VIQ-KANATONAIS AtoN (Aids-to-Navigation)

Orolia S.A.S. Z.I. des Cinq Chemins 56520 GUIDEL - FRANCE Telephone: +33 (0)2 97 02 49 49 Fax: +33 (0)2 97 65 00 20 Web : http://www.mcmurdomarinesystems.com An Orolia Group Business REF. : DOC10089 INDICE : D DATE : 14/05/2014 KanAtoN 1 / 3 AIS Transponder Installation Manual Radio Frequency Exposure Warning WARNING: The AIS transmitter is a radio transmitter which emits radio frequency radiation when activated. When transmitting, the user’s minimum distance of exposure is 1 meter. FCC notice This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to part15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. KanAtoN 3 AIS Transponder Manuel d’installation PAGE : TOC 1 / 1 DATE : 14/05/2014 INDICE : D REF. : DOC10089 TABLE OF CONTENTS 1. Product definition ........................................................................................................ 1 1.1. Purpose .................................................................................................................. 1 1.2. Main components included in the KanAtoN 3 AIS .............................................. 1 1.2.1. Before installing KanAtoN 3 AIS Transponder .................................................. 1 1.2.2. Inventory ........................................................................................................... 1 1.3. Description ............................................................................................................. 2 1.3.1. General description ........................................................................................... 2 1.3.2. Dome ................................................................................................................ 2 1.3.3. Mechanical interfaces ....................................................................................... 3 1.3.4. Electrical interfaces ........................................................................................... 3 2. Installation procedure ................................................................................................. 4 2.1. Installation Precautions ........................................................................................ 4 2.2. Mounting on a mast or hard rail ........................................................................... 5 2.3. Mounting on horizontal or vertical surface ......................................................... 6 2.4. Dome connection .................................................................................................. 6 2.5. Check of Installation ............................................................................................. 7 3. Working mode.............................................................................................................. 8 3.1. Position fixing ........................................................................................................ 8 3.2. Back up at configuration setting .......................................................................... 8 3.3. Events back up ...................................................................................................... 8 3.4. Working safety ....................................................................................................... 8 3.5. Serial interfaces ..................................................................................................... 8 3.6. On-going transmission ......................................................................................... 8 3.7. Update of software ................................................................................................ 8 3.8. Reception of meteorological and hydrological data .......................................... 9 3.9. Reception of technical data .................................................................................. 9 3.10. Specification of TOR inputs .............................................................................. 9 3.11. Designation of TOR inputs ................................................................................ 9 3.12. Information output ............................................................................................10 4. Technical specifications ............................................................................................11 4.1. Environmental specifications ..............................................................................11 4.2. CEM specifications ...............................................................................................11 4.3. GPS receiver .........................................................................................................11 4.4. Antenna .................................................................................................................12 4.5. Consumption ........................................................................................................12 4.6. Function of configuration software « AIS-config.exe » .....................................12 5. Failures analysis.........................................................................................................13 5.1. Self-test ........................................…

Text truncated - open the document above for the full version.

EXTERNAL PHOTOS Référence : BABT14 Indice : A Date : 30/07/13 Page : 1/1

FCC ID ARTWORK Référence : BABT07 Indice : A Date : 30/07/13 Page : 1/1 FCC ID : VIQ-KANATON

LABEL LOCATION Référence : BABT08 Indice : A Date : 30/07/13 Page : 1/1

INTERNAL PHOTOS Référence : BABT15 Indice : A Date : 30/07/13 Page : 1/2 Dome with top view of the PCB Bottom view of the PCB INTERNAL PHOTOS Référence : BABT15 Indice : A Date : 30/07/13 Page : 2/2 Dome without the PCB – View of the resin used to ensure sealing of the product Bottom view of the product Ground connection Antenna cable Data cable Power Supply cable Power supply + RS232 RS485 VHF antenna Ground

