UZ7MC3401Mobile Computer

Regulatory Engineering Zebra Technologies Corporation 1 Zebra Plaza, | Holtsville, NY 11742 | 1.631.738.2400 phone | 1.631.627.7179 fax | www.zebra.com Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia MD 21046 USA Date: April 12, 2024 Ref: Attestation Statements Part 2.911(d)(7) Filing Grantee Code: UZ7 Zebra Technologies Corporation (“the applicant”) as required by section 2.911(d)(7), will also serve as the agent for service of process for the above referenced FCC Grantee Code. The service of process includes, but is not limited to, delivery of any correspondence, notices, orders, decisions, and requirements of administrative, legal, or judicial process related to Commission proceedings. The applicant acknowledges that they will maintain an agent for service of process in the United States for no less than one year after either the grantee has permanently terminated all marketing and importation of the applicable equipment within the U.S., or the conclusion of any Commission-related administrative or judicial proceeding involving the equipment, whichever is later. The applicant further acknowledges their responsibility to inform the FCC whenever the following agent information changes. Company Name: Zebra Technologies Corporation Company US Address: 1 Zebra Plaza, Holtsville, New York, United States, 11742 Contact Person: Larry (Qianlin) Zhou Email: [email protected] Telephone number: 346-260-3543 FRN: 0015642663 Sincerely yours, Signed by the Applicant Signature : _______________________________ Name and Job Title. : Larry (Qianlin) Zhou / Regulatory Specialist E-mail : [email protected] Tel. : 346-260-3543

Regulatory Engineering Zebra Technologies Corporation 1 Zebra Plaza, | Holtsville, NY 11742 | 1.631.738.2400 phone | 1.631.627.7179 fax | www.zebra.com Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Date: May 24, 2024 Ref: Attestation Statements Part 2.911(d)(5)(i) Filing FCC ID: UZ7MC3401 Zebra Technologies Corporation (“the applicant”) certifies that the equipment for which authorization is sought is not “covered” equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. Sincerely, Signature : _______________________________ Name and Job Title. : Larry (Qianlin) Zhou / Regulatory Specialist E-mail : [email protected] Tel. : 346-260-3543 Regulatory Engineering Zebra Technologies Corporation 1 Zebra Plaza, | Holtsville, NY 11742 | 1.631.738.2400 phone | 1.631.627.7179 fax | www.zebra.com Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Date: May 24, 2024 Ref: Attestation Statements Part 2.911(d)(5)(ii) Filing FCC ID: UZ7MC3401 Zebra Technologies Corporation (“the applicant”) certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List (as a specifically named entity or any of its subsidiaries or affiliates) as an entity producing “covered” equipment. Sincerely, Signature : _______________________________ Name and Job Title. : Larry (Qianlin) Zhou / Regulatory Specialist E-mail : [email protected] Tel. : 346-260-3543

Regulatory Engineering Zebra Technologies Corporation 1 Zebra Plaza | Holtsville, NY 11742 | 1.631.738.2400 phone | 1.631.627.7179 fax | www.zebra.com Date: July 3, 2024 Subject: Product Equality Declaration To whom it may concern, We, Zebra Technologies Corporation, declare on our sole responsibility for the product of FCC ID: UZ7MC3401, IC: 109AN-MC3401 as below: FCC ID: UZ7MC3401, IC: 109AN-MC3401 has variant SKUs. The SKUs are electronically identical. The differences between SKUs are listed below: Stage MC34 WLAN SKU list Configuration SKU5 SKU6 SKU7 SKU8 SKU9 SKU10 SKU11 SKU12 SKU13 WW/WL WLAN WLAN WLAN WLAN WLAN WLAN WLAN WLAN WLAN Form Factor FA FA FA FA FA FA FA FA FA SKU Prem Prem Prem Prem Prem+ Prem+ Prem+ Prem+ Prem+ Brick / Gun Gun Gun Gun Brick Gun Gun Gun Brick Brick DDR size 6GB 6GB 6GB 6GB 6GB 6GB 6GB 6GB 6GB UFS size 64GB 64GB 64GB 64GB 128GB 128GB 128GB 128GB 128GB Scan engine SE4770 SE5500 SE5800 SE4770 SE5500 SE5800 SE5800 SE5800 SE5800 FF Camera None None None None 5MP (PN) 5MP (PN) 5MP (PN) 5MP (PN) 5MP (PN) RF Camera 13MP (PN) 13MP (PN) 13MP (PN) 13MP (PN) 13MP (PN) Keypad 38 38 47 38 47 47 47 38 38 Except listings above, the other relevant parts are the same. Should you have any questions or comments regarding this matter, please don’t hesitate to contact me. Yours sincerely Regulatory Engineering Zebra Technologies Corporation 1 Zebra Plaza | Holtsville, NY 11742 | 1.631.738.2400 phone | 1.631.627.7179 fax | www.zebra.com Signature : _______________________________ Name and Job Title. : Larry (Qianlin) Zhou / Regulatory Specialist E-mail : [email protected] Tel. : 346-260-3543

