UZ7MPM100Mobile Payment Module

MPM-100 MOBILE PAYMENT MODULE QUICK REFERENCE GUIDE QRG.fm Page 1 Friday, October 14, 2011 3:24 PM PRELIMINARY 2MPM-100 Motorola reserves the right to make changes to any product to improve reliability, function, or design. Motorola does not assume any product liability arising out of, or in connection with, the application or use of any product, circuit, or application described herein. No license is granted, either expressly or by implication, estoppel, or otherwise under any patent right or patent, covering or relating to any combination, system, apparatus, machine, material, method, or process in which Motorola products might be used. An implied license exists only for equipment, circuits, and subsystems contained in Motorola products. Service Information If you have a problem using the equipment, contact your facility’s Technical or Systems Support. If there is a problem with the equipment, they will contact the Motorola Enterprise Mobility Support at: http://www.motorola.com/enterprisemobility/customersupport. For the latest version of this guide go to: http://supportcentral.motorola.com. QRG.fm Page 2 Friday, October 14, 2011 3:24 PM PRELIMINARY Quick Reference Guide3 Introduction This Quick Reference Guide explains how to setup, use and maintain the MPM-100 Mobile Payment Module. Unpacking Carefully remove all protective material from around the device and save the shipping container for later storage and shipping. Verify that you received all equipment listed below: • MPM-100 • Lithium-ion battery (2400 mAh) • Battery door • Quick Start Guide. Inspect the equipment for damage. If you are missing any equipment or if you find any damaged equipment, contact the Motorola Enterprise Mobility Support immediately. See Service Information for contact information. QRG.fm Page 3 Friday, October 14, 2011 3:24 PM PRELIMINARY 4MPM-100 Features LED StateDescription Contactless Notification LEDs OnDuring a Contactless transaction, LEDs light from left to right indicating transaction is in process. Power Flashing GreenMPM-100 is in sleep mode. Slow Flashing RedBattery is low. Bluetooth LED Power LED Battery Door Power Button USB Port Smart Card Slot Keypad Mag Stripe Slot Contactless Area Display Contactless Notification LEDs Charging Contacts Bluetooth MAC Address Bar Code QRG.fm Page 4 Friday, October 14, 2011 3:24 PM PRELIMINARY Quick Reference Guide5 Keypad Use the numeric keypad for entering data. Fast Flashing RedBattery voltage is low. Slow Flashing RedBattery voltage is very low. Slow Flashing OrangeBattery is charging. Solid OrangeA charging timer fault occurred. Solid GreenFIrmware upgrade in process. Bluetooth Single Blue FlashActive SPP connection with mobile device. Double Blue FlashAfter a power on, the MPM-100 is resuming pair relationship with mobile device. OffMPM-100 is in discoverable mode. LED StateDescription Numeric Keys Cancels the current Transaction Clears the entered data Submits the entered data QRG.fm Page 5 Friday, October 14, 2011 3:24 PM PRELIMINARY 6MPM-100 Getting Started To start using the MPM-100, install one or two Security Access Module (SAM) cards (if required), install the battery and then charge the MPM-100. Installing SAM Cards To install a SAM card: 1.Place the MPM face-down on a flat surface. 2.Lift the manufacturing label. 3.Slide a SAM card holder to the right to unlock and then lift. 4.Insert the SAM card into the holder in the orientation shown above. 5.Close the SAM card holder. 6.Slide the SAM card holder to the left to lock. 7.Repeat for the second SAM card, if required. 8.Place the label over the SAM card holders. NOTEAn SAM card is not required for all applications. If using one SAM card, place the card in either holder. QRG.fm Page 6 Friday, October 14, 2011 3:24 PM PRELIMINARY Quick Reference Guide7 Installing the Battery 1.Place the battery, contacts first, into the battery compartment. 2.Ensure that the battery is laying flat in the compartment. 3.Align the battery door with the battery compartment. 4.Secure the battery door to the MPM-100 using four screws. Contacts QRG.fm Page 7 Friday, October 14, 2011 3:24 PM PRELIMINARY 8MPM-100 Charging the MPM-100 Using Cradle Place the MPM-100 into a slot in the cradle. Ensure that the MPM-100 is seated properly. Failure to do so can cause the MPM-100 to not charge properly. The MPM-100 Power LED indicates that the MPM-100 is charging. Using USB Cable or Power Supply To charge the MPM-100 using a USB cable: 1.Connect the micro USB A connector of the USB cable to the USB port on the MPM-100. 2.Connect other end of the USB cable to a host computer or to the power supply. QRG.fm Page 8 Friday, October 14, 2011 3:24 PM PRELIMINARY Quick Reference Guide9 Turning On / Off To turn on the MPM, press and hold the Power button until Verix Terminal Manager2 appears on the display. To turn off the MPM press and hold either the Power button or the Cancel key until SHUTTING DOWN appears on the display. Bluetooth Communication To use the MPM-100 with a mobile device, pair the mobile device and the MPM. NOTEBluetooth pairing and communication may vary depending upon the mobile device being used. Refer to the mobile device’s User Guide for more information. If the mobile device supports the Scan and Pair Bluetooth pairing feature, scan the Bluetooth MAC Address bar code on the back of the MPM-100 to pair the mobile device and the MPM-100. QRG.fm Page 9 Friday, October 14, 2011 3:24 PM PRELIMINARY 10MPM-100 1.On the mobile device, enable Bluetooth. 2.Turn on the MPM-100. The Bluetooth LED flashes blue. 3.On the mobile device, perform a Bluetooth discovery. 4.Select the MPM-100 (VFI-PWN-sRDA-xx). 5.Enter PIN (0000). 6.Complete connection. Magnetic Stripe Transactions Launch a transaction application on the mobile device and initiate a credit or debit transaction. On the MPM-100, swipe the credit or debit card through the magnetic stripe reader (MSR) slot, orienting the magnetic stripe as shown. For credit transaction…

