W7O24WN0802.11BGN 1X1 MODULE

 2015 Microchip Technology Inc.Advance InformationDS00000A-page 1 MRF24WN0MA/MB Features • IEEE 802.11b/g/n compliant transceiver • 2.4 GHz IEEE 802.11n Single Stream 1x1 • SPI Interface to Host Controller (4-wire including interrupt) • Works with Microchip's MPLAB ® Harmony Integrated Software Framework • Fully integrated wireless module with voltage regulation, crystal, RF matching circuitry, PA, LNA, and PCB trace antenna • Ultra-small W.FL connector for external antennas (MRF24WN0MB) • Compact surface mount module: 0.700" x 1.050" x 0.085 inch (17.8 mm x 26.7 mm x 2.2 mm) • Castellated surface mount pads for easy and reliable PCB mounting • Environmentally friendly, RoHS compliant Operational • Single Operating Voltage: 3.15V to 3.45V (3.3V typical) • Temperature Range: -40°C to +85°C Industrial • Low Current Consumption: - RX mode: 60 mA (typical) - TX mode: 115 mA at 0 dBm; 230 mA at 18 dBm (typical) • Power Saving Mode: - Hibernate: 5 μA (typical) RF/Analog • Frequency: 2.400 to 2.484 GHz • Channels: 1-13 • Modulation: DSSS, CCK, BPSK, QPSK, 16QAM, 64QAM • Sensitivity: -94 dBm Antenna • Integral PCB Trace Antenna (MRF24WN0MA) • External Antenna (MRF24WN0MB) Compliance • Modular certified for the United States (FCC) and Canada (IC) • European R&TTE Directive Assessed Radio Module • Australia, New Zealand, Korea, Taiwan, Japan Applications • Utility and Smart Energy • Consumer Electronics • Industrial Controls • Remote Device Management • Retail • Medical, Fitness, and Health Care 2.4 GHz IEEE 802.11b/g/n Wireless Module MRF24WN0MA/MB DS00000A-page 2Advance Information 2015 Microchip Technology Inc. Table of Contents 1.0Device Overview .......................................................................................................................................................................... 3 2.0Circuit Description .......................................................................................................................................................................11 3.0Application Information ............................................................................................................................................................... 15 4.0Regulatory Approval ................................................................................................................................................................... 21 5.0Electrical Characteristics ............................................................................................................................................................ 27 Appendix A: Revision History ............................................................................................................................................................... 29 The Microchip Web Site ....................................................................................................................................................................... 31 Customer Change Notification Service ................................................................................................................................................ 31 Customer Support ................................................................................................................................................................................ 31 Product Identification System............................................................................................................................................................... 33 TO OUR VALUED CUSTOMERS It is our intention to provide our valued customers with the best documentation possible to ensure successful use of your Microchip products. To this end, we will continue to improve our publications to better suit your needs. Our publications will be refined and enhanced as new volumes and updates are introduced. If you have any questions or comments regarding this publication, please contact the Marketing Communications Department via E-mail at [email protected]. We welcome your feedback. Most Current Data Sheet To obtain the most up-to-date version of this data sheet, please register at our Worldwide Web site at: http://www.microchip.com You can determine the version of a data sheet by examining its literature number found on the bottom outside corner of any page. The last character of the literature number is the version number, (e.g., DS30000000A is version A of document DS30000000). Errata An errata sheet, describing minor operational differences from the data sheet and recommended workarounds, may exist for current devices. As device/documentation issues become known to us, we will publish an errata sheet. The errata will specify the revision of silicon and revision of document to which it applies. To determine if an errata sheet exists for a particular device, please check with one of the following: • Microchip’s Worldwide Web site; http://www.microchip.com • Your local Microchip sales office (see last page) When contacting a sales office, please specify which device, revision of silicon and data sheet (include literature number) you are using. Customer Notification System Register on our web site at www.microchip.com to receive the most current information on all of our products.  2015 Microchip Technology Inc.Advance InformationDS00000A-page 3 MRF24WN0MA/MB 1.0DEVICE OVERVIEW The MRF24WN0MA and MRF24WN0MB are low-power, 2.4 GHz, IEEE 802.11n-compliant, surface mount modules with all associated RF components: crystal oscillator, bypass and bias passives with integrated MAC, baseband, RF and power amplifier, and built-in hardware support for encryption. See Figure 1-1. The integrated module design frees the designer from RF and antenna design tasks and regulatory compliance testing, ultimately providing quicker time to market. The MRF24WN0MA/MB modules are designed to be used with Microchip's MPLAB ® Harmony Integrated Software Framework. The integrate…

