UZ7UWT7020Small battery-operated UWB tag transmitting 2.5nsec UWB pulses at 7.55GHz with a magnetic receive interface at 125KHz used for provisioning.

D1685 Rev H 7GHz Tags 7GHz Tags User Manual 2 D10016312 © 2016 ZIH Corp. and/or its affiliates. All rights reserved. Zebra and the stylized Zebra head are trademarks of ZIH Corp., registered in many jurisdictions worldwide. All other trademarks are the property of their respective owners. The copyrights in this document and the software and/or firmware in the products described therein are owned by ZIH Corp. and Zebra’s licensors. Unauthorized reproduction of this manual or the software and/or firmware in the products may result in imprisonment of up to one year and fines of up to $10,000 (17 U.S.C.506). Copyright violators may be subject to civil liability. DartTags, Sapphire, and all product names and/or numbers are trademarks of Zebra. All rights reserved worldwide. All other brand names, product names, or trademarks belong to their respective holders. Proprietary Statement This manual contains proprietary information of Zebra Technologies Corporation and its subsidiaries (“Zebra Technologies”). It is intended solely for the information and use of parties operating and maintaining the equipment described herein. Such proprietary information may not be used, reproduced, or disclosed to any other parties for any other purpose without the express, written permission of Zebra Technologies. Product Improvements Continuous improvement of products is a policy of Zebra Technologies. All specifications and designs are subject to change without notice. Liability Disclaimer Zebra Technologies takes steps to ensure that its published Engineering specifications and manuals are correct; however, errors do occur. Zebra Technologies reserves the right to correct any such errors and disclaims liability resulting therefrom. Limitation of Liability In no event shall Zebra Technologies or anyone else involved in the creation, production, or delivery of the accompanying product (including hardware and software) be liable for any damages whatsoever (including, without limitation, consequential damages including loss of business profits, business interruption, or loss of business information) arising out of the use of, the results of use of, or inability to use such product, even if Zebra Technologies has been advised of the possibility of such damages. Some jurisdictions do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. Caution 3 D10016312 Caution • No modifications to the tag allowed. This includes any type of modification to the case, such as adding metal foils, holes, disassembly, or modifications to the PCB assembly, antenna, battery, or modifications to the product labels, etc. • Prior to installation, carefully inspect the tag, looking for crack, puncture, or any other breach of the plastic case. Damaged tags must not be used. Properly dispose of any damaged tag. • Never dispose of the tag in a fire. • Deactivate the tag when not in use. It is mandatory to deactivate the tag prior to shipment by airplanes. • Follow limitations of use as set forth by any applicable regulatory bodies. • Do not attempt to open the tag and modify the battery due to fire, explosion, and severe burn hazard. Do not recharge, short circuit, crush, dissemble, heat above 100 °C (212 °F), incinerate, or expose contents of the battery to water. • Do not dispose the tag or its lithium batteries in unsorted municipal waste. In most countries, recycling programs are available through non-profit organization, mandated by local government or organized on a voluntary basis. Contact your local government for disposal practices in your area. • When not in use, the tag should be stored in dry and cool conditions at a temperature exceeding 30 °C (86 °F). 4 Contents D10016312 Contents Caution ................................................................................................................ 3 1 Introduction .................................................................................................. 5 2 Installation and Operation .......................................................................... 5 3 7GHz Tags .................................................................................................... 6 3.1 UWT-7020 ................................................................................................................ 6 3.2 UWT-7010 ................................................................................................................ 6 4 Adjustment ................................................................................................... 6 5 Regulatory .................................................................................................... 7 5 Introduction UWT-7020 D10016312 1 Introduction Zebra's Ultra-WideBand (UWB) 7GHz Tags (Models UWT-7020, and UWT-7010) are small battery-operated tags designed for use in sports applications. The UWT-7020 is only used attached to the bladder of a football, and when enabled will track the real time location of that ball on the field. The UWT-7010 is attached to people or assets to track their location in real time. Tags have a unique ID and emit UWB pulses that are received by Zebra's UWB 7GHz Receivers. Receivers report detected tag events to the Zebra Hub running Zebra’s UWB real-time locating system (RTLS) software where tag location information is computed and reported. 2 Installation and Operation 7GHz Tags are shipped with the transmitter off. The tags can be turned on/off using a Zebra configuration tool or a Zebra WherePort. To meet regulatory requirements and increase battery life, Tags are only turned on for specific periods of time, and under specific conditions, for example, the length of an NFL football game. To further their battery life, Tags also slow down their blink rates when idle. 6 Contents D10016312 3 7GHz Tags 3.1 UWT-7020 The UWT-7020 is made only to be installed to the bladder of a football by the football manufacture…

Text truncated - open the document above for the full version.