Text truncated - open the document above for the full version.

December 30, 2011 DE C L A R A T I O N L E T T E R Federal Communications Commission 7435 Oakland Mills Road Columbia MD 21046 Subject: Declaration letter for label requirement FCC ID: UZ7MPM100 The label is permanent affixed in the battery compartment, and the EUT will be selling to market without the battery installed. The users can see the label during the battery installation process. The battery cover can be opened without any special tools. Please don’t hesitate to contact us, if you have any question(s). Thank you! ---------------------------------------------------------------- Andrew Ho Regulatory Manager Motorola Solutions - Regulatory Tel: +65 6643 9326 Fax: +65-6483 2909 E-mail: [email protected]

Regulatory Engineering Motorola Solutions, Inc. O n e Mo t o r o l a P l a za , | Ho l t s vi l l e , NY 1 1 7 4 2 | 1.631.738.2400 phone | 1.631.627.7179 fax | www.m otorola.com Date: 31 st October, 2011 Federal Communications Commission Authorization and Evaluation Division Confidentiality Request FCC ID: UZ7MPM100 Pursuant to Sections 0.457 and 0.459 of the Commission’s Rules, the Applicant hereby requests confidential treatment of information accompanying this Application as outlined below: Schematics Block Diagram Parts List Operational Description The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the Applicant and provide unjustified benefits to its competitors. The Applicant understands that pursuant to Rule 0.457, disclosure of this Application and all accompanying documentation will not be made before the date of the Grant for this application. Yours sincerely, ________________________________ Andrew Ho Regulatory Manager Motorola Solutions - Regulatory Tel: +65 6643 9326 Email: [email protected]

Regulatory Engineering Motorola Solutions, Inc. O n e Mo t o r o l a P l a za , | Ho l t s vi l l e , NY 1 1 7 4 2 | 1.631.738.2400 phone | 1.631.627.7179 fax | www.m otorola.com Date: 31 st October, 2011 P O W E R O F A T T O R N E Y To whom it may concern, Please be notified that we, Motorola Solutions, Inc. have assigned Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch (BV CPS Taoyuan) of Taiwan, as our agent. Any and all acts carried out by Sporton International Inc., on the matters of relating to all processes required in the FCC matters and any communication needed with the national authority, shall have the same legal authority as acts on our own behalf. This authorization is limited to the following product: FCC ID: UZ7MPM100 Please send any acknowledgement or response to Bureau Veritas Consumer Products Services (H.K.) Ltd. directly. Should you have any questions or comments regarding this matter, please don’t hesitate to contact us. Yours sincerely, ________________________________ Andrew Ho Regulatory Manager Motorola Solutions - Regulatory Tel: +65 6643 9326 Email: [email protected]

