U8G-SF400BGPePWave Surf AP400, PePWave Surf 400

PePLink Surf User’s Manual Document Version : 2.6 Firmware Version : 6.0.4 Date : 2006-02-10 PePLink Surf User’s Manual v2.6 Copyright © 1999-2006 PePLink Ltd. All Rights Reserved Page 2 of 32 Table of Content 1 Copyright 3 2 Disclaimer 3 3 Product Description 4 3.1 Features 4 3.2 Hardware Setup 5 3.3 LED Description 6 4 Using the PePLink Surf 9 4.1 First Time Setup 10 4.2 Settings Details 13 4.3 Advanced Settings: Port Forward 15 4.4 WPA/WPA2 with 802.1x Authentication 16 4.5 Test the Setup 19 4.6 Firmware Upgrade 20 4.7 Debug Page 21 4.8 Restore to Factory Defaults 22 4.9 System Settings 23 5 Appendix - Demo CA and Server Certification Generation Instructions 28 5.1 Prerequisite 28 5.2 Create your own Certificate Authority (CA) 28 5.3 Create a server certificate request from your servers 29 5.4 Sign the server certificate with your own CA 31 PePLink Surf User’s Manual v2.6 Copyright © 1999-2006 PePLink Ltd. All Rights Reserved Page 3 of 32 1 Copyright Copyright © 2006 by PePLink Ltd. The content of this documentation may not be reproduced in any part or as a whole without the prior written permission of PePLink Ltd. 2 Disclaimer PePLink does not assume any liability arising out of the application or use of any products, or software described herein. Neither does it convey any license under its patent right nor the patent rights of others. PePLink further reserves the right to make changes in any products described herein without notice. This documentation is subject to change without notice. PePLink Surf User’s Manual v2.6 Copyright © 1999-2006 PePLink Ltd. All Rights Reserved Page 4 of 32 3 Product Description PePLink Surf, formerly known as MANGA Surf, is a Wi-Fi Station Mode (Client) Router with WPA, WPA2 and 802.1x supplicant support. It is designed to act as a Wireless router which connects to Wireless Broadband Internet Service and allows LAN users to access the Internet via it. It associates to a service provider and authenticates using 802.1x (if needed) on start up. Upon successful association and authentication, it will acquire an IP address from the service provider using DHCP. A DHCP server is built-in on its LAN port. Network Address Translation is performed for all outbound connections. Thus it supports multiple terminals to access the Internet simultaneously. 3.1 Features • 10/100 Ethernet interface with auto-crossover detection • Reset button for restoring settings to factory defaults • Signal strength LED for showing the current signal strength • WPA/WPA2-Personal and WPA/WPA2-Enterprise support • Network Address Translation (NAT) routing • Built-in DHCP server • Inbound port range forwarding PePLink Surf User’s Manual v2.6 Copyright © 1999-2006 PePLink Ltd. All Rights Reserved Page 5 of 32 3.2 Hardware Setup 1. Attach the provided antenna to the left most antenna connector 2. Connect the LAN port to the computer’s Ethernet port with an Ethernet cable. 