V65E4520CDMA/GSM Flip Phone

Important Safety Information 1 This section contains important operational and safety information that will help you safely use your phone. Failure to read and follow the information provided in this section may result in serious bodily injury, death, or property damage. There are several simple guidelines to operating your phone properly and maintaining safe, satisfactory service. ●To maximize performance, do not touch the portions of your phone where the internal antennas are located while using the phone. ●Speak directly into the mouthpiece. ●Do not expose your phone to direct sunlight for extended periods of time (such as on the dashboard of a car). ●Although your phone is quite sturdy, it is a complex piece of equipment and can be broken. Avoid dropping, hitting, bending, or sitting on it. ●Any changes or modifications to your phone not expressly approved in this document could void your warranty for this equipment and void your authority to operate this equipment. Important Safety Information General Precautions 2 Important Safety Information Note:For the best care of your phone, only Kyocera-authorized personnel should service your phone and accessories. Failure to do so may be dangerous and void your warranty. Do Not Rely on Your Phone for Emergency Calls Mobile phones operate using radio signals, which cannot guarantee connection in all conditions. Therefore you should never rely solely upon any mobile phone for essential communication (e.g., medical emergencies). Emergency calls may not be possible on all cellular networks or when certain network services or mobile phone features are in use. Check with your local service provider for details. Using Your Phone While Driving Talking on your phone while driving (or operating the phone without a hands-free device) is prohibited in some jurisdictions. Laws vary as to specific restrictions. Remember that safety always comes first. Maintaining Safe Use of and Access to Your Phone Important Safety Information 3 Following Safety Guidelines To operate your phone safely and efficiently, always follow any special regulations in a given area. Turn your phone off in areas where use is forbidden or when it may cause interference or danger. Medical Devices If you have a medical device, including an implantable medical device such as a pacemaker or defibrillator, consult your healthcare provider and the device manufacturer’s directions before using this mobile phone. Persons with implantable medical devices: ●Should always keep the mobile phone more than six (6) inches from the implantable medical device when the mobile phone is turned ON. ●Should not carry the mobile phone in the breast pocket. ●Should use the ear opposite the implantable medical device to minimize the potential for interference. ●Should turn OFF the mobile phone immediately if you have any reason to suspect that interference is taking place. 4 Important Safety Information Using Your Phone Near Other Electronic Devices Most modern electronic equipment is shielded from radio frequency (RF) signals. However, RF signals from wireless phones may affect inadequately shielded electronic equipment. RF signals may affect improperly installed or inadequately shielded electronic operating systems or entertainment systems in motor vehicles. Check with the manufacturer or their representative to determine if these systems are adequately shielded from external RF signals. Also check with the manufacturer regarding any equipment that has been added to your vehicle. Consult the manufacturer of any personal medical devices, such as pacemakers and hearing aids, to determine if they are adequately shielded from external RF signals. Note:Always turn off the phone in healthcare facilities, and request permission before using the phone near medical equipment. Using Your Phone On Airplanes On airplanes, follow applicable airline regulations and always follow the flight crew’s instructions concerning the use of your phone. Important Safety Information 5 Turning Off Your Phone in Dangerous Areas To avoid interfering with blasting operations, turn your phone off when in a blasting area or in other areas with signs indicating two-way radios should be turned off. Construction crews often use remote- control RF devices to set off explosives. Turn your phone off when you’re in any area that has a potentially explosive atmosphere. Although it’s rare, your phone and accessories could generate sparks. Sparks can cause an explosion or fire, resulting in bodily injury or even death. These areas are often, but not always, clearly marked. They include: ●Fueling areas such as gas stations. ●Below deck on boats. ●Fuel or chemical transfer or storage facilities. ●Areas where the air contains chemicals or particles such as grain, dust, or metal powders. ●Any other area where you would normally be advised to turn off your vehicle’s engine. Note:Never transport or store flammable gas, flammable liquids, or explosives in the compartment of your vehicle that contains your phone or accessories. Note:Your phone complies with the Standards for Hazardous Location Equipment. Refer to the following section ‘Using Your Phone in Hazardous Locations’ for details. 6 Important Safety Information Using Your Phone in Hazardous Locations Your phone complies with the Standards for Hazardous Location Equipment as a Nonincendive Electrical Equipment for use in a Class I, Division 2, Groups A, B, C & D with a Temperature Code of T4. Precautions ●Ensure that your phone is not exposed to the temperature outside the limits stated below. ▪Ambient Temperature: -22° F to 140° F (-30° C to 60° C) ▪Charging Temperature: 32° F to 122° F (0° C to 50° C) ▪Storage Temperature: -40° F to 185° F (-40° C to 85° C) ●Do not charge your phone in Division 2 hazardous locations. ●Use only the charger provided with your phone: battery charger SCP-45ADT and USB data cable SCP-18SDC. ●The audio jack, charger/data port, and battery covers must be properly seale…