Regulatory Engineering Motorola Solutions, Inc. One Motorola Plaza, | Holtsville, NY 11742 | 1.631.738.2400 phone | 1.631.627.7179 fax | www.motorola.com November 10, 2011 Federal Communications Commission Office of Engineering and Technology Equipment Authorization Division 7345 Oakland Mills Road Columbia MD 21046 Subject: Letter of Authorization To the Commission: I, the undersigned, grant authorization for Andrew Ho to sign the submissions to the FCC for the Motorola Payment Module sold under Model Number: MPM-100 and certified by the FCC under FCC ID: UZ7MPM100. Respectfully, Mark S. Luksich DMTS, Regulatory Engineering 631-738-5134 [email protected]

Page 1 CONSTRUCTION PHOTOS OF EUT Page 2 Page 3 Page 4 Page 5 Page 6 Page 7

0560 35.1mm 4 9 . 1 m m SIGNA TURES REV.DWG.NO.SIZE TITLE DATE SCALE: SHEET DWN. ENG. CHK. OF XXX ECO# CXXXXX 10/12/11 ALLEN_K2 LABEL VX600 BLUETOOTH MPM-100 PROD ID ARTWORK, LBL087-261-02-AW XXX A4 2:1 VICTORIA_L1 ALLEN_K2 ALLEN_K2 10/12/11 10/12/11 10/12/11 THIS DOCUMENT IS THE PROPERTY OF VERIFONE, AND CONTAINS VERIFONE'S CONFIDENTIAL AND PROPRIETARY INFORMATION IN CONSIDERATION OF VERIFONE'S DISCLOSURE OF THIS DOCUMENT TO YOU, YOU AGREE THAT NEITHER IT, NOR THE INFORMATION CONTAINED THEREIN SHALL BE DISCLOSED TO OTHERS OR DUPLICATED, IN WHOLE OR IN PART, OR USED FOR ANY PURPOSES OTHER THAN AGREED TO BY VERIFONE, WITHOUT EXPRESS WRITTEN CONSENT OF VERIFONE. THIS ARTWORK IS THE PROPER TY OF VERIFONE. HANDLE WITH CARE AND RETURN TO VERIFONE VERY SOON AFTER USE. UNLESS OTHERWISE SPECIFIED, DIMENSIONS ARE IN MILLIMETERS. 11 REV.DESCRIPTIONDATEAPPROVED REVISIONS NOTES: 1.BACKGROUND:BLACK 2.LOGO & TEXT: PANTONE PMS COOL GRAY 9C I.T.E. 8J09 I.T.E. E132144 R MODEL:MPM-100 5V 1A FCC ID:UZ7MPM100 ICES/NMB-003 CLASS B IC:109AN-MPM100 P/N:MPM-100

