UZ7DS8288RCordless Scanner

Regulatory Engineering Zebra Technologies Corporation 3 Overlook Point, | Lincolnshire, Illinois 60069 | 1.631.738.2400 phone | 1.631.627.7179 fax | www.zebra.com Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia MD 21046 USA Date: December 12, 2025 Ref: Attestation Statements Part 2.911(d)(7) Filing Grantee Code: UZ7 Zebra Technologies Corporation (“the applicant”) as required by section 2.911(d)(7), will also serve as the agent for service of process for the above referenced FCC Grantee Code. The service of process includes, but is not limited to, delivery of any correspondence, notices, orders, decisions, and requirements of administrative, legal, or judicial process related to Commission proceedings. The applicant acknowledges that they will maintain an agent for service of process in the United States for no less than one year after either the grantee has permanently terminated all marketing and importation of the applicable equipment within the U.S., or the conclusion of any Commission-related administrative or judicial proceeding involving the equipment, whichever is later. The applicant further acknowledges their responsibility to inform the FCC whenever the following agent information changes. Company Name: Zebra Technologies Corporation Company US Address: 3 Overlook Point, Lincolnshire, IL, United States, 60069 Contact Person: Jay Cadiz Email: [email protected] Telephone number: 847-616-5806 or 224-532-6912 FRN: 0015642663 Sincerely yours, Signed by the Applicant Signed by the Agent _______________________ ______________________ Dharmajit Solanki [email protected] Jay Cadiz [email protected]

Regulatory Engineering Zebra Technologies Corporation 3 Overlook Point, | Lincolnshire, Illinois 60069 | 4169706612 phone | www.zebra.com Federal Communications Commission 7435 Oakland Mills Road Columbia MD 21046 Date: June 12, 2026 Subject: Certifications concerning “covered” equipment pursuant to Part 2.911(d)(5)(i) and (ii) FCC ID: UZ7DS8288R To whom it may concern, Zebra Technologies Corporation (“the applicant”) certifies that the equipment for which authorization is sought is not the equipment on the Covered List, as established pursuant to § 1.50002 of CFR Title 47, that is prohibited from obtaining an equipment authorization under this subpart. This includes equipment that: (1) Has been certified as a modular transmitter; or (2) Meets the modular transmitter requirements of § 15.212 of this chapter and could be certified as a modular transmitter. pursuant to section 2.903 resulting in the recent adoption of FCC 25-71 (et al., ET Docket No. 21-232, Second Report and Order); or (3) Uncrewed aircraft systems (UAS) and UAS critical components produced in a foreign country and all communications and video surveillance equipment and services listed in Section 1709(a)(1) of the FY25 National Defense Authorization Act (Pub. L. 118-159) Applicant certifies that, as of the date of the filing of the application, the applicant [is not] identified on the Covered List (as a specifically named entity or any of its subsidiaries or affiliates) as an entity producing “covered” equipment. Applicant further certifies that no Cybersecurity or anti-virus software produced or provided by Kaspersky Lab, Inc. or any of its successors and assignees, including equipment with integrated Kaspersky Lab, Inc. (or any of its successors and assignees) cybersecurity or anti-virus software is installed in the equipment being certified. The above-referenced Covered List is published by the Public Safety and Homeland Security Bureau (PSHSB), pursuant to Section 1.50002 of the Commission’s rules. Sincerely, ________________________ Name: Dharmajit Solanki E-mail: [email protected]