UWT-7010, UWT-7020 Regulatory Guide ZEBRA and the stylized Zebra head are trademarks of Zebra Technologies Corp., registered in many jurisdictions worldwide. All other trademarks are the property of their respective owners. © 2023 Zebra Technologies Corp. and/or its affiliates. All rights reserved. Zebra Technologies | 3 Overlook Point | Lincolnshire, IL 60069 USA zebra.com MN-004664-01EN Regulatory Information This device is approved under Zebra Technologies Corporation. This guide applies to the following model numbers: •UWT-7010 •UWT-7020 All Zebra devices are designed to be compliant with the rules and regulations in the locations they are sold and will be labeled as required. Local language translation / (BG) Превод на местен език / (CZ) Překlad do místního jazyka / (DE) Übersetzung in die Landessprache / (EL) Μετάφραση τοπικής γλώσσας / (ES) Traducción de idiomas locales / (ET) Kohaliku keele tõlge / (FI) Paikallinen käännös / (FR) Traduction en langue locale / (HR) Prijevod na lokalni jezik / (HU) Helyi nyelvű fordítás / (IT) Traduzione in lingua locale / (JA) 現地語翻訳 / (LT) Vietinės kalbos vertimas / (LV) Tulkojums vietējā valodā / (NL) Vertaling in lokale taal / (PL) Tłumaczenie na język lokalny / (PT) Tradução do idioma local / (RO) Traducere în limba locală / (RU) Перевод на местный язык / (SK) Preklad do miestneho jazyka / (SL) Prevajanje v lokalni jezik / (SR) Превод на локални језик / (SV) Översättning av lokalt språk / (TR) Yerel dil çevirisi / (ZH-CN) 当地语言翻译 / (ZH-TW) 當地語言翻譯 / zebra.com/support Any changes or modifications to Zebra equipment not expressly approved by Zebra could void the user’s authority to operate the equipment. Declared maximum operating temperature: 60°C WARNING: This is a Class A ITE product. Operation in a residential environment could cause radio interference. Regulatory Markings Regulatory markings subject to certification are applied to the device signifying the radio(s) is/are approvedfor use. Refer to the Declaration of Conformity (DoC) for details of other country markings. The DOC is available at: zebra.com/doc . RF Exposure Guidelines Safety Information Reducing RF Exposure – Use Properly Only operate the device in accordance with the instructions supplied. The device complies with internationally recognized standards covering human exposure to electromagnetic fields. For information on international human exposure to electromagnetic fields, refer to the Zebra Declaration of Conformity (DoC) at zebra.com/doc . Use only Zebra tested and approved headset, belt- clips, holsters, and similar accessories to ensure RF exposure compliance. If applicable, follow the instructions for use as detailed in the accessory guide. The use of third-party belt clips, holsters, and similar accessories may not comply with RF exposure compliance requirements and should be avoided. For further information on the safety of RF energy from wireless devices, refer to RF exposure and assessment standards section at zebra.com/ responsibility. Marking and European Economic Area (EEA) Statement of Compliance Zebra hereby declares that this radio equipment is in compliance with Directives 2014/53/EU and 2011/ 65/EU. Any radio operation limitations within EEA countries are identified in Appendix A of EU Declaration of Conformity. The full text of the EU Declaration of Conformity is available at: zebra.com/doc . EU Importer : Zebra Technologies B.V Address: Mercurius 12, 8448 GX Heerenveen, Netherlands Waste Electrical and Electronic Equipment (WEEE) For EU and UK Customers: For products at the end of their life, please refer to recycling/disposal advice at: zebra.com/weee . United States and Canada Regulatory Radio Frequency Interference Notices This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received including interference that may cause undesired operation. NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. RF Exposure Requirements - FCC and ISED The FCC has granted an Equipment Authorization for this device with all reported SAR levels evaluated in compliance with the