Page 8 Page 9 Page 10 Page 11 Page 12 Page 13 Page 14 Page 15 Page 16

Report No.: SA110922C14 Report Format Version 4.0.0 1 RF EXPOSURE REPORT (FOR BLUETOOTH) REPORT NO.: SA110922C14 MODEL NO.: MPM-100 FCC ID: UZ7MPM100 RECEIVED: Sep. 22, 2011 TESTED: Oct. 01 ~ Oct. 24, 2011 ISSUED: Oct. 27, 2011 APPLICANT: Motorola Solutions, Inc. ADDRESS: 1 Motorola Plaza, Holtsville, NY 11742-1300 USA ISSUED BY: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch LAB ADDRESS: No. 47, 14th Ling, Chia Pau Vil., Lin Kou Dist., New Taipei City, Taiwan ( R.O.C ) TEST LOCATION: No. 19, Hwa Ya 2nd Rd, Wen Hwa Tsuen, Kwei Shan Hsiang, Taoyuan Hsien 333, Taiwan, R.O.C. This test report consists of 5 pages in total. It may be duplicated completely for legal use with the approval of the applicant. It should not be reproduced, except in full, without the written approval of our laboratory. The client should not use it to claim product certification, approval or endorsement by any government agency. The test results in the report only apply to the tested sample. Report No.: SA110922C14 Report Format Version 4.0.0 2 TABLE OF CONTENTS RELEASE CONTROL RECORD ............................................................................................... 3 1. CERTIFICATION ............................................................................................................ 4 2. REDUCED CONDITION FOR SAR ............................................................................... 5 3. MAXIMUM MEASURED POWER OF EUT.................................................................... 5 4. CONCLUSION ............................................................................................................... 5 Report No.: SA110922C14 Report Format Version 4.0.0 3 RELEASE CONTROL RECORD ISSUE NO. REASON FOR CHANGE DATE ISSUED Original release NA Oct. 27, 2011 Report No.: SA110922C14 Report Format Version 4.0.0 4 1. CERTIFICATION PRODUCT:Mobile Payment Module MODEL: MPM-100 BRAND:MOTOROLA APPLICANT:Motorola Solutions, Inc. TEST SAMPLE:ENGINEERING SAMPLE TESTED:Oct. 01 ~ Oct. 24, 2011 STANDARDS: FCC Part 2 (Section 2.1093) FCC OET Bulletin 65, Supplement C (01-01) IEEE C95.1 The above equipment (model: MPM-100) have been tested by Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch, and found compliance with the requirement of the above standards. The test record, data evaluation & Equipment Under Test (EUT) configurations represented herein are true and accurate accounts of the measurements of the sample’s EMC characteristics under the conditions specified in this report. PREPARED BY : , DATE:Oct. 27, 2011 Ivy Lin / Specialist APPROVED BY : , DATE: Oct. 27, 2011 Gary Chang / Technical Manager Report No.: SA110922C14 Report Format Version 4.0.0 5 2. REDUCED CONDITION FOR SAR When output power is ≤ 60/f(GHz) mW, SAR evaluation is not required. 3. MAXIMUM MEASURED POWER OF EUT Mode Conducted power (dBm) Antenna Gain (dBi) EIRP (dBm) Threshold for SAR (dBm) Bluetooth 1.6 1.02 2.62 13.84 4. CONCLUSION No SAR evaluation is required since output power of EUT is less than threshold of SAR.

