753ET NETWORK ANALYZER) ANTENNA TYPE Omni-Directional MODEL NO. 1GF-2408B FREQUENCY 2.4GHz~2.5GHz V. S . W. R . ≦1.5 IMPEDANCE 50 OHMS ±5Ω GAIN 8 dBi WITHSTANDING POWER MAX50 W Vertical Beam-with 15∘ Horizontal Beam-with 360∘ WEIGT APPROX 180g ±20g LENGTH 498 m/m ±5 RADOME MATERIAL White Fiberglass CONNECTOR TYPE N TYPE MALE REMARK APPROVAL : CHECK : DWG : Retuen loss & V.S.W.R Retuen loss V. S . W. R Antenna Vertical & Horzontal Pattern Vertical E-plane co-pol ------ 3-dB beam-with=15° Horizontal H-plane co-pol ------ 3-dB beam-with=360°

1. MAXIMUM PERMISSIBLE EXPOSURE (MPE) 1.1 Standard Applicable According to §1.1307(b)(1), system operating under the provisions of this section shall be operating in a manner that the public is not exposed to radio frequency energy level in excess limit for maximum permissible exposure. (a) Limits for Occupational / Controlled Exposure Frequency range (MHz) Electric Field Strength (E) (V/m) Magnetic Field Strength (H) (A/m) Power Density (S) (mW/cm 2 ) Averaging Times | E | 2 , | H | 2 or S (minutes) 0.3-3.0 614 1.63 (100)* 6 3.0-30 1842/f 4.89/f (900/f)* 6 30-300 61.4 0.163 1.0 6 300-1500 / / F/300 6 1500-100000 / / 5 6 (b) Limits for General Population / Uncontrolled Exposure Frequency range (MHz) Electric Field Strength (E) (V/m) Magnetic Field Strength (H) (A/m) Power Density (S) (mW/cm 2 ) Averaging Times | E | 2 , | H | 2 or S (minutes) 0.3-1.34 614 1.63 (100)* 30 1.34-30 824/f 2.19/f (180/f)* 30 30-300 27.5 0.073 0.2 30 300-1500 / / F/1500 30 1500-100000 / / 1 30 Note: f = frequency in MHz: * = Plane-wave equivalents power density 1.2 MPE Calculation Method S = (30*P*G) / (377*R 2 ) S = power density (in appropriate units, e.g., mw/cm 2 ) P = power input to the antenna (in appropriate units, e.g., mw) G = power gain of the antenna in the direction of interest relative to an isotropic radiator, the power gain factor is normally numeric gain. R = distance to the center of radiation of the antenna (in appropriate units, e.g., cm) 1.3 MPE Calculation Result Maximum peak output power at antenna input terminal: 19.26(dBm) Maximum peak output power at antenna input terminal: 84.3335(mW) Prediction distance: >20 (cm) Prediction frequency: 2437 (MHz) Antenna gain (max.): 8 (dBi) Antenna gain (max.): 6.3096 (numeric) The worst case is power density at prediction frequency at 20cm: 0.10586(mw/cm 2 ) MPE limit for general population exposure at prediction frequency: 1 (mw/cm 2 ) 0.10586 (mw/cm 2 ) < 1 (mw/cm 2 ) Result: Pass

1. MAXIMUM PERMISSIBLE EXPOSURE (MPE) 1.1 Standard Applicable According to §1.1307(b)(1), system operating under the provisions of this section shall be operating in a manner that the public is not exposed to radio frequency energy level in excess limit for maximum permissible exposure. (a) Limits for Occupational / Controlled Exposure Frequency range (MHz) Electric Field Strength (E) (V/m) Magnetic Field Strength (H) (A/m) Power Density (S) (mW/cm 2 ) Averaging Times | E | 2 , | H | 2 or S (minutes) 0.3-3.0 614 1.63 (100)* 6 3.0-30 1842/f 4.89/f (900/f)* 6 30-300 61.4 0.163 1.0 6 300-1500 / / F/300 6 1500-100000 / / 5 6 (b) Limits for General Population / Uncontrolled Exposure Frequency range (MHz) Electric Field Strength (E) (V/m) Magnetic Field Strength (H) (A/m) Power Density (S) (mW/cm 2 ) Averaging Times | E | 2 , | H | 2 or S (minutes) 0.3-1.34 614 1.63 (100)* 30 1.34-30 824/f 2.19/f (180/f)* 30 30-300 27.5 0.073 0.2 30 300-1500 / / F/1500 30 1500-100000 / / 1 30 Note: f = frequency in MHz: * = Plane-wave equivalents power density 1.2 MPE Calculation Method S = (30*P*G) / (377*R 2 ) S = power density (in appropriate units, e.g., mw/cm 2 ) P = power input to the antenna (in appropriate units, e.g., mw) G = power gain of the antenna in the direction of interest relative to an isotropic radiator, the power gain factor is normally numeric gain. R = distance to the center of radiation of the antenna (in appropriate units, e.g., cm) 1.3 MPE Calculation Result Maximum peak output power at antenna input terminal: 19.26(dBm) Maximum peak output power at antenna input terminal: 84.3335(mW) Prediction distance: >20 (cm) Prediction frequency: 2437 (MHz) Antenna gain (max.): 8 (dBi) Antenna gain (max.): 6.3096 (numeric) The worst case is power density at prediction frequency at 20cm: 0.10586(mw/cm 2 ) MPE limit for general population exposure at prediction frequency: 1 (mw/cm 2 ) 0.10586 (mw/cm 2 ) < 1 (mw/cm 2 ) Result: Pass