Regulatory Engineering Zebra Technologies Corporation 1 Zebra Plaza, | Holtsville, NY 11742 | 1.631.738.2400 phone | 1.631.627.7179 fax | www.zebra.com Date: May 24, 2024 Federal Communications Commission Office of Engineering and Technology Equipment Authorization Division 7435 Oakland Mills Road Columbia, MD 21046 Ref: FCC ID: UZ7MC3401 AUTHORIZATION LETTER We, the undersigned, hereby authorize Jones Tsai in Sporton International Inc. to act on our behalf in all manners relating to FCC application for equipment authorization, including signing of all documents relating to these matters. Any and all acts carried out by Jones Tsai in Sporton International Inc. on our behalf shall have the same effect as acts of our own. If you have any acknowledgement and response, please send it to Sporton International Inc. directly. Confidentiality Request Pursuant to the provisions of Sections 0.457 and 0.459 of Commission’s rules (47CFR§§0.457, 0.459), we are requesting the Commission to withhold the following attachment(s) as confidential document from public disclosure indefinitely.  Schematic Diagram  Block Diagram  Part List  Operational Description  Tune-up Procedure Above mentioned document contains detailed system and equipment description are considered as proprietary information in operation of the equipment. The public disclosure of above documents might be harmful to our company and would give competitor an unfair advantage in the market. In additional to above mentioned documents, pursuant to Public Notice DA 04-1705 of the Commission’ s policy, in order to comply with the marketing regulations in 47 CFT §2.803 and the importation rules in 47 CFR §2.1204, while ensuring that business sensitive information remains confidential until the actual marketing of newly authorized devices. We are requesting the commission to grant shot-term confidentiality request on the following attachment(s) for 180 days after the grant as outlined in Public Notice DA 04-1705. Regulatory Engineering Zebra Technologies Corporation 1 Zebra Plaza, | Holtsville, NY 11742 | 1.631.738.2400 phone | 1.631.627.7179 fax | www.zebra.com  Internal Photos  External Photos  Test Setup Photos  User Manual It is our understanding that all measurement test reports, FCC ID label format and correspondent during certification review process cannot be granted as confidential documents and those information will be available for public review once the grant of equipment authorization is issued. If you have any questions regarding this authorization, please contact me directly. Signature : _______________________________ Name and Job Title. : Larry (Qianlin) Zhou / Regulatory Specialist E-mail : [email protected] Tel. : 346-260-3543

Regulatory Engineering Zebra Technologies Corporation 1 Zebra Plaza, | Holtsville, NY 11742 | 1.631.738.2400 phone | 1.631.627.7179 fax | www.zebra.com Date: May 24, 2024 Federal Communications Commission Office of Engineering and Technology Equipment Authorization Division 7435 Oakland Mills Road Columbia, MD 21046 Ref: FCC ID: UZ7MC3401 AUTHORIZATION LETTER We, the undersigned, hereby authorize Jones Tsai in Sporton International Inc. to act on our behalf in all manners relating to FCC application for equipment authorization, including signing of all documents relating to these matters. Any and all acts carried out by Jones Tsai in Sporton International Inc. on our behalf shall have the same effect as acts of our own. If you have any acknowledgement and response, please send it to Sporton International Inc. directly. Confidentiality Request Pursuant to the provisions of Sections 0.457 and 0.459 of Commission’s rules (47CFR§§0.457, 0.459), we are requesting the Commission to withhold the following attachment(s) as confidential document from public disclosure indefinitely.  Schematic Diagram  Block Diagram  Part List  Operational Description  Tune-up Procedure Above mentioned document contains detailed system and equipment description are considered as proprietary information in operation of the equipment. The public disclosure of above documents might be harmful to our company and would give competitor an unfair advantage in the market. In additional to above mentioned documents, pursuant to Public Notice DA 04-1705 of the Commission’ s policy, in order to comply with the marketing regulations in 47 CFT §2.803 and the importation rules in 47 CFR §2.1204, while ensuring that business sensitive information remains confidential until the actual marketing of newly authorized devices. We are requesting the commission to grant shot-term confidentiality request on the following attachment(s) for 180 days after the grant as outlined in Public Notice DA 04-1705. Regulatory Engineering Zebra Technologies Corporation 1 Zebra Plaza, | Holtsville, NY 11742 | 1.631.738.2400 phone | 1.631.627.7179 fax | www.zebra.com  Internal Photos  External Photos  Test Setup Photos  User Manual It is our understanding that all measurement test reports, FCC ID label format and correspondent during certification review process cannot be granted as confidential documents and those information will be available for public review once the grant of equipment authorization is issued. If you have any questions regarding this authorization, please contact me directly. Signature : _______________________________ Name and Job Title. : Larry (Qianlin) Zhou / Regulatory Specialist E-mail : [email protected] Tel. : 346-260-3543

