VUI-CFWMCustomer Facing Wi-Fi Module (CFWM)

Confidential CUSTOMER FACING WI-FI MODULE (CFWM) Model No: 84911790C Confidential CFWM IO Connector Placement ComboD/ CON2 QHFM-C WiFi ComboD/ CON6 QHFM-A LTE1+GNSS ComboA/ CON10 AptivAMEC 3port ComboB/ CON9 AptivAMEC 8+2port ComboC/ CON8 Molex MX150 20pin Confidential CFWM FEATURE SET The Customer Facing Wi-Fi Module(CFWM) is a stripped down version of Telematics & Net-work Gateway (TANG). The CFWM shares the same platform as TANG but with only 1 LTE modem and addition Bluetooth function. It runs on the public network side and interact with customer providing exceptional in-car expe-riences. The module also serves as the communication anchor for IDCM(Internal Display Con-trolModule) and the in-cabin displays to keep the infotainment system separate from the AV se-cure network while maintaining the connectivity. Key features: The CFWM serves as the Wi-Fi hotspot for customer to allow high speed streaming. The CFWM supports audio and video streaming between the AV and the customer's mo-bile devices. The CFWM also connects to Cruise cloud securely to run the speech recognition engine for voice assistance. Confidential Federal Communication Commission Interference Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interferencewill not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment offand on, the user is encouraged to try to correct the interference by one of the following measures: -Reorient or relocate the receiving antenna. -Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from thatto which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This device meets all the other requirements specified in Part 15E, Section 15.407 of the FCC Rules. FOR PORTABLE DEVICE USAGE (<20m from body/SAR needed) Radiation ExposureStatement: The product comply with the FCC portable RF exposure limit set forth for an uncontrolled environment and are safe for intended operation as described in this manual. The further RF exposure reduction can be achieved if the product can be kept as far as possible from the user body or set the device to lower output power if such function is available. This equipment should be installed and operated with minimum distance 41mm between the radiator& your body.

Reference No.: BDTL-WTW-P21060470_EXT Page No. 1 / 5 CONSTRUCTION PHOTOS OF EUT Brand: , Model: 84911790C Reference No.: BDTL-WTW-P21060470_EXT Page No. 2 / 5 Reference No.: BDTL-WTW-P21060470_EXT Page No. 3 / 5 Reference No.: BDTL-WTW-P21060470_EXT Page No. 4 / 5 Reference No.: BDTL-WTW-P21060470_EXT Page No. 5 / 5

Reference No.: BDTL-WTW-P21060470_INT Page No. 1 / 9 CONSTRUCTION PHOTOS OF EUT Brand: , Model: 84911790C Reference No.: BDTL-WTW-P21060470_INT Page No. 2 / 9 Reference No.: BDTL-WTW-P21060470_INT Page No. 3 / 9 Reference No.: BDTL-WTW-P21060470_INT Page No. 4 / 9 Reference No.: BDTL-WTW-P21060470_INT Page No. 5 / 9 Antenna_LTE/GNSS (Model: 85004261) Reference No.: BDTL-WTW-P21060470_INT Page No. 6 / 9 Reference No.: BDTL-WTW-P21060470_INT Page No. 7 / 9 Antenna_CFWM WiFi (Model: 84623918) Reference No.: BDTL-WTW-P21060470_INT Page No. 8 / 9 Reference No.: BDTL-WTW-P21060470_INT Page No. 9 / 9