3. Connect the end of the included power adapter to the power socket (labeled “DC 5V”) on PePLink Surf. 4. Power on the power adaptor. PePLink Surf User’s Manual v2.6 Copyright © 1999-2006 PePLink Ltd. All Rights Reserved Page 6 of 32 3.3 LED Description L E D C o l o r S t a t u s Description G r e e n O n Power is on P o w e r O f f Power is off G r e e n S o l i d Received signal is Excellent, Very Good and Good S t a t u sG r e e n B l i n k i n g Received signal is Low PePLink Surf User’s Manual v2.6 Copyright © 1999-2006 PePLink Ltd. All Rights Reserved Page 7 of 32 A m b e r B l i n k i n g Received signal is Very Low A m b e r S o l i d No wireless signal is detected O f f Booting up / Upgrading firmware G r e e n O n Ethernet is connected G r e e n B l i n k i n g Sending/Receiving data L A N O f f Ethernet is not connected W i - F i G r e e n O n Associated with an access point PePLink Surf User’s Manual v2.6 Copyright © 1999-2006 PePLink Ltd. All Rights Reserved Page 8 of 32 G r e e n B l i n k i n g Sending/Receiving data O f f Not associated with any access point This is the Signal Strength and Status LED state conversion table. Received Signal Strength Status LED Indication on the web based power meter > -70 Solid Green Excellent -70 to -74 Solid Green Very good -75 to -79 Solid Green Good -80 to -84 Blinking Green Low -85 to -87 Blinking Amber Very Low -87 to -89 Blinking Amber Very Low -89 < Blinking Amber Very Low PePLink Surf User’s Manual v2.6 Copyright © 1999-2006 PePLink Ltd. All Rights Reserved Page 9 of 32 4 Using the PePLink Surf You should set up your computer’s LAN interface to obtain an IP address automatically. If you do so, you should have set it up correctly. In order to do so, select the “Start” menu, “Control Panel” and then “Network Connections”. Right click on the “Local Area Connection” icon, choose “Properties”, double click on the item “Internet Protocol (TCP/IP)” from the list. On the screen, just set it as follows: Click the “OK” button to confirm the change. PePLink Surf User’s Manual v2.6 Copyright © 1999-2006 PePLink Ltd. All Rights Reserved Page 10 of 32 4.1 First Time Setup On your PC, start a web browser, e.g. Internet Explorer, Mozilla Firefox, etc. Visit an Internet web site. If you are not associated to an access point, you should be redirected to a logon page. Or you can go also go to this URL http://192.168.20.1/ The page will look like this. Once it is associated to an access point, you can also access the page from this URL: https://wan.ip.addr.here:8000/ Login ID and password are “admin” and “MSurf000”. PePLink Surf User’s Manual v2.6 Copyright © 1999-2006 PePLink Ltd. All Rights Reserved Page 11 of 32 Click the “Advanced Config” button to enter the parameters of the access point to associate to. You should see this screen: In the field “SSID” under Wireless Settings, input the access point’s SSID (sometimes it is called “network name”). According to the setting of the Access Point you are associating to, you may choose different “Authentication setting”. If “Static WE…