A1 1 12/16’23 12/16’23 Yuanhao UG/CVS/SHD1/KSED/MDE 1/1mm 0.2 Siming 59-478519-01 2B-081068 Product label for MC3401 NA SKU 1. (S)S/N: Serial Number: YYDDDZZZZPSSSS Serial Number : from 0001 to 9999. The start at 0001 at the beginning of every day. Julian day of the year from 001 to 365. Year (2005~2009=05~09 ; 2010,2011...=10,11...) All Pre EV or Prototype units : P; All EV units : E ; All DV units : D MV and Production units back to normal format : 0 to 9. Bar code data : SYYDDDZZZZPSSSS (Use 128/code B/Narrow bar width dots is 4) 6 2. 3. P/N:XXXXXXXXXXXXX Please refer PDM Page2 “Customer P/N” MADE IN XXXXXX XX P/N: XXXXXXXXXXXXXXXXXXXX MFD: DDMMMYY (S)S/N: YYDDDZZZZPSSSS BT : XXXXXXXXXXXX WLAN: XXXXXXXXXXXX XXXXXXXXXXXX MODEL : MC3401 ZEBRA TECHNOLOGIES CORP.HOLTSVILLE, NY 11742 Pats.: ip.zebra.com Wolverine 4. WLAN: XXXXXXXXXXXX EX: WLAN: 123456789012 IMEI1: XXXXXXXXXXXXXXX EX: IMEI1: 123456789012345 BT: XXXXXXXXXXXXXXX EX: BT: 123456789012 IMEI2: XXXXXXXXXXXXXXX EX: IMEI2: 123456789012345 7.00 mm I.T.E. E177793 IC: 109AN-MC3401 FCC ID: UZ7MC3401 CAN ICES-3(B)/NMB-3(B) 7.00 mm 5230 5V 2.5 A Plant code:5251 for USI Vietnam. Plant code:5201 for USI Taiwan. Plant code:5211 for USI Shanghai. Plant code:5230 for USI Kunshan. 5. MADE IN XXXXXX XX TAIWAN NK CHINA KS VIETNAM VN 3M7815 UL File: MH47378, Company name: SHANGHAI BECORE PAPER MANUFACTURING CO LTD UL Category code: PGJI2,HT-POLYESTER-200, UL Marking:SHANGHAI BECORE PAPER MANUFACTURING CO LTD. HT-POLYESTER-200, zebra 5095