SAR Test Report Report Format Version 5.0.0 Page No. : 1 of 25 Report No. : SFBDTL-WTW-P22020360 Issued Date : Jun. 08, 2022 SAR Test Report Report No. : SFBDTL-WTW-P22020360 Applicant : PEGATRON CORPORATION Address : 5F, NO. 76, LIGONG ST., BEITOU DISTRICT, TAIPEI CITY 112, TAIWAN Product : Customer Facing Wi-Fi Module (CFWM) FCC ID : VUI-CFWM Brand : Model No. : 84911790C FCC Rule Part : 47 CFR §2.1093 Standards : IEEE Std 1528:2013, KDB 865664 D01 v01r04, KDB 865664 D02 v01r02, KDB 447498 D01 v06 IEC/IEEE 66209-1528:2020 KDB 248227 D01 v02r02 Sample Received Date : Feb. 15, 2022 Date of Testing : Mar. 22, 2022 ~ Mar. 23, 2022 Lab Address : No. 47-2, 14th Ling, Chia Pau Vil., Lin Kou Dist., New Taipei City, Taiwan Test Location : No. 19, Hwa Ya 2nd Rd., Wen Hwa Vil., Kwei Shan Dist., Taoyuan City, Taiwan CERTIFICATION: The above equipment have been tested by Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch–Lin Kou Laboratories, and found compliance with the requirement of the above standards. The test record, data evaluation & Equipment Under Test (EUT) configurations represented herein are true and accurate accounts of the measurements of the sample’s SAR characteristics under the conditions specified in this report. It should not be reproduced except in full, without the written approval of our laboratory. The client should not use it to claim product certification, approval, or endorsement by TAF or any government agencies. Prepared By : Vera Huang / Specialist Approved By : Gordon Lin / Manager FCC Accredited No.: TW0003 This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the compliance or non-compliance to the specification. SAR Test Report Report Format Version 5.0.0 Page No. : 2 of 25 Report No. : SFBDTL-WTW-P22020360 Issued Date : Jun. 08, 2022 Table of Contents Release Control Record ............................................................................................................................................................... 3 1. Summary of Maximum SAR Value ....................................................................................................................................... 4 2. Description of Equipment Under Test ................................................................................................................................. 5 3. SAR Measurement System ................................................................................................................................................... 6 3.1 Definition of Specific Absorption Rate (SAR) ............................................................................................................... 6 3.2 SPEAG DASY6 System ............................................................................................................................................... 6 3.2.1 Robot ............................................................................................................................................................... 7 3.2.2 Probes ............................................................................................................................................................. 8 3.2.3 Data Acquisition Electronics (DAE) .................................................................................................................. 8 3.2.4 Phantoms ......................................................................................................................................................... 8 3.2.5 Device Holder .................................................................................................................................................. 9 3.2.6 System Validation Dipoles ............................................................................................................................. 10 3.2.7 Power Source ................................................................................................................................................ 10 3.2.8 Tissue Simulating Liquids .............................................................................................................................. 11 3.3 SAR System Verification ............................................................................................................................................ 13 3.4 SAR Measurement Procedure ................................................................................................................................... 14 3.4.1 Area Scan and Zoom Scan Procedure .......................................................................................................... 14 3.4.2 Volume Scan Procedure ................................................................................................................................ 15 …

Text truncated - open the document above for the full version.