Text truncated - open the document above for the full version.

Page 1 CONSTRUCTION PHOTOS OF EUT

FCC ID: U8G-SF400BG FCC LABEL LOCATION The label will be permanently affixed at a conspicuous location on the device. Label

Page 2 Page 3 Page 4 Page 5 Page 6 Page 7 Page 8 Page 9 Page 10 Page 11

Report No.: SA960502H03 1 RF EXPOSURE REPORT REPORT NO.: SA960502H03 MODEL NO.: PePWave Surf AP400, PePWave Surf 400 FCC ID: U8G-SF400BG ACCORDING: FCC Guidelines for Human Exposure IEEE C95.1 APPLICANT: Pismo Labs Technology Limited ADDRESS: Room 1703A, 17/F, Park Building,476 Castle Peak Road, Cheung Sha Wan, Kowloon, Hong Kong ISSUED BY: Advance Data Technology Corporation LAB LOCATION: No. 81-1, Lu Liao Keng, 9 Ling, Wu Lung Tsuen, Chiung Lin Hsiang, Hsin Chu Hsien, Taiwan, R.O.C. Report No.: SA960502H03 2 RF Exposure Measurement 1. Introduction In this document, we try to prove the safety of radiation harmfulness to the human body for our product. The limit for Maximum Permissible Exposure (MPE) specified in FCC 1.1310 is followed. The Gain of the antenna used in this product is measured in a Fully Anechoic Chamber (FAC) calibrated for antenna measurement in ADT, and also the maximum total power input to the antenna is measured. Through the Friis transmission formula and the maximum gain of the antenna, we can calculate the distance, away from the product, where the limit of MPE is reached. Although the Friis transmission formula is a far field assumption, the calculated result of that is an over-prediction for near field power density. We will take that as the worst case to specify the safety range. 2. RF Exposure Limit According to FCC 1.1310: The criteria listed in the following table shall be used to evaluate the environmental impact of human exposure to radio-frequency (RF) radiation as specified in 1.1307(b) LIMITS FOR MAXIMUM PERMISSIBLE EXPOSURE (MPE) Frequency Range (MHz) Electric Field Strength (V/m) Magnetic Field Strength (A/m) Power Density (mW/cm 2 ) Average Time (minutes) (A)Limits For Occupational / Control Exposures 300-1500 ... ... F/300 6 1500-100,000 ... ... 5 6 (B)Limits For General Population / Uncontrolled Exposure 300-1500 ... ... F/1500 6 1500-100,000 ... ... 1.0 30 F = Frequency in MHz Report No.: SA960502H03 3 3. Friis Formula Friis transmission formula : Pd = (Pout*G) / (4*pi*r 2 ) where Pd = power density in mW/cm 2 Pout = output power to antenna in mW G = gain of antenna in linear scale Pi = 3.1416 R = distance between observation point and center of the radiator in cm Pd is the limit of MPE, 1 mW/cm 2 . If we know the maximum Gain of the antenna and the total power input to the antenna, through the calculation, we will know the MPE value at distance 20cm. Ref. : David K. Cheng, Field and Wave Electromagnetics, Second Edition, Page 640, Eq. (11-133). 4. EUT Operating condition The software provided by Manufacturer enabled the EUT to transmit and receive data at lowest, middle and highest channel individually. 5. Classification The antenna of this product, under normal use condition, is at least 20cm away from the body of the user. Warning statement to the user for keeping at least 20cm or more separation distance with the antenna should be included in users manual. So, this device is classified as Mobile Device Report No.: SA960502H03 4 6. Test Results 6.1 Antenna Gain The maximum Gain measured in Fully Anechoic Chamber is 5dBi or 3.162278 (numeric) 6.2 Output Power Into Antenna & RF Exposure value at distance 20cm: For Part 802.11b: Channel Channel Frequency (MHz) Output Power to Antenna (mW) Power Density (mW/cm 2 ) Limit of Power Density (mW/cm 2 ) 1 2412 426.580 0.268 1.0 6 2437 389.045 0.245 1.0 11 2462 354.813 0.223 1.0 For Part 802.11g: Channel Channel Frequency (MHz) Output Power to Antenna (mW) Power Density (mW/cm 2 ) Limit of Power Density (mW/cm 2 ) 1 2412 676.083 0.425 1.0 6 2437 645.654 0.406 1.0 11 2462 707.946 0.445 1.0