Model Name: MC3401 Label stick on backside of terminal. Spec label

TEL : 886-3-327-3456 Page : F1 of F3 FAX : 886-3-328-4978 FCC SAR TEST REPORT Report No. :FA443061 Appendix F. Supplemental SAR Tests Results SAR test result 1. The test data is selected according to the worst case SAR configuration per cellular technology. 2. The test data is to demonstrate the device is in compliance with FCC requirements at 25mm when all power reduction mechanisms are OFF. The worst case body SAR at 10mm was used for simultaneous transmission SAR analysis since they are more conservative than the 25mm SAR. Band Mode Test Position Gap (mm) Antenna SKU Brick / Gun Type Battery Power State Ch. Freq. (MHz) Average Power (dBm) Tune-Up Limit (dBm) Duty Cycle % Duty Cycle Scaling Factor Power Drift (dB) Measured 1g SAR (W/kg) Reported 1g SAR (W/kg) Measured APD (W/m^2) Reported APD (W/m^2) WLAN2.4GHz 802.11b 1Mbps Right Side 25mm Ant 6+7(6) SKU 13 Brick 1 Index 0 1 2412 19.98 20.50 97.87 1.022 0.03 0.185 0.213 0.000 WLAN2.4GHz 802.11b 1Mbps Right Side 25mm Ant 6+7(6) SKU 9 Gun 1 Index 0 1 2412 19.98 20.50 97.87 1.022 -0.04 0.100 0.115 0.000 WLAN5GHz 802.11a 6Mbps Left Side 25mm Ant 6+7(6) SKU 13 Brick 1 Index 0 165 5825 21.20 22.00 100 1.000 -0.08 0.855 1.028 0.000 WLAN5GHz 802.11a 6Mbps Left Side 25mm Ant 6+7(6) SKU 9 Gun 1 Index 0 165 5825 21.20 22.00 100 1.000 -0.06 0.865 1.040 0.000 WLAN6GHz 802.11ax-HE160 MCS0 Left Side 25mm Ant 6+7(7) SKU 13 Brick 1 Index 0 47 6185 16.70 17.00 98.19 1.018 -0.07 0.305 0.333 2.830 3.087 WLAN6GHz 802.11ax-HE160 MCS0 Left Side 25mm Ant 6+7(7) SKU 9 Gun 1 Index 0 47 6185 16.70 17.00 98.19 1.018 -0.17 0.332 0.362 3.080 3.360 TEL : 886-3-327-3456 Page : F2 of F3 FAX : 886-3-328-4978 FCC SAR TEST REPORT Report No. :FA443061 Appendix F. Power reduction mechanism verification 1. Motion Time vs Power verification a) Body Detect mechanism will be performed for the in-hand and on a stationary object (placed on a table). b) Verify the functionality of the motion sensor by measuring the output power in the following steps. Figure 1 Illustration of the procedure for the validation of the power reduction The device is embedded with motion sensors only, no proximity sensors are installed. 1. Placed on a table: Make the DUT transmit with the maximum output power by using a base station simulator. a) Confirm that motion sensor is not triggered by letting the DUT remain stationary with no movements for the period T relax for the motion sensor to reach stationary state. b) Record P step1 (high power) 2. In-hand: Move the DUT to trigger the motion sensor. Apply the motion of the DUT with respect to movements in intended and reasonably foreseeable use conditions of the DUT. a) Record P step2 (low power) 3. For the validation of T relax , wait a time period T 1 > T relax and confirm DUT restores to high power (P step1 ). 4. Move the DUT to trigger the motion sensor. 5. Move DUT within T relax to ensure T relax resets when DUT is in motion. DUT can be moved once or twice within T relax , (after time periods T 2a and T 2b in Figure 1.) followed by waiting for a time period greater than T relax (time period T 2c in Figure 1.) for DUT to restore high power. The total time duration of this step is T 2 , and the power during the whole period T 2 shall be reduced (low power – P step2 ). TEL : 886-3-327-3456 Page : F3 of F3 FAX : 886-3-328-4978 FCC SAR TEST REPORT Report No. :FA443061 Exposure Condition Output Power (data connection) (dBm) Stationary Placed on a table In hand Stationary Placed on a table In hand Stationary Placed on a table Power state Full Power P step1 Low Power P step2 Full Power P step1 & T 1 > T relax Low Power P step2 & T 2a ＜ T relax Low Power P step2 & T 2b ＜ T relax Full Power P step1 & T 2c > T relax Wireless technology Antenna Measured Max. Tune-up Measured Max. Tune-up Measured Max. Tune-up Measured Max. Tune-up Measured Max. Tune-up Measured Max. Tune-up 802.11a 6Mbps ,CH116 (Ant6+7) Ant 6 17.8 19.0± 1.5dB 17.6 17.0± 1.5dB 17.9 19.0± 1.5dB 17.5 17.0± 1.5dB 17.6 17.0± 1.5dB 17.9 19.0± 1.5dB (Ant6+7) Ant 7 17.9 19.0± 1.5dB 17.5 17.0± 1.5dB 17.9 19.0± 1.5dB 17.5 17.0± 1.5dB 17.5 17.0± 1.5dB 17.9 19.0± 1.5dB Exposure Condition Output Power (data connection) (dBm) Display on Stationary Placed on a table Display off Power state Full Power P step1 Low Power P step2 Wireless technology Antenna Measured Max. Tune-up Measured Max. Tune-up 802.11a 6Mbps ,CH116 (Ant6+7)Ant 6 17.8 19.0±1.5dB 17.6 17.0±1.5dB (Ant6+7)Ant 7 17.9 19.0±1.5dB 17.5 17.0±1.5dB

