VW4A09-0491ATAVRRZ600

AVR600: RZ600 HW Manual Features • Contains the full selection of AT86RF family radio transceivers. • Covers the 2.4GHz ISM band and 700, 800 and 900 MHz frequency bands. • In total 3 pair of radio transceivers are available – one pair per radio transceiver. • Two AT32UC3A3256 based USB host boards are included - Based on Atmel ® AVR ® UC3 core - 80 Dhrystone MIPS and Draws Only 40 mA at 66 MHz - Low, full and high speed USB compliant - Ideal for PC to RF gateways, packet sniffers and network commissioning tools • On board ID chip for easy IEEE MAC address • Stub antennas for all frequency bands 1 Introduction The RZ600 kit is an evaluation kit for the Atmel AT86RF family of radio frequency devices. The family contains the two 2.4 GHz device AT86RF230 and AT86RF231. These are highly acclaimed networking devices within low power personal area networks. In addition to this the world’s first IEEE 802.15.4 enabled sub gigahertz radio is provided – the AT86RF212. With the kit you also receive two AVR UC3 based host nodes that can be used to evaluate a point to point network connection. That being said; the RZ600 radio boards sport an Atmel standardized 10-pin connector that will enable the RF boards to be connected to any AVR microcontroller. A wide range of the standard Atmel AVR design tools have the host end of the standardized 10-pin connector – so as a customer you will be able to evaluate Atmel radio transceivers in virtually any application segment. The RZ600 kit enables RF4CE, IEEE 802.15.4, ZigBee ® and 6lowPAN network technologies to run on the full Atmel portfolio of low power AVR microcontrollers. Figure 1-1. RZ600 HW Overview Microcontrollers Application Note Rev. 8293-AVR-02/10 2 AVR600 8293-AVR-02/10 2 Related Items AVR32 Studio (Atmel’s free IDE) http://www.atmel.com/dyn/products/tools_card.asp?tool_id=4116 GNU Toolchain (Atmel’s free Compiler and Utilities) http://www.atmel.com/dyn/products/tools_card.asp?tool_id=4118 JTAGICE mkII (On-chip programming and debugging tool) http://www.atmel.com/dyn/products/tools_card.asp?tool_id=3353 AVR ONE! (On-chip programming and debugging tool) http://www.atmel.com/dyn/products/tools_card.asp?tool_id=4279 3 Overview This section gives an overview of the RZ600 kit from a system perspective as well as what the kit contains and its minimum requirements. A set of condensed instructions are then given on how to get the evaluation application for the kit up and running in the shortest time possible. Figure 3-1 shows how the two processor boards paired with the radio frequency boards also available in the kit can form a wireless peer to peer data connection over USB. The application that is pre programmed by Atmel on the AT32UC3A3256 is indeed such a USB to RF gateway. AVR600 3 8293-AVR-02/10 Figure 3-1 RZ600 used in conjuntion with PC RF Link RZ600 Processor Board RZ600 RF Board 3.1 Kit Contents The RZ600 kit contains the following pieces of hardware: • 2 pcs. AT86RF230 radio cards: miniature carrier board with the AT86RF230 radio transceiver mounted, SMA antenna connector, one wire ID chip and Atmel standard 10-pin connector. • 2 pcs. AT86RF231 radio cards: miniature carrier board with the AT86RF231 radio transceiver mounted, SMA antenna connector, one wire ID chip and Atmel standard 10-pin connector. • 2 pcs. AT86RF212 radio cards: miniature carrier board with the AT86RF212 radio transceiver mounted, SMA antenna connector, one wire ID chip and Atmel standard 10-pin connector. • 2 pcs. AVR UC3 based processor cards: usb dongle form factor board with AT32UC3A3256 processor mounted, LEDs, UART connection and host side Atmel standard 10-pin connector. • 2 pcs. 2.4GHz SMA stub antenna. These are shared between the AT86RF230 and AT86RF231 radio transceivers. 4 AVR600 8293-AVR-02/10 • 2 pcs. Sub gigahertz SMA stub antenna. Used with the AT86RF212 radio transceiver. • 2 pcs. Bag with wires and squid cable: The squid cable fits the radio frequency boards and will enable wiring to a hardware that does not contain the standard Atmel 10-pin accessory header. • 1 pcs. Technical Library CD 3.2 System Requirements Table 3-1 contains the minimum system requirements for the RZ600 kit when connected to a PC for application development on the AT32UC3A3256 microcontroller. Table 3-1. Minimum System Requirements Parameter Value Comment Hardware PC/CPU Intel ® Pentium III or better, 800 MHz PC/RAM 128 MBytes PC/Video 1024x768, SVGA PC/ Hard disk free space 200 Mbytes On-Chip Debugger and programmer AVR JTAGICE mkII or AVRONE! The AVR JTAGICE mkII or AVRONE! is needed if the user wishes to debug and do custom application development. Software Operating System Windows ® 2000/XP/Vista IDE AVR32 Studio or IAR Embedded Workbench AVR32 Studio with compiler utilities is required for reprogramming the processor board and for application development. 3.3 Quick Start Guide To following sequence is suggested when testing the evaluation application the RZ600 kit: 1. Unpack the kit and verify contents 2. Identify the processor boards and select two radio frequency boards with the same radio transceiver mounted. It is suggested to do this even though there are two different radio transceivers for the 2.4GHz band that are fully compatible with each other: AT86RF230 vs. AT86RF231. 3. Mount a radio frequency board to each of the processor boards 4. Insert the assembly into a free USB port on the computer. 5. Let the devices enumerate – they should become available as two CDC virtual COM ports. 6. Open two terminal windows and start typing. Verify that the text in the two terminals is the same. AVR600 5 8293-AVR-02/10 4 Hardware Description This chapter walks through the different pieces of hardware that you will find in the RZ600 kit in greater detail. 4.1 Radio Frequency Board A total of six radio frequency boards included in the kit, two boards per radio transceiver: • AT86RF230: First generation 2.4GHz ISM band radio transceiver from Atmel. • AT86RF231: Second generation 2.4GHz …

Text truncated - open the document above for the full version.

