UZZSFQ11Sound Kick 2

Sound Kick 2 SFQ-11 User Manual 2 Safety Information IMPORTANT SAFETY INSTRUCTIONS 1. Read these instructions. 2. Keep these Instructions. 3. Heed all Warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with dry cloth. 7. Do not block any ventilation openings. Install in accordance with the manufacturer's instructions. 8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 9. Do not defeat the safety purpose of the polarized or grounding - type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. 10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. 11. Only use attachments/accessories specified by the manufacturer. 12. Use only with the cart, stand, tripod, bracket or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over. PORTABLE CART WARNING (Symbol provided by RETAC) 13. Unplug this apparatus during lightning storms or when unused for long periods of time. 14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. 15. Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as vase,shall not be placed on the apparatus. 16. The mains plug is used as disconnect device and it shall remain readily operable during intended use. In order to disconnect the mains plug from the mains completely, the mains plug should be disconnected from the mains socket outlet completely. 17. The batteries (battery pack & batteries installed) shall not be exposed to excessive heat such as sunshine, fire or the like. 3 18. Do not place any naked flame sources, such as lighted candles, on the apparatus. 19. The battery used in this product must be properly recycled or disposed of. Please contact your local recycling center for proper battery handling and disposal instructions. FCC Information: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Canada IC statements This device complies with Industry Canada’s licence-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause interference; and (2) This device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. CAN ICES-3 (B)/NMB-3 (B) Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:  Reorient or relocate the receiving antenna.  Increase the separation between the equipment and receiver.  Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.  Consult the dealer or an experienced radio TV technician for help. Warnings: The device meets the exemption from the routine evaluation limits in section 2.5 of RSS 102 and users can obtain Canadian information on RF exposure and compliance from the Canadian Representative Burnport Holdings Ltd. 72MT Belcher Pls, East, Calgary, Alberta, T2Z 2G1, CANADA. Tel: 403-257-4961 FCC&IC Radiation Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment and meets the exemption from the routine evaluation limits in section 2.5 of RSS 102. For compatibility between the system and another device with Bluetooth technology, consult the device's documentation and dealer. In some countries, there may be restrictions on using Bluetooth devices. Check with your local authorities. is a registered trademark of Bluetooth SIG, Inc Please read rating label at the bottom of system for power input and other safety information. 4 CAUTION - Proper Installation  Install the system in a place which is level, dry and neither too hot nor too cold. The appropriate temperature is between 5 o C and 35 o C.  Install the system in a location with ade…

Text truncated - open the document above for the full version.