Report No.: RF960502H03 1 Report Format Version 2.0.5 FCC TEST REPORT REPORT NO.: RF960502H03 MODEL NO.: PePWave Surf AP400, PePWave Surf 400 RECEIVED: May 02, 2007 TESTED: May 02 to 08, 2007 ISSUED: May 29, 2007 APPLICANT: Pismo Labs Technology Limited ADDRESS: Room 1703A, 17/F, Park Building,476 Castle Peak Road, Cheung Sha Wan, Kowloon, Hong Kong ISSUED BY: Advance Data Technology Corporation LAB LOCATION: No. 81-1, Lu Liao Keng, 9 Ling, Wu Lung Tsuen, Chiung Lin Hsiang, Hsin Chu Hsien, Taiwan, R.O.C. This test report consists of 65 pages in total. It may be duplicated completely for legal use with the approval of the applicant. It should not be reproduced except in full, without the written approval of our laboratory. The client should not use it to claim product endorsement by CNLA, A2LA or any government agencies. The test results in the report only apply to the tested sample. No. 2177-01 Report No.: RF960502H03 2 Report Format Version 2.0.5 Table of Contents 1 CERTIFICATION..........................................................................................4 2 SUMMARY OF TEST RESULTS..................................................................5 3 GENERAL INFORMATION...........................................................................6 3.1 GENERAL DESCRIPTION OF EUT.............................................................6 3.2 DESCRIPTION OF TEST MODES...............................................................7 3.3 TEST MODE APPLICABLITY AND TESTED CHANNEL DETAIL:................8 3.4 GENERAL DESCRIPTION OF APPLIED STANDARDS.............................10 3.5 DESCRIPTION OF SUPPORT UNITS........................................................11 3.6 CONFIGURATION OF SYSTEM UNDER TEST.........................................12 4 TEST TYPES AND RESULTS....................................................................13 4.1 CONDUCTED EMISSION MEASUREMENT..............................................13 4.1.1 LIMITS OF CONDUCTED EMISSION MEASUREMENT...........................13 4.1.2 TEST INSTRUMENTS...............................................................................13 4.1.3 TEST PROCEDURES................................................................................14 4.1.4 TEST SETUP.............................................................................................14 4.1.5 EUT OPERATING CONDITIONS...............................................................15 4.1.6 TEST RESULTS.........................................................................................16 4.2 RADIATED EMISSION MEASUREMENT...................................................18 4.2.1 LIMITS OF RADIATED EMISSION MEASUREMENT................................18 4.2.2 TEST INSTRUMENTS...............................................................................19 4.2.3 TEST PROCEDURES................................................................................20 4.2.4 TEST SETUP.............................................................................................21 4.2.5 EUT OPERATING CONDITIONS...............................................................21 4.2.6 TEST RESULTS.........................................................................................22 4.2.7 TEST RESULTS - DSSS............................................................................23 4.2.8 TEST RESULTS - OFDM...........................................................................30 4.3 6dB BANDWIDTH MEASUREMENT..........................................................37 4.3.1 LIMITS OF 6dB BANDWIDTH MEASUREMENT.......................................37 4.3.2 TEST INSTRUMENTS...............................................................................37 4.3.3 TEST PROCEDURE..................................................................................38 4.3.4 TEST SETUP.............................................................................................38 4.3.5 EUT OPERATING CONDITIONS...............................................................38 4.3.6 TEST RESULTS –DSSS............................................................................39 4.3.7 TEST RESULTS-OFDM.............................................................................42 4.4 MAXIMUM PEAK OUTPUT POWER..........................................................45 4.4.1 LIMITS OF MAXIMUM PEAK OUTPUT POWER MEASUREMENT...........45 4.4.2 TEST INSTRUMENTS...............................................................................45 4.4.3 TEST PROCEDURES................................................................................46 4.4.4 TEST SETUP.............................................................................................46 Report No.: RF960502H03 3 Report Format Version 2.0.5 4.4.5 EUT OPERATING CONDITIONS...............................................................46 4.4.6 TEST RESULTS – DSSS...........................................................................47 4.4.7 TEST RESULTS –OFDM...........................................................................48 4.5 POWER SPECTRAL DENSITY MEASUREMENT.....................................49 4.5.1 LIMITS OF POWER SPECTRAL DENSITY MEASUREMENT...................49 4.5.2 TEST INSTRUMENTS...............................................................................49 4.5.3 TEST PROCEDURE..................................................................................50 4.5.4 TEST SETUP.............................................................................................50 4.5.5 EUT OPERATING CONDITIONS...............................................................50 4.5.6 TEST RESULTS –DSSS............................................................................51 4.5.7 TEST RESULTS –OFDM...........................................................................54 4.6 CONDUCTED EMISSION AND BAND EDGES MEASUREMENT.............57 4.6.1 LIMITS OF condtcted emission and BAND EDGES MEASUREMENT.......57…

Text truncated - open the document above for the full version.

1 PHOTOGRAPHS OF THE TEST CONFIGURATION CONDUCTED EMISSION TEST 2 RADIATED EMISSION TEST 1 PHOTOGRAPHS OF THE TEST CONFIGURATION CONDUCTED EMISSION TEST 2 RADIATED EMISSION TEST