Text truncated - open the document above for the full version.

KYOCERA Communications, Inc 9520 Towne Centre Drive, Suite #200 San Diego, 92121 Phone: 858-882-1400 FAX: 858-450-0134 Date: October 17, 2014 To whom it may concern, Please be notified that I, Douglas Dunn, have designated Daniel Lee of Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch (BV CPS Taoyuan Branch) of Taiwan as the person being responsible for this project and to sign the form 731 and other documentation. Any and all acts carried out by Daniel Lee of Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch (BV CPS Taoyuan Branch) of Taiwan on the matters relating to all processes required in the FCC approval and any communication needed with the national authority, shall have the same legal authority as acts on our own behalf. As defined in 47 CFR Ch. 1.2002 (b), we further certify that neither the applicant nor any party to this application is subject to a denial to Federal benefits, including FCC benefits, pursuant to section 5301 of the Anti-Drug Abuse Act of 1998, 21 U.S.C. 835(a). This authorization is limited to the product of as following: FCC ID: V65E4520 If you have any acknowledgement and response, please send it to Daniel Lee of Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch (BV CPS Taoyuan Branch) of Taiwan directly. Should you have any question or comment regarding this matter, please do not hesitate to contact me. Sincerely yours, Douglas Dunn Director of Regulatory Affairs Kyocera Communications, Inc.

KYOCERA Communications, Inc 9520 Towne Centre Drive, Suite #200 San Diego, 92121 Phone: 858-882-1400 FAX: 858-450-0134 Date: October 17, 2014 Federal Communications Commission 7345 Oakland Mills Road Columbia MD21046 Subject: Request for Confidentiality FCC ID: V65E4520 To Whom It May Concern, Pursuant to the provisions of Sections 0.457 and 0.459 of Commission’s rules (47CFR§§0.457, 0.459), we are requesting the Commission to withhold the following attachments as confidential document from public disclosure indefinitely. l Schematic Diagram l Block Diagram l Parts List l Tune-up Procedure l Operational Description The above mentioned documents contain detailed system and equipment descriptions that are considered to be proprietary information in the operation of the equipment. The public disclosure of above documents might be harmful to our company and would give competitors an unfair advantage in the market. In addition to the above mentioned documents, pursuant to Public Notice DA 04-1705 of the Commission’s policy, in order to comply with the marketing regulations in 47 CFT §2.803 and the importation rules in 47 CFR §2.1204, while ensuring that business sensitive information remains confidential until the actual marketing of newly authorized devices. We are requesting the commission to grant short-term confidentiality request on the following attachments until 180 days after the Grant Date of Equipment Authorizations. u External Photos u Internal Photos u Test Setup Photos u Users Manual It is our understanding that all measurement test reports, FCC ID label format and correspondence during certification review process cannot be granted as confidential documents and those information will be available for public review once the grant of equipment authorization is issued. Best regards, Douglas Dunn Director of Regulatory Affairs Kyocera Communications, Inc.