Radio chip AT86RF212 MCU: AT32UC3A3256, USB and RF Stacks 12MHz Xtal USB interface 10 pin con 2-way sync Serial comm 16MHz Xtal MCU oscillator Antenna IJ28-SS 32kHz Xtal Realtime Clock oscillator SMA connector USB card A09-0831 RF card A09-0491 Block Diagram, ATAVRRZ600, A09-0491

FCC Part 15 & RSS-210 Project no.: 140235 Page 1 of 2 Nemko AS, NO-2007 Kjeller INTERNAL PHOTOS A09-0491 Rear view Top view FCC Part 15 & RSS-210 Project no.: 140235 Page 2 of 2 Nemko AS, NO-2007 Kjeller Whip antenna

FCC Part 15 & RSS-210 Project no.: 140235 Page 1 of 2 Nemko AS, NO-2007 Kjeller INTERNAL PHOTOS A09-0491 Rear view Top view FCC Part 15 & RSS-210 Project no.: 140235 Page 2 of 2 Nemko AS, NO-2007 Kjeller Whip antenna

AT86RF212 Low Power 700/800/900 MHz Transceiver for IEEE 802.15.4, P802.15.4c Draft Amendment, Zigbee, 6LoWPAN, and ISM Applications PRELIMINARY 8168B-MCU Wireless-02/09 Features • Fully Integrated 700/800/900 MHz-Band Transceiver - Chinese WPAN Band from 779 to 787 MHz - European SRD Band from 863 to 870 MHz - North American ISM Band from 902 to 928 MHz • Direct Sequence Spread Spectrum with Different Modulation Schemes and Data Rates - BPSK with 20 and 40 kbit/s, compliant to IEEE 802.15.4-2006 - O-QPSK with 100 and 250 kbit/s, compliant to IEEE 802.15.4-2006 - O-QPSK with 250 kbit/s, compliant to IEEE P802.15.4c - O-QPSK with 200, 400, 500, and 1000 kbit/s PSDU Data Rate • Flexible Combination of Frequency Bands and Data Rates • Industry Leading Link Budget - Receiver Sensitivity up to -110 dBm - Programmable TX Output Power up to +10 dBm • Low Power Supply Voltage from 1.8 V to 3.6 V - Internal Voltage Regulators and Battery Monitor • Low Current Consumption - SLEEP = 0.2 μA - TRX_OFF = 0.4 mA - RX_ON = 9.0 mA - BUSY_TX = 18 mA at P TX = 5 dBm • Digital Interface - Registers, Frame Buffer, and AES Accessible through SPI - Clock Output with Configurable Rate • Radio Transceiver Features - Adjustable Receiver Sensitivity - Integrated TX/RX Switch, LNA, and PLL Loop Filter - Fast Settling PLL Supporting Frequency Hopping - Automatic VCO and Filter Calibration - Integrated 16 MHz Crystal Oscillator - 128 byte FIFO for Transmit/Receive • IEEE 802.15.4-2006 Hardware Support - FCS Computation and Check - Clear Channel Assessment - Received Signal Strength Indicator, Energy Detection, and Link Quality Indication • MAC Hardware Accelerator - Automatic Acknowledgement and Retransmission - CSMA-CA and LBT - Automatic Frame Filtering • AES 128 bit Hardware Accelerator (ECB and CBC modes) • Extended Feature Set Hardware Support - True Random Number Generation for Security Applications - TX/RX Indication (External RF Front End Control) • Optimized for Low BoM Cost and Ease of Production - Low External Component Count: Antenna, Reference Crystal, and Bypass Capacitors - Excellent ESD Robustness • Industrial Temperature Range from -40°C to +85°C • 32-pin Low-profile Lead-free Plastic QFN Package, 5.0 x 5.0 x 0.9 mm 3 • Compliant to IEEE 802.15.4-2003, IEEE 802.15.4-2006, IEEE P802.15.4c, ETSI EN 300 220-1, and FCC 47 CFR Section 15.247 2 8168B-MCU Wireless-02/09 AT86RF212 1 Overview The AT86RF212 is a low-power, low-voltage 700/800/900 MHz transceiver specially designed for the IEEE Standard 802.15.4, ZigBee, 6LoWPAN, and high data rate ISM applications. For the sub-1 GHz bands, it supports low data rates (20 and 40 kbit/s) of the IEEE