Regulatory Engineering Zebra Technologies Corporation 3 Overlook Point, | Lincolnshire, Illinois 60069 | 4169706612 phone | www.zebra.com Date: June 12, 2026 Federal Communications Commission Office of Engineering and Technology Equipment Authorization Division 7435 Oakland Mills Road Columbia, MD 21046 Ref: FCC ID: UZ7DS8288R AUTHORIZATION LETTER We, the undersigned, hereby authorize Jones Tsai in Sporton International Inc. to act on our behalf in all manners relating to FCC application for equipment authorization, including signing of all documents relating to these matters. Any and all acts carried out by Jones Tsai in Sporton International Inc. on our behalf shall have the same effect as acts of our own. If you have any acknowledgement or response, please send it to Sporton International Inc. directly. Confidentiality Request Pursuant to the provisions of Sections 0.457 and 0.459 of Commission’s rules (47CFR§§0.457, 0.459), we are requesting the Commission to withhold the following attachment(s) as confidential document from public disclosure indefinitely.  Tune Up Procedure  Operational Description  Block Diagram  Schematic Diagram  Parts List Above mentioned document contains detailed system and equipment description are considered as proprietary information in operation of the equipment. The public disclosure of above documents might be harmful to our company and would give competitor an unfair advantage in the market. In addition to above mentioned documents, pursuant to Public Notice DA 04-1705 of the Commission’ s policy, in order to comply with the marketing regulations in 47 CFT §2.803 and the importation rules in 47 CFR §2.1204, while ensuring that business sensitive information remains confidential until the actual marketing of newly authorized devices. We are requesting the commission to grant short-term confidentiality request on the following attachment(s) for 180 days after the grant as outlined in Public Notice DA 04-1705.  Internal Photos  External Photos  Test Setup Photos Regulatory Engineering Zebra Technologies Corporation 3 Overlook Point, | Lincolnshire, Illinois 60069 | 4169706612 phone | www.zebra.com  User Manual It is our understanding that all measurement test reports, FCC ID label format and correspondent during certification review process cannot be granted as confidential documents and that information will be available for public review once the grant of equipment authorization is issued. If you have any questions regarding this authorization, please contact me directly. ________________________ Dharmajit Solanki [email protected]

DWG. NO.: Date: 01/09/26 REV Drawn By: T. Hsieh Approved by: HOLTSVILLE, N.Y. 11742 DRAWING SCALE: 1 / 1 PRINTOUT @ 100% OF ACTUAL SIZE PLEASE NOTE: Do NOT Change Colors, Size or Type Fonts in the Artwork PRINTER NOTE: This proof indicates color break only and may not accurately reflect actual production colors. Die lines and call-outs are for reference only - DO NOT PRINT This title block must remain on the electronic file for all proofs. A ©ZIH CORP. 2005 ALL RIGHTS RESERVED THE INFORMATION CONTAINED HEREIN IS THE CONFIDENTIAL AND THE EXCLUSIVE PROPERTY OF ZIH CORP. THIS DOCUMENT, AND THE INFORMATION CONTAINED HEREIN, SHALL NOT BE COPIED, REPRODUCED, PUBLISHED, DISPLAYED OR DISTRIBUTED, IN WHOLE OR IN PART, IN ANY MEDIUM, BY ANY MEANS, FOR ANY PURPOSE WITHOUT THE EXPRESS WRITTEN CONSENT OF ZIH CORP. DIMENSIONS ARE IN INCHES AR-002252-01 PROD FAM: DS8288R DESCRIPTION: LBL: LCD, ARTWORK DS8288R CTRY CODE: ROW S/N: XXXXXXXXXXXX MFD: XXXXXXX MADE IN XXXXXX P/N: XXXXXXXXXXXXX XXXX CCXXxxLPyyyZz X-00000 CMIIT ID: XXXXYYZZZZ ANATEL: HHHHH-AA-FFFFF R-C-ZTC-DS8288R MODEL : DS8288R FCC ID: UZ7DS8288R IC: 109AN-DS8288R 條碼掃描 器 ZEBRA TECHNOLOGIES CORP. LINCOLNSHIRE, IL 60069 5V 1.2A DESIGNED BY: 17.33 MM 60.09 MM NOTES: 1. SCRIPT FILE TO BE CREATED BY MANUFACTURIN G PER SP-10083-01 SCRIPT FILE MUST MATCH 0225201A EXACTLY AND H AVE SAME REVISION. 2. LABEL STOCK P/N IS SUBJECT TO CHANGE. CHECK BOM FOR ACTUAL PART NUMBER. 3. ALL CASES "XXX..." REPRESENTS VARIABLE FIELDS IN SCRIPT FILE. 4. SERIAL NUMBER MUST BE 4PT MINIMUM CHARACTER HEIGHT IN SCRIPT FILE. 5. PART NUMBER MAY OR MAY NOT HAVE DASH BEFORE COUNTRY CODE. SEE BOM FOR ACTUAL MODEL DESCRIPTION. 6. "MFD:" REPRESENTS MANUFACTURE DAY, MONTH, YEAR (IE: 12SEP15) 7. COUNTRY OF ORIGIN REQUIRED. 8. PLANT CODE REQUIRED. TO BE LOCATED BY MANUFACTURING FOR BEST FIT IN SCRIPT FILE. 9. LBL STOCK: LB-XXX_LBL_MFG_DS82XX_REV-1 10. BMP 600 DPI SIZE MM MARKINGS AND DIMENSIONS SHALL REMAIN THE SAME SIZE WHEN PRINTED. Boundary line - Do not print.