KYOCERA Communications, Inc 9520 Towne Centre Drive, Suite #200 San Diego, 92121 Phone: 858-882-1400 FAX: 858-450-0134 Date: October 17, 2014 Federal Communications Commission Authorization and Evaluation Division 7345 Oakland Mills Road Columbia MD 21046 SUBJECT: FCC Application for FCC ID: V65E4520 To Whom It May Concern, We, Kyocera Corporation, hereby attest to the fact that we will apply the Declaration of Conformity procedure to the class B computer peripheral portion of this composite filing. Sincerely yours, Douglas Dunn Director of Regulatory Affairs Kyocera Communications, Inc.

KYOCERA Communications, Inc 9520 Towne Centre Drive, Suite #200 San Diego, 92121 Phone: 858-882-1400 FAX: 858-450-0134 Date: October 17, 2014 Statement We, Kyocera Corporation, state that there is no other space to put the label on our device, FCC ID: V65E4520, except for the space in the battery compartment of this device. The label will be put in the battery compartment, and it is visible to the users as they purchase the product and install the battery. If you have any question regarding this declaration, please don’t hesitate to contact me. Sincerely yours, Douglas Dunn Director of Regulatory Affairs Kyocera Corporation c / o Kyocera Communications, Inc. Fax: 858-882-2010 Tel: 858-882-2117 E-mail: [email protected]

Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch 香港商立德國際商品試驗有限公司 桃園分公司 No. 19, Hwa Ya 2nd Rd., Wen Hwa Tsuen, Kwei Shan Hsiang, Taoyuan Hsien 33383, Taiwan TEL: 886-3-3183232 FAX: 886-3-3270892 http://www.adt.com.tw / E-mail: [email protected] Date: October 31, 2014 SUBJECT: Supersede for FCC ID: V65E4520, Granted Date: 10/28/2014 To Whom It May Concern: We, Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch., hereby declare on our client’s behalf that the original submitted SAR test report and Tune-up Procedure should be superseded due to some typo of the tune-up tolerance on GSM 1900(EDGE). The superseded documents are listed as below: Original File name Newly File name V65E4520_test rpt_RF Exposure Info (SAR).PDF V65E4520_test rpt_RF Exposure Info (SAR)_R1.PDF V65E4520_tech_Tune up Procedure.PDF V65E4520_tech_Tune up Procedure_R1.PDF Except for the change above, no other modification is performed. Also, the change does not have any impact on the approved radio parameter such as power, frequency range, modulation etc. Should you have any question or comment regarding this matter, please do not hesitate to contact me. Sincerely yours, Daniel Lee / Vice President Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch Tel: 886-3-318 3232 ext. 1857 Fax: 886-3-318 5050 Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch 香港商立德國際商品試驗有限公司 桃園分公司 No. 19, Hwa Ya 2nd Rd., Wen Hwa Tsuen, Kwei Shan Hsiang, Taoyuan Hsien 33383, Taiwan TEL: 886-3-3183232 FAX: 886-3-3270892 http://www.adt.com.tw / E-mail: [email protected]

Page 1 CONSTRUCTION PHOTOS OF EUT Page 2 Page 3 Page 4 Page 5

V65E4520

FCC ID: V65E4520 Battery Compartment Label Location is under battery compartment

Page 6 Page 7 Page 8 Page 9 Page 10 Page 11 Page 12 Page 13 Page 14 Page 15 Page 16

