UP3PC6PayClock Terminal

5015 B.U. Bowman Drive Buford, GA 30518 USA Voice: 770-831-8048 Fax: 770-831-8598 Certification Exhibit FCC ID: UP3PC6 IC: 2852A-PC6 FCC Rule Part: 15.209 IC Radio Standards Specification: RSS-210 ACS Report Number: 10-0162.W06.11.A Manufacturer: Lathem Time Corp. Model: PC600 Manual PayClock ® Touch Time and Attendance System Model PC600 User’s Guide THIS EQUIPMENT COMPLIES WITH FCC REQUIREMENTS PURSUANT TO PART-15 “NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. “ This Class A digital apparatus meets all requirements of the Canadian Interference Causing Equipment Regulations. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Cet appareillage numérique de la classe A répond à toutes les exigences de l'interférence canadienne causant des règlements d'équipement. L'opération est sujette aux deux conditions suivantes: (1) ce dispositif peut ne pas causer l'interférence nocive, et (2) ce dispositif doit accepter n'importe quelle interférence reçue, y compris l'interférence qui peut causer l'opération peu désirée. Warning: Changes or modifications to this device not expressly approved by Lathem Time Corporation could void the user’s authority to operate the equipment. Lathem Time Corporation 200 Selig Drive, SW Atlanta, Georgia USA 30336 (800) 241-4990 (404) 691-0400 www.lathem.com 06-02-2010 P/N: USG0092-Draft 3 CONTENTS QUICK START STEPS .................................................................................. IV WELCOME ........................................................................................................ 1 PACKAGE CONTENTS ................................................................................... 5 SYSTEM REQUIREMENTS ........................................................................... 6 INSTALL THE PC600 ...................................................................................... 7 INSTALL THE PAYCLOCK SOFTWARE ......................................................... 9 OPEN PAYCLOCK......................................................................................... 11 CONFIGURE PAYCLOCK ........................................................................... 14 ADD EMPLOYEES AND ASSIGN BADGES .............................................. 15 UPDATING THE TERMINAL ...................................................................... 18 USING THE PC600 TERMINAL .................................................................. 19 NAVIGATING PAYCLOCK ......................................................................... 33 TIMECARD TAB ............................................................................................ 35 SCHEDULING TAB ....................................................................................... 38 REPORTS TAB ............................................................................................... 40 TERMINAL MANAGER TAB ...................................................................... 41 SETUP TAB ..................................................................................................... 46 GENERAL TROUBLESHOOTING .............................................................. 49 HARDWARE TROUBLESHOOTING ......................................................... 50 SOFTWARE TROUBLESHOOTING........................................................... 51 Copyright © 2010 Lathem Time Corporation. All rights reserved. Reproduction of this document in whole or in part is strictly prohibited. This document may contain typographical or copy errors. PayClock, Lathem, the Lathem logo, and all other Lathem product names mentioned in this document are registered trademarks of Lathem Time Corporation. All other products, brand names, or company names mentioned in this document are properties and trademarks or registered trademarks of their respective companies. Quick Start Steps Carefully follow each step of these instructions for a trouble-free experience. 1 2 3 Select a location that will be convenient to employees punching In/Out. Also keep in mind that a 115vAC power outlet should be within 6 feet as well as a connection to the network (LAN). Note: It is recommended to install and mount the PC600 terminal before installing the PayClock software. With the PC600 terminal powered up and connected to the network (LAN), the software will search for it on the network and automatically configure the communications to the terminal. Verify the contents of your system (For more detailed information turn to page 6.) Use masking tape to hold the included mounting template onto the wall. Drill the holes using the template as a guide. Note: The bottom of the terminal should be about 45 inches from the floor. Remove the template and install the mounting screws, using the plastic wall anchors if needed. Leaving about 3/16” of the screw exposed. 4 5 6 7 Plug the RJ45 network cable into the Ethernet port and the Power Adapter plug into the Power Adapter port which is located in the compartment on back of the terminal. Route the cabling through the available channels to best suit your installation. Hang the terminal on the wall, aligning the three keyholes on the rear of the terminal with the protruding screw heads, an…

Text truncated - open the document above for the full version.