Text truncated - open the document above for the full version.

Applicant/Grantee Microchip Technology Inc/Steve Caldwell FCC ID: W7O24WN0 Section 15.212 Modular Transmitters Request for Modular Approval X Request for Limited Modular Approval Requirements EUT Conditions Comply (Y/N) Single Modular Approval Requirements 1 The radio elements of the modular transmitter must have their own shielding. The physical crystal and tuning capacitors may be located external to the shielded radio elements. yes 2 The modular transmitter must have buffered modulation/data inputs (if such inputs are provided) to ensure that the module will comply with Part 15 requirements under conditions of excessive data rates or over-modulation. yes 3 The modular transmitter must have its own power supply regulation. yes 4 The modular transmitter must comply with the antenna and transmission system requirements of Sections 15.203, 15.204(b) and 15.204(c). The antenna must either be permanently attached or employ a “unique” antenna coupler (at all connections between the module and the antenna, including the cable). The “professional installation” provision of Section 15.203 is not applicable to modules but can apply to limited modular approvals under paragraph (b) of this section. yes 5 The modular transmitter must be tested in a stand-alone configuration, i.e., the module must not be inside another device during testing for compliance with Part 15 requirements. Unless the transmitter module will be battery powered, it must comply with the AC line conducted requirements found in Section 15.207. AC or DC power lines and data input/output lines connected to the module must not contain ferrites, unless they will be marketed with the module (see Section 15.27(a)). The length of these lines shall be the length typical of actual use or, if that length is unknown, at least 10 centimeters to insure that there is no coupling between the case of the module and supporting yes equipment. Any accessories, peripherals, or support equipment connected to the module during testing shall be unmodified and commercially available (see Section 15.31(i)). 6 The modular transmitter must be equipped with either a permanently affixed label or must be capable of electronically displaying its FCC identification number. (A) If using a permanently affixed label, the modular transmitter must be labeled with its own FCC identification number, and, if the FCC identification number is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as the following: “Contains Transmitter Module FCC ID: XYZMODEL1” or “Contains FCC ID: XYZMODEL1.” Any similar wording that expresses the same meaning may be used. The Grantee may either provide such a label, an example of which must be included in the application for equipment authorization, or, must provide adequate instructions along with the module which explain this requirement. In the latter case, a copy of these instructions must be included in the application for equipment authorization. (B) If the modular transmitter uses an electronic display of the FCC identification number, the information must be readily accessible and visible on the modular transmitter or on the device in which it is installed. If the module is installed inside another device, then the outside of the device into which the module is installed must display a label referring to the enclosed module. This exterior label can use wording such as the following: “Contains FCC certified transmitter module(s).” Any similar wording that expresses the same meaning may be used. The user manual must include instructions on how to access the electronic display. A copy of these instructions must be included in the application for equipment authorization. yes 7 The modular transmitter must comply with any specific rules or operating requirements that ordinarily apply to a complete transmitter and the manufacturer must provide adequate instructions along with the module to explain any such requirements. A copy of these instructions must be included in the application for equipment authorization. yes 8 The modular transmitter must comply with any applicable RF exposure requirements in its final configuration. yes A limited modular approval may be granted for single or split modular transmitters that do not comply with all of the above requirements, e.g., shielding, minimum signaling amplitude, buffered modulation/data inputs, or power supply regulation, if the manufacturer can demonstrate by alternative means in the application for equipment authorization that the modular transmitter meets all the applicable Part 15 requirements under the operating conditions in which the transmitter will be used. Limited modular approval also may be granted in those instances where compliance with RF exposure rules is demonstrated only for particular product configurations. The applicant for certification must state how control of the end product into which the module will be installed will be maintained such that full compliance of the end product is always ensured.