Report No.: RF140916C16-2 1 of 45 Report Format Version 5.1.0 FCC TEST REPORT (BLUETOOTH) REPORT NO.: RF140916C16-2 MODEL NO.: E4520 FCC ID: V65E4520 RECEIVED: Sep. 16, 2014 TESTED: Sep. 29, 2014 ~ Oct. 02, 2014 ISSUED: Oct. 13, 2014 APPLICANT: Kyocera Corporation c/o Kyocera Communications ADDRESS: 9520 Towne Centre Drive, Suite #200, San Diego, California 92121 ISSUED BY: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch LAB ADDRESS: No. 47-2, 14th Ling, Chia Pau Vil., Lin Kou Dist., New Taipei City, Taiwan ( R.O.C ) TEST LOCATION: No. 19, Hwa Ya 2nd Rd, Wen Hwa Tsuen, Kwei Shan Hsiang, Taoyuan Hsien 333, Taiwan, R.O.C. This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the compliance or non-compliance to the specification. This report should not be used by the client to claim product certification, approval, or endorsement by TAF or any government agencies. Report No.: RF140916C16-2 2 of 45 Report Format Version 5.1.0 TABLE OF CONTENTS RELEASE CONTROL RECORD ..............................................................................................................4 1. CERTIFICATION ..................................................................................................................................5 2. SUMMARY OF TEST RESULTS .........................................................................................................6 2.1 MEASUREMENT UNCERTAINTY...............................................................................................6 3. GENERAL INFORMATION ..................................................................................................................7 3.1 GENERAL DESCRIPTION OF EUT ............................................................................................7 3.2 DESCRIPTION OF TEST MODES ..............................................................................................8 3.2.1 TEST MODE APPLICABILITY AND TESTED CHANNEL DETAIL .................................9 3.3 DESCRIPTION OF SUPPORT UNITS ...................................................................................... 11 3.3.1 CONFIGURATION OF SYSTEM UNDER TEST .......................................................... 11 3.4 GENERAL DESCRIPTION OF APPLIED STANDARDS .......................................................... 12 4. TEST TYPES AND RESULTS (FOR BLUETOOTH EDR) ............................................................... 13 4.1 RADIATED EMISSION AND BANDEDGE MEASUREMENT .................................................. 13 4.1.1 LIMITS OF RADIATED EMISSION AND BANDEDGE MEASUREMENT ................... 13 4.1.2 TEST INSTRUMENTS ................................................................................................. 14 4.1.3 TEST PROCEDURES ................................................................................................. 15 4.1.4 DEVIATION FROM TEST STANDARD ....................................................................... 15 4.1.5 TEST SETUP ............................................................................................................... 16 4.1.6 EUT OPERATING CONDITIONS ................................................................................ 17 4.1.7 TEST RESULTS........................................................................................................... 18 4.2 CONDUCTED EMISSION MEASUREMENT ........................................................................... 22 4.2.1 LIMITS OF CONDUCTED EMISSION MEASUREMENT ........................................... 22 4.2.2 TEST INSTRUMENTS ................................................................................................. 22 4.2.3 TEST PROCEDURES ................................................................................................. 23 4.2.4 DEVIATION FROM TEST STANDARD ....................................................................... 23 4.2.5 TEST SETUP ............................................................................................................... 24 4.2.6 EUT OPERATING CONDITIONS ................................................................................ 24 4.2.7 TEST RESULTS........................................................................................................... 25 4.3 NUMBER OF HOPPING FREQUENCY USED ........................................................................ 27 4.3.1 LIMIT OF HOPPING FREQUENCY USED ................................................................. 27 4.3.2 TEST SETUP ............................................................................................................... 27 4.3.3 TEST INSTRUMENTS ................................................................................................. 27 4.3.4 TEST PROCEDURE ...........................................…

Text truncated - open the document above for the full version.

1 PHOTOGRAPHS OF THE TEST CONFIGURATION CONDUCTED EMISSION TEST (For Bluetooth) 2 RADIATED EMISSION TEST (For Bluetooth) 3 (WWAN) (PART 22) RADIATED EMISSION TEST (GSM/EDGE) 4 RADIATED EMISSION TEST (CDMA) 5 ERP POWER TEST 6 (PART 24) RADIATED EMISSION TEST 7 EIRP POWER TEST