Standard 802.15.4-2003 [2] and provides optional data rates (100 and 250 kbit/s) using O-QPSK, according to the IEEE Standard 802.15.4-2006 [1] and the respective IEEE P802.15.4c Draft Amendment [3]. Furthermore, proprietary High Data Rate Modes up to 1000 kbit/s can be employed. The AT86RF212 is a true SPI-to-antenna solution. RF-critical components except the antenna, crystal, and de-coupling capacitors are integrated on-chip. MAC and AES hardware accelerators improve overall system power efficiency and timing. 1.1 General Circuit Description The AT86RF212 single-chip RF transceiver provides a complete radio interface between the antenna and the microcontroller. It comprises the analog radio part, digital modulation and demodulation including time and frequency synchronization, as well as data buffering. The number of external components is minimized so that only the antenna, a filter (at high output power levels), the crystal, and four bypass capacitors are required. The bidirectional differential antenna pins are used in common for RX and TX, i.e. no external antenna switch is needed. Control of an external power amplifier is supported by two digital control signals (differential operation). The transceiver block diagram is shown in Figure 1-1. The re ceiver path is based on a low-IF architecture. After channel filtering and down- conversion the low-IF signal is sampled and applied to the digital signal processing part. Communication between transmitter and receiver is based on direct sequence spread spectrum with different modulation schemes and spreading codes. The AT86RF212 supports the IEEE 802.15.4-2006 standard mandatory BPSK modulation and optional O-QPSK modulation in the 868.3 MHz and 915 MHz bands. In addition it supports the O-QPSK modulation defined in IEEE P802.15.4c for the Chinese 780 MHz band. For applications not necessarily targeting IEEE compliant networks the radio transceiver supports proprietary High Data Rate Modes based on O-QPSK. A single 128 byte TRX buffer stores receive or transmit data. The AT86RF212 features hardware supported 128 bit security operation. The standalone AES encryption/decryption engine can be accessed in parallel to all PHY operational modes. Configuration of the AT86RF212, reading, and writing of data memory as well as the AES hardware engine are controlled by the SPI interface and additional control signals. On-chip low-dropout voltage regulators provide the analog and digital 1.8 V power supply. Control registers retain their settings in SLEEP mode when the regulators are turned off. The RX and TX signal processing paths are highly integrated and optimized for low power consumption. 3 8168B-MCU Wireless-02/09 AT86RF212 Figure 1-1. AT86RF212 Block Diagram XTAL1XTAL2 Voltage Regulator LNA Frequency Synthesis PPFBPFADC AGC RX BBP TX Power TRX Buffer Configuration Registers SPI (Slave) TX BBP IRQ CLKM DIG1 /RST SLP_TR /SEL MISO MOSI SCLK RFN DIG2 FTN, BATMON XOSC Analog DomainDigital Domain Mixer MixerLPFDAC PA RFP AES Control Logic DIG3/4 4 8168B-MCU Wireless-02/09 AT86RF212 2 Pin Configuration 2.1 Pin-out Diagram Figure 2-1. AT86RF212 Pin-out Diagram 32 24 23 22 21 20 19 18 17 1 2 3 4 5 6 7 8 AT86RF212 CLKM DVSS DIG3 DIG4 AVSS AVSS RFP RFN DVSS /RST DIG1DIG2 SLP_TR DVSS DVDDDVDD DEVDD DVSS SCLK MISO DVSS MOSI /SEL IRQ…

Text truncated - open the document above for the full version.