5015 B. U. Bowman Dr. Buford, GA 30518 June 3, 2010 ACS TCB 5015 B.U. Bowman Drive Buford, GA 30518 Re: FCC ID: UP3PC6 To Whom It May Concern: The following application is submitted on behalf of our client, Lathem Time Corp., for evaluation of their model PC600 for certification under FCC Part 15.209. Sincerely, Sam Wismer Vice President, Technology Advanced Compliance Solutions, Inc.

200 Selig Drive S.W. LATHEM TIME CORPORATION Atlanta, Georgia USA 30336-2033 Tel: 404.691.0400 FAX: 404.696.6048 www.Lathem.com TIME CLOCKS * TIME STAMPS * AUTOMATED TIME SYSTEMS * MASTER CONTROL SYSTEMS * WALL CLOCKS May 12, 2010 Federal Communications Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MD 21046 Dear Sir or Madam: I hereby appoint Sam Wismer at Advanced Compliance Solutions, Inc. to act as our agent in the preparation of an application for equipment authorization of FCC ID: UP3PC6 to the FCC Rules and Regulations. I certify that all exhibits contained within this filing properly describe the device or system for which authorization is sought. I further certify that appropriate arrangements have been made to assure that production units of this equipment bearing the name and FCC IDENTIFIER listed in this application will continue to comply with the Commission's requirements. I further certify by signature below that no party (per 47 CFR 1.2002(b)) to the application is subject to a denial of Federal benefits, including FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). This appointment also includes the authority to complete FCC Form 731 on our behalf and sign the application as an authorized agent. Sincerely, Ellery W. Potash Sr. Engineer

200 Selig Drive S.W. LATHEM TIME CORPORATION Atlanta, Georgia USA 30336-2033 Tel: 404.691.0400 FAX: 404.696.6048 www.Lathem.com TIME CLOCKS * TIME STAMPS * AUTOMATED TIME SYSTEMS * MASTER CONTROL SYSTEMS * WALL CLOCKS May 12, 2010 CONFIDENTIALITY REQUEST Federal Communications Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MD 21046 Gentlemen: Lathem Time Corp. respectfully requests confidentiality of certain materials provided with the submission of the PC600 Data Collection Terminal under FCC ID: UP3PC6 in accordance with FCC Regulations 0.459. The confidentiality request applies to the (1) schematic diagrams, (2) detailed block diagrams, and (3) detailed operational descriptions contained in this filing and included in the following files. 10-0162 – Schematics.pdf 10-0162 – System Block Diagram.pdf 10-0162 – Theory of Operation.pdf The PC600 Data Collection Terminal has been developed at considerable effort and expense by Lathem Time Corp. These items are considered as Trade Secrets and therefore public access to the proprietary material could possibly result in duplication of equipment that could severely damage the company's business advantage. I appreciate your assistance in this matter. Sincerely, Ellery W. Potash Sr.Engineer May 12, 2010

5015 B.U. Bowman Drive Buford, GA 30518 USA Voice: 770-831-8048 Fax: 770-831-8598 Certification Exhibit FCC ID: UP3PC6 IC: 2852A-PC6 FCC Rule Part: 15.209 IC Radio Standards Specification: RSS-210 ACS Report Number: 10-0162.W06.11.A Manufacturer: Lathem Time Corp. Model: PC600 External Photos Model(s): PC600 FCC ID: UP3PC6 IC: 2852A-PC6 Figure 1: Front view ACS Report: 10-0162.W06.11.A Advanced Compliance Solutions Page 2 Model(s): PC600 FCC ID: UP3PC6 IC: 2852A-PC6 Figure 2: Back View ACS Report: 10-0162.W06.11.A Advanced Compliance Solutions Page 3 Model(s): PC600 FCC ID: UP3PC6 IC: 2852A-PC6 Figure 3: Top View ACS Report: 10-0162.W06.11.A Advanced Compliance Solutions Page 4 Model(s): PC600 FCC ID: UP3PC6 IC: 2852A-PC6 Figure 4: Bottom View ACS Report: 10-0162.W06.11.A Advanced Compliance Solutions Page 5 Model(s): PC600 FCC ID: UP3PC6 IC: 2852A-PC6 Figure 5: Side View ACS Report: 10-0162.W06.11.A Advanced Compliance Solutions Page 6 Model(s): PC600 FCC ID: UP3PC6 IC: 2852A-PC6 ACS Report: 10-0162.W06.11.A Advanced Compliance Solutions Page 7 Figure 6: Side 2 View