FCC RF emission guidelines. SAR information on this device is on file with the FCC and can be found under the Display Grant section of fcc.gov/oet/ea/fccid . United Kingdom Statement of Compliance Zebra hereby declares that this radio equipment is in compliance with the Radio Equipment Regulations 2017 and the Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment Regulations 2012. Any radio operation limitations within UK are identified in Appendix A of UK Declaration of Conformity. The full text of the UK Declaration of Conformity is available at: zebra.com/doc . UK Importer: Zebra Technologies Europe Limited Address: Dukes Meadow, Millboard Rd, Bourne End, Buckinghamshire, SL8 5XF Warranty For the complete Zebra hardware product warranty statement, go to: zebra.com\warranty .

Regulatory Engineering Zebra Technologies Corporation 1 Zebra Plaza, | Holtsville, NY 11742 | 1.631.738.2400 phone | 1.631.627.7179 fax | www.zebra.com Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Date: February 17, 2023 Ref: Attestation Statements Part 2.911(d)(5)(i) Filing FCC ID: UZ7UWT7020 Zebra Technologies Corporation (“the applicant”) certifies that the equipment for which authorization is sought is not “covered” equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. Sincerely, Signature : _______________________________ Name and Job Title. : Larry (Qianlin) Zhou / Regulatory Specialist E-mail : [email protected] Tel. : 346-260-3543 Regulatory Engineering Zebra Technologies Corporation 1 Zebra Plaza, | Holtsville, NY 11742 | 1.631.738.2400 phone | 1.631.627.7179 fax | www.zebra.com Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Date: February 17, 2023 Ref: Attestation Statements Part 2.911(d)(5)(ii) Filing FCC ID: UZ7UWT7020 Zebra Technologies Corporation (“the applicant”) certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List as an entity producing “covered” equipment. Sincerely, Signature : _______________________________ Name and Job Title. : Larry (Qianlin) Zhou / Regulatory Specialist E-mail : [email protected] Tel. : 346-260-3543

Federal Communications CommissionDA 21-1294 Before the Federal Communications Commission Washington, D.C. 20554 In the Matter of) ) Zebra Technologies)ET Docket No. 20-17 ) ) Request for Waiver of Sections 15.517(a), ) 15.519(a)(1), or 15.250 of the Commission’s Rules) ) ORDER Adopted: October 19, 2021Released: October 19, 2021 By the Acting Chief, Office of Engineering and Technology: I.INTRODUCTION 1.By this Order, we grant a request by Zebra Technologies (Zebra) for a waiver of our rules governing unlicensed ultra-wideband (UWB) devices to permit the certification and marketing of its positioning system for use in the context of precision tracking in sports venues. We find that this device operating under the specified waiver conditions poses no greater risk of causing harmful interference to communication services than those devices already permitted under the existing rules and that grant of the waiver will serve the public interest. II.BACKGROUND 2.On December 20, 2019, Zebra filed a request for waiver of the Commission’s Part 15 rules to allow Zebra to certify a version of its Dart positioning system for operation in the 7125-8500 MHz range (Zebra subsequently stated that it would operate in the 7125-7900 MHz range). 1 Zebra states that its system, which presently operates as a wideband 2 device in the 5925-7250 MHz band, is used to 1 Zebra Technologies Request for Waiver of the Commission’s Ultra-Wideband Rules to Authorize a Positioning Device in the 7.125-8.500 MHz Band (Request), filed Dec. 20, 2019. See also Letter from Tony S. Lee, Counsel for Zebra Technologies, to Marlene H. Dortch, Secretary, FCC, at 6 (filed Feb. 25, 2021) (Zebra Feb. 25, 2021 ex parte) (narrowing the requested operating range). 