Tekfun Co., Ltd. ________________________________________________________________________________________________________________________________________________________________________________________________________________________________ ___ TEKFUN CO., Ltd. E-mail: [email protected] URL: www.tekfun.com.tw 4F., No.32, Kunming St., Jhongli City, Taoyuan Hsien 32089, Taiwan Tel : 886-3-4280826 Fax:886-3-4280010 SPECIFICATION FOR APPROVAL CUSTOMER DESCRIPTION 860-930MHz Rubber Stubby Antenna with SMA Male Straight PART NO. IJ28-SS DATE DESIGNER DIRECTOR Approved by Customer/date: Tekfun Co., Ltd. Page1 of 6 ________________________________________________________________________________________________________________________________________________________________________________________________________________________________ ___ TEKFUN CO., Ltd. E-mail: [email protected] URL: www.tekfun.com.tw 4F., No.32, Kunming St., Jhongli City, Taoyuan Hsien 32089, Taiwan Tel : 886-3-4280826 Fax:886-3-4280010 ANTENNA SPECIFICATIONS FOR APPROVAL 1. GENERAL DESCRIPION 1.1 Type No. : IJ28-SS 1.2 Customer P/N : 2. DESCRIPTION & APPLICATION 860-930MHz Rubber Stubby Antenna with SMA Male Straight 3. ELECTRICAL CHARACTERISTICS 3.1 Frequency Range : 860-930MHz 3.2 Electric Wave : 1/4, Monopole Antenna 3.3 V.S.W.R : < 2 3.4 Impedance : 50 Ω, Nominal 3.5 Gain : < 0dBi 3.6 Connector : SMA Male Straight 4. PACKING STYLE Poly Bag Tekfun Co., Ltd. ________________________________________________________________________________________________________________________________________________________________________________________________________________________________ ___ TEKFUN CO., Ltd. E-mail: [email protected] URL: www.tekfun.com.tw 4F., No.32, Kunming St., Jhongli City, Taoyuan Hsien 32089, Taiwan Tel : 886-3-4280826 Fax:886-3-4280010 5. APPEARANCE DRAWING SMA Tekfun Co., Ltd. ________________________________________________________________________________________________________________________________________________________________________________________________________________________________ ___ TEKFUN CO., Ltd. E-mail: [email protected] URL: www.tekfun.com.tw 4F., No.32, Kunming St., Jhongli City, Taoyuan Hsien 32089, Taiwan Tel : 886-3-4280826 Fax:886-3-4280010 6. TESTING VSWR & Return Loss Tekfun Co., Ltd. ________________________________________________________________________________________________________________________________________________________________________________________________________________________________ ___ TEKFUN CO., Ltd. E-mail: [email protected] URL: www.tekfun.com.tw 4F., No.32, Kunming St., Jhongli City, Taoyuan Hsien 32089, Taiwan Tel : 886-3-4280826 Fax:886-3-4280010 7. PHOTO I28-SS: The right one in the picture

Qty Designator Description MPN Manufacturer ShortName 1 C105 Ceramic capacitor, SMD 0402, NP0, 50V, +/-0.25pF 1.5p 2 C103, C104 Ceramic capacitor, SMD 0402, NP0, 50V, +/-5% 12p 1 R102 Ceramic capacitor, SMD 0402, NP0, 50V, +/-10% 100p 1 C111 Ceramic capacitor, SMD 0402, X7R, 25V, +/-10% 10n 1 C110 Ceramic capacitor, SMD 0402, X7R, 16V, +/-10% C0402C104K4RACTU Kemet 100n 9 C101, C102, C106, C107, C108, C109, C112, C113, C114 Ceramic capacitor, SMD 0402, X5R, 6.3V, +/-10% C0402C105K9PAC Kemet 1u 3 R104, R105, R109 Thick film resistor, SMD 0402, 1/16W, 1% 0R 1 R106 Thick film resistor, SMD 0402, 1/16W, 1% 470R 1 R111 Thick film resistor, SMD 0402, 1/16W, 1% 2.2k 1 L101 SMD RF inductor 