UP5-SC-BT6800TPMS for iPod,iPhone,iPad

Copyright (C) ATBS Technology Co. R1 版權所有請勿翻印 iTPMSystem for iPod, iPhone, iPad User’s Guide 1. Introduction This Tire Pressure Monitoring System (TPMS) was designed for increasing security, reliability, and understanding on tire conditions of your car. Once you properly install the TPMS, these sensors will automatically monitor pressures and temperatures of tires in real time, and send these data to Receiver through Bluetooth communications. When any abnormal pressure (under or over inflated) and/or temperature of tire is detected, iPhone, iPod, and iPad will alert driver by its LED warning signal and sound alarm immediately. This system could ensure you are driving in safety. About This Manual  The information in this manual is subject to change without notice.  This manual has been created with carefulness. In case that you have any comments or questions regarding this manual, please contact your local dealer or our Customer Service Center.  Before operating this set, please fully understand the prerequisite such as specifications or constraints of the hardware and software. We are not responsible and have no liability for any loss, damage or injury as a result of misuse. 2. Check Accessories BT6800 (AT67) BT6800 (MS30) receiver 1 1 AT 67 sensor 4 0 AT67 battery 4 0 Lock nut 4 0 Rubber gasket 4 0 Wrench 1 0 MS30 sensor 0 4 MS30 accessories 0 4 User guide 1 1 Power adaptor (12V to 5V) 1 1 3. System Installation 3.1 Install Receiver ： 3.1.1 Plug in power adaptor. 3.1.2 Plug USB connector into power adaptor. 3.1.3 Receiver will display Blue LED to each wheel position. The LED blue light of receiver will light up once it gets the sensor’s signal. 3.1.4 However, if L2 wheel is abnormal, the L2 blue light will flash and the yellow warning signal in the middle will light up. (1) If the tire pressure is too low: it’ll alert with a short sound. (2) If the tire pressure is too high: it’ll alert with a long sound and a short sound. (3) If the tire temperature is too high: it’ll alert with continuous long sound. 3.1.5 And if the receiver can’t get the signal from R1 sensor, the LED blue light of R1 will go out, then please check as follows: (1) replace the sensor’s battery. (2) go to App to confirm whether the ID position is correct. Copyright (C) ATBS Technology Co. R1 版權所有請勿翻印 (3) to check whether the installation is correct. Note: The mini USB socket in the back is for power only, there’s no data communication function. 3.2 Install A-Type External Sensor (Battery replaceable): 3.2.1 Each sensor’s label has been marked its ID and its wheel order. EX: Sensor’s Model. No.: AT67 Wheel Order: 01:L1 ID: 3C0886B5 3.2.2 Place the battery into the sensor and screw the top cap onto the sensor. Please follow the battery’s polarity to place the battery. Upside is +, downside is -. 3.2.2 Remove the original valve cap from the tire. 3.2.3 Screw lock nut first (1) and will become (2). Screw the sensor onto valve stem clockwise (3). Screw (1) lock nut back and use the wrench to lock tightly (4). (3)(4) steps can make sure the sensor’s fixity and is provided with anti-theft function. Note： (1) Beware of the conductivity between the sensor and the valve stem. (2) Sensors are supposed to be well locked onto the valve stem to avoid from leaking. (3) Please replace sensor’s battery once its voltage is under 2.6v. (4) If driver drives on a lumpy road, or the tire pressure changes rapidly, our device will deem this as a danger situation, and the device will alert the driver continuously by sending 10 data, in this condition, the battery will ran out fast. 3.3 Install M-Type Internal Sensor : 3.3.1 Each sensor’s label has been marked its ID and its wheel order. 3.3.2 Tire location 3.4 Install Internal Sensor (M-type) 3.4.1 Remove the tires from vehicles. 3.4.2 Deflate the tires and detach rim and tire. 3.4.3 Install sensor on rim to appropriate position. 3.4.4 Balance wheels. 3.4.5 Install wheel to appropriate position. 4. iTPMS APP Installation: iTPMS App is for free. Through the App, you can know tire temperature and pressure, battery voltage of each sensor, and each sensor’s ID. 01: Left Front (L1) 02: Right Front (R1) 04: Left Rear (L2) 03: Right Rear (R2) Model Copyright (C) ATBS Technology Co. R1 版權所有請勿翻印 4.1 Install App 4.1-1 Download the APP: iTPMS from Apple Store/ Google Play. 4.1-2 Go to Setting  General  Bluetooth Page. 4.1-3 Turn on the Bluetooth, and search the device. 4.1-4 Find iTPMS device and pair with it. The name of device is BT6800 XXXXXX (X=0-9) 4.1-5 Click Allow to start iTPMS APP. 4.1-5 Choose the vehicle and then user is allowed to read tire condition from the App. Note: Four sensors was set by the manufacturer, there’s no need to pair the sensors again. (If there are requests to change new sensors or to change the wheel order please follow the instruction: sensor ID learning.) 4.2 iTPMSystem alert and setting instruction: 4.2-1 Enter Setup page, users can set up the unit and limit of tire pressure and temperature. Go back to main page to save the setting. After finishing the setting and go back to main page, the receiver will flash 1 time, it means the setting is already saved into the receiver. When downloading a new iTPMS, make sure to set up the unit, tire pressure and tire temperature limit, and go back to main page and save it. 4.2-2 iTPMSystem App alert description: Go to the setting page and users are allowed to set tire pressure and temperature limit. (Please refer to the vehicle’s tire pressure label, we suggest to set the lower limit to 80% of the normal value.) Tire pressure is too high and it’s over the limit. No pressure. Tire pressure is too low and it’s under the limit. Tire temperature is over the limit. Sensor’s battery voltage is too low. Tire condition is abnormal. Copyright (C) ATBS Technology Co. R1 版權所有請勿翻印 4.3 Reset Sensor’s ID 4.3.1 Method 1: External type: intall the sensor from the left front tire. Internal type: First, deflate all tire pressure to 15psi, then …