Sideview of the device Label location

TEL : 886-3-327-3456 Page 1 of 21 FAX : 886-3-328-4978 Issued Date : Jun. 12, 2026 Template version: 240125 FCC SAR TEST REPORT Report No. : FA610506 FCC SAR TEST REPORT FCC ID : UZ7DS8288R Equipment : Cordless Scanner Brand Name : Zebra Model Name : DS8288R Applicant : Zebra Technologies Corporation 3 Overlook Point, Lincolnshire, IL 60069 USA Manufacturer : Zebra Technologies Corporation 3 Overlook Point, Lincolnshire, IL 60069 USA Standard : FCC 47 CFR Part 2 (2.1093) The product was received on May 19, 2026 and testing was started from May 27, 2026 and completed on May 28, 2026. We, SPORTON INTERNATIONAL INC., would like to declare that the tested sample provide by manufacturer and the test data has been evaluated in accordance with the test procedures given in 47 CFR Part 2.1093 and FCC KDB and has been pass the FCC requirement. The test results in this report apply exclusively to the tested model / sample. Without written approval of SPORTON INTERNATIONAL INC. Laboratory, the test report shall not be reproduced except in full. Sporton International Inc. EMC & Wireless Communications Laboratory No.52, Huaya 1st Rd., Guishan Dist., Taoyuan City 333, Taiwan Approved by: Cona Huang / Deputy Manager TEL : 886-3-327-3456 Page 2 of 21 FAX : 886-3-328-4978 Issued Date : Jun. 12, 2026 Template version: 240125 FCC SAR TEST REPORT Report No. : FA610506 Table of Contents 1. Statement of Compliance ............................................................................................................................................. 4 2. Guidance Applied .......................................................................................................................................................... 4 3. Equipment Under Test (EUT) Information ................................................................................................................... 5 3.1 General Information ............................................................................................................................................... 5 4. RF Exposure Limits....................................................................................................................................................... 6 4.1 Uncontrolled Environment ...................................................................................................................................... 6 4.2 Controlled Environment .......................................................................................................................................... 6 5. Specific Absorption Rate (SAR) ................................................................................................................................... 7 5.1 Introduction ............................................................................................................................................................ 7 5.2 SAR Definition ........................................................................................................................................................ 7 6. System Description and Setup .................................................................................................................................... 8 6.1 Test Site Location ................................................................................................................................................... 8 6.2 E-Field Probe ......................................................................................................................................................... 9 6.3 Data Acquisition Electronics (DAE) ........................................................................................................................ 9 6.4 Phantom ................................................................................................................................................................10 6.5 Device Holder........................................................................................................................................................ 11 7. Measurement Procedures ...........................................................................................................................................12 7.1 Spatial Peak SAR Evaluation ................................................................................................................................12 7.2 Power Reference Measurement............................................................................................................................13 7.3 Area Scan .............................................................................................................................................................13 7.4 Zoom Scan ............................................................................................................................................................14 7.5 Volume Scan Procedures ......................................................................................................................................14 7.6 Power Drift Monitoring ...........................................................................................................................................14 8. Test Equipment List .....................................................................................................................................................15 9. System Verification ......................................................................................................................................................16 9.1 Tissue Verification .................................................................................................................................................16 9.2 System Performance Check Results .....................................................................................................................16 10. Output Power (Unit: dBm) .....…

Text truncated - open the document above for the full version.