2 Although the current iteration of the DartTags is certified as wideband devices under Section 15.250 of our rules, Zebra seeks to certify the new version of its Dart system under the rules provisions for ultra-wideband devices. Unlicensed wideband devices are certified under Section 15.250 while ultra-wideband devices are certified under Section 15.501-15.525. Section 15.250(b) requires that the –10 dB bandwidth of the fundamental emissions shall be at least 50 MHz. Section 15.503(d) defines an ultra-wideband transmitter as an intentional radiator that, at any point Federal Communications CommissionDA 21-1294 2 track small battery-powered tags attached to persons, assets, or safety equipment over a range of 100 meters to an accuracy of less than 30 centimeters. 3 Applications associated with this instant waiver include tracking players in sports venues. NTIA noted as part of coordination that, in the 7125-7900 MHz band segment in the Zebra Technologies waiver request, there are 5,811 frequency assignments in the Government Master File. Approximately 90 percent of those assignments are for fixed systems used to support the missions of the federal agencies. 3.The Dart UWB Real Time Location System (RTLS) consists of a hub, connected by cable to multiple (four or more) receive-only devices that receive short UWB packet bursts transmitted from the associated Radio Frequency Identification (RFID) tags (DartTags). This set-up enables Zebra to obtain differential time of arrival calculations that provide accurate two-dimensional localization of individual assets or personnel. The current DartTags operating in the 5925-7250 MHz band on a nominal center frequency of 6550 MHz comply with the Part 15.250 rules and do not require a waiver. 4 Each tag generally transmits 2.5 nanosecond pulses between 1-50 times per second. For purposes of their deployment in National Football League (NFL) applications, the DartTags transmit at different rates which range between 1 to 25 Hz. The tag transmit rate for each device is controlled by an embedded accelerometer and depends upon the specific use case associated with each tag. 5 Zebra states that the DartTags can run for about a year on a small non-rechargeable coin-cell with a usable operating range of up to six hundred feet, depending on the accuracy requirement. Because the current tags operate under Section 15.250 of our rules, the maximum allowable average EIRP level is -41.3 dBm/MHz, which results in a signal level that is just above the thermal noise floor at a short distance. Zebra further states that the Dart system must be installed by competent professionals that are trained to ensure that it functions correctly when moved to different venues. It says that it is necessary to use professionally trained installers who are familiar with these systems due to the cost and complexity of the DartTags and associated passive receivers. Dart system operators also ensure that each DartTag is activated and deactivated via a magnetic wand before and after each game. 4.A version of the Dart system that Zebra currently uses operates across 500 MHz in the 63006800 MHz band and is compliant with the stringent Section 15.250 power limits. 6 Zebra desires to manufacture a Dart system that would operate in the 7125-7900 MHz band, which it has identified as being well-suited for precision tracking in sports venues. It seeks a waiver because outdoor operations of the Dart system are not permitted in this higher frequency band under the Part 15 unlicensed technical rules. 5.Zebra identifies three potential rule sections for operation under a waiver to allow it to use its Dart system above 7125 MHz: Sections 15.517(a), 15.519(a)(1), or 15.250(a) and (d)(1). 7 Section 15.517 governs the technical requirements for indoor UWB systems and Section 15.517(a) limits operation under the rule to UWB transmitters employed solely for indoor operation. Zebra states that it would require a waiver of this requirement because the Dart system has some outdoor applications. Section 15.519 specifies the technical requirements for hand held UWB systems. Under Section 15.519(a)(1), a UWB device may transmit only when it is sending information to an associated receiver and must cease…

Text truncated - open the document above for the full version.