Report No.: RF110922C14-1 1 Report Format Version 4.0.0 FCC TEST REPORT (Bluetooth) REPORT NO.: RF110922C14-1 MODEL NO.: MPM-100 FCC ID: UZ7MPM100 RECEIVED: Sep. 22, 2011 TESTED: Oct. 01 ~ Oct. 24, 2011 ISSUED: Oct. 27, 2011 APPLICANT: Motorola Solutions, Inc. ADDRESS: 1 Motorola Plaza, Holtsville, NY 11742-1300 USA ISSUED BY: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch LAB ADDRESS: No. 47, 14th Ling, Chia Pau Vil., Lin Kou Dist., New Taipei City, Taiwan ( R.O.C ) TEST LOCATION: No. 19, Hwa Ya 2nd Rd, Wen Hwa Tsuen, Kwei Shan Hsiang, Taoyuan Hsien 333, Taiwan, R.O.C. This test report consists of 75 pages in total. It may be duplicated completely for legal use with the approval of the applicant. It should not be reproduced except in full, without the written approval of our laboratory. The client should not use it to claim product certification, approval, or endorsement by TAF or any government agency. The test results in the report only apply to the tested sample. Report No.: RF110922C14-1 2 Report Format Version 4.0.0 Table of Contents RELEASE CONTROL RECORD ...............................................................................................5 1. CERTIFICATION ............................................................................................................6 2. SUMMARY OF TEST RESULTS ....................................................................................7 2.1 MEASUREMENT UNCERTAINTY .................................................................................7 3. GENERAL INFORMATION.............................................................................................8 3.1 GENERAL DESCRIPTION OF EUT...............................................................................8 3.2 DESCRIPTION OF TEST MODES...............................................................................10 3.2.1 CONFIGURATION OF SYSTEM UNDER TEST .......................................................... 11 3.2.2 TEST MODE APPLICABILITY AND TESTED CHANNEL DETAIL ...............................12 3.3 GENERAL DESCRIPTION OF APPLIED STANDARDS ..............................................14 3.4 DESCRIPTION OF SUPPORT UNITS .........................................................................14 4. TEST TYPES AND RESULTS ......................................................................................15 4.1 RADIATED EMISSION MEASUREMENT ....................................................................15 4.1.1 LIMITS OF RADIATED EMISSION MEASUREMENT..................................................15 4.1.2 TEST INSTRUMENTS .................................................................................................16 4.1.3 TEST PROCEDURES ..................................................................................................18 4.1.4 DEVIATION FROM TEST STANDARD ........................................................................18 4.1.5 TEST SETUP ...............................................................................................................19 4.1.6 EUT OPERATING CONDITIONS .................................................................................19 4.1.7 TEST RESULTS ...........................................................................................................20 4.2 CONDUCTED EMISSION MEASUREMENT ...............................................................33 4.2.1 LIMITS OF CONDUCTED EMISSION MEASUREMENT.............................................33 4.2.2 TEST INSTRUMENTS .................................................................................................33 4.2.3 TEST PROCEDURES ..................................................................................................34 4.2.4 DEVIATION FROM TEST STANDARD ........................................................................34 4.2.5 TEST SETUP ...............................................................................................................35 4.2.6 EUT OPERATING CONDITIONS .................................................................................35 4.2.7 TEST RESULTS ...........................................................................................................36 4.3 NUMBER OF HOPPING FREQUENCY USED ............................................................44 4.3.1 LIMIT OF HOPPING FREQUENCY USED ..................................................................44 4.3.2 TEST INSTRUMENTS .................................................................................................44 4.3.3 TEST PROCEDURES ..................................................................................................44 4.3.4 DEVIATION FROM TEST STANDARD ........................................................................45 4.3.5 TEST SETUP ...............................................................................................................45 4.3.6 TEST RESULTS ...........................................................................................................45 Report No.: RF110922C14-1 3 Report Format Version 4.0.0 4.4 DWELL TIME ON EACH CHANNEL ............................................................................48 4.4.1 LIMIT OF DWELL TIME USED.....................................................................................48 4.4.2 TEST INSTRUMENTS .................................................................................................48 4.4.3 TEST PROCEDURES ..................................................................................................48 4.4.4 DEVIATION FROM TEST STANDARD ........................................................................48 4.4.5 TEST SETUP ...............................................................................................................48 4.4.6 TEST RESULTS ...........................................................................................................49 4.5 CHANNEL BANDW…

Text truncated - open the document above for the full version.