SP ORTON INTERNATIONAL INC. T EL : 886-3-327-3456 FAX : 886-3-328-4978 D2450V2, serial no. 736 Extended Dipole Calibrations If dipoles are verified in return loss (<-20dB, within 20% of prior calibration), and in impedance (within 5 ohm of prior calibration), the annual calibration is not necessary and the calibration interval can be extended. <Justification of the extended calibration> D2450V2 – serial no. 736 2450M HZ Da te of Measurement Re turn-Loss (dB) De lta (%) Re al Impedance (ohm) De lta (ohm) I maginary Impedance (ohm) De lta (ohm) 08.17.2021 (C al. Report) -24.29755.295 3.6377 08.16.2022 (ex tended) -28.76118.37 51.401 -3.8943.556 -0.0817 08.15.2023 (ex tended) -28.48317.23 51.239 -4.0563.496 -0.1417 T he return loss is < -20dB, within 20% of prior calibration; the impedance is within 5 ohm of prior calibration. Therefore the verification result should support extended calibration. SPORTON INTERNATIONAL INC. TEL : 886-3-327-3456 FAX : 886-3-328-4978 <Dipole Verification Data> - D2450 V2, serial no. 736 (Data of Measurement : 08.16.2022) 2450 MHz - Head SPORTON INTERNATIONAL INC. TEL : 886-3-327-3456 FAX : 886-3-328-4978 <Dipole Verification Data> - D2450V2, serial no. 736 (Data of Measurement : 08.15.2023) D2450V2 MHz - Head SPORTON INTERNATIONAL INC. TEL : 886-3-327-3456 FAX : 886-3-328-4978 D2450V2, serial no. 929 Extended Dipole Calibrations If dipoles are verified in return loss (<-20dB, within 20% of prior calibration), and in impedance (within 5 ohm of prior calibration), the annual calibration is not necessary and the calibration interval can be extended. <Justification of the extended calibration> D2450V2 – serial no. 929 2450MHZ Date of Measurement Return-Loss (dB) Delta (%) Real Impedance (ohm) Delta (ohm) Imaginary Impedance (ohm) Delta (ohm) 11.21.2022 (Cal. Report) -25.5 52.9 4.7 11.20.2023 (extended) -25.9 1.57 52.3 -0.6 4.8 0.1 The return loss is < -20dB, within 20% of prior calibration; the impedance is within 5 ohm of prior calibration. Therefore the verification result should support extended calibration. SPORTON INTERNATIONAL INC. TEL : 886-3-327-3456 FAX : 886-3-328-4978 <Dipole Verification Data> - D2450 V2, serial no. 929 (Data of Measurement : 11.20.2023) 2450MHz - Head SPORTON INTERNATIONAL INC. TEL : 886-3-327-3456 FAX : 886-3-328-4978 D5000V2, serial no. 1006 Extended Dipole Calibrations If dipoles are verified in return loss (<-20dB, within 20% of prior calibration), and in impedance (within 5 ohm of prior calibration), the annual calibration is not necessary and the calibration interval can be extended. <Justification of the extended calibration> D5000V2 – serial no. 1006 5250MHZ Date of Measurement Return-Loss (dB) Delta (%) Real Impedance (ohm) Delta (ohm) Imaginary Impedance (ohm) Delta (ohm) 05.25.2023 (Cal. Report) -21.6 54.4 -7.5 05.24.2024 (extended) -19.7 -8.80 53.1 -1.3 -10.0 -2.5 5600MHZ Date of Measurement Return-Loss (dB) Delta (%) Real Impedance (ohm) Delta (ohm) Imaginary Impedance (ohm) Delta (ohm) 05.25.2023 (Cal. Report) -20.5 57.1 -7.3 05.24.2024 (extended) -22.9 11.71 55.0 -2.1 -6.0 1.3 5750MHZ Date of Measurement Return-Loss (dB) Delta (%) Real Impedance (ohm) Delta (ohm) Imaginary Impedance (ohm) Delta (ohm) 05.25.2023 (Cal. Report) -20.8 59.1 4.1 05.24.2024 (extended) -21.2 1.92 59.6 0.5 0.5 -3.6 5850MHZ Date of Measurement Return-Loss (dB) Delta (%) Real Impedance (ohm) Delta (ohm) Imaginary Impedance (ohm) Delta (ohm) 05.25.2023 (Cal. Report) -31.4 52.7 0.8 05.24.2024 (extended) -27.7 -11.78 55.4 2.7 0.1 -0.7 The return loss is < -20dB, within 20% of prior calibration; the impedance is within 5 ohm of prior calibration. Therefore the verification result should support extended calibration. SPORTON INTERNATIONAL INC. TEL : 886-3-327-3456 FAX : 886-3-328-4978 <Dipole Verification Data> - D5000 V2, serial no. 1006 (Data of Measurement : 05.24.2024) 5000MHz - Head SPORT ON INTERNATIONA L I NC. TE L : 886-3-327-3456 FA X : 886 -3-328-497 8 CLA13, serial no. 1022 Extended Dipole Calibrations If dipoles are verified in return loss (<-20dB, within 20% of prior calibration), and in impedance (within 5 ohm of prior calibration), the annual calibration is not necessary and the calibration interval can be extended. <Justification of the extended calibration> CLA13 – serial no. 1022 13MHZ Date of Measurement Return-Loss (dB) Delta (%) Real Impedance (ohm) Delta (ohm) Imaginary Impedance (ohm) Delta (ohm) 09.01.2022 (Cal. Report) -25.51848.364 4.9544 08.3 1.2023 (extended) -24.882 -2.4950.308 1.944 5.7239 0.7695 The return loss is < -20dB, within 20% of prior calibration; the impedance is within 5 ohm of prior calibration. Therefore the verification result should support extended calibration. SPORTON INTERNATIONAL INC. TEL : 886-3-327-3456 FAX : 886-3-328-4978 <Dipole Verification Data> - CLA13, serial no. 1022 (Data of Measurement : 08.31.2023) 13 MHz - Head

