VO5SM-062Bluetooth Headset

BlueTooth SMY TM SM-M062 http://www.sanmy.hk z z z z 2.0/ z z z 5.5VDC~6VDC z 10~20() z z -1545 z / z 3 z 3 z () z z 3 z ,, z SM-M062,,, z 0000(4), z z ,2, z z 2 z z , z // z 10,, BlueTooth SMY TM SM-062 BLUETOOTH MANUAL SM-062 User’s Guide DRIVING SAFETY When you are driving a car, driving is your first responsibility. when using your headset while driving ,follow your local regulations in the country or region you are in. BEFORE USING YOUR HEADSET 1.Checking phone compatibility. 2.Headset is compatible with most bluetooth phones and bluetooth version 2.0 and support the headset and hands-free profiles ,ensure that your phone has bluetooth capability by visiting your phone manufacturers website. Your headset overview CHARGING THE HEADSET 1.Headset uses a rechargeable battery , must chare the battery fully before using headset for the first time. 2. The charger must be matched with the original manufacturer’s mold. 3.The voltage should between 5.5VDC~6.0VDC. 4.The blue indicator light displayed during changing ,when the indicator light turns off, that is fully charged. NOTICE: When keep the headset for long time no use. It’s normal that the indicator will not display while after 10—20 minutes start to display. STORAGE OF THE HEADSET 1.Always storage the headset with be off and make sure it is safely protected. 2.Avoid storage at high temperatures(between-15~45). 3.Do not expose the headset or any of its supplied parts to rain or other liquids . SWITCHING THE HEADSET ON OR OFF To switch on ,press the multi-function key for about 3 seconds. until the blue indicator turns on in lasting blue. To switch off ,press and hold for about 6 seconds. until the red indicator turns off. PAIRING WITH YOUR BLUETOOTH PHONE 1.Pairing will create a unique and encrypted wireless link between two Bluetooth enabled devices . 2.Ensure that the headset is the power off. 3.Press and hold the multi-function key until the indicator light turns on in blue and lasting blue. 4.Set your Bluetooth phone to discover the headset by following your phone’s guide ,typically ,the steps involve going to a ‘ setup’ ‘connect’ or ‘Bluetooth’ menu on your phone and then selecting the option to discover Bluetooth devices. 5.Your phone will find the SM-062 headset and ask if you want to pair with is. confirm this by pressing the yes or ok key . 6.Enter a passkey or PIN,0000(4 zero) the press the yes or ok key . 7:Select the “connect”, then start to create a connect between the headset and mobile. IMPORTANANT If pairing is successful ,the indicator light will turns to be in blue in every 2 seconds. If unsuccessful ,the light remains on ,and you will need to re-attempt pairing . MAKING A CALL Make sure the headset has been connected with the phone already. Then make a call as usual by your phone REDIALLING THE LAST NUMBER Press the multi-function key fleetly , twice. ENDING A CALL Press the multi-function key ,once. ANSWERING A CALL After you hearing the ring tone ,press the multi-function key once. ADJUSTING THE VOLUME Please adjust the volume from the volume key or your mobile. Notice: The operation range is about 10m. pairing a unique link between Bluetooth and pone. Please keep away from the wireless devices when you are calling, it will not interfere with any other electric equipments . *** Caution *** This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes of modifications not expressly approved by the party responsible for compliance could void the user ’s authority to operate the equipment. FCC statement Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: --Reorient or relocate the receiving antenna. --Increase the separation between the equipment and receiver. --Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. --Consult the dealer or an experienced radio/TV technician for help.

R O M R A M B a s e b a n d D SP C P U 2.4GHz Radio I/O F il t e r Y 1 = 16 M H z SP I UA R T / U S B P I O P C M A u d i o I n / O u t B a tt e r y C h a r g e r B u tt on M i c r o p hon e S p ea k e r B a tt e r y B u l e T oo t h H ea d s e t E l ec t r o c i r c u i t C h a r t

External Photos

Page 1 of 2 Internal Photos Page 2 of 2

Operation Description The SM-062 use the Bluetooth Technology to connect with Mobile which have built in Bluetooth .Using the HFP&profile of Bluetooth to have call function. The following is the function subject: 1 receive call 2 end call 3 volume control 4 last num redial 5 active the voice dialing when mobile support this function The function theory as below: 1 function diagram 2 The Mobile Wireless Headset uses a short-range wireles communication Technology. The design applied is in international identification ISM (Industrial Scientific and Medical )frequency bandwidth environment that is 2.4GHz—2.48GHz bandwidth. 3 The Mobile Wireless Headset is a wireless mono headset Within a range of 10 meters, This headest can connect to other Bluetooth devices which have built-in audio gateway,such as Mobile Phone,Desktop,Notebook Computer or PDA etc...