Plots of System Verification Annex A. Plots of System Verification The plots for system verification are shown as follows. Report No. : SFBDTL-WTW-P22020360 Plots of System Verification Test Laboratory: Bureau Veritas ADT SAR/HAC Testing Lab Date: 2022/03/23 S01 System Check_H2450_220323 DUT: Dipole 2450 MHz; Type: D2450V2; SN: 737 Communication System: UID 0, CW; Frequency: 2450 MHz;Duty Cycle: 1:1 Medium: H19T27N1_0323 Medium parameters used: f = 2450 MHz; σ = 1.832 S/m; ε r = 39.967; ρ = 1000 kg/m 3 Ambient Temperature：23.4 °C ; Liquid Temperature：23.1 °C DASY5 Configuration: - Probe: EX3DV4 - SN7537; ConvF(7.61, 7.61, 7.61) @ 2450 MHz; Calibrated: 2021/04/26 - Sensor-Surface: 1.4mm (Mechanical Surface Detection) - Electronics: DAE4 Sn1585; Calibrated: 2021/04/15 - Phantom: Twin-SAM V8.0_1988; Type: QD 000 P41 AA; - Measurement SW: DASY52, Version 52.10 (4); SEMCAD X Version 14.6.14 (7483) Pin=50mW/Area Scan (81x81x1): Interpolated grid: dx=1.200 mm, dy=1.200 mm Maximum value of SAR (interpolated) = 4.06 W/kg Pin=50mW/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = 48.87 V/m; Power Drift = -0.04 dB Peak SAR (extrapolated) = 5.01 W/kg SAR(1 g) = 2.41 W/kg; SAR(10 g) = 1.13 W/kg (SAR corrected for target medium) Maximum value of SAR (measured) = 4.06 W/kg Report No. : SFBDTL-WTW-P22020360 Plots of System Verification Test Laboratory: Bureau Veritas ADT SAR/HAC Testing Lab Date: 2022/03/22 S02 System Check_H5250_220322 DUT: Dipole 5 GHz; Type: D5GHzV2; SN: 1019 Communication System: UID 0, CW; Frequency: 5250 MHz;Duty Cycle: 1:1 Medium: H34T60N1_0322 Medium parameters used: f = 5250 MHz; σ = 4.828 S/m; ε r = 36.023; ρ = 1000 kg/m 3 Ambient Temperature：23.5 °C ; Liquid Temperature：23.2 °C DASY5 Configuration: - Probe: EX3DV4 - SN7537; ConvF(5.5, 5.5, 5.5) @ 5250 MHz; Calibrated: 2021/04/26 - Sensor-Surface: 1.4mm (Mechanical Surface Detection) - Electronics: DAE4 Sn1585; Calibrated: 2021/04/15 - Phantom: Twin-SAM V8.0_1988; Type: QD 000 P41 AA; - Measurement SW: DASY52, Version 52.10 (4); SEMCAD X Version 14.6.14 (7483) Pin=50mW/Area Scan (91x91x1): Interpolated grid: dx=1.000 mm, dy=1.000 mm Maximum value of SAR (interpolated) = 9.07 W/kg Pin=50mW/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=4mm, dy=4mm, dz=1.4mm Reference Value = 48.15 V/m; Power Drift = -0.04 dB Peak SAR (extrapolated) = 15.0 W/kg SAR(1 g) = 3.89 W/kg; SAR(10 g) = 1.16 W/kg (SAR corrected for target medium) Maximum value of SAR (measured) = 9.56 W/kg Report No. : SFBDTL-WTW-P22020360 Plots of System Verification Test Laboratory: Bureau Veritas ADT SAR/HAC Testing Lab Date: 2022/03/22 S03 System Check_H5600_220322 DUT: Dipole 5 GHz; Type: D5GHzV2; SN: 1019 Communication System: UID 0, CW; Frequency: 5600 MHz;Duty Cycle: 1:1 Medium: H34T60N1_0322 Medium parameters used: f = 5600 MHz; σ = 5.216 S/m; ε r = 35.485; ρ = 1000 kg/m 3 Ambient Temperature：23.5 °C ; Liquid Temperature：23.2 °C DASY5 Configuration: - Probe: EX3DV4 - SN7537; ConvF(4.8, 4.8, 