Size: 156mm x 100mm 15 cm (5- 15 / 16 ") 15 cm (5- 15 / 16 ") 15 cm (5- 15 / 16 ") QDID: XXXXXXX Informations FCC (Commission fédérale des communications U.S.) : Cet appareil est conforme à l’article 15 du règlement de la FCC. Son utilisation est soumise aux deux conditions suivantes : (1) cet appareil ne doit pas provoquer d’interférences préjudiciables, et (2) il doit accepter toute interférence reçue, y compris celles risquant d’engendrer un fonctionnement indésirable. Déclarations d’Industrie Canada Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. Cet équipement est conforme à l'exposition aux rayonnements IC limites établies pour un environnement non contrôlé. Cet équipement doit être installé et utilisé avec un minimum de 20 cm de distance entre le radiateur et votre corps. Remarque : ce matériel a été testé et trouvé conforme aux limites de l'article 15 de la règlementation FCC pour les appareils numériques de classe B. Ces limites sont conçues pour fournir une protection raisonnable contre les interférences nuisibles dans une installation résidentielle. Ce matériel génère, utilise et peut émettre des fréquences radio et, s'il n'est pas installé et utilisé conformément aux instructions, peut causer des interférences nuisibles aux communications radio. Toutefois, il n'existe aucune garantie que des interférences ne se produiront pas dans une installation particulière. Si ce matériel cause des interférences nuisibles à la réception radio ou télévision, ce qui peut être déterminé en éteignant l'appareil, l'utilisateur est encouragé à essayer de corriger l'interférence par une ou plusieurs des mesures suivantes : • Réorienter ou déplacer l'antenne de réception. • Augmenter la distance entre l'appareil et le récepteur. • Brancher l'appareil à une prise de courant sur un circuit diérent de celui auquel le récepteur est branché. • Consulter le revendeur ou un technicien radio/ télévision expérimenté. Avertissements : L'appareil répond à l'exemption de l'évaluation de routine des limites de la section 2.5 de la norme CNR-102 et les utilisateurs peuvent obtenir des informations canadiennes sur l'exposition aux radiofréquences et la conformité auprès du représentant canadien Burnport Holdings Ltd 72MT Belcher, East, Calgary, Alberta, T2Z 2G1, CANADA. Téléphone : 403-257-4961 ATTENTION - Installation correcte • Installez le système sur une surface horizontale, dans un endroit sec et ni trop chaud ni trop froid. La température d'utilisation se situe entre 5°C et 35°C. • Installez le système dans un lieu bien aéré pour éviter qu'il ne surchaue. • Laissez une distance susante entre le système et le téléviseur. • Éloignez le système du téléviseur an d'éviter les interférences avec ce dernier. ATTENTION - Ventilation correcte Pour prévenir tout risque de choc électrique, d'incendie, ou tout autre dommage, placez l'appareil comme suit : Face avant : pas d'obstructions et un espace libre. Côtés / dessus / arrière : aucun obstacle dans les zones indiquées ci-dessous. Dessous : posez l'appareil sur une surface horizontale. Maintenez une circulation d'air susante pour la ventilation en plaçant l'appareil sur un support de 10 cm (3-15/16") de haut ou plus. Consignes de sécurité AVERTISSEMENTS : POUR RÉDUIRE LE RISQUE D'INCENDIE OU D'ÉLECTROCUTION, NE PAS EXPOSER CET APPAREIL À LA PLUIE OU À L'HUMIDITÉ. N'ENLEVEZ PAS LE COUVERCLE et N'OUVREZ PAS LE BOÎTIER. Des tensions élevées dangereuses sont présentes à l'intérieur. Non réparable par l'utilisateur. Toutes les réparations doivent être eectuées par un personnel qualié. IMPORTANTES INSTRUCTIONS DE SÉCURITÉ 1. Lisez attentivement ces instructions. 2. Conservez ces instructions. 3. Respectez tous les avertissements. 4. Suivez toutes les instructions. 5. N'utilisez pas cet appareil près de l'eau. 6. Nettoyez-le avec un linge sec uniquement. 7. Ne bloquez pas les fentes d'aération. Installez l'appareil conformément aux instructions du fabricant. 8. N'installez pas l'appareil près de sources de chaleur telles que radiateurs, registres de chaleur, poêles ou autres appareils (y compris les amplicateurs) produisant de la chaleur. 9. Ne détruisez pas la fonction de sécurité de la prise polarisée ou avec mise à la terre. Une prise polarisée comporte deux broches, l'une étant plus large que l'autre. Une prise avec mise à la terre comporte trois broches, la troisième étant la broche de terre. La broche plus large, ou la broche de terre, sont là pour votre sécurité. Si la prise fournie ne correspond pas à vos prises secteur, demandez à un électricien de la remplacer. 10. Protégez le cordon d'alimentation pour qu'il ne soit pas écrasé ou pincé, particulièrement au niveau de la prise de courant et au point où il sort de l'appareil. 11 Utilisez uniquement les accessoires spéciés par le fabricant. Version Canada Le symbole de l'éclair dans un triangle est destiné à mettre en garde l'utilisateur contre la présence de tensions dangereuses à l'intérieur du boîtier du produit, d'une puissance susante pour constituer un risque de choc électrique. Le symbole du point d'exclamation dans un triangle est destiné à avertir l'utilisateur de la présence d'importantes instructions d'utilisation et d'entretien dans la documentation jointe à l'appareil. 12. Utilisez uniquement avec le chariot, le pied, le trépied, le support ou la table spéciés par le fabricant ou vendus avec l'appareil. Quand vous utilisez un chariot, soyez prudent lorsque vous déplacez l'ensemble chariot / appareil pour éviter les blessures en cas de renversement. NE PAS OUVRIR - RISQUE D'ÉLECTROCUTION ATTENTION Vue de face :Vue de côté : AVERTISSEMENT RELATIF AU CHARIOT DE …

Text truncated - open the document above for the full version.