Text truncated - open the document above for the full version.

CERPASS TECHNOLOGY CORP. Report No.: TEMJ1211033 Cerpass Technology Corp. Issued Date : Dec. 25, 2012 Tel:886-2-2655-8100 Fax:886-2-2655-8200 Page No. : D1 of D3 Appendix D. Antenna Spec. Antenna Type: PCB Antenna Gain: 0 dBi 2.4GHz, Peak Gain: -29.42 dBi, Avg. Gain: -32.69 dBi 2.425GHz, Peak Gain: -30.02 dBi, Avg. Gain: -33.49 dBi CERPASS TECHNOLOGY CORP. Report No.: TEMJ1211033 Cerpass Technology Corp. Issued Date : Dec. 25, 2012 Tel:886-2-2655-8100 Fax:886-2-2655-8200 Page No. : D2 of D3 2.45GHz, Peak Gain: -30.44 dBi, Avg. Gain: -34.14 dBi 2.482GHz, Peak Gain: -30.95 dBi, Avg. Gain: -35.28 dBi CERPASS TECHNOLOGY CORP. Report No.: TEMJ1211033 Cerpass Technology Corp. Issued Date : Dec. 25, 2012 Tel:886-2-2655-8100 Fax:886-2-2655-8200 Page No. : D3 of D3 2.5GHz, Peak Gain: -31.63 dBi, Avg. Gain: -36.28 dBi

RF_160, Issue 02 Declaration of Authorization We Name:ATBS Technology Corporation Address:3F, No. 49, Lane 35, Jihu Rd., Neihu Chiu, City:Taipei, 114 Country:Taiwan Declare that: Name Representative of agent: Delia Feng (1) Agent Company name:Cerpass Technology Corporation Address:No.10, Lane 2, Lianfu Street, Luzhu District City:Taoyuan City 33848 Country:Taiwan, R.O.C. is authorized to apply for Certification of the following product(s): Product description:TPMS for iPod,iPhone,iPad Type designation:BT68XXX (X=0-9,A-Z,a-z or blank) Trademark:ATBS on our behalf. Date:Apr. 17, 2015 City:Taipei Name:Kelly Kuo (2) Function:Manager Signature:. Notes: (1): Required for FCC application (2): For FCC it must be the Grantee Code “owner” or the authorized agent.

DECLARATION OF CONFORMITY (DoC) Equipment:TPMS for iPod,iPhone,iPad Trademark(s):ATBS Model(s):BT68XXX (X=0-9,A-Z,a-z or blank) Manufacturer:ATBS Technology Corporation FCC ID in case other parts of this equipment are subject to certification: UP5-SC-BT6800 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)this device may not cause harmful interference, and (2)this device must accept any interference received, including interference that may cause undesired operation. The following test reports are subject to this declaration: Test report number:Issue date: TEFD1408162Apr. 01, 2015 Company name:ATBS Technology Corporation. Name/Title (legal representative):Kelly Kuo/ Manager Address:3F-4, No. 200, Kang-Chien Rd., Taipei 11494, Taiwan Phone:886-2-26562508 Fax:886-2-26562506 E-mail:[email protected] Date:Apr. 17, 2015 Signature:

