VUIVPNFCNFC

VP-NFC 1. Introduction PN65OEV1 combines in a single package a Near Field Communication (NFC) controller . It is optimized for low power consumption with fully host controllable power states. 2. Features Host Interface: UART UART Baud Rates: 9600、28800、115200、230400、460800 Transmission modes: ISO/IEC 14443 A、ISO/IEC 14443 B、MIFARE、Sony FeliCa Operating ambient Temperature: -25 。 C ~+85 。 C Input Voltage: +1.8V RF Clock: 13.56M Hz Oscillator: 27.12M Hz PCB:4 Layer Weight: Approx. 3g 3. NFC antenna outline 4. Installing the device drivers To install the device driver in your computer: Step1. Run NXP_NFC_Drover_Pakcage Step2. Choose “Next” Step3. Choose “Next” Step4. Choose “Install” Step5. Choose “Finsh” Install success 5. NFC use cases Reader mode Peer-To-Peer 6. Antenna Detecting Range 7. Federal Communication Commission Interference Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. This device is intended only for OEM integrators under the following conditions: 1) The antenna must be installed such that 20 cm is maintained between the antenna and users, and 2) The transmitter module may not be co-located with any other transmitter or antenna. 3) Module approval valid only when the module is installed in the tested host or same series host with similar size and RF characteristics. As long as 3 conditions above are met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed IMPORTANT NOTE: In the event that these conditions can not be met (for example certain laptop configurations or co-location with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID can not be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC authorization. End Product Labeling This transmitter module is authorized only for use in device where the antenna may be installed such that 20 cm may be maintained between the antenna and users. The final end product must be labeled in a visible area with the following: “Contains FCC ID:VUIVPNFC”. The grantee's FCC ID can be used only when all FCC compliance requirements are met. Manual Information To the End User The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the user’s manual of the end product which integrates this module. The end user manual shall include all required regulatory information/warning as show in this manual. 8. Industry Canada statement: This device complies with RSS-210 of the Industry Canada Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Ce dispositif est conforme à la norme CNR-210 d'Industrie Canada applicable aux appareils radio exempts de licence. Son fonctionnement est sujet aux deux conditions suivantes: (1) le dispositif ne doit pas produire de brouillage préjudiciable, et (2) ce dispositif doit accepter tout brouillage reçu, y compris un brouillage susceptible de provoquer un fonctionnement indésirable. Radiation Exposure Statement: This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. Déclaration d'exposition aux radiations: Cet équipement est conforme aux limites d'exposition aux rayonnements IC établies pour un environnement non contrôlé. Cet équipement doit être installé et utilisé avec un minimum de 20 cm de distance entre la source de rayonnement et votre corps. This device is intended only for OEM integrators under the following conditions: (For module device use) 1) The antenna must be installed such that 20 cm is maintained between the antenna and users, and 2) The transmitter module may not be co-located with any other transmitter or…

Text truncated - open the document above for the full version.

Page 1 CONSTRUCTION PHOTOS OF EUT EUT Page 2 PLATFORM Page 3 Page 4 Page 5 Page 6 Page 7 Page 8

DOC Location FCC ID Location

Page: 1 Page: 2 Page: 3 Page: 4 Page: 5 Page: 6 Page: 7 Page: 8 Page: 9

Report No.: RF120730D34 1 of 28 Report Format Version 5.0.0 FCC TEST REPORT REPORT NO.: RF120730D34 MODEL NO.: VP-NFC FCC ID: VUIVPNFC RECEIVED: Jul. 30, 2012 TESTED: Aug. 13 ~ 20, 2012 ISSUED: Aug. 28, 2012 APPLICANT: PEGATRON CORPORATION ADDRESS: 5F, No. 76, Ligong ST., Beitou District, Taipei City, Taiwan (R.O.C.) ISSUED BY: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch LAB ADDRESS: No. 47, 14th Ling, Chia Pau Vil., Lin Kou Dist., New Taipei City, Taiwan ( R.O.C. ) This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the compliance or non-compliance to the specification. This report should not be used by the client to claim product certification, approval, or endorsement by TAF or any government agencies. Report No.: RF120730D34 2 of 28 Report Format Version 5.0.0 Table of Contents RELEASE CONTROL RECORD................................................................................. 3 1. CERTIFICATION .............................................................................................. 4 2. SUMMARY OF TEST RESULTS ...................................................................... 5 2.1 MEASUREMENT UNCERTAINTY ................................................................... 5 3. GENERAL INFORMATION .............................................................................. 6 3.1 GENERAL DESCRIPTION OF EUT ................................................................. 6 3.2 DESCRIPTION OF TEST MODES ................................................................... 8 3.2.1 TEST MODE APPLICABILITY AND TESTED CHANNEL DETAIL ................... 8 3.3 DESCRIPTION OF SUPPORT UNITS ............................................................. 9 3.3.1 CONFIGURATION OF SYSTEM UNDER TEST ............................................ 10 3.4 GENERAL DESCRIPTION OF APPLIED STANDARDS ................................ 10 4. TEST TYPES AND RESULTS .........................................................................11 4.1 RADIATED EMISSION MEASUREMENT .......................................................11 4.1.1 LIMITS OF RADIATED EMISSION MEASUREMENT .....................................11 4.1.2 TEST INSTRUMENTS ................................................................................... 12 4.1.3 TEST PROCEDURES .................................................................................... 13 4.1.4 DEVIATION FROM TEST STANDARD .......................................................... 13 4.1.5 TEST SETUP ................................................................................................. 14 4.1.6 EUT OPERATING CONDITIONS ................................................................... 14 4.1.7 TEST RESULTS ............................................................................................. 15 4.2 CONDUCTED EMISSION MEASUREMENT ................................................. 19 4.2.1 LIMITS OF CONDUCTED EMISSION MEASUREMENT ............................... 19 4.2.2 TEST INSTRUMENTS ................................................................................... 19 4.2.3 TEST PROCEDURES .................................................................................... 20 4.2.4 DEVIATION FROM TEST STANDARD .......................................................... 20 4.2.5 TEST SETUP ................................................................................................. 20 4.2.6 EUT OPERATING CONDITIONS ................................................................... 20 4.2.7 TEST RESULTS ............................................................................................. 21 4.3 FREQUENCY STABILITY .............................................................................. 23 4.3.1 LIMITS OF FREQUENCY STABILITY MEASUREMENT ............................... 23 4.3.2 TEST INSTRUMENTS ................................................................................... 23 4.3.3 TEST PROCEDURE ...................................................................................... 23 4.3.4 DEVIATION FROM TEST STANDARD .......................................................... 24 4.3.5 TEST SETUP ................................................................................................. 24 4.3.6 EUT OPERATING CONDITION ..................................................................... 24 4.3.7 TEST RESULTS ............................................................................................. 25 5. PHOTOGRAPHS OF THE TEST CONFIGURATION ..................................... 26 6. INFORMATION ON THE TESTING LABORATORIES ................................... 27 7. APPENDIX A - MODIFICATIONS RECORDERS FOR ENGINEERING CHANGES TO THE EUT BY THE LAB ......................................................... 28 Report No.: RF120730D34 3 of 28 Report Forma…

Text truncated - open the document above for the full version.

Report No.: RF120430D34 1 of 2 Report Format Version 5.0.0 PHOTOGRAPHS OF THE TEST CONFIGURATION CONDUCTED EMISSION TEST Report No.: RF120430D34 2 of 2 Report Format Version 5.0.0 RADIATED EMISSION TEST