Scans Setup Scan Type5G Scan Grid Extents [mm]80.0 x 80.0 Grid Steps [lambda]0.0625 x 0.0625 Sensor Surface [mm]2.0 Measurement Results Date Avg. Area [cm 2 ] psPDn+ [W/m 2 ] psPDtot+ [W/m 2 ] H max [A/m] E max [V/m] max (Stot) [W/m 2 ] Power Drift [dB] 2024-05-15 4.00 3.72 4.31 0.153 51.8 7.04 0.03 IPDn Measurement Report for Device Device Under Test Properties Model, ManufacturerDimensions [mm]Software VersionDUT Type Device,205.0 x 75.0 x 36.03.2.0.1840Phone Exposure Conditions Phantom SectionPosition, Test Distance [mm]Frequency [MHz]Conversion Factor 5GEDGE LEFT, 2.006985.01.0 Hardware Setup PhantomMediumProbe, Calibration DateDAE, Calibration Date mmWave - 1044Air -EUmmWV4 - SN9461_F1-55GHz, 2023-10-12DAE4 Sn854, 2023-08-17

Date: 2024-05-17 #01_WLAN2.4GHz_802.11b 1Mbps_Right Side_10mm_Ch1 Communication System: 802.11b; Frequency: 2412.000 MHz Medium: HSL_2450_240517 Medium parameters used: f= 2412.000 MHz; σ= 1.74 S/m; ε r = 39.0 Ambient Temperature: 23.4°C; Liquid Temperature: 22.4°C DASY8 Configuration: - Probe: EX3DV4 - SN7822; ConvF(6.89, 6.89, 7.21); Calibrated: 2023-08-02 - Sensor-Surface: 1.4 mm - Electronics: DAE4ip Sn1823; Calibrated: 2023-07-31 - Phantom: ELI V8.0 (20deg probe tilt); Serial: 2211; Section: Flat - Measurement Software: 16.2.4.2524 - UID: WLAN, 10012-CAB Area Scan (100.0 mm x 160.0 mm): Measurement Grid: 10.0 mm x 10.0 mm SAR (1g) = 0.471 W/kg; SAR (10g) = 0.237 W/kg; Zoom Scan (30.0 mm x 30.0 mm x 30.0 mm): Measurement Grid: 5.0 mm x 5.0 mm x 1.5 mm Power Drift = 0.08 dB SAR (1g) = 0.502 W/kg; SAR (8g) = 0.274 W/kg; SAR (10g) = 0.251 W/kg Smallest distance from peaks to all points 3 dB below = 12.6 mm Ratio of SAR at M2 to SAR at M1 = 76.3 % Date: 2024-05-28 #02_Bluetooth_1Mbps_Right Side_10mm_Ch78 Communication System: Bluetooth; Frequency: 2480.000 MHz Medium: HSL_2450_240528 Medium parameters used: f= 2480.000 MHz; σ= 1.85 S/m; ε r = 39.5 Ambient Temperature: 23.5°C; Liquid Temperature: 22.5°C DASY8 Configuration: - Probe: EX3DV4 - SN7822; ConvF(6.89, 6.89, 7.21); Calibrated: 2023-08-02 - Sensor-Surface: 1.4 mm - Electronics: DAE4ip Sn1823; Calibrated: 2023-07-31 - Phantom: ELI V8.0 (20deg probe tilt); Serial: 2211; Section: Flat - Measurement Software: 16.2.4.2524 - UID: Bluetooth, 10030-CAA Area Scan (120.0 mm x 120.0 mm): Measurement Grid: 10.0 mm x 10.0 mm SAR (1g) = 0.010 W/kg; SAR (10g) = 0.005 W/kg; Zoom Scan (30.0 mm x 30.0 mm x 30.0 mm): Measurement Grid: 5.0 mm x 5.0 mm x 1.5 mm Power Drift = 0.07 dB SAR (1g) = 0.012 W/kg; SAR (8g) = 0.006 W/kg; SAR (10g) = 0.005 W/kg Smallest distance from peaks to all points 3 dB below = 9.5 mm Ratio of SAR at M2 to SAR at M1 = 90.0 % Date: 2024-05-17 #03_WLAN2.4GHz_802.11b 1Mbps_Front_0mm_Ch1 Communication System: 802.11b; Frequency: 2412.000 MHz Medium: HSL_2450_240517 Medium parameters used: f= 2412.000 MHz; σ= 1.74 S/m; ε r = 39.0 Ambient Temperature: 23.4°C; Liquid Temperature: 22.4°C DASY8 Configuration: - Probe: EX3DV4 - SN7822; ConvF(6.89, 6.89, 7.21); Calibrated: 2023-08-02 - Sensor-Surface: 1.4 mm - Electronics: DAE4ip Sn1823; Calibrated: 2023-07-31 - Phantom: ELI V8.0 (20deg probe tilt); Serial: 2211; Section: Flat - Measurement Software: 16.2.4.2524 - UID: WLAN, 10012-CAB Area Scan (120.0 mm x 120.0 mm): Measurement Grid: 10.0 mm x 10.0 mm SAR (1g) = 0.270 W/kg; SAR (10g) = 0.134 W/kg; Zoom Scan (30.0 mm x 30.0 mm x 