4.8) @ 5600 MHz; Calibrated: 2021/04/26 - Sensor-Surface: 1.4mm (Mechanical Surface Detection) - Electronics: DAE4 Sn1585; Calibrated: 2021/04/15 - Phantom: Twin-SAM V8.0_1988; Type: QD 000 P41 AA; - Measurement SW: DASY52, Version 52.10 (4); SEMCAD X Version 14.6.14 (7483) Pin=50mW/Area Scan (91x91x1): Interpolated grid: dx=1.000 mm, dy=1.000 mm Maximum value of SAR (interpolated) = 10.3 W/kg Pin=50mW/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=4mm, dy=4mm, dz=1.4mm Reference Value = 49.10 V/m; Power Drift = -0.03 dB Peak SAR (extrapolated) = 18.0 W/kg SAR(1 g) = 4.25 W/kg; SAR(10 g) = 1.26 W/kg (SAR corrected for target medium) Maximum value of SAR (measured) = 10.9 W/kg Report No. : SFBDTL-WTW-P22020360 Plots of System Verification Test Laboratory: Bureau Veritas ADT SAR/HAC Testing Lab Date: 2022/03/22 S04 System Check_H5750_220322 DUT: Dipole 5 GHz; Type: D5GHzV2; SN: 1019 Communication System: UID 0, CW; Frequency: 5750 MHz;Duty Cycle: 1:1 Medium: H34T60N1_0322 Medium parameters used: f = 5750 MHz; σ = 5.354 S/m; ε r = 35.468; ρ = 1000 kg/m 3 Ambient Temperature：23.5 °C ; Liquid Temperature：23.2 °C DASY5 Configuration: - Probe: EX3DV4 - SN7537; ConvF(4.95, 4.95, 4.95) @ 5750 MHz; Calibrated: 2021/04/26 - Sensor-Surface: 1.4mm (Mechanical Surface Detection) - Electronics: DAE4 Sn1585; Calibrated: 2021/04/15 - Phantom: Twin-SAM V8.0_1988; Type: QD 000 P41 AA; - Measurement SW: DASY52, Version 52.10 (4); SEMCAD X Version 14.6.14 (7483) Pin=50mW/Area Scan (91x91x1): Interpolated grid: dx=1.000 mm, dy=1.000 mm Maximum value of SAR (interpolated) = 9.03 W/kg Pin=50mW/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=4mm, dy=4mm, dz=1.4mm Reference Value = 46.18 V/m; Power Drift = -0.05 dB Peak SAR (extrapolated) = 17.1 W/kg SAR(1 g) = 3.81 W/kg; SAR(10 g) = 1.13 W/kg (SAR corrected for target medium) Maximum value of SAR (measured) = 9.95 W/kg Report No. : SFBDTL-WTW-P22020360 Plots of System Verification Test Laboratory: Bureau Veritas ADT SAR/HAC Testing Lab Date: 2022/03/23 S05 System Check_H2450_220323 DUT: Dipole 2450 MHz; Type: D2450V2; SN: 737 Communication System: UID 0, CW; Frequency: 2450 MHz;Duty Cycle: 1:1 Medium: H19T27N1_0323 Medium parameters used: f = 2450 MHz; σ = 1.832 S/m; ε r = 39.967; ρ = 1000 kg/m 3 Ambient Temperature：23.4 °C ; Liquid Temperature：23.1 °C DASY5 Configuration: - Probe: EX3DV4 - SN7537; ConvF(7.61, 7.61, 7.61) @ 2450 MHz; Calibrated: 2021/04/26 - Sensor-Surface: 1.4mm (Mechanical Surface Detection) - Electronics: DAE4 Sn1585; Calibrated: 2021/04/15 - Phantom: Twin-SAM V8.0_1988; Type: QD 000 P41 AA; - Measurement SW: DASY52, Version 52.10 (4); SEMCAD X Version 14.6.14 (7483) Pin=50mW/Area Scan (81x81x1): Interpolated grid: dx=1.200 mm, dy=1.200 mm Maximum value of SAR (interpolated) = 4.06 W/kg Pin=50mW/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = 48.87 V/m; Power Drift = -0.04 dB Peak SAR (extrapolated) = 5.01 W/kg SAR(1 g) = 2.41 W/kg; SAR(10 g) = 1.13 W/kg (SAR c…