Regulatory Engineering Zebra Technologies Corporation 1 Zebra Plaza, | Holtsville, NY 11742 | 1.631.738.2400 phone | 1.631.627.7179 fax | www.zebra.com Date: March 27, 2023 Federal Communications Commission Office of Engineering and Technology Equipment Authorization Division 7435 Oakland Mills Road Columbia, MD 21046 Ref: FCC ID: UZ7UWT7020 Waiver DA 21-1294 specifies the rules under which Zebra can deploy its Dart positioning system in the 7125-7900MHz frequency range. The UWB tag (FCC ID: UZ7UWT7020) is a small battery-operated UWB transmitter that is part of that system. Zebra certifies that the UWB tag (FCC ID: UZ7UWT7020) meets all the requirements of waiver DA 21- 1294. If you have any questions regarding this authorization, please contact me directly. Signature : _______________________________ Name and Job Title. : Larry (Qianlin) Zhou / Regulatory Specialist E-mail : [email protected] Tel. : 346-260-3543

Regulatory Engineering Zebra Technologies Corporation 1 Zebra Plaza, | Holtsville, NY 11742 | 1.631.738.2400 phone | 1.631.627.7179 fax | www.zebra.com Date: March 14, 2023 Federal Communications Commission Office of Engineering and Technology Equipment Authorization Division 7435 Oakland Mills Road Columbia, MD 21046 Ref: FCC ID: UZ7UWT7020 Confidentiality Request Pursuant to the provisions of Sections 0.457 and 0.459 of Commission’s rules (47CFR§§0.457, 0.459), we are requesting the Commission to withhold the following attachment(s) as confidential document from public disclosure indefinitely.  Schematic Diagram  Block Diagram  Part List  Operational Description Above mentioned document contains detailed system and equipment description are considered as proprietary information in operation of the equipment. The public disclosure of above documents might be harmful to our company and would give competitor an unfair advantage in the market. In additional to above mentioned documents, pursuant to Public Notice DA 04-1705 of the Commission’ s policy, in order to comply with the marketing regulations in 47 CFT §2.803 and the importation rules in 47 CFR §2.1204, while ensuring that business sensitive information remains confidential until the actual marketing of newly authorized devices. We are requesting the commission to grant shot-term confidentiality request on the following attachment(s) for 180 days after the grant as outlined in Public Notice DA 04-1705.  Internal Photos  External Photos  Test Setup Photos  User Manual It is our understanding that all measurement test reports, FCC ID label format and correspondent during certification review process cannot be granted as confidential documents and those information will be available for public review once the grant of equipment authorization is issued. Regulatory Engineering Zebra Technologies Corporation 1 Zebra Plaza, | Holtsville, NY 11742 | 1.631.738.2400 phone | 1.631.627.7179 fax | www.zebra.com If you have any questions regarding this authorization, please contact me directly. Signature : _______________________________ Name and Job Title. : Larry (Qianlin) Zhou / Regulatory Specialist E-mail : [email protected] Tel. : 346-260-3543