0805. Z=1000Ohm (@100MHz), Max R(dc)=0.45Ohm, Max current=200mA BLM21AG102SN1D Murata BLM21AG102SN1D 1 L102 867-915 MHZ FilterBalun, 2x1,25mm 0896FB15A0100E Johanson Technology 867-915 MHZ FilterBalun 1 U101 7/8/900 MHz ZigBee/802.15.4 tranceiver AT86RF212-ZU ATMEL AT86RF212-ZU 1 U103 1-wire Serial number chip DS2411R/T&R Maxim DS2411R 1 U102 LDO 3.3V 150mA SOT23-5 LP2985AIM5-3.3 National Semiconductor LP2985 3.3V 1 XC101 SMT Crystal Resonator, 16.000 MHz,10 ppm,12 pF, 2520(Q) SCQ18D48-16.000MHZ TR SUNTSU FREQUENCY CONTROL 16MHz 1 J101 Samtec SMH 2x5 Pin Socet Right-angle 2,54mm Pitch (Mirrored footprint) SMH-105-02-T-D-TR SAMTEC SMH-105-02-T-D-TR 1 PCB101 RZ600 RF board PCB NCAB RZ600 RF board PCB 1 J102 SMA PCB mounted connector LTI-SASF56GT Lighthorse Technologies inc. LTI-SASF56GT 1 Z102 Label for use on wireless PCBA that needs 64 bit MAC and FCC ID 505462 ACT Logimark AS Label PCBA with MAC64 and FCC ID 1 PCBA101 RZ600 RF board PCBA RZ600 RF board PCBA

1 1 2 2 3 3 4 4 5 5 6 6 7 7 8 8 DD CC BB AA A12-0171 A08-0671 Rev3.SchDoc 111/8/20101:00:05 PM RF Board Embedded Wireless Labs Sdn Bhd 702, Uptown 2, SS21/37 Damansara Uptown PJ, Sel, Malaysia PAGE:of TITLE: Document number:Revision:Rev 3 Date: Jeyaraman * * 12 34 56 78 910 SMH-105-02-T-D-TR J101 AVSS 1 AVSS 2 AVSS 3 RFP 4 RFN 5 AVSS 6 TST 7 RST 8 DVSS 9 DVSS 10 SLP_TR 11 DVSS 12 DVDD 13 DVDD 14 DEVDD 15 DVSS 16 CLKM 17 DVSS 18 SCLK 19 MISO 20 DVSS 21 MOSI 22 SEL 23 IRQ 24 XTAL1 25 XTAL2 26 AVSS 27 EVDD 28 AVDD 29 AVSS 30 AVSS 31 AVSS 32 AVSS 33 U101 AT86RF230-ZU UnBal 1 GND 2 BAL1 3 BAL2 4 GND 5 GND/NC 6 L102 2450FB15L0001 10K R104 1 2 3 CD75014 1X3 J104 1 24 3 SCQ18D48-16.000MHz TR XC101 I/O 1 VCC 2 GND 3 U103 DS2411-R RF_VCC 12pF C104 12pF C103 1uF C101 1uF C102 1uF C112 1uF C113 RF_VCC VCC 1uF C114 VCC 2.2K R111 VCC IRQ SEL MOSI MISO SCLK CLKM 1uF C106 100nF C110 RSTRST SLP_TR RST IRQ SEL MISO SLP_TR MOSI SCLK 12 CD075014 1X2 J103 RF_VCC TST ID LTI-SASF56GT RF 1 GND 2 GND 3 J102 0R / NM R108 0R R109 0R / NM R110 MISC MISC Private & Confidential BLM21AG102SN1D L1010R R105 470R R106 0R / NM R107 0R / NM R103 0R / NM R101 1.5pF C105 L102: For RF212: Use P/N 0896FB15A0100E, Johanson Technology U101: For RF212: Use P/N AT86RF212-ZU, Atmel For RF231: Use P/N AT86RF231-ZU, Atmel 1uF C107 1uF C108 1uF C109 R104: For RF212: Use 0R Value For RF231: Use 0R Value R102: For RF212: Use 100pF Capacitor 0R R102 PCB101 A08-0671 GND 2 GND 1 GND 3 GND 4 Z101 Z102 PCBA Label Place Label on the Bottom Side Place EMI Shield on Top Side IN 1 OUT 5 2 BYP 4 ON/OFF 3 GND LP2985AIM5-3.3/NOPB U102 10nF C111 TP112 TP104TP105 TP109 TP113 TP110 TP101 TP102 TP107TP111TP108TP106 RF_P RF_N A a i PCB Rule i PCB Rule i PCB Rule i PCB Rule TP114 MISC RST SLP_TR MISC CLKM TP115 0R / NM R112 R101, R103, R107, R112 Equip for RF230 Do not Equip for RF231 & RF212 TP116TP117TP118TP119TP120TP121TP122 SCLKMOSISLP _TR SEL MISOIRQ RST TP123 MISC Transciever Current Measurement: Mount J103 & Remove R105 PIC10101PIC10102 COC101 PIC10201PIC10202 COC102 PIC10301 PIC10302 COC103 PIC10401 PIC10402 COC104 PIC10501 PIC10502 COC105 PIC10601 PIC10602 COC106 PIC10701 PIC10702 COC107 PIC10801 PIC10802 COC108 PIC10901 PIC10902 COC109 PIC11001 PIC11002 COC110 PIC11101 PIC11102 COC111 PIC11201 PIC11202 COC112 PIC11301 PIC11302 COC113 PIC11401 PIC11402 COC114 PIJ10101PIJ10102 PIJ10103PIJ10104 PIJ10105PIJ10106 PIJ10107PIJ10108 PIJ10109PIJ101010 COJ101 PIJ10201 PIJ10202 PIJ10203 COJ102 PIJ10301PIJ10302 COJ103 PIJ10401 PIJ10402 PIJ10403 