30.0 mm): Measurement Grid: 5.0 mm x 5.0 mm x 1.5 mm Power Drift = -0.01 dB SAR (1g) = 0.286 W/kg; SAR (8g) = 0.154 W/kg; SAR (10g) = 0.142 W/kg Smallest distance from peaks to all points 3 dB below = 7.7 mm Ratio of SAR at M2 to SAR at M1 = 78.5 % Date: 2024-05-15 #04_WLAN5GHz_802.11n HT40 MCS0_Left Side_0mm_Ch54 Communication System: 802.11n; Frequency: 5270.000 MHz Medium: HSL_5250_240515 Medium parameters used: f= 5270.000 MHz; σ= 4.71 S/m; ε r = 35.5 Ambient Temperature: 23.5°C; Liquid Temperature: 22.5°C DASY8 Configuration: - Probe: EX3DV4 - SN7822; ConvF(5.38, 5.34, 5.57); Calibrated: 2023-08-02 - Sensor-Surface: 1.4 mm - Electronics: DAE4ip Sn1823; Calibrated: 2023-07-31 - Phantom: ELI V8.0 (20deg probe tilt); Serial: 2211; Section: Flat - Measurement Software: 16.2.4.2524 - UID: WLAN, 10599-AAD Area Scan (100.0 mm x 100.0 mm): Measurement Grid: 10.0 mm x 10.0 mm SAR (1g) = 0.965 W/kg; SAR (10g) = 0.411 W/kg; Zoom Scan (22.0 mm x 22.0 mm x 22.0 mm): Measurement Grid: 4.0 mm x 4.0 mm x 1.4 mm Power Drift = 0.00 dB SAR (1g) = 0.974 W/kg; SAR (8g) = 0.459 W/kg; SAR (10g) = 0.414 W/kg Smallest distance from peaks to all points 3 dB below = > 11.0 mm Ratio of SAR at M2 to SAR at M1 = 64.7 % Date: 2024-05-15 #05_WLAN5GHz_802.11ac VHT80 MCS0_Left Side_0mm_Ch138 Communication System: 802.11ac; Frequency: 5690.000 MHz Medium: HSL_5600_240515 Medium parameters used: f= 5690.000 MHz; σ= 5.23 S/m; ε r = 36.2 Ambient Temperature: 23.5°C; Liquid Temperature: 22.5°C DASY8 Configuration: - Probe: EX3DV4 - SN7822; ConvF(4.68, 4.58, 4.85); Calibrated: 2023-08-02 - Sensor-Surface: 1.4 mm - Electronics: DAE4ip Sn1823; Calibrated: 2023-07-31 - Phantom: ELI V8.0 (20deg probe tilt); Serial: 2211; Section: Flat - Measurement Software: 16.2.4.2524 - UID: WLAN, 10544-AAD Area Scan (100.0 mm x 100.0 mm): Measurement Grid: 10.0 mm x 10.0 mm SAR (1g) = 0.916 W/kg; SAR (10g) = 0.386 W/kg; Zoom Scan (22.0 mm x 22.0 mm x 22.0 mm): Measurement Grid: 4.0 mm x 4.0 mm x 1.4 mm Power Drift = 0.04 dB SAR (1g) = 0.946 W/kg; SAR (8g) = 0.438 W/kg; SAR (10g) = 0.396 W/kg Smallest distance from peaks to all points 3 dB below = 17.7 mm Ratio of SAR at M2 to SAR at M1 = 61.8 % Date: 2024-05-16 #06_WLAN5GHz_802.11ac VHT80 MCS0_Left Side_0mm_Ch155 Communication System: 802.11ac; Frequency: 5775.000 MHz Medium: HSL_5750_240516 Medium parameters used: f= 5775.000 MHz; σ= 5.34 S/m; ε r = 36.1 Ambient Temperature: 23.5°C; Liquid Temperature: 22.5°C DASY8 Configuration: - Probe: EX3DV4 - SN7822; ConvF(4.68, 4.58, 4.85); Calibrated: 2023-08-02 - Sensor-Surface: 1.4 mm - Electronics: DAE4ip Sn1823; Calibrated: 2023-07-31 - Phantom: ELI V8.0 (20deg probe tilt); Serial: 2211; Section: Flat - Measurement Software: 16.2.4.2524 - UID: WLAN, 10544-AAD Area Scan (120.0 mm x 120.0 mm): Measurement Grid: 10.0 mm x 10.0 mm SAR (1g) = 1.02 W/kg; SAR (10g) = 0.421 W/kg; Zoom Scan (22.0 mm x 22.0 mm x 22.0 mm): Measurement Grid: 4.0 mm x 4.0 mm x 1.4 mm Power Drift = 0.01 dB SAR (1g) = 1.03 W/kg; SAR (8g) = 0.470 W/kg; SAR (10g) = 0.424 W/kg Smallest distance from peaks to all points 3 dB below = 17.2 mm Ratio of SAR at M2 to SAR at M1 = 60.4 % Date: 2024-05-18 #07_WLAN6GHz_802.11ax-HE160 MCS0_Left Side_0mm_Ch143 Communication System: 802.11ax ; Frequency: 6665.000 MHz Medium: HSL_6500_240518 Medium parameters used: f= 6665.000 MHz; σ= 6.30 S/m; ε r = 34.2 Ambient T…