CERPASS TECHNOLOGY CORP.Report No.: 1408162 Cerpass Technology Corp.Issued Date:Jun. 01, 2015 Page No.:A1 of A6 Photographs of EUT CERPASS TECHNOLOGY CORP.Report No.: 1408162 Cerpass Technology Corp.Issued Date:Jun. 01, 2015 Page No.:A2 of A6

Label & Location

CERPASS TECHNOLOGY CORP.Report No.: 1408162 Cerpass Technology Corp.Issued Date:Jun. 01, 2015 Page No.:A3 of A6 CERPASS TECHNOLOGY CORP.Report No.: 1408162 Cerpass Technology Corp.Issued Date:Jun. 01, 2015 Page No.:A4 of A6 CERPASS TECHNOLOGY CORP.Report No.: 1408162 Cerpass Technology Corp.Issued Date:Jun. 01, 2015 Page No.:A5 of A6 CERPASS TECHNOLOGY CORP.Report No.: 1408162 Cerpass Technology Corp.Issued Date:Jun. 01, 2015 Page No.:A6 of A6

CERPASS TECHNOLOGY CORP. Report No.: 1408162 Cerpass Technology Corp.Issued date:Apr. 01, 2015 Tel:886-3-3226-888 Fax:886-3-3226-881Page No.:1 of 3 FCC ID:UP5-SC-BT6800 Radio Frequency Exposure LIMIT According to §15.247(i), systems operating under the provisions of this section shall be operated in a manner that ensures that the public is not exposed to radio frequency energy levels in excess of the Commission's guidelines. See § 1.1307(b)(1) of this chapter. EUT Specification EUTTPMS for iPod,iPhone,iPad Frequency band (Operating) WLAN: 2.412GHz ~ 2.462GHz WLAN: 5.150GHz ~ 5.250GHz WLAN: 5.725GHz ~ 5.850GHz Bluetooth: 2.402GHz ~ 2.480 GHz Device category Portable (<20cm separation) Mobile (>20cm separation) Exposure classification Occupational/Controlled exposure (S = 5mW/cm 2 ) General Population/Uncontrolled exposure (S=1mW/cm 2 ) Antenna diversity Single antenna Multiple antennas Tx diversity Rx diversity Tx/Rx diversity Max. output power GFSK: -15.98dBm(0.0000252mW) /4-DQPSK: -15.95dBm(0.0000254mW) 8DPSK: -17.45Bm(0.0000180mW) Antenna gain (Max)0 dBi Evaluation applied MPE Evaluation* SAR Evaluation N/A Remark: 1. The maximum output power is -15.95 dBm (0.0000254 mW) at 2402MHz (with numeric 0 antenna gain.) 2. DTS device is not subject to routine RF evaluation; MPE estimate is used to justify the compliance. 3. For mobile or fixed location transmitters, no SAR consideration applied. The maximum power density is 1.0 mW/cm 2 even if the calculation indicates that the power density would be larger. CERPASS TECHNOLOGY CORP. Report No.: 1408162 Cerpass Technology Corp.Issued date:Apr. 01, 2015 Tel:886-3-3226-888 Fax:886-3-3226-881Page No.:2 of 3 FCC ID:UP5-SC-BT6800 TEST RESULTS No non-compliance noted. Calculation Given d GP E   30 & 3770 2 E S WhereE = Field strength in Volts / meter P = Power in Watts G = Numeric antenna gain d = Distance in meters S = Power density in milliwatts / square centimeter Combining equations and re-arranging the terms to express the distance as a function of the remaining variables yields: 2 3770 30 d GP S   Changing to units of mW and cm, using: P (mW) = P (W) / 1000 and d (cm) = d(m) / 100 Yields   2 2 0796.0 100/3770 1000/30 d GP d GP S     Equation 1 Whered = Distance in cm P = Power in mW G = Numeric antenna gain S = Power density in mW / cm 2 CERPASS TECHNOLOGY CORP. Report No.: 1408162 Cerpass Technology Corp.Issued date:Apr. 01, 2015 Tel:886-3-3226-888 Fax:886-3-3226-881Page No.:3 of 3 FCC ID:UP5-SC-BT6800 Maximum Permissible Exposure Modulation Mode Frequency band (MHz) Max. Conducted output power(dBm) Antenna gain (dBi) Distance (cm) Power density (mW/cm2) Limit (mW/cm2) GFSK2402-2480-15.98020 0 1 /4-DQPSK2402-2480-15.95020 0 1 8DPSK2402-2480-17.45020 0 1 NOTE: Total (Chain0+Chain1) , the formula of calculated the MPE is: CPD1 / LPD1 + CPD2 / LPD2 + ......etc. < 1 CPD = Calculation power density LPD = Limit of power density