13. Unplug this apparatus during lightning storms or when unused for long periods of time. 14. Refer all servicing to qualied service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. 15. Apparatus shall not be exposed to dripping or splashing and no objects lled with liquids, shall not be placed on the apparatus. 16. The mains plug is used as disconnect device and it shall remain readily operable during intended use. In order to disconnect the mains plug from the mains completely, the mains plug should be disconnected from the mains socket outlet completely. 17. The batteries (battery pack & batteries installed) shall not be exposed to excessive heat such as sunshine, re or the like. 18. Do not place any naked ame sources, such as lighted candles, on the apparatus. 19. The battery used in this product must be properly recycled or disposed of. Please contact your local recycling center for proper battery handling and disposal instructions. For compatibility between the unit and another device with Bluetooth technology, consult the device's documentation and dealer. In some countries, there may be restrictions on using Bluetooth devices. Check with your local authorities. is a registered trademark of Bluetooth SIG, Inc WARNING! Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type. WARNING! Changes or modications to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Please read rating label at the bottom of system for power input and other safety information. FCC Information: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Warnings: The device meets the exemption from the routine evaluation limits in section 2.5 of RSS 102 and users can obtain Canadian information on RF exposure and compliance from the Canadian Representative Burnport Holdings Ltd. 72MT Belcher Pls, East, Calgary, Alberta, T2Z 2G1, CANADA. Tel: 403-257-4961 S afety Information WARNINGS: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. DO NOT REMOVE COVER or OPEN THE CABINET. Dangerous high voltages are present inside the enclosure. No user serviceable parts inside. Leave all servicing to qualied service personnel. PORTABLE CART WARNING (Symbol provided by RETAC) Canada IC statments This device complies with Industry Canada’s licence-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause interference; and (2) This device must accept any interference, including interference that may cause undesired operation of the device. This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determ ined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the following measures:  Reorient or relocate the receiving antenna.  Increase the separation between the equipment and receiver.  Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.  Consult the dealer or an experienced radio TV technician for help. By disposing of this product correctly, you will help to conserve natural resources and will help prevent potential negative eects on the environment and human health that could otherwise be caused by inappropriate waste handling of this product. For more information about collection point and recycling of this product, please contact your local municipal oce, your household waste disposal service or the shop where you purchased the product. Front View:Side View: Information for Users on Disposal of Old Equipment [European Union] This symbol indicates that the electrical and electronic equipment should not be disposed as general household waste at its end-of-life. Instead, the product should be handed over to the applicable collection point for the recycling in accordance with your national legislation. Attention: This symbol is only valid in the European Union. IMPORTANT SAFETY INSTRUCTIONS 1. Read these instructions. 2. Keep these Instructions. 3. Heed all Warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with dry cloth. 7. Do not block any ventilation openings. Install in accordance with the manufacturer's instructions. 8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including ampliers) that produce heat. 9. Do not defeat the safety purpose of the polarized or grounding - type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided f…

Text truncated - open the document above for the full version.

Beautiful Enterprise Co., Ltd. 27 th Floor, Beautiful Group Tower, Tel: 852-23270195 77 Connaught Road Central, Hong Kong Fax: 852-23523380 Declaration of Authorization We Name: Beautiful Enterprise Co., Ltd. Address: 27th Floor, Beautiful Group Tower, 77 Connaught Road Central City: Hong Kong Country: China Declare that: Name Representative of agent: Ms. Cathy Wang Agent Company name: BTL Inc. Address: No.3 Jinshagang 1st Road, Shixia, Dalang Town City: Dong Guan Country: China is authorized to apply for Certification and signing related documents of the following product(s), including 731 form(s): Product description: Sound Kick 2 Type designation: SFQ-11 Trademark: on our behalf. Date: 2015-01-29 City: Hong Kong Name: John Liao Function: Product Approbation Manager Signature:. Notes: (1): Required for FCC application (2): For FCC it must be the Grantee Code “owner” or the authorized agent.