SPORTON INTERNATIONAL INC. TEL : 886-3-327-3456 FAX : 886-3-328-4978 D900V2, serial no. 1D171 Extended Dipole Calibrations If dipoles are verified in return loss (<-20dB, within 20% of prior calibration), and in impedance (within 5 ohm of prior calibration), the annual calibration is not necessary and the calibration interval can be extended. <Justification of the extended calibration> D900V2 – serial no. 1D171 900MHZ Date of Measurement Return-Loss (dB) Delta (%) Real Impedance (ohm) Delta (ohm) Imaginary Impedance (ohm) Delta (ohm) 03.12.2025 (Cal. Report) -29.824 49.732 -3.209 03.11.2026 (extended) -29.522 1.013 49.488 -0.244 -3.2574 -0.0484 The return loss is < -20dB, within 20% of prior calibration; the impedance is within 5 ohm of prior calibration. Therefore the verification result should support extended calibration. SPORTON INTERNATIONAL INC. TEL : 886-3-327-3456 FAX : 886-3-328-4978 <Dipole Verification Data> - D900V2, serial no. 1D171 (Data of Measurement : 03.11.2026) 900 MHz - Head SPORTON INTERNATIONAL INC. TEL : 886-3-327-3456 FAX : 886-3-328-4978 D2450V2, serial no. 736 Extended Dipole Calibrations If dipoles are verified in return loss (<-20dB, within 20% of prior calibration), and in impedance (within 5 ohm of prior calibration), the annual calibration is not necessary and the calibration interval can be extended. <Justification of the extended calibration> D2450V2 – serial no. 736 2450MHZ Date of Measurement Return-Loss (dB) Delta (%) Real Impedance (ohm) Delta (ohm) Imaginary Impedance (ohm) Delta (ohm) 08.15.2024 (Cal. Report) -26.2 54.6 +2.1 08.14.2025 (extended) -26.383 0.69 55.071 0.471 +2.6474 0.5474 The return loss is < -20dB, within 20% of prior calibration; the impedance is within 5 ohm of prior calibration. Therefore the verification result should support extended calibration. SPORTON INTERNATIONAL INC. TEL : 886-3-327-3456 FAX : 886-3-328-4978 <Dipole Verification Data> - D2450 V2, serial no. 736 (Data of Measurement : 08.14.2025) 2450MHz - Head

0 dB = 1.36 W/kg = 1.34 dBW/kg Test Laboratory: Sporton International Inc. SAR/HAC Testing Lab Date: 2026/5/27 #01_RFID_Right Side_5mm Communication System: RFID; Frequency: 914.75 MHz Medium: HSL_600-7200_260527 Medium parameters used: f = 915 MHz; σ = 0.949 S/m; ε r = 43.235; ρ = 1000 kg/m 3 Ambient Temperature：23.7 °C; Liquid Temperature：22.7 °C DASY5 Configuration: - Probe: EX3DV4 - SN7306; ConvF(9.2, 8.93, 9.41) @ 914.75 MHz; Calibrated: 2025/7/28 - Sensor-Surface: 1.4mm (Mechanical Surface Detection) - Electronics: DAE4 Sn1794; Calibrated: 2026/2/16 - Phantom: SAM_Left; Type: QD000P40CD; Serial: 1685 - Measurement SW: DASY52, Version 52.10 (4);SEMCAD X Version 14.6.14 (7501) Area Scan (81x81x1): Interpolated grid: dx=1.500 mm, dy=1.500 mm Maximum value of SAR (interpolated) = 1.31 W/kg Zoom Scan (5x5x7)/Cube 0: Measurement grid: dx=8mm, dy=8mm, dz=5mm Reference Value = 4.262 V/m; Power Drift = -0.15 dB Peak SAR (extrapolated) = 1.56 W/kg SAR(1 g) = 0.931 W/kg; SAR(10 g) = 0.507 W/kg (SAR corrected for target medium) Smallest distance from peaks to all points 3 dB below = 11.2 mm