CERPASS TECHNOLOGY CORP. Report No.: TEFB1408162 Cerpass Technology Corp.Issued Date: Apr. 01, 2015 Page No.:1 of 50 FCC ID:UP5-SC-BT6800 FCC RADIO TEST REPORT Applicant:ATBS Technology Corporation Address: 3F, No. 49, Lane 35, Jihu Rd., Neihu Chiu, Taipei, 114, Taiwan Equipment:TPMS for iPod,iPhone,iPad Model No.:BT68XXX (X=0-9,A-Z,a-z or blank) Trade Name : ATBS FCC ID: UP5-SC-BT6800 I HEREBY CERTIFY THAT : The sample was received on Mar. 06, 2015 and the testing was carried out onMar. 18, 2015 at Cerpass Technology Corp.The test result refers exclusively to the test presented test model / sample. Without written approval of Cerpass Technology Corp., the test report shall not be reproduced except in full. Approved by:Tested by: Hill Chen Manager Aiden Lu Engineer Laboratory Accreditation: Cerpass Technology Corporation Test Laboratory Cerpass Technology(SuZhou) Co., Ltd. CERPASS TECHNOLOGY CORP. Report No.: TEFB1408162 Cerpass Technology Corp.Issued Date:Apr. 01, 2015 Page No.:2 of 50 FCC ID:UP5-SC-BT6800 Contents 1.Summary of Test Procedure and Test Results................................................................................. 5 1.1Applicable Standards ................................................................................................................. 5 2.Test Configuration of Equipment under Test ................................................................................... 6 2.1Feature of Equipment under Test............................................................................................... 6 2.2Carrier Frequency of Channels .................................................................................................. 6 2.3Test Mode & Test Software ........................................................................................................ 7 2.4Description of Test System......................................................................................................... 7 2.5General Information of Test........................................................................................................ 8 3.Test Equipment and Ancillaries Used for Tests ............................................................................... 9 4.Antenna Requirements.....................................................................................................................10 4.1Standard Applicable .................................................................................................................10 4.2Antenna Construction and Directional Gain.............................................................................10 5.Test of AC Power Line Conducted Emission ................................................................................. 11 5.1Test Limit .................................................................................................................................. 11 5.2Test Procedures ....................................................................................................................... 11 5.3Typical Test Setup ....................................................................................................................12 5.4Test Result and Data ................................................................................................................13 5.5Test Photographs .....................................................................................................................15 6.Test of Spurious Emission (Radiated) ............................................................................................16 6.1Test Limit ..................................................................................................................................16 6.2Test Procedures .......................................................................................................................16 6.3Typical Test Setup ...................................................................................................................17 6.4Test Result and Data (9kHz ~ 30MHz).....................................................................................18 6.5Test Result and Data (30MHz ~ 1GHz)....................................................................................18 6.6Test Result and Data (Above 1GHz) ........................................................................................20 6.7Restricted Bands of Operation .................................................................................................26 6.8Restrict band emission Measurement Data .............................................................................27 6.9Test Photographs (30MHz ~ 1GHz) .........................................................................................29 6.10Test Photographs (Above 1GHz) .............................................................................................30 7.Test of Spurious Emission (Conducted).........................................................................................31 7.1Test Limit ..................................................................................................................................31 7.2Test Procedure .........................................................................................................................31 7.3Test Setup Layout ....................................................................................................................31 7.4Test Result and Data ................................................................................................................31 8.Occupied Bandwidth Measurement Data .......................................................................................35 8.1Test Limit ..................................................................................................................................35 8.2Test Procedures .........................................................................…

Text truncated - open the document above for the full version.

CERPASS TECHNOLOGY CORP. Report No.: TEFB1408162 Cerpass Technology Corp.Issued Date:Apr. 01, 2015 Page No.:15 of 50 FCC ID:UP5-SC-BT6800 5.5 Test Photographs Front View Rear View CERPASS TECHNOLOGY CORP. Report No.: TEFB1408162 Cerpass Technology Corp.Issued Date:Apr. 01, 2015 Page No.:29 of 50 FCC ID:UP5-SC-BT6800 6.9 Test Photographs (30MHz ~ 1GHz) Front View Rear View CERPASS TECHNOLOGY CORP. Report No.: TEFB1408162 Cerpass Technology Corp.Issued Date:Apr. 01, 2015 Page No.:30 of 50 FCC ID:UP5-SC-BT6800 6.10 Test Photographs (Above 1GHz) Front View Rear View