桌面 实测 实测 实测

SHENZHEN SETEK TECHNOLOGY CO., LTD. Report No.:SE08FCI050R FCC TEST REPORT REPORT NO.:SE08FCI050R MODEL NO.: SM-062 RECEIVED: Feb 29, 2008 TESTED: Feb 29, 2008 to Mar 05, 2008 APPLICANT: SANMY TECHNOLOGY CO., LTD ADDRESS: No6, Hesheng Industrial Area, Heping High Tech Zone, Fuyong Town, Shenzhen, China ISSUED BY: SHENZHEN SETEK TECHNOLOGY CO., LTD. LAB LOCATION: 2/F,A3 Bldg,East Industry Zone,Overseas Chinese Town, Shenzhen,China This test report consists of 56 pages in total, it may be duplicated completely for legal use with the approval of the applicant, It should not be reproduced except in full, without the written approval of our laboratory, The test results in the report only apply to the tested sample. SHENZHEN SETEK TECHNOLOGY CO., LTD. Our website: www.setek.com.cn E-mail:[email protected] TEL:86-755-26966362 FAX: 86-755-26966270 SHENZHEN SETEK TECHNOLOGY CO., LTD. Report No.:SE08FCI050R Page 2 of 56 The device described above is tested by SHENZHEN SETEK TECHNOLOGY CO., LTD. to determine the maximum emission levels emanating from the device and the severe levels of the device can endure and its performance criterion. This report applies to above tested sample only and shall not be reproduced in part without written approval of SHENZHEN SETEK TECHNOLOGY CO., LTD. Prepared for : SANMY TECHNOLOGY CO., LTD Address : No6, Hesheng Industrial Area, Heping High Tech Zone, Fuyong Town, Shenzhen, China Product : Bluetooth Earphone Model No. : SM-062 Trademark : SMY Test Standard : FCC Part 15 Paragraph 15.203, Paragraph 15.207 and Paragraph 15.247 Prepared by : SHENZHEN SETEK TECHNOLOGY CO., LTD. Address : 2/F, A3 Bldg, East Industry Zone, Overseas Chinese Town, Shenzhen, China FCC Registration Number: 966959 Tel: (86-755) 26966362 Fax:(86-755) 26966270 Prepared by : (Engineer) Reviewer by : (Project Engineer) Approved by : (Manager) Report Number : SE08FCI050R Date of Test : Feb 29, 2008 to Mar 05, 2008 Date of Report : Mar 05, 2008 SHENZHEN SETEK TECHNOLOGY CO., LTD. Report No.:SE08FCI050R Page 3 of 56 TABLE OF CONTENTS Description Page The Report Description 1. GENERAL INFORMATION ............................................................................................................ 5 1.1. Description of Device (EUT) ....................................................................................................................5 1.2. Description of Support Device..................................................................................................................6 1.3. Summary of test results.............................................................................................................................6 1.4. List of Measuring Equipments Used.........................................................................................................7 1.5. Test Facility ..............................................................................................................................................7 1.6. Measurement Uncertainty .........................................................................................................................7 2. ANTENNA REQUIREMENT ......................................................................................................... 8 2.1. Standard Applicable..................................................................................................................................8 2.2. Antenna Connected Construction .............................................................................................................8 3. POWER LINE CONDUCTED MEASUREMENT ....................................................................... 9 3.1. Test Equipment .........................................................................................................................................9 3.2. Block Diagram of Test Setup....................................................................................................................9 3.3. Power Line Conducted Emission Measurement Limits(Class B) .............................................................9 3.4. Configuration of EUT on Measurement .................................................................................................10 3.5. Operating Condition of EUT ..................................................................................................................10 3.6. Test Procedure ........................................................................................................................................10 3.7. Power Line Conducted Emission Measurement Results ........................................................................10 4. TEST OF HOPPING CHANNEL BANDWIDTH....................................................................... 13 4.1 Applicable Standard .......................................................................................................................................13 4.2 EUT Setup ......................................................................................................................................................13 4.3 Test Equipment List and Details ....................................................................................................................13 4.4 Test Procedure................................................................................................................................................13 4.5 Test Result......................................................................................................................................................13 5. TEST OF HOPPING CHANNEL SEPARATION ...................................................................... 17 5.1 Applicable Standard .......................................................................................................................................17 5.2 EUT Setup ...........................................................................…

Text truncated - open the document above for the full version.

Radiated Emission Setup Photo