Ratio of SAR at M2 to SAR at M1 = 58.5% Maximum value of SAR (measured) = 1.36 W/kg Test Laboratory: Sporton International Inc. SAR/HAC Testing Lab Date: 2026/5/28 #02_Bluetooth_1Mbps_Top_5mm_Ch39 Communication System: UID 10670 - AAA, Bluetooth; Frequency: 2441 MHz Medium: HSL_600-7200_260528 Medium parameters used : f = 2441 MHz; σ = 1.85 S/m; ε r = 42.04; ρ = 1000 kg/m 3 Ambient Temperature：23.7 °C; Liquid Temperature：22.7 °C DASY5 Configuration: - Probe: EX3DV4 - SN7822; ConvF(6.61, 6.49, 6.71) @ 2441 MHz; Calibrated: 2025/9/11 - Sensor-Surface: 1.4mm (Mechanical Surface Detection) - Electronics: DAE4 Sn853; Calibrated: 2025/9/9 - Phantom: SAM_Left; Type: QD000P40CD; Serial: 1719 - Measurement SW: DASY52, Version 52.10 (4);SEMCAD X Version 14.6.14 (7501) Area Scan (91x91x1): Interpolated grid: dx=1.200 mm, dy=1.200 mm Maximum value of SAR (interpolated) = 0.00539 W/kg Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = 1.005 V/m; Power Drift = 0.05 dB Peak SAR (extrapolated) = 0.0450 W/kg SAR(1 g) = 0.00126 W/kg; SAR(10 g) = 0.000279 W/kg (SAR corrected for target medium) Smallest distance from peaks to all points 3 dB below: Larger than measurement grid (> 15 mm) Ratio of SAR at M2 to SAR at M1 = 0% Maximum value of SAR (measured) = 0.0448 W/kg 0 dB = 0.0448 W/kg = -13.49 dBW/kg 0 dB = 1.16 W/kg = 0.64 dBW/kg Test Laboratory: Sporton International Inc. SAR/HAC Testing Lab Date: 2026/5/27 #03_RFID_Right Side_6mm Communication System: RFID; Frequency: 914.75 MHz Medium: HSL_600-7200_260527 Medium parameters used: f = 915 MHz; σ = 0.949 S/m; ε r = 43.235; ρ = 1000 kg/m 3 Ambient Temperature：23.7 °C; Liquid Temperature：22.7 °C DASY5 Configuration: - Probe: EX3DV4 - SN7306; ConvF(9.2, 8.93, 9.41) @ 914.75 MHz; Calibrated: 2025/7/28 - Sensor-Surface: 1.4mm (Mechanical Surface Detection) - Electronics: DAE4 Sn1794; Calibrated: 2026/2/16 - Phantom: SAM_Left; Type: QD000P40CD; Serial: 1685 - Measurement SW: DASY52, Version 52.10 (4);SEMCAD X Version 14.6.14 (7501) Area Scan (81x81x1): Interpolated grid: dx=1.500 mm, dy=1.500 mm Maximum value of SAR (interpolated) = 1.13 W/kg Zoom Scan (5x5x7)/Cube 0: Measurement grid: dx=8mm, dy=8mm, dz=5mm Reference Value = 4.330 V/m; Power Drift = -0.18 dB Peak SAR (extrapolated) = 1.30 W/kg SAR(1 g) = 0.829 W/kg; SAR(10 g) = 0.466 W/kg (SAR corrected for target medium) Smallest distance from peaks to all points 3 dB below = 11.2 mm Ratio of SAR at M2 to SAR at M1 = 61.4% Maximum value of SAR (measured) = 1.16 W/kg

Test Laboratory: Sporton International Inc. SAR/HAC Testing Lab Date: 2026/5/27 System Check_Head_900MHz DUT: D900V2 - SN1d171 Communication System: CW; Frequency: 900 MHz;Duty Cycle: 1:1 Medium: HSL_600-7200_260527 Medium parameters used: f = 900 MHz; σ = 0.942 S/m; ε r = 43.278; ρ = 1000 kg/m 3 Ambient Temperature：23.7 °C; Liquid Temperature：22.7 °C DASY5 Configuration: - Probe: EX3DV4 - SN7306; ConvF(9.2, 8.93, 9.41) @ 900 MHz; Calibrated: 2025/7/28 - Sensor-Surface: 1.4mm (Mechanical Surface Detection) - Electronics: DAE4 Sn1794; Calibrated: 2026/2/16 - Phantom: SAM_Left; Type: QD000P40CD; Serial: 1685 - Measurement