HEADQUARTERS: 914 WEST PATAPSCO AVENUE • BALTIMORE, MARYLAND 21230 • PHONE (410) 354-3300 • FAX (410) 354-3313 Report: WIR124171-FCC-RF Exposure Rev. 1 © 2023, Eurofins Electrical and Electronic Testing NA, Inc. Page 1 of 4 Maryland | California | Texas www.metlabs.com DOC-WIR TEMP-FCC22-24-27-90-7-12-2021 – Rev 1 - Approved by DOC Manager RF Exposure Report (FCC) Report No.: WIR124171-FCC-RF Exposure Rev. 1 Test Model: UWT-7020 Received Date: October 14, 2022 Test Date: February 24, 2023 Issued Date: March 23, 2023 Applicant: Zebra Technologies Corporation Address: 1 Zebra Plaza, Holtsville, NY 11742 Issued By: Eurofins Electrical and Electronic Testing NA, Inc. Lab Address: 914 W. Patapsco Avenue, Baltimore, MD 21230 Certificates and reports shall not be reproduced except in full, without the written permission of Eurofins Electrical and Electronic Testing NA, Inc. While use of the A2LA logo in this report reflects Eurofins Electrical and Electronic Testing NA, Inc. accreditation under these programs, the report must not be used by the client to claim product certification, approval, or endorsement by A2LA, or any agency of the Federal Government. This letter of transmittal is not a part of the attached report. Eurofins Electrical and Electronic Testing NA, Inc. is part of the Eurofins Electrical & Electronics (E&E) global compliance network. HEADQUARTERS: 914 WEST PATAPSCO AVENUE • BALTIMORE, MARYLAND 21230 • PHONE (410) 354-3300 • FAX (410) 354-3313 Report: WIR124171-FCC-RF Exposure Rev. 1 © 2023, Eurofins Electrical and Electronic Testing NA, Inc. Page 2 of 4 Maryland | California | Texas www.metlabs.com DOC-EMC TEMP-1 (REG) 11-05-2021– Rev. 1 - Approved by DOC Manager 1. Certificate of Conformity Product: UWT-7020 Brand: Zebra Technologies Corporation Test Model: UWT-7020 FCC ID: UZ7UWT7020 Sample Status: EMC Applicant: Zebra Technologies Corporation Test Date: February 24, 2023 Standard: 47 CFR FCC Part 2.1093 Donald Salguero Wireless Laboratory Engineer Engineering Statement: The measurements shown in this report were made in accordance with the procedures indicated. I assume full responsibility for the accuracy and completeness of these measurements, and for the qualifications of all persons taking them. It is further stated that upon the basis of the measurements made, the equipment tested is capable of operation in accordance with the requirements. Michael Griffiths Manager, Wireless Laboratory HEADQUARTERS: 914 WEST PATAPSCO AVENUE • BALTIMORE, MARYLAND 21230 • PHONE (410) 354-3300 • FAX (410) 354-3313 Report: WIR124171-FCC-RF Exposure Rev. 1 © 2023, Eurofins Electrical and Electronic Testing NA, Inc. Page 3 of 4 Maryland | California | Texas www.metlabs.com DOC-EMC TEMP-1 (REG) 11-05-2021– Rev. 1 - Approved by DOC Manager Report Status Sheet Revision Report Date Reason for Revision Ø March 1, 2023 Initial Issue. 1 March 23, 2023 Updated customer address; Added FCC ID. HEADQUARTERS: 914 WEST PATAPSCO AVENUE • BALTIMORE, MARYLAND 21230 • PHONE (410) 354-3300 • FAX (410) 354-3313 Report: WIR124171-FCC-RF Exposure Rev. 1 © 2023, Eurofins Electrical and Electronic Testing NA, Inc. Page 4 of 4 Maryland | California | Texas www.metlabs.com DOC-EMC TEMP-1 (REG) 11-05-2021– Rev. 1 - Approved by DOC Manager 2. RF Exposure Requirement: 47 CFR 2.1093(d)(1) Applications for equipment authorization of portable RF sources subject to routine environmental evaluation must contain a statement confirming compliance with the limits specified in § 1.1310 of this chapter as part of their application. Technical information showing the basis for this statement must be submitted to the Commission upon request. The SAR limits specified in § 1.1310(a) through (c) of this chapter shall be used for evaluation of portable devices transmitting in the frequency range from 100 kHz to 6 GHz. Portable devices that transmit at frequencies above 6 GHz shall be evaluated in terms of the MPE limits specified in Table 1 to § 1.1310(e)(1) of this chapter. A minimum separation distance applicable to the operating configurations and exposure