Pismolabs Technology Limited Model: Pismo 525 REPORT NO.: STR11048093I PAGE 1 OF 49 FCC PART 15.247 FCC Part 15C Measurement and Test Report For Pismolabs Technology Limited Room 1703A, 17/F, Park Building, 476 Castle Peak Road, Cheung Sha Wan, Kowloon, HongKong FCC ID: U8G-P1625 Report Concerns: Original Report Equipment Type: Pepwave Wireless Product Model: Pismo 525 Report No.: STR11048093I Test Date: 2011-04-08 to 2011-05-17 Issue Date: 2011-05-31 Tested By: Galy He / Engineer Reviewed By: Lahm Peng / EMC Manager Approved & Authorized By: Jandy so / PSQ Manager Prepared By: SEM.Test Compliance Service Co., Ltd 3/F, Jinbao Commerce Building, Xin'an Fanshen Road, Bao'an District, Shenzhen, P.R.C.（518101） Tel.: +86-755-33663308 Fax.: +86-755-33663309 Website: www.semtest.com.cn Note: This test report is limited to the above client company and the product model only. It may not be duplicated without prior permitted by SEM.Test Compliance Service Co., Ltd . Pismolabs Technology Limited Model: Pismo 525 REPORT NO.: STR11048093I PAGE 2 OF 49 FCC PART 15.247 TABLE OF CONTENTS 1. GENERAL INFORMATION ...................................................................................................................................3 1.1 PRODUCT DESCRIPTION FOR EQUIPMENT UNDER TEST (EUT)...............................................................................3 1.2 TEST STANDARDS...................................................................................................................................................3 1.3 TEST METHODOLOGY.............................................................................................................................................4 1.4 TEST FACILITY.......................................................................................................................................................4 1.5 EUT EXERCISE SOFTWARE....................................................................................................................................4 1.6 ACCESSORIES EQUIPMENT LIST AND DETAILS.......................................................................................................4 1.7 EUT CABLE LIST AND DETAILS.............................................................................................................................4 2. SUMMARY OF TEST RESULTS ...........................................................................................................................5 3. CONDUCTED EMISSIONS ....................................................................................................................................6 3.1 MEASUREMENT UNCERTAINTY..............................................................................................................................6 3.2 TEST EQUIPMENT LIST AND DETAILS.....................................................................................................................6 3.3 TEST PROCEDURE...................................................................................................................................................6 3.4 BASIC TEST SETUP BLOCK DIAGRAM.....................................................................................................................6 3.5 ENVIRONMENTAL CONDITIONS..............................................................................................................................7 3.6 SUMMARY OF TEST RESULTS/PLOTS......................................................................................................................7 3.7 CONDUCTED EMISSIONS TEST DATA......................................................................................................................7 4. §15.203 - ANTENNA REQUIREMENT................................................................................................................10 4.1 STANDARD APPLICABLE.......................................................................................................................................10 4.2 TEST RESULT........................................................................................................................................................10 5. POWER SPECTRAL DENSITY ...........................................................................................................................11 5.1 STANDARD APPLICABLE.......................................................................................................................................11 5.2 TEST EQUIPMENT LIST AND DETAILS...................................................................................................................11 5.3 TEST PROCEDURE.................................................................................................................................................11 5.4 ENVIRONMENTAL CONDITIONS............................................................................................................................11 5.5 SUMMARY OF TEST RESULTS/PLOTS....................................................................................................................12 6. 6-DB BANDWIDTH ................................................................................................................................................16 6.1 STANDARD APPLICABLE.......................................................................................................................................16 6.2 TEST EQUIPMENT LIST AND DETAILS...................................................................................................................16 6.3 TEST PROCEDURE.................................................................................................................................................16 6.4 ENVIRONMENTAL CONDITIONS............................................................................................................................16 6.5 SUMMARY OF TEST RESULTS/PLOTS.......…

Text truncated - open the document above for the full version.

Pismolabs Technology Limited Model: Pismo 525 REPORT NO.: STR11048093I PAGE 1 OF 49 FCC PART 15.247 FCC Part 15C Measurement and Test Report For Pismolabs Technology Limited Room 1703A, 17/F, Park Building, 476 Castle Peak Road, Cheung Sha Wan, Kowloon, HongKong FCC ID: U8G-P1625 Report Concerns: Original Report Equipment Type: Pepwave Wireless Product Model: Pismo 525 Report No.: STR11048093I Test Date: 2011-04-08 to 2011-05-17 Issue Date: 2011-05-31 Tested By: Galy He / Engineer Reviewed By: Lahm Peng / EMC Manager Approved & Authorized By: Jandy so / PSQ Manager Prepared By: SEM.Test Compliance Service Co., Ltd 3/F, Jinbao Commerce Building, Xin'an Fanshen Road, Bao'an District, Shenzhen, P.R.C.（518101） Tel.: +86-755-33663308 Fax.: +86-755-33663309 Website: www.semtest.com.cn Note: This test report is limited to the above client company and the product model only. It may not be duplicated without prior permitted by SEM.Test Compliance Service Co., Ltd . Pismolabs Technology Limited Model: Pismo 525 REPORT NO.: STR11048093I PAGE 2 OF 49 FCC PART 15.247 TABLE OF CONTENTS 1. GENERAL INFORMATION ...................................................................................................................................3 1.1 PRODUCT DESCRIPTION FOR EQUIPMENT UNDER TEST (EUT).........................................…

Text truncated - open the document above for the full version.