Text truncated - open the document above for the full version.

Scans Setup Scan Type5G Scan Grid Extents [mm]120.0 x 120.0 Grid Steps [lambda]0.25 x 0.25 Sensor Surface [mm]10.0 Measurement Results Date2024-05-15 Avg. Area [cm 2 ] 4.00 psPDn+ [W/m 2 ] 57.6 psPDtot+ [W/m 2 ] 57.9 H max [A/m]0.416 E max [V/m]159 max (Stot) [W/m 2 ] 65.4 Power Drift [dB]0.00 Measurement Report for Device Device Under Test Properties Model, ManufacturerDimensions [mm]Software VersionDUT Type Device,100.0 x 100.0 x 172.03.2.0.18405G Verification Source Exposure Conditions Phantom SectionPosition, Test Distance [mm]Frequency [MHz]Conversion Factor 5GFRONT, 10.0010000.01.0 Hardware Setup PhantomMediumProbe, Calibration DateDAE, Calibration Date mmWave - 1044Air -EUmmWV4 - SN9461_F1-55GHz, 2023-10-12DAE4 Sn854, 2023-08-17 Scans Setup Scan Type5G Scan Grid Extents [mm]120.0 x 120.0 Grid Steps [lambda]0.25 x 0.25 Sensor Surface [mm]10.0 Measurement Results Date2024-05-27 Avg. Area [cm 2 ] 4.00 psPDn+ [W/m 2 ] 59.6 psPDtot+ [W/m 2 ] 59.8 H max [A/m]0.420 E max [V/m]160 max (Stot) [W/m 2 ] 66.0 Power Drift [dB]-0.02 Measurement Report for Device Device Under Test Properties Model, ManufacturerDimensions [mm]Software VersionDUT Type Device,100.0 x 100.0 x 172.03.2.0.18405G Verification Source Exposure Conditions Phantom SectionPosition, Test Distance [mm]Frequency [MHz]Conversion Factor 5GFRONT, 10.0010000.01.0 Hardware Setup PhantomMediumProbe, Calibration DateDAE, Calibration Date mmWave - 1044Air -EUmmWV3 - SN9424_F1-55GHz, 2024-03-12DAE4ip Sn1823, 2023-07-31

Test Laboratory: Sporton International Inc. SAR/HAC Testing Lab Date: 2024/6/4 System Check_Head_13MHz DUT: CLA13-1022 Communication System: CW; Frequency: 13 MHz;Duty Cycle: 1:1 Medium: HSL_13_240604 Medium parameters used : f = 13 MHz; σ = 0.757 S/m; ε r = 54.635; ρ = 1000 kg/m 3 Ambient Temperature：23.6 °C; Liquid Temperature：22.6 °C DASY5 Configuration: - Probe: EX3DV4 - SN3642;ConvF(14.84, 14.84, 14.84…

Text truncated - open the document above for the full version.