SW: DASY52, Version 52.10 (4);SEMCAD X Version 14.6.14 (7501) Pin=250mW/Area Scan (61x61x1): Interpolated grid: dx=1.500 mm, dy=1.500 mm Maximum value of SAR (interpolated) = 3.56 W/kg Pin=250mW/Zoom Scan (5x5x7)/Cube 0: Measurement grid: dx=8mm, dy=8mm, dz=5mm Reference Value = 64.67 V/m; Power Drift = -0.10 dB Peak SAR (extrapolated) = 3.80 W/kg SAR(1 g) = 2.66 W/kg; SAR(10 g) = 1.73 W/kg (SAR corrected for target medium) Smallest distance from peaks to all points 3 dB below = 16 mm Ratio of SAR at M2 to SAR at M1 = 67.4% Maximum value of SAR (measured) = 3.42 W/kg 0 dB = 3.42 W/kg = 5.34 dBW/kg Test Laboratory: Sporton International Inc. SAR/HAC Testing Lab Date: 2026/5/28 System Check_Head_2450MHz DUT: D2450V2-736 Communication System: CW; Frequency: 2450 MHz Medium: HSL_600~7200_260528 Medium parameters used : f = 2450 MHz; σ = 1.857 S/m; ε r = 42.026; ρ = 1000 kg/m 3 Ambient Temperature：23.7 °C; Liquid Temperature：22.7 °C DASY5 Configuration: - Probe: EX3DV4 - SN7822; ConvF(6.61, 6.49, 6.71) @ 2450 MHz; Calibrated: 2025/9/11 - Sensor-Surface: 1.4mm (Mechanical Surface Detection) - Electronics: DAE4 Sn853; Calibrated: 2025/9/9 - Phantom: SAM_Left; Type: QD000P40CD; Serial: 1719 - Measurement SW: DASY52, Version 52.10 (4);SEMCAD X Version 14.6.14 (7501) Pin=50mW/Area Scan (71x71x1): Interpolated grid: dx=1.200 mm, dy=1.200 mm Maximum value of SAR (interpolated) = 4.49 W/kg Pin=50mW/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = 51.66 V/m; Power Drift = -0.01 dB Peak SAR (extrapolated) = 5.46 W/kg SAR(1 g) = 2.78 W/kg; SAR(10 g) = 1.31 W/kg (SAR corrected for target medium) Smallest distance from peaks to all points 3 dB below = 9 mm Ratio of SAR at M2 to SAR at M1 = 51.1% Maximum value of SAR (measured) = 4.54 W/kg 0 dB = 4.54 W/kg = 6.57 dBW/kg

Page Number : C1 of C19 FCC RADIO TEST REPORT Report No. :FR610506B Appendix C. Radiated Spurious Emission Test Data Test Engineer : Jesse Wang, Stan Hsieh, and Ken Wu Temperature : 18.2~21.3°C Relative Humidity : 56.4~68.6% Note symbol -L Low channel location -R High channel location Page Number : C2 of C19 FCC RADIO TEST REPORT Report No. :FR610506B C1.Radiated Spurious Emission Test Modes Mode Band (MHz) Antenna Modulation Channel Frequency Data Rate RU Remark Mode 6 2400-2483.5 0 Bluetooth-LE GSFK 00 2402 1Mbps - - Mode 7 2400-2483.5 0 Bluetooth-LE GSFK 19 2440 1Mbps - - Mode 8 2400-2483.5 0 Bluetooth-LE GSFK 39 2480 1Mbps - - Mode 9 2400-2483.5 0 Bluetooth-LE GSFK 19 2440 1Mbps - LF Mode 10 2400-2483.5 0 Bluetooth-LE GSFK 19 2440 1Mbps - SHF Page Number : C3 of C19 FCC RADIO TEST REPORT Report No. :FR610506B C2.Summary of each worse mode Mode Modulation Ch. Freq. (MHz) Level (dBuV/m) Limit (dBuV/m) Margin (dB) Pol. Peak Avg. Result RU Remark 6 Bluetooth-LE GSFK 00 4804.00 44.44 74.00 -29.56 V Peak Pass - Harmonic 7 Bluetooth-LE GSFK 19 2498.08 48.41 54.00 -5.59 V Avg. Pass - Band Edge Bluetooth-LE GSFK 19 7320.00 43.65 74.00 -30.35 V Peak Pass - Harmonic 8 Bluetooth-LE GSFK 39 2484.32 48.08 54.00 -5.92 H Avg. Pass - Band Edge Bluetooth-LE GSFK 39 4960.00 43.77 74.00 -30.23 H Peak Pass - Harmonic 