Report No.: RF110922C14 1 Report Format Version 4.0.0 FCC TEST REPORT (RFID) REPORT NO.: RF110922C14 MODEL NO.: MPM-100 FCC ID: UZ7MPM100 RECEIVED: Sep. 22, 2011 TESTED: Oct. 01 ~ Oct. 26, 2011 ISSUED: Oct. 27, 2011 APPLICANT: Motorola Solutions, Inc. ADDRESS: 1 Motorola Plaza, Holtsville, NY 11742-1300 USA ISSUED BY: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch LAB ADDRESS: No. 47, 14th Ling, Chia Pau Vil., Lin Kou Dist., New Taipei City, Taiwan ( R.O.C ) TEST LOCATION: No. 19, Hwa Ya 2nd Rd, Wen Hwa Tsuen, Kwei Shan Hsiang, Taoyuan Hsien 333, Taiwan, R.O.C. This test report consists of 58 pages in total. It may be duplicated completely for legal use with the approval of the applicant. It should not be reproduced except in full, without the written approval of our laboratory. The client should not use it to claim product, certification, approval or endorsement by TAF or any government agency. The test results in the report only apply to the tested sample. The test results in this report are traceable to the national or international standards. Report No.: RF110922C14 2 Report Format Version 4.0.0 Table of Contents RELEASE CONTROL RECORD ...............................................................................................4 1. CERTIFICATION ............................................................................................................5 2. SUMMARY OF TEST RESULTS ....................................................................................6 2.1 MEASUREMENT UNCERTAINTY .................................................................................6 3. GENERAL INFORMATION.............................................................................................7 3.1 GENERAL DESCRIPTION OF EUT...............................................................................7 3.2 DESCRIPTION OF TEST MODES.................................................................................9 3.2.1 CONFIGURATION OF SYSTEM UNDER TEST ............................................................9 3.2.2 TEST MODE APPLICABILITY AND TESTED CHANNEL DETAIL ............................... 11 3.3 GENERAL DESCRIPTION OF APPLIED STANDARDS ..............................................13 3.4 DESCRIPTION OF SUPPORT UNITS .........................................................................13 4. TEST TYPES AND RESULTS ......................................................................................14 4.1 RADIATED EMISSION MEASUREMENT ....................................................................14 4.1.1 LIMITS OF RADIATED EMISSION MEASUREMENT..................................................14 4.1.2 TEST INSTRUMENTS .................................................................................................15 4.1.3 TEST PROCEDURES ..................................................................................................17 4.1.4 DEVIATION FROM TEST STANDARD ........................................................................17 4.1.5 TEST SETUP ...............................................................................................................18 4.1.6 EUT OPERATING CONDITIONS .................................................................................18 4.1.7 TEST RESULTS ...........................................................................................................19 4.2 CONDUCTED EMISSION MEASUREMENT ...............................................................35 4.2.1 LIMITS OF CONDUCTED EMISSION MEASUREMENT.............................................35 4.2.2 TEST INSTRUMENTS .................................................................................................35 4.2.3 TEST PROCEDURES ..................................................................................................36 4.2.4 DEVIATION FROM TEST STANDARD ........................................................................36 4.2.5 TEST SETUP ...............................................................................................................37 4.2.6 EUT OPERATING CONDITIONS .................................................................................37 4.2.7 TEST RESULTS ...........................................................................................................38 4.3 FREQUENCY STABILITY ............................................................................................46 4.3.1 LIMITS OF FREQUENCY STABILITY MEASUREMENT .............................................46 4.3.2 TEST INSTRUMENTS .................................................................................................46 4.3.3 TEST PROCEDURE ....................................................................................................46 4.3.4 DEVIATION FROM TEST STANDARD ........................................................................47 4.3.5 TEST SETUP ...............................................................................................................47 Report No.: RF110922C14 3 Report Format Version 4.0.0 4.3.6 EUT OPERATING CONDITION ...................................................................................47 4.3.7 TEST RESULTS ...........................................................................................................48 4.4 20DB BANDWIDTH ......................................................................................................51 4.4.1 LIMITS OF 20DB BANDWIDTH MEASUREMENT ......................................................51 4.4.2 TEST INSTRUMENTS .................................................................................................51 4.4.3 TEST PROCEDURE ....................................................................................................51 4.4.4 DEVIATION FROM TEST STANDARD ........................................................................51 4.4.5 TEST SETUP ...........................................................…

Text truncated - open the document above for the full version.

1 PHOTOGRAPHS OF THE TEST CONFIGURATION FOR RFID CONDUCTED EMISSION TEST (TEST MODE B) 2 CONDUCTED EMISSION TEST (TEST MODE C) 3 CONDUCTED EMISSION TEST (TEST MODE D) 4 FOR BLUETOOTH CONDUCTED EMISSION TEST (TEST MODE B) 5 CONDUCTED EMISSION TEST (TEST MODE C) 6 CONDUCTED EMISSION TEST (TEST MODE D) 7 CONDUCTED EMISSION TEST (TEST MODE E) 8 FOR RFID RADIATED EMISSION TEST (TEST MODE A) 9 RADIATED EMISSION TEST (TEST MODE B) 10 RADIATED EMISSION TEST (TEST MODE C) 11 RADIATED EMISSION TEST (TEST MODE D) 12 FOR BLUETOOTH RADIATED EMISSION TEST (TEST MODE A) 13 RADIATED EMISSION TEST (TEST MODE B) 14 RADIATED EMISSION TEST (TEST MODE C) 15 RADIATED EMISSION TEST (TEST MODE D) 16 RADIATED EMISSION TEST (TEST MODE E)