Text truncated - open the document above for the full version.

This report is governed by, and incorporates by reference, the Conditions of Testing as posted at the date of issuance of this report at http://www.bureauveritas.com/home/about-us/our- business/cps/about-us/terms-conditions/ and is intended for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. Measurement uncertainty is only provided upon request for accredited tests. Statements of conformity are based on simple acceptance criteria without taking measurement uncertainty into account, unless otherwise requested in writing. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence or if you require measurement uncertainty; provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Report No.: ORBDTL-WTW-P22100762-1 R3 Page: 1 of 10 Report Format Version 3.0.2 Cancels and replaces report no.: ORBDTL-WTW-P22100762-1 R2 , Dated: November.23, 2022 3D Antenna Measurement Summary Report REPORT NO.: ORBDTL-WTW-P22100762-1 R3 MODEL NAME: 84623918 ANTENNA TYPE: Dipole Antenna TESTED DATE: 2022.10.24 ISSUED: 2022.11.28 MANUFACTURER: TE Connectivity ADDRESS : 3F, No. 45, Dongsing RD, Taipei, Taiwan, 11070 ISSUED BY: Bureau Veritas Consumer Products Service(Hong Kong) Limited, Taoyuan Branch Mobile Communication Laboratory ADDRESS: No.19, Hwa Ya 2nd Rd., Kwei shan Dist., Taoyuan City, Taiwan (R.O.C) This report should not be used by the client to claim product certification, approval, or endorsement by TAF, CTIA or any government agencies. Report No.: ORBDTL-WTW-P22100762-1 R3 Page: 2 of 10 Report Format Version 3.0.2 Cancels and replaces report no.: ORBDTL-WTW-P22100762-1 R2, Dated: November.23, 2022 RELEASE CONTROL RECORD REPORT NO. REASON FOR CHANGE DATE ISSUED ORBDTL-WTW-P22100762-1 Original release 2022.11.16 ORBDTL-WTW-P22100762-1 R1 Update test date, Tester, Preparer, Approver 2022.11.17 ORBDTL-WTW-P22100762-1 R2 Remove EUT photos, add APPENDIX report 2022.11.23 ORBDTL-WTW-P22100762-1 R3 Update patterns, add antenna size in Appendix 2022.11.28 TABLE OF CONTENTS GENERAL INFORMATION ................................................................................................................................. 3 1. Test Methods ............................................................................................................................................... 4 2. Description of the anechoic chamber: ........................................................................................................ 4 3. Test Equipment List ..................................................................................................................................... 5 4. Measurement Uncertainty .......................................................................................................................... 5 5. Antenna Radiation Performance ................................................................................................................ 6 6. 3D Antenna Patterns .................................................................................................................................. 7 6.1. 84623918 ................................................................................................................................................... 7 Report No.: ORBDTL-WTW-P22100762-1 R3 Page: 3 of 10 Report Format Version 3.0.2 Cancels and replaces report no.: ORBDTL-WTW-P22100762-1 R2, Dated: November.23, 2022 GENERAL INFORMATION MANUFACTURER: TE Connectivity MODEL NAME: 84623918 MEASUREMENT STATNDARD ANSI/IEEE 149 1979. TEST BY: , DATE : 2022.11.28 Oscar Chiu / Engineer PREPARED BY : , DATE : 2022.11.28 Johnny Liu / Supervisor APPROVED BY : , DATE : 2022.11.28 Ken Chan / Manager Report No.: ORBDTL-WTW-P22100762-1 R3 Page: 4 of 10 Report Format Version 3.0.2 Cancels and replaces report no.: ORBDTL-WTW-P22100762-1 R2, Dated: November.23, 2022 1. Test Methods The Antenna Gain Test is performed according to The ANSI/IEEE Std 149 12.3.1 Antenna Gain (Small size (< 42cm) Linear Polarization Antennas), using a two-axis support device and one fixed measurement antenna. The EUT is positioned along the required MAPS centerline fixture holder. The EUT is then stepped between 0 and 180 degrees along the theta axis in 15-degree increments. At each theta position, the phi axis is stepped from 0-360 degrees in 15-degree increments. Data is recorded using the Network analyzer for both theta and phi polarizations at each position. Depending on the protocol, an appropriate filter is used in the EMQuest software to process the data. Upon completion of the test, test results (angular dependent EIRP) is calculated at each measurement point and the required value is automatically calculated. This test procedure is repeated for frequency and configuration as required. 2. Description of the anechoic chamber: Length: 7.32 m Width: 3.66 m Height: 3.51 m Network Analyzer Measurement Antenna EUT Phi axis Theta axis H V Report No.: ORBDTL-WTW-P22100762-1 R3 Page: 5 of 10 Report Format Version 3.0.2 Cancels and replaces report no.: ORBDTL-WTW-P22100762-1 R2, Dated: November.23, 2022 3. Test Eq…

Text truncated - open the document above for the full version.