conditions of the device shall be used for the evaluation. In general, maximum time-averaged power levels must be used for evaluation. All unlicensed personal communications service (PCS) devices and unlicensed NII devices shall be subject to the limits for general population/uncontrolled exposure. EUT Frequency of operation: 643.3MHz OBW centered at 7.5GHz SAR – Per § 2.1093 (d)(1), equipment with a transmit frequency above 6GHz shall be evaluated in terms of MPE S limit = 1 mW/cm 2 Where S = power density in mW/cm2 P = output power to antenna in mW G = gain of antenna in linear scale Pi = 3.1416 R = distance between observation point and center of the radiator in cm Measured average EIRP = -44.99dBm/MHz = 0.000032 mW = P*G Minimum Separation distance = 0.5cm S = 0.000032 / (4*3.1416*(0.5)^2) = 0.000010 mW/cm 2 S limit > S EUT complies to RF exposure at 5mm

HEADQUARTERS: 914 WEST PATAPSCO AVENUE • BALTIMORE, MARYLAND 21230 • PHONE (410) 354-3300 • FAX (410) 354-3313 Report: WIR124171A-FCC519 Rev. 3 © 2023, Eurofins Electrical and Electronic Testing NA, Inc. Page 1 of 35 Maryland | California | Texas www.metlabs.com DOC-EMC TEMP-1 (REG) 09-10-2022 - Rev. 0 - Approved by DOC Manager March 23, 2023 Zebra Technologies Corporation Thomas Warner 1 Zebra Plaza, Holtsville NY 11742 Dear Thomas Warner, Enclosed is the EMC Wireless test report for compliance testing of the Zebra Technologies Corporation, UWT-7020 as tested to the requirements of Title 47 of the CFR, Ch. 1 (10-1-06 ed.), Part 15, Subpart F for Intentional Radiators. Thank you for using the services of Eurofins Electrical and Electronic Testing NA, Inc. If you have any questions regarding these results or if Eurofins Electrical and Electronic Testing NA, Inc. can be of further service to you, please feel free to contact me. Sincerely yours, Eurofins Electrical and Electronic Testing NA, Inc. Michelle Tawmging Documentation Department Reference: (\Zebra Technologies Corporation\WIR124171A-FCC519 Rev. 3) Certificates and reports shall not be reproduced except in full, without the written permission of Eurofins Electrical and Electronic Testing NA, Inc. HEADQUARTERS: 914 WEST PATAPSCO AVENUE • BALTIMORE, MARYLAND 21230 • PHONE (410) 354-3300 • FAX (410) 354-3313 Report: WIR124171A-FCC519 Rev. 3 © 2023, Eurofins Electrical and Electronic Testing NA, Inc. Page 2 of 35 Maryland | California | Texas www.metlabs.com DOC-EMC TEMP-1 (REG) 09-10-2022 - Rev. 0 - Approved by DOC Manager Electromagnetic Compatibility Criteria Test Report for the Zebra Technologies Corporation UWT-7020 Tested under the FCC Certification Rules contained in Title 47 of the CFR, Part 15.519 Subpart F for Intentional Radiators Report: WIR124171A-FCC519 Rev. 3 March 23, 2023 Prepared For: Zebra Technologies Corporation 1 Zebra Plaza, Holtsville NY 11742 Prepared By: Eurofins Electrical and Electronic Testing NA, Inc. 914 W. Patapsco Ave. Baltimore, MD 21230 HEADQUARTERS: 914 WEST PATAPSCO AVENUE • BALTIMORE, MARYLAND 21230 • PHONE (410) 354-3300 • FAX (410) 354-3313 Report: WIR124171A-FCC519 Rev. 3 © 2023, Eurofins Electrical and Electronic Testing NA, Inc. Page 3 of 35 Maryland | California | Texas www.metlabs.com DOC-EMC TEMP-1 (REG) 09-10-2022 - Rev. 0 - Approved by DOC Manager Electromagnetic Compatibility Criteria Test Report for the Zebra Technologies Corporation UWT-7020 Tested under the FCC Certification Rules contained in Title 47 of the CFR, Part 15.519 Subpart F for Intentional Radiators Donald Salguero WIR Laboratory Engineer Engineering Statement: The measure…

Text truncated - open the document above for the full version.