Beautiful Enterprise Co., Ltd. 27 th Floor, Beautiful Group Tower, Tel: 852-23270195 77 Connaught Road Central, Hong Kong Fax: 852-23523380 Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 Gentlemen: This letter is to comply with Sections 0.457 and 0.459 pertaining to confidential material. Beautiful Enterprise Co., Ltd. would like the following documents regarding this submission for FCC ID: UZZSFQ11 to be kept confidential. 1. Schematic 2. Block diagram 3. Circuit description The above material contains trade secrets or technical data, which would customarily be guarded from competitors. We do not want these documents to be accessible to the general public. Sincerely, Name: John Liao Title: Product Approbation Manager Jan 26, 2015

Project No.: 1501C124 Page 2 of 22 Project No.: 1501C124 Page 3 of 22 Project No.: 1501C124 Page 4 of 22 Project No.: 1501C124 Page 5 of 22 Project No.: 1501C124 Page 6 of 22

Project No.: 1501C124 Page 7 of 22 Project No.: 1501C124 Page 8 of 22 Project No.: 1501C124 Page 9 of 22 Project No.: 1501C124 Page 10 of 22 Project No.: 1501C124 Page 11 of 22 Project No.: 1501C124 Page 12 of 22 Project No.: 1501C124 Page 13 of 22 Project No.: 1501C124 Page 14 of 22 Project No.: 1501C124 Page 15 of 22 Project No.: 1501C124 Page 16 of 22 Project No.: 1501C124 Page 17 of 22 Project No.: 1501C124 Page 18 of 22 Project No.: 1501C124 Page 19 of 22 Project No.: 1501C124 Page 20 of 22 Project No.: 1501C124 Page 21 of 22 Project No.: 1501C124 Page 22 of 22

FCC RF EXPOSURE REPORT FCC ID: UZZSFQ11 Project No. : 1501C124 Equipment : Sound Kick 2 Model : SFQ-11 Applicant : Beautiful Enterprise Co., Ltd. Address : 27th Floor, Beautiful Group Tower, 77 Connaught Road Central, Hong Kong According: : FCC Guidelines for Human Exposure IEEE C95.1 BTL INC. No.3, Jinshagang 1st Road, Shixia, Dalang Town, Dongguan, China. TEL: +86-769-8318-3000 FAX: +86-769-8319-6000 MPE CALCULATION METHOD: Calculation Method of RF Safety Distance: where: S = power density P = power input to the antenna G = power gain of the antenna in the direction of interest relative to an isotropic radiator R = distance to the center of radiation of the antenna Table for Filed Antenna Ant. Brand Model Name Antenna Type Connector Gain(dBi) 1 N/A N/A Printed N/A -1.72 TEST RESULTS EUT： Sound Kick 2 Model Name : SFQ-11 Temperature： 25 °C Relative Humidity: 55 % Test Voltage : DC 3.7V Test Mode ： TX Mode _1Mbps /CH00, CH39, CH78 Antenna Gain (dBi) Antenna Gain (numeric) Peak Output Power (dBm) Peak Output Power (mW) Power Density (S) (mW/cm 2 ) Limit of Power Density (S) (mW/cm 2 ) Te s t Result -1.72 0.6730 4.17 2.6122 0.000349911 Complies -1.72 0.6730 4.40 2.7542 0.000368941 Complies -1.72 0.6730 4.67 2.9309 0.000392601 Complies EUT： Sound Kick 2 Model Name : SFQ-11 Temperature： 25 °C Relative Humidity: 55 % Test Voltage : DC 3.7V Test Mode ： TX Mode _3Mbps /CH00, CH39, CH78 Antenna Gain (dBi) Antenna Gain (numeric) Peak Output Power (dBm) Peak Output Power (mW) Power Density (S) (mW/cm 2 ) Limit of Power Density (S) (mW/cm 2 ) Te s t Result -1.72 0.6730 4.10 2.5704 0.000344311 Complies -1.72 0.6730 4.14 2.5942 0.000347501 Complies -1.72 0.6730 4.58 2.8708 0.000384551 Complies Note: the calculated distance is 20 cm.