COJ104 PIL10101PIL10102 COL101 PIL10201 PIL10202 PIL10203 PIL10204 PIL10205PIL10206 COL102 COPCB101 PIR10101PIR10102 COR101 PIR10201PIR10202 COR102 PIR10301PIR10302 COR103 PIR10401 PIR10402 COR104 PIR10501PIR10502 COR105 PIR10601 PIR10602 COR106 PIR10701 PIR10702 COR107 PIR10801 PIR10802 COR108 PIR10901 PIR10902 COR109 PIR11001 PIR11002 COR110 PIR11101 PIR11102 COR111 PIR11201 PIR11202 COR112 PITP10101 COTP101 PITP10201 COTP102 PITP10401 COTP104 PITP10501 COTP105 PITP10601 COTP106 PITP10701 COTP107 PITP10801 COTP108 PITP10901 COTP109 PITP11001 COTP110 PITP11101 COTP111 PITP11201 COTP112 PITP11301 COTP113 PITP11401 COTP114 PITP11501 COTP115 PITP11601 COTP116 PITP11701 COTP117 PITP11801 COTP118 PITP11901 COTP119 PITP12001 COTP120 PITP12101 COTP121 PITP12201 COTP122 PITP12301 COTP123 PIU10101 PIU10102 PIU10103 PIU10104 PIU10105 PIU10106 PIU10107 PIU10108 PIU10109PIU101010PIU101011PIU101012PIU101013PIU101014PIU101015PIU101016 PIU101017 PIU101018 PIU101019 PIU101020 PIU101021 PIU101022 PIU101023 PIU101024 PIU101025PIU101026PIU101027PIU101028PIU101029PIU101030PIU101031PIU101032PIU101033 COU101 PIU10201 PIU10202 PIU10203PIU10204 PIU10205 COU102 PIU10301PIU10302 PIU10303 COU103 PIXC10101 PIXC10102 PIXC10103 PIXC10104 COXC101 PIZ10101PIZ10102PIZ10103PIZ10104 COZ101 COZ102 PIC10501 PIJ10401 PIR10601 PIR11001 NLCLKM PIC10101 PIC10201 PIC10302PIC10402 PIC10502 PIC10602PIC10702PIC10802PIC10902PIC11002 PIC11102 PIC11201PIC11301 PIC11401 PIJ10109 PIJ10202 PIJ10203 PIL10202PIL10205PIL10206 PIR10102 PIR10302 PIR10401 PIR10701 PIR11201 PITP11201 PITP11401 PIU10103 PIU10106 PIU101012PIU101016 PIU101018 PIU101021 PIU101027PIU101030PIU101031PIU101032PIU101033 PIU10202 PIU10303 PIZ10101PIZ10102PIZ10103PIZ10104 PIJ10402 PIR10901 PIR11101 PIU10301 NLID PIJ10103 PITP11701 PIU101024 NLIRQ PIJ10102 PIR10802PIR10902PIR11002 PITP12301 NLMISC PIJ10107 PITP12101 PIU101020 NLMISO PIJ10106 PITP12001 PIU101022 NLMOSI PIC10202 PITP10201 PIU101029 PIC10301 PIU101025 PIXC10101 PIC10401 PIU101026 PIXC10103 PIC10601 PIJ101010 PITP10701 PIU10201 PIU10203 PIC11101 PITP11101 PIU10204 PIC11202 PITP11301 PIU101013PIU101014 PIJ10201PIR10202 PIJ10301 PIL10101 PIR10502 PITP10601 PIL10201PIR10201 PIR10101 PITP10401 PIU10101 PIR10301 PITP10501 PIU10102 PIR10602 PITP11001 PIU101017 PIR10702 PITP10901 PIU10109 PIR11202 PITP11501 PIU101010 PIXC10102PIXC10104 PIJ10101 PITP11601 PIU10108 NLR\S\T\ PIL10203 PIU10105 NLRF0N PIL10204 PIU10104 NLRF0P PIC10102 PIC11302 PIL10102 PITP10101 PIU101015 PIU101028 PIJ10105 PITP11901 PIU101023 NLS\E\L\ PIJ10108 PITP12201 PIU101019 NLSCLK PIJ10104 PITP11801 PIU101011 NLSLP0TR PIJ10403 PIR10402 PIR10801 PIU10107 NLTST PIC10701PIC10801PIC10901PIC11001 PIC11402 PIJ10302 PIR10501 PIR11102 PITP10801 PIU10205 PIU10302

1 1 2 2 3 3 4 4 5 5 6 6 7 7 8 8 DD CC BB AA A12-0172 A08-0672 Rev3.SchDoc 111/8/201012:57:53 PM USB Adaptor Embedded Wireless Labs Sdn Bhd 702, Uptown 2, SS21/37 Damansara Uptown, PJ, Sel, Malaysia PAGE:of TITLE: Document number:Revision:Rev 3 Date: Jeyaraman * * USB_P USB_N PA0 G11 PA1 G12 PA2 D8 PA3 G10 PA4 F9 PA5 F10 PA6 F8 PA7 E10 PA8 C11 PA9 B12 PA10 C12 PA11 D10 PA12 E12 PA13 F11 PA14 J6 PA15 J7 PA16 F12 PA17 H7 PA18 K8 PA19 J8 PA20 J9 PA21 H9 PA22 H10 PA23 G8 PA24 G9 PA25 E9 PA26 D9 PA27 A4 PA28 A3 PA29 A6 PA30 C7 PC0/XIN32 K5 PC1/XOUT32 H6 PC2/XIN0 A7 PC3/XOUT0 B7 PC4/XIN1 A8 PC5/XOUT1 A9 PA31 B3 FSDM B10 FSDP C9 HSDM A11 HSDP A10 VBUS A12 VBIAS B9 RESET_N J12 TCK K12 TDO J11 TDI L12 TMS J10 VDDCORE E11 ONREG L8 VDDIN