Report No.: RFBDTL-WTW-P21060470-5 R1 Page No. 1 / 32 Report Format Version: 6.1.1 Cancels and replaces the report no. : RFBDTL-WTW-P21060470-5 dated on May 18, 2022 FCC Test Report (Co-Located) Report No.: RFBDTL-WTW-P21060470-5 R1 FCC ID: VUI-CFWM Test Model: 84911790C Received Date: Feb. 15, 2022 Test Date: Mar. 22, 2022 Issued Date: Nov. 22, 2022 Applicant: PEGATRON CORPORATION Address: 5F, NO. 76, LIGONG ST., BEITOU DISTRICT, TAIPEI CITY 112, TAIWAN Issued By: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch Lin Kou Laboratories Lab Address: No. 47-2, 14th Ling, Chia Pau Vil., Lin Kou Dist., New Taipei City, Taiwan Test Location: No. 19, Hwa Ya 2nd Rd., Wen Hwa Vil., Kwei Shan Dist., Taoyuan City 33383, TAIWAN FCC Registration / Designation Number: 788550 / TW0003 This report is governed by, and incorporates by reference, the Conditions of Testing as posted at the date of issuance of this report at http://www.bureauveritas.com/home/about-us/our-business/cps/about-us/terms-conditions/ and is intended for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. Measurement uncertainty is only provided upon request for accredited tests. Statements of conformity are based on simple acceptance criteria without taking measurement uncertainty into account, unless otherwise requested in writing. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence or if you require measurement uncertainty; provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Report No.: RFBDTL-WTW-P21060470-5 R1 Page No. 2 / 32 Report Format Version: 6.1.1 Cancels and replaces the report no. : RFBDTL-WTW-P21060470-5 dated on May 18, 2022 Table of Contents Release Control Record .................................................................................................................................. 3 1 Certificate of Conformity ...................................................................................................................... 4 2 Summary of Test Results ..................................................................................................................... 5 2.1 Measurement Uncertainty ................................................................................................................... 5 2.2 Modification Record ............................................................................................................................ 5 3 General Information .............................................................................................................................. 6 3.1 General Description of EUT ................................................................................................................ 6 3.2 Description of Test Modes ................................................................................................................. 10 3.2.1 Test Mode Applicability and Tested Channel Detail ........................................................................... 13 3.3 Description of Support Units ............................................................................................................. 15 3.3.1 Configuration of System under Test .................................................................................................. 15 3.4 General Description of Applied Standards and References .............................................................. 16 4 Test Types and Results ...................................................................................................................... 17 4.1 Radiated Emission and Bandedge Measurement ............................................................................. 17 4.1.1 Limits of Radiated Emission and Bandedge Measurement .............................................................. 17 4.1.2 Test Instruments ................................................................................................................................ 18 4.1.3 Test Procedures ................................................................................................................................. 19 4.1.4 Deviation from Test Standard ............................................................................................................ 20 4.1.5 Test Setup .......................................................................................................................................... 21 4.1.6 EUT Operating Conditions ................................................................................................................. 22 4.1.7 Test Results ....................................................................................................................................... 23 4.2 Conducted Out of Band Emission Measurement .............................................................................. 29 4.2.1 Limits of Conducted Out of Band Emission Measurement ................................................................ 29 4.2.2 Test Setup ........................................................................…

Text truncated - open the document above for the full version.

Report No.: RFBDTL-WTW-P21060470-4 R1 Page No. 1 / 247 Report Format Version: 6.1.2 Cancels and replaces the report No.: RFBDTL-WTW-P21060470-4 dated May 19, 2022 DFS Test Report Report No.: RFBDTL-WTW-P21060470-4 R1 FCC ID: VUI-CFWM Test Model: 84911790C Received Date: Feb. 15, 2022 Test Date: Apr. 11 ~ Apr. 21, 2022 Issued Date: Nov. 21, 2022 Applicant: PEGATRON CORPORATION Address: 5F, NO. 76, LIGONG ST., BEITOU DISTRICT, TAIPEI CITY 112, TAIWAN Issued By: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch Lin Kou Laboratories Lab Address: No. 47-2, 14th Ling, Chia Pau Vil., Lin Kou Dist., New Taipei City, Taiwan Test Location: No. 19, Hwa Ya 2nd Rd., Wen Hwa Vil., Kwei Shan Dist., Taoyuan City 33383, TAIWAN FCC Registration / Designation Number: 788550 / TW0003 This report is governed by, and incorporates by reference, the Conditions of Testing as posted at the date of issuance of this report at http://www.bureauveritas.com/home/about-us/our-business/cps/about-us/terms-conditions/ and is intended for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the…

Text truncated - open the document above for the full version.