Report No.: BTL-FICP-1-1501C124 Page 1 of 11 5 FCC&IC Radio Test Report FCC ID: UZZSFQ11 IC: 7633A-SFQ11 This report concerns (check one): Original Grant Class II Change Project No. : 1501C124 Equipment : Sound Kick 2 Model Name : SFQ-11 Applicant : Beautiful Enterprise Co., Ltd. Address : 27th Floor, Beautiful Group Tower, 77 Connaught Road Central, Hong Kong Date of Receipt : Jan. 19, 2015 Date of Test : Jan. 19, 2015 ~ Jan. 27, 2015 Issued Date : Jan. 28, 2015 Tested by : BTL Inc. Testing Engineer : (David Mao) Technical Manager : (Leo Hung) Authorized Signatory : (Steven Lu) BTL INC. No.3, Jinshagang 1st Road, Shixia, Dalang Town, Dongguan, Guangdong, China. TEL: +86-769-8318-3000 FAX: +86-769-8319-6000 Report No.: BTL-FICP-1-1501C124 Page 2 of 115 Declaration BTL represents to the client that testing is done in accordance with standard procedures as applicable and that test instruments used has been calibrated with the standards traceable to National Measurement Laboratory (NML) of CHINA, or National Institute of Standards and Technology (NIST) of U.S.A. BTL's reports apply only to the specific samples tested under conditions. It is manufacture’s responsibility to ensure that additional production units of this model are manufactured with the identical electrical and mechanical components. BTL shall have no liability for any declarations, inferences or generalizations drawn by the client or others from BTL issued reports. BTL’s reports must not be used by the client to claim product endorsement by the authorities or any agency of the Government. This report is the confidential property of the client. As a mutual protection to the clients, the public and BTL-self, extracts from the test report shall not be reproduced except in full with BTL’s authorized written approval. BTL’s laboratory quality assurance procedures are in compliance with the ISO Guide 17025 requirements, and accredited by the conformity assessment authorities listed in this test report. Limitation For the use of the authority's logo is limited unless the Test Standard(s)/Scope(s)/Item(s) mentioned in this test report is (are) included in the conformity assessment authorities acceptance respective. Report No.: BTL-FICP-1-1501C124 Page 3 of 115 Table of Contents Page 1 . CERTIFICATION 7 2 . SUMMARY OF TEST RESULTS 8 2.1 TEST FACILITY 9 2.2 MEASUREMENT UNCERTAINTY 9 3 . GENERAL INFORMATION 10 3.1 GENERAL DESCRIPTION OF EUT 10 3.2 DESCRIPTION OF TEST MODES 12 3.3 TABLE OF PARAMETERS OF TEXT SOFTWARE SETTING 12 3.4 BLOCK DIAGRAM SHOWING THE CONFIGURATION OF SYSTEM TESTED 13 3.5 DESCRIPTION OF SUPPORT UNITS 13 4 . EMC EMISSION TEST 14 4.1 CONDUCTED EMISSION MEASUREMENT 14 4.1.1 POWER LINE CONDUCTED EMISSION LIMITS 14 4.1.2 TEST PROCEDURE 14 4.1.3 DEVIATION FROM TEST STANDARD 14 4.1.4 TEST SETUP 15 4.1.5 EUT OPERATING CONDITIONS 15 4.1.6 EUT TEST CONDITIONS 15 4.1.7 TEST RESULTS 15 4.2 RADIATED EMISSION MEASUREMENT 16 4.2.1 RADIATED EMISSION LIMITS 16 4.2.2 TEST PROCEDURE 17 4.2.3 DEVIATION FROM TEST STANDARD 17 4.2.4 TEST SETUP 18 4.2.5 EUT OPERATING CONDITIONS 19 4.2.6 EUT TEST CONDITIONS 19 4.2.7 TEST RESULTS (9KHZ TO 30MHZ) 19 4.2.8 TEST RESULTS (BETWEEN 30MHZ TO 1000 MHZ) 20 4.2.9 TEST