E8 GNDCORE C10 GNDPLL B11 VDDANA H11 GNDANA L11 VDDIO E2 GNDIO C3 VDDIO H2 GNDIO L2 VDDIO B5 GNDIO K3 VDDIO E5 GNDIO F6 GNDIO G6 VDDIO H5 VDDIO/VBOOST H8 GNDIO F7 VDDIO L5 GNDIO G7 GNDIO K10 VDDIO B8 PX0 G1 PX1 H1 PX2 J2 PX3 K1 PX4 J1 PX5 G2 PX6 F3 PX7 F2 PX8 D1 PX9 C1 PX10 B1 PX11 L1 PX12 D6 PX13 C6 PX14 M4 PX15 E6 PX16 C5 PX17 K6 PX18 L6 PX19 D5 PX20 L4 PX21 M5 PX22 M1 PX23 M6 PX24 M7 PX25 M8 PX26 L9 PX27 K9 PX28 L10 PX29 K11 PX30 M11 PX31 M10 PX32 M9 PX33 M12 PX34 J3 PX35 C2 PX36 D3 PX37 D2 PX38 E1 PX39 F1 PX40 A1 PX41 M2 PX42 M3 PX43 L7 PX44 K2 PX45 L3 PX46 K4 PX47 D4 PX48 F5 PX49 F4 PX50 G4 PX51 G5 PX52 K7 PX53 E4 PX54 E3 PX55 J5 PX56 J4 PX57 H4 PX58 H3 PX59 G3 PB0 A2 PB1 C4 PB2 B4 PB3 A5 PB4 B6 PB5 H12 PB6 D12 PB7 D11 PB8 C8 PB9 E7 PB10 D7 PB11 B2 U101 AT32UC3A3256S 10K R101 1uF C105 VCC RESET_N USB_P USB_N 6810R R102 VUSB VUSB 12 34 56 78 910 STL21-0730 G TT-10U J103 TCK TDO TMS TDI 1uF C111 VCC 12pF C104 12pF C103 22pF C102 22pF C101 1 2 SCP8-32.768KHz TR XC101 10R R103 12 34 56 78 910 TSM-105-01-L-DH-K-TR J101 RF_RST RF_IRQ RF_SEL RF_MISORF_SCLK RF_MOSI RF_SLP_TR RF_MISC 100nF C107 100nF C108 100nF C109 100nF C110 100nF C115 100nF C117 100nF C119 100nF C106 3.3uF C114 3.3uF C116 3.3uF C118 VCCVCCVCC VCCVCC VCC VCC 1 2 3 CD075014 1X3 J102 RF_ID RF_TST RF_CLKM 0R R105 0R R107 0R R106 0R R104 1nF C113 2.2uF C112 100nF C121 VCC 100nF C122 VCC VDDCORE VDDANA RF_IRQ RF_MOSI RF_MISO RF_SEL RF_SCLK RF_CLKM RF_ID RF_TST RF_RST RF_MISC RF_SLP_TR VBUS 1 DN 2 DP 3 GND 4 SHEILD 5 SHEILD 6 J104 USB-A Male USB_N VCC 1uF C123 100nF C127 USB_N USB_P USB_P VUSB VUSB Private & Confidential VCC PCB101 A08-0671 Z101 PCBA Label Place Label on the Bottom Side 1uF C126 1uF C125 1uF C124 3.3uF C120 IN 1 OUT 5 2 BYP 4 ON/OFF 3 GND LP2985AIM5-3.3/NOPB U102 10nF C128 VCC TP111 TP115TP114 TP110 TP109 TP108TP107 TP106 TP105 TP116 A a 1 2 3 CD075014 1X3 J105 UART_RX0 UART_TX0 470R R108 EL17-21USRC LD101 470R R109 EL17-21SYGC LD102 PGB1010603 D103 PGB1010603 D102 39R R110 39R R111 TP101TP102 TP104TP118 TP117 i PCB Rule i PCB Rule 10pF C129 TP120TP121 VUSB TCK TDO TMS TDI JTAG_RST JTAG_RST Place Close To Pin VCC VCC 12 43 FQ5032B-12-C-C-C-200-1 XC102 GSOT05-GS08 D101 TP122TP123TP124TP125TP126TP127TP128 RF_IRQRF_MISORF_MOSIRF_RSTRF_SELRF_SCLKRF_SLP_TR RF_MISC TP129 Place Close to Pins of U101 Place Least Value closer to Pin Place 3.3uF around U101 Place Close to Pins of U101 Place Close to Pins of U101 Place Close to Pins of U101 PIC10101PIC10102 COC101 PIC10201PIC10202 COC102 PIC10301PIC10302 COC103 PIC10401PIC10402 COC104 PIC10501 PIC10502 COC105 PIC10601 PIC10602 COC106 PIC10701 PIC10702 COC107 PIC10801 PIC10802 COC108 PIC10901 PIC10902 COC109 PIC11001 PIC11002 COC110 PIC11101 PIC11102 COC111 PIC11201 PIC11202 COC112 PIC11301 PIC11302 COC113 PIC11401 PIC11402 COC114 PIC11501PIC11502 COC115 PIC11601 PIC11602 COC116 PIC11701 PIC11702 COC117 PIC11801 PIC11802 COC118 PIC11901 PIC11902 COC119 PIC12001 PIC12002 COC120 PIC12101 PIC12102 COC121 PIC12201 PIC12202 COC122 PIC12301 PIC12302 COC123 PIC12401 PIC12402 COC124 PIC12501 PIC12502 COC125 PIC12601 PIC12602 COC126 PIC12701 PIC12702 COC127 PIC12801 PIC12802 COC128 PIC12901PIC12902 COC129 PID10101PID10102 PID10103 COD101 PID10201 PID10202 COD102 PID10301 PID10302 COD103 PIJ10101PIJ10102 PIJ10103PIJ10104 PIJ10105PIJ10106 PIJ10107PIJ10108 PIJ10109PIJ101010 COJ101 PIJ10201 PIJ10202 PIJ10203 COJ102 PIJ10301PIJ10302 PIJ10303PIJ10304 PIJ10305PIJ10306 PIJ10307PIJ10308 PIJ10309PIJ103010 COJ103 PIJ10401 