9 LF 19 30.97 30.50 40.00 -9.50 V Peak Pass - LF 10 SHF 19 24977.79 38.22 74.00 -35.78 V Peak Pass - SHF Page Number : C4 of C19 FCC RADIO TEST REPORT Report No. :FR610506B Mode 6 Band Edge 2400-2483.5_Bluetooth-LE GSFK_CH00_2402MHz ANT 0 Pol. Horizontal Fundamental Peak Avg Page Number : C5 of C19 FCC RADIO TEST REPORT Report No. :FR610506B Mode 6 Band Edge 2400-2483.5_Bluetooth-LE GSFK_CH00_2402MHz ANT 0 Pol. Vertical Fundamental Peak Avg Page Number : C6 of C19 FCC RADIO TEST REPORT Report No. :FR610506B Mode 6 Harmonic 2400-2483.5_Bluetooth-LE GSFK_CH00_2402MHz ANT 0 Pol. Horizontal Vertical Peak Avg Page Number : C7 of C19 FCC RADIO TEST REPORT Report No. :FR610506B Mode 6 Harmonic 2400-2483.5_Bluetooth-LE GSFK_CH00_2402MHz ANT 0 Pol. Horizontal Vertical 14.47G ~14.5G Avg 17.7G ~18G Avg Page Number : C8 of C19 FCC RADIO TEST REPORT Report No. :FR610506B Mode 7 Band Edge - L 2400-2483.5_Bluetooth-LE GSFK_CH19_2440MHz ANT 0 Pol. Horizontal Fundamental Peak Avg Page Number : C9 of C19 FCC RADIO TEST REPORT Report No. :FR610506B Mode 7 Band Edge - R 2400-2483.5_Bluetooth-LE GSFK_CH19_2440MHz ANT 0 Pol. Horizontal Fundamental Peak Blank Avg Blank Page Number : C10 of C19 FCC RADIO TEST REPORT Report No. :FR610506B Mode 7 Band Edge - L 2400-2483.5_Bluetooth-LE GSFK_CH19_2440MHz ANT 0 Pol. Vertical Fundamental Peak Avg Page Number : C11 of C19 FCC RADIO TEST REPORT Report No. :FR610506B Mode 7 Band Edge - R 2400-2483.5_Bluetooth-LE GSFK_CH19_2440MHz ANT 0 Pol. Vertical Fundamental Peak Blank Avg Blank Page Number : C12 of C19 FCC RADIO TEST REPORT Report No. :FR610506B Mode 7 Harmonic 2400-2483.5_Bluetooth-LE GSFK_CH19_2440MHz ANT 0 Pol. Horizontal Vertical Peak Avg Page Number : C13 of C19 FCC RADIO TEST REPORT Report No. :FR610506B Mode 7 Harmonic 2400-2483.5_Bluetooth-LE GSFK_CH19_2440MHz ANT 0 Pol. Horizontal Vertical 14.47G ~14.5G Avg 17.7G ~18G Avg Page Number : C14 of C19 FCC RADIO TEST REPORT Report No. :FR610506B Mode 8 Band Edge 2400-2483.5_Bluetooth-LE GSFK_CH39_2480MHz ANT 0 Pol. Horizontal Fundamental Peak Avg Page Number : C15 of C19 FCC RADIO TEST REPORT Report No. :FR610506B Mode 8 Band Edge 2400-2483.5_Bluetooth-LE GSFK_CH39_2480MHz ANT 0 Pol. Vertical Fundamental Peak Avg Page Number : C16 of C19 FCC RADIO TEST REPORT Report No. :FR610506B Mode 8 Harmonic 2400-2483.5_Bluetooth-LE GSFK_CH39_2480MHz ANT 0 Pol. Horizontal Vertical Peak Avg Page Number : C17 of C19 FCC RADIO TEST REPORT Report No. :FR610506B Mode 8 Harmonic 2400-2483.5_Bluetooth-LE GSFK_CH39_2480MHz ANT 0 Pol. Horizontal Vertical 14.47G ~14.5G Avg 17.7G ~18G Avg Page Number : C18 of C19 FCC RADIO TEST REPORT Report No. :FR610506B Mode 9 LF 2400-2483.5_Bluetooth-LE GSFK_CH19_2440MHz ANT 0 Pol. Horizontal Vertical QP/ Peak Page Number : C19 of C19 FCC RADIO TEST REPORT Report No. :FR610506B Mode 10 SHF 2400-2483.5_Bluetooth-LE GSFK_CH19_2440MHz ANT 0 Pol. Horizontal Vertical Peak Page Number : D1 of D1 FCC RADIO TEST REPORT Report No. : FR610506B Appendix D. Duty Cycle Plots Antenna Band Duty Cycle (%) T(us) 1/T(kHz) VBW Setting 0 Bluetooth - LE for 1Mbps 15.04 94 10.64 11kHz <Ant. 0> Bluetooth - LE for 1Mbps