5015 B.U. Bowman Drive Buford, GA 30518 USA Voice: 770-831-8048 Fax: 770-831-8598 Certification Exhibit FCC ID: UP3PC6 IC: 2852A-PC6 FCC Rule Part: 15.209 IC Radio Standards Specification: RSS-210 ACS Report Number: 10-0162.W06.11.A Manufacturer: Lathem Time Corp. Model: PC600 Label Information

5015 B.U. Bowman Drive Buford, GA 30518 USA Voice: 770-831-8048 Fax: 770-831-8598 Certification Exhibit FCC ID: UP3PC6 IC: 2852A-PC6 FCC Rule Part: 15.209 IC Radio Standards Specification: RSS-210 ACS Report Number: 10-0162.W06.11.A Manufacturer: Lathem Time Corp. Model: PC600 Internal Photos Model(s): PC600 FCC ID: UP3PC6 IC: 2852A-PC6 Figure 1: PCB without Shields - Front ACS Report: 10-0162.W06.11.A Advanced Compliance Solutions Page 2 Model(s): PC600 FCC ID: UP3PC6 IC: 2852A-PC6 ACS Report: 10-0162.W06.11.A Advanced Compliance Solutions Page 3 Figure 2: PCB - Back

5015 B.U. Bowman Drive Buford, GA 30518 USA Voice: 770-831-8048 Fax: 770-831-8598 Certification Test Report FCC ID: UP3PC6 IC: 2852A-PC6 FCC Rule Part: 15.209 IC Radio Standards Specification: RSS-210 ACS Report Number: 10-0162.W06.11.A Manufacturer: Lathem Time Corp. Model: PC600 Test Begin Date: May 12, 2010 Test End Date: July 16, 2010 Report Issue Date: July 16, 2010 FOR THE SCOPE OF ACCREDITATION UNDER LAB Code 200612-0 This report must not be used by the client to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the Federal Government. Reviewed by: Kirby Munroe Director, Wireless Certifications ACS, Inc. This test report shall not be reproduced except in full. This report may be reproduced in part with prior written consent of ACS, Inc. The results contained in this report are representative of the sample(s) submitted for evaluation. This report contains 16 pages 5015 B.U. Bowman Drive Buford, GA 30518 USA Voice: 770-831-8048 Fax: 770-831-8598 TABLE OF CONTENTS 1 GENERAL ............................................................................................................................................ 3 1.1 PURPOSE .......................................................................................................................................... 3 1.2 PRODUCT DESCRIPTION ................................................................................................................... 3 1.3 TEST METHODOLOGY AND CONSIDERATIONS ................................................................................. 3 2 TEST FACILITIES .............................................................................................................................. 4 2.1 LOCATION ....................................................................................................................................... 4 2.2 LABORATORY ACCREDITATIONS/RECOGNITIONS/CERTIFICATIONS ................................................ 4 2.3 RADIATED EMISSIONS TEST SITE DESCRIPTION .............................................................................. 5 2.3.1 Semi-Anechoic Chamber Test Site .......................................................................................... 5 2.3.2 Open Area Tests Site (OATS) ................................................................................................. 6 2.4 CONDUCTED EMISSIONS TEST SITE DESCRIPTION ........................................................................... 7 3 APPLICABLE STANDARD REFERENCES .................................................................................... 7 4 LIST OF TEST EQUIPMENT ............................................................................................................ 8 5 SUPPORT EQUIPMENT .................................................................................................................... 9 6 EQUIPMENT UNDER TEST SETUP BLOCK DIAGRAM ........................................................... 9 7 SUMMARY OF TESTS ..................................................................................................................... 