PIJ10402 PIJ10403 PIJ10404 PIJ10405 PIJ10406 COJ104 PIJ10501 PIJ10502 PIJ10503 COJ105 PILD10101 PILD10102 COLD101 PILD10201 PILD10202 COLD102 COPCB101 PIR10101 PIR10102 COR101 PIR10201PIR10202 COR102 PIR10301 PIR10302 COR103 PIR10401PIR10402 COR104 PIR10501PIR10502 COR105 PIR10601PIR10602 COR106 PIR10701PIR10702 COR107 PIR10801PIR10802 COR108 PIR10901PIR10902 COR109 PIR11001PIR11002 COR110 PIR11101PIR11102 COR111 PITP10101 COTP101 PITP10201 COTP102 PITP10401 COTP104 PITP10501 COTP105 PITP10601 COTP106 PITP10701 COTP107 PITP10801 COTP108 PITP10901 COTP109 PITP11001 COTP110 PITP11101 COTP111 PITP11401 COTP114 PITP11501 COTP115 PITP11601 COTP116 PITP11701 COTP117 PITP11801 COTP118 PITP12001 COTP120 PITP12101 COTP121 PITP12201 COTP122 PITP12301 COTP123 PITP12401 COTP124 PITP12501 COTP125 PITP12601 COTP126 PITP12701 COTP127 PITP12801 COTP128 PITP12901 COTP129 PIU1010A1 PIU1010A2 PIU1010A3 PIU1010A4 PIU1010A5 PIU1010A6 PIU1010A7 PIU1010A8 PIU1010A9 PIU1010A10 PIU1010A11 PIU1010A12 PIU1010B1 PIU1010B2 PIU1010B3 PIU1010B4 PIU1010B5 PIU1010B6 PIU1010B7 PIU1010B8 PIU1010B9 PIU1010B10 PIU1010B11 PIU1010B12PIU1010C1 PIU1010C2 PIU1010C3 PIU1010C4 PIU1010C5 PIU1010C6 PIU1010C7 PIU1010C8 PIU1010C9 PIU1010C10 PIU1010C11 PIU1010C12 PIU1010D1 PIU1010D2 PIU1010D3 PIU1010D4 PIU1010D5 PIU1010D6 PIU1010D7 PIU1010D8 PIU1010D9 PIU1010D10 PIU1010D11PIU1010D12 PIU1010E1 PIU1010E2 PIU1010E3 PIU1010E4 PIU1010E5 PIU1010E6 PIU1010E7 PIU1010E8 PIU1010E9 PIU1010E10 PIU1010E11 PIU1010E12 PIU1010F1 PIU1010F2 PIU1010F3 PIU1010F4 PIU1010F5 PIU1010F6PIU1010F7 PIU1010F8 PIU1010F9 PIU1010F10 PIU1010F11 PIU1010F12 PIU1010G1 PIU1010G2 PIU1010G3 PIU1010G4 PIU1010G5 PIU1010G6PIU1010G7 PIU1010G8 PIU1010G9 PIU1010G10 PIU1010G11 PIU1010G12PIU1010H1 PIU1010H2 PIU1010H3 PIU1010H4 PIU1010H5 PIU1010H6 P…

Text truncated - open the document above for the full version.

Nemko AS, Gaustadalléen 30, P.O.Box 73 Blindern, NO-0314 Oslo Norway T +47 22 96 03 30 F +47 22 96 05 50 Enterprise number NO974404532 Visiting address: Nemko Kjeller, Instituttveien 6, P.O.Box 96, NO-2027 Kjeller Norway T +47 64 84 57 00 F +47 64 84 57 05 Test report no. : 140235-13 Item tested : A09-0491 Type of equipment : IEEE 802.15.4, 902 - 928 MHz Evaluation Module FCC ID : VW4A09-0491 Client : Atmel Norway AS FCC Part 15.247 Digital Transmission System RSS-210 Issue 7 & RSS Gen Issue 2 Low Power Licence-Exempt Radio communication Devices 09 March 2010 Authorized by : .............................................. Frode Sveinsen Technical Verificator TEST REPORT FCC part 15C Project no.: 140235-13 FCC ID: VW4A09-0491 Nemko AS, NO-2027 Kjeller Page 2 (41) CONTENTS 1 GENERAL INFORMATION ...................................................................................................... 3 1.1 Testhouse Info .......................................................................................................................... 3 1.2 Client Information ...................................................................................................................... 3 1.3 Manufacturer ............................................................................................................................. 3 2 Test Information ...................................................................................................................... 4 2.1 Test Item .............................................................................…

Text truncated - open the document above for the full version.