RESULTS (ABOVE 1000 MHZ) 20 5 . NUMBER OF HOPPING CHANNEL 21 5.1 APPLIED PROCEDURES 21 5.1.1 TEST PROCEDURE 21 5.1.2 DEVIATION FROM STANDARD 21 5.1.3 TEST SETUP 21 5.1.4 EUT OPERATION CONDITIONS 21 5.1.5 EUT TEST CONDITIONS 21 5.1.6 TEST RESULTS 21 Report No.: BTL-FICP-1-1501C124 Page 4 of 115 Table of Contents Page 6 . AVERAGE TIME OF OCCUPANCY 22 6.1 APPLIED PROCEDURES / LIMIT 22 6.1.1 TEST PROCEDURE 22 6.1.2 DEVIATION FROM STANDARD 22 6.1.3 TEST SETUP 22 6.1.4 EUT OPERATION CONDITIONS 23 6.1.5 EUT TEST CONDITIONS 23 6.1.6 TEST RESULTS 23 7 . HOPPING CHANNEL SEPARATION MEASUREMENT 24 7.1 APPLIED PROCEDURES / LIMIT 24 7.1.1 TEST PROCEDURE 24 7.1.2 DEVIATION FROM STANDARD 24 7.1.3 TEST SETUP 24 7.1.4 EUT TEST CONDITIONS 24 7.1.5 TEST RESULTS 24 8 . BANDWIDTH TEST 25 8.1 APPLIED PROCEDURES 25 8.1.1 TEST PROCEDURE 25 8.1.2 DEVIATION FROM STANDARD 25 8.1.3 TEST SETUP 25 8.1.4 EUT OPERATION CONDITIONS 25 8.1.5 EUT TEST CONDITIONS 25 8.1.6 TEST RESULTS 25 9 . PEAK OUTPUT POWER TEST 26 9.1 APPLIED PROCEDURES / LIMIT 26 9.1.1 TEST PROCEDURE 26 9.1.2 DEVIATION FROM STANDARD 26 9.1.3 TEST SETUP 26 9.1.4 EUT OPERATION CONDITIONS 26 9.1.5 EUT TEST CONDITIONS 26 9.1.6 TEST RESULTS 26 10 . ANTENNA CONDUCTED SPURIOUS EMISSION 27 10.1 APPLIED PROCEDURES / LIMIT 27 10.1.1 TEST PROCEDURE 27 10.1.2 DEVIATION FROM STANDARD 27 10.1.3 TEST SETUP 27 10.1.4 EUT OPERATION CONDITIONS 27 10.1.5 EUT TEST CONDITIONS 27 10.1.6 TEST RESULTS 27 11 . MEASUREMENT INSTRUMENTS LIST 28 Report No.: BTL-FICP-1-1501C124 Page 5 of 115 Table of Contents Page 12 . EUT TEST PHOTO 30 ATTACHMENT A - CONDUCTED EMISSION 34 ATTACHMENT B - RADIATED EMISSION (9KHZ-30MHZ) 37 ATTACHMENT C - RADIATED EMISSION (30MHZ TO 1000MHZ) 39 ATTACHMENT D - RADIATED EMISSION (ABOVE 1000MHZ) 52 ATTACHMENT E - NUMBER OF HOPPING CHANNEL 77 ATTACHMENT F - AVERAGE TIME OF OCCUPANCY 79 ATTACHMENT G - HOPPING CHANNEL SEPARATION MEASUREMENT 92 ATTACHMENT H - BANDWIDTH 97 ATTACHMENT I - PEAK OUTPUT POWER 102 ATTACHMENT J - ANTENNA CONDUCTED SPURIOUS EMISSION 107 Report No.: BTL-FICP-1-1501C124 Page 6 of 115 REPORT ISSUED HISTORY Issued No. Description Issued Date BTL-FICP-1-1501C124 Original Issue. Jan. 28, 2015 Report No.: BTL-FICP-1-1501C124 Page 7 of 115 1. CERTIFICATION Equipment : Sound Kick 2 Brand Name : Model Name : SFQ-11 Applicant Beautiful Enterprise Co., Ltd. Manufacturer : Beautiful Enterprise Co., Ltd. Address : 27th Floor, Beautiful Group Tower, 77 Connaught Road Central, Hong Kong Factory : Shenzhen Synchron Electronics Co., Ltd. Address : No. 9 Mei Li Road, Xia Mei Lin, Fu Tian Area, Shenzhen, Guangdong, China Date of Test : Jan. 19, 2015 ~ Jan. 27, 2015 Test Sample : ENGINEERING SAMPLE Standard(s ) : FCC Part15, Subpart C : 2013 (15.247) / ANSI C63.4 : 2009 / FCC Public Notice DA 00-705, Mar…

Text truncated - open the document above for the full version.

Report No.: BTL-FICP-1-1501C124 Page 30 of 115 12. EUT TEST PHOTO Conducted Measurement Photos Report No.: BTL-FICP-1-1501C124 Page 31 of 115 Radiated Measurement Photos 9KHz to 30MHz Report No.: BTL-FICP-1-1501C124 Page 32 of 115 Radiated Measurement Photos 30MHz to 1000MHz Report No.: BTL-FICP-1-1501C124 Page 33 of 115 Radiated Measurement Photos Above 1000MHz