10 7.1 ANTENNA REQUIREMENT – FCC: SECTION 15.203 ....................................................................... 10 7.2 POWER LINE CONDUCTED EMISSIONS – FCC: SECTION 15.207 IC: RSS-GEN 7.2.2 ...................... 10 7.2.1 Measurement Procedure ....................................................................................................... 10 7.2.2 Measurement Results ............................................................................................................ 10 7.3 RADIATED EMISSIONS – FCC CFR 47 PART 15.209 / RSS-210 SECTION 2.6................................. 12 7.3.1 Measurement Procedure ....................................................................................................... 12 7.3.2 Distance Correction for Measurements Below 30 MHz – Part 15.31 .................................. 12 7.3.3 Measurement Results ............................................................................................................ 13 7.3.4 Sample Calculation ............................................................................................................... 13 7.4 20DB / 99% BANDWIDTH – FCC: SECTION 15.215(C) / IC: RSS-210 SECTION 4.6.1 ..................... 14 7.4.1 Measurement Procedure ....................................................................................................... 14 7.4.2 Measurement Results ............................................................................................................ 14 7.5 RADIATED EMISSIONS – FCC: SECTION 15.109(UNINTENTIONAL RADIATION) IC: RSS-210 2.6 .. 16 7.5.1 Measurement Procedure ....................................................................................................... 16 7.5.2 Measurement Results ............................................................................................................ 16 8 CONCLUSION ................................................................................................................................... 16 Model: PC600 FCC ID: UP3PC6 IC: 2852A-PC6 ACS Report: 10-0162.W06.11.A Advanced Compliance Solutions Page 3 1 GENERAL 1.1 Purpose The purpose of this report is to demonstrate compliance with Part 15 Subpart C of the FCC’s Code of Federal Regulations and Industry Canada’s Radio Standards Specification RSS-210. 1.2 Product description The PC600 is a Data Collection Terminal to be used in Time & Attendance applications. It is enclosed in ABS Plastic and powered by an external Power Adapter that converts 115vAC Input to low-voltage 12vDC for the Terminal. It is based upon ARM9 processor architecture and its application firmware runs on the Win-CE Operating System. Technical Details: Frequency Range: 125 kHz Operating channels: 1 Modulation: OOK Operating Voltage: 12 VDC Manufacturer Information: Lathem Time Corporation 200 Selig…

Text truncated - open the document above for the full version.

5015 B.U. Bowman Drive Buford, GA 30518 USA Voice: 770-831-8048 Fax: 770-831-8598 Certification Exhibit FCC ID: UP3PC6 IC: 2852A-PC6 FCC Rule Part: 15.209 IC Radio Standards Specification: RSS-210 ACS Report Number: 10-0162.W06.11.A Manufacturer: Lathem Time Corp. Model: PC600 Test Setup Photos Model(s): PC600 FCC ID: UP3PC6 IC: 2852A-PC6 Figure 1: Intentional Radiated Emissions below 30 MHz ACS Report: 10-0162.W06.11.A Advanced Compliance Solutions Page 2 Model(s): PC600 FCC ID: UP3PC6 IC: 2852A-PC6 Figure 2: Unintentional Radiated Emissions – 30 MHz – 1 GHz ACS Report: 10-0162.W06.11.A Advanced Compliance Solutions Page 3 Model(s): PC600 FCC ID: UP3PC6 IC: 2852A-PC6 Figure 3: Unintentional Radiated Emissions – 30 MHz – 1 GHz ACS Report: 10-0162.W06.11.A Advanced Compliance Solutions Page 4 Model(s): PC600 FCC ID: UP3PC6 IC: 2852A-PC6 Figure 4: Conducted Emissions ACS Report: 10-0162.W06.11.A Advanced Compliance Solutions Page 5 Model(s): PC600 FCC ID: UP3PC6 IC: 2852A-PC6 ACS Report: 10-0162.W06.11.A Advanced Compliance Solutions Page 6 Figure 5: Conducted Emissions