TEL : 886-3-327-3456 Page Number : 1 of 24 FAX : 886-3-328-4978 Issue Date : Jun. 10, 2026 Report Template No.: BU5-FR15CBT4.0 Version 2.4 Report Version : 01 FCC RADIO TEST REPORT Report No. : FR610506B FCC RADIO TEST REPORT FCC ID : UZ7DS8288R Equipment : Cordless Scanner Brand Name : Zebra Model Name : DS8288R Applicant : Zebra Technologies Corporation 3 Overlook Point, Lincolnshire, IL 60069 USA Manufacturer : Zebra Technologies Corporation 3 Overlook Point, Lincolnshire, IL 60069 USA Standard : FCC Part 15 Subpart C §15.247 The product was received on May 06, 2026 and testing was performed from May 13, 2026 to May 25, 2026. We, Sporton International Inc. EMC & Wireless Communications Laboratory, would like to declare that the tested sample has been evaluated in accordance with the test procedures and has been in compliance with the applicable technical standards. The test results in this report apply exclusively to the tested model / sample. Without written approval from Sporton International Inc. EMC & Wireless Communications Laboratory, the test report shall not be reproduced except in full. Approved by: Louis Wu Sporton International Inc. EMC & Wireless Communications Laboratory No. 52, Huaya 1st Rd., Guishan Dist., Taoyuan City 333, Taiwan (R.O.C.) TEL : 886-3-327-3456 Page Number : 2 of 24 FAX : 886-3-328-4978 Issue Date : Jun. 10, 2026 Report Template No.: BU5-FR15CBT4.0 Version 2.4 Report Version : 01 FCC RADIO TEST REPORT Report No. : FR610506B Table of Contents History of this test report ................................................................................................................................. 3 Summary of Test Result................................................................................................................................... 4 1 General Description ................................................................................................................................... 5 1.1 Product Feature of Equipment Under Test ........................................................................................ 5 1.2 Product Specification of Equipment Under Test ................................................................................ 5 1.3 Modification of EUT ........................................................................................................................... 6 1.4 Testing Location ................................................................................................................................ 6 1.5 Applicable Standards ......................................................................................................................... 6 2 Test Configuration of Equipment Under Test ......................................................................................... 7 2.1 Carrier Frequency Channel ............................................................................................................... 7 2.2 Test Mode ....................................…

Text truncated - open the document above for the full version.