Document 75925284 Report 01 Issue 1 March 2014 Report On FCC Testing of the Orolia SAS KanAtoN3 In accordance with FCC CFR 47 Part 15B COMMERCIAL-IN-CONFIDENCE FCC ID: VIQ-KANATON TÜV SÜD Product Service, Octagon House, Concorde Way, Segensworth North, Fareham, Hampshire, United Kingdom, PO15 5RL Tel: +44 (0) 1489 558100. Website: www.tuv-sud.co.uk COMMERCIAL-IN-CONFIDENCE Document 75925284 Report 01 Issue 1 Page 1 of 16 COMMERCIAL-IN-CONFIDENCE REPORT ON FCC Testing of the Orolia SAS KanAtoN3 In accordance with FCC CFR 47 Part 15B Document 75925284 Report 01 Issue 1 March 2014 PREPARED FOR Orolia SAS Z.I des 5 Chemins CS 10028 56520 Guidel France PREPARED BY Natalie Bennett Senior Administrator, Technical Solutions APPROVED BY Simon Bennett Authorised Signatory DATED 17 March 2014 ENGINEERING STATEMENT The measurements shown in this report were made in accordance with the procedures described on test pages. All reported testing was carried out on a sample equipment to demonstrate limited compliance with FCC CFR 47 Part 15B. The sample tested was found to comply with the requirements defined in the applied rules. Test Engineer(s); G Lawler Document 75925284 Report 01 Issue 1 Page 2 of 16 COMMERCIAL-IN-CONFIDENCE COMMERCIAL-IN-CONFIDENCE CONTENTS Section Page No 1 REPORT SUMMARY ................................................................................................................... 3 1.1 Introduction ................................................................................................................................... 4 1.2 Brief Summary of Results ............................................................................................................. 5 1.3 Declaration of Build Status ........................................................................................................... 6 1.4 Product Information ...................................................................................................................... 7 1.5 Test Conditions ............................................................................................................................. 7 1.6 Deviations from the Standard ....................................................................................................... 7 1.7 Modification Record ...................................................................................................................... 7 2 TEST DETAILS ............................................................................................................................ 8 2.1 Radiated Emissions ...................................................................................................................... 9 3 TEST EQUIPMENT USED ......................................................................................................... 12 3.1 Test Equipment Used ................................................................................................................. 13 3.2 Measurement Uncertainty .......................................................................................................... 14 4 ACCREDITATION, DISCLAIMERS AND COPYRIGHT ............................................................ 15 4.1 Accreditation, Disclaimers and Copyright ................................................................................... 16 Document 75925284 Report 01 Issue 1 Page 3 of 16 COMMERCIAL-IN-CONFIDENCE COMMERCIAL-IN-CONFIDENCE SECTION 1 REPORT SUMMARY FCC Testing of the Orolia SAS KanAtoN3 In accordance with FCC CFR 47 Part 15B Document 75925284 Report 01 Issue 1 Page 4 of 16 COMMERCIAL-IN-CONFIDENCE COMMERCIAL-IN-CONFIDENCE 1.1 INTRODUCTION The information contained in this report is intended to show verification of the FCC Testing of the Orolia SAS KanAtoN3 to the requirements of FCC CFR 47 Part 15B. Objective To perform FCC Testing to determine the Equipment Under Test's (EUT’s) compliance with the Test Specification, for the series of tests carried out. Manufacturer Orolia SAS Model Number(s) Kan AtoN3 Serial Number(s) LX1200023441 Number of Samples Tested 1 Test Specification/Issue/Date FCC CFR 47 Part 15B (2013) Incoming Release Date Declaration of Build Status 17 March 2014 Disposal Reference Number Date Held Pending Disposal Not Applicable Not Applicable Order Number Date 1400012 10 January 2014 Start of Test 5 March 2014 Finish of Test 5 March 2014 Name of Engineer(s) G Lawler Related Document(s) ANSI C63.4 (2003) Document 75925284 Report 01 Issue 1 Page 5 of 16 COMMERCIAL-IN-CONFIDENCE COMMERCIAL-IN-CONFIDENCE 1.2 BRIEF SUMMARY OF RESULTS A brief summary of the tests carried out in accor dance with FCC CFR 47 Part 15B is shown below. Section Spec Clause Test Description Result Comments/Base Standard Idle 2.1 15.109 Radiated Emissions Pass ANSI C63.4 (2003) Document 75925284 Report 01 Issue 1 Page 6 of 16 COMMERCIAL-IN-CONFIDENCE COMMERCIAL-IN-CONFIDENCE 1.3 DECLARATION OF BUILD STATUS Document 75925284 Report 01 Issue 1 Page 7 of 16 COMMERCIAL-IN-CONFIDENCE COMMERCIAL-IN-CONFIDENCE 1.4 PRODUCT INFORMATION 1.4.1 Technical Description The Equipment Under Test (EUT) was a Orolia SAS KanAtoN3. A full technical description can be found in the manufacturer’s documentation. 1.5 TEST CONDITIONS For all tests the EUT was set up in accordance with the relevant test standard and to represent typical operating conditions. Tests were applied with the EUT situated in a shielded enclosure. The EUT was powered from a 24 V DC supply. FCC Measurement Facility Registration Number 90987 Octagon House, Fareham Test Laboratory 1.6 DEVIATIONS FROM THE STANDARD No deviations from the applicable test standard were made during testing. 1.7 MODIFICATION RECORD Modification 0 - No modifications were made to the test sample during testing. Document 75925284 Report 01 Issue 1 Page 8 of 16 COMMERCIAL-IN-CONFIDENCE COMMERCIAL-IN-CONFIDENCE SECTION 2 TEST DETAILS FCC Testing of the Orolia SAS KanAtoN3 In accordance with FCC CFR 47 Part 15…

Text truncated - open the document above for the full version.

TEST SETUP Référence : BABT17 Indice : A Date : 30/07/13 Page : 1/1