The antenna type is; printed circuit board inverted F structure. The antenna gain is -1.0 dBi Then connector type is W.Fl

FCC ID LABEL AND LOCATION THE MODEL NUMBER IS LASER ETCHED ON TOP OF MODULE ON RF SHIELD APPLIES TO MRF24WN0MA, MRF24WN0MB, RN1810, RN1810E, RN1811, RN1811E Bottom of Module FCC /IC Label silkscreen on bottom of PCB in this Location

FCC Part 1 Subpart I FCC Part 2 Subpart J INDUSTRY CANADA RSS 102 ISSUE 3 RF EXPOSURE REPORT FOR 802.11BGN 1X1 MODULE MODEL NUMBER: MRF24WN0MA, MRF24WN0MB RN1810, RN1810E RN1811, RN1811E FCC ID: W7O24WN0 IC: 7693A-24WN0 REPORT NUMBER: 14U19707-E2A ISSUE DATE:JULY 22, 2015 Prepared for MICROCHIP TECHNOLOGY INC. 450 HOLGER WAY SAN JOSE, CA 95134-1368, U.S.A. Prepared by UL VERIFICATION SERVICES INC. 47173 BENICIA STREET FREMONT, CA 94538, U.S.A. TEL: (510) 771-1000 FAX: (510) 661-0888 REPORT NO: 14U19707-E2A DATE: JULY 22, 2015 FCC ID: W7O24WN0 IC: 7693A-24WN0 Page 2 of 12 UL VERIFICATION SERVICES INC. FORM NO: CCSUP4701I 47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 771-1000 FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of . UL Verification Services Inc. Revision History Rev. Issue Date Revisions Revised By -- 06/24/15 Initial Issue C. Pang A 07/22/15 Added model numbers RN1810, RN1810E RN1811, RN1811E S. Kuwatani REPORT NO: 14U19707-E2A DATE: JULY 22, 2015 FCC ID: W7O24WN0 IC: 7693A-24WN0 Page 3 of 12 UL VERIFICATION SERVICES INC. FORM NO: CCSUP4701I 47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 771-1000 FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of . UL Verification Services Inc. TABLE OF CONTENTS 1. ATTESTATION OF TEST RESULTS ................................................................................. 4 2. TEST METHODOLOGY ..................................................................................................... 5 3. REFERENCES ................................................................................................................... 5 4. FACILITIES AND ACCREDITATION ................................................................................. 5 5. MAXIMUM PERMISSIBLE RF EXPOSURE ....................................................................... 6 5.1. FCC RULES ................................................................................................................ 6 5.2. IC RULES .................................................................................................................... 7 5.3. EQUATIONS ................................................................................................................ 8 5.4. LIMITS AND IC EXEMPTION .....................................................................................10 6. RF EXPOSURE RESULTS ................................................................................................11 REPORT NO: 14U19707-E2A DATE: JULY 22, 2015 FCC ID: W7O24WN0 IC: 7693A-24WN0 Page 4 of 12 UL VERIFICATION SERVICES INC. FORM NO: CCSUP4701I 47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 771-1000 FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of . UL Verification Services Inc. 1. ATTESTATION OF TEST RESULTS COMPANY NAME: MICROCHIP TECHNOLOGY INC. 450 HOLGER WAY SAN JOSE, CA 95134-1368, U.S.A. EUT DESCRIPTION: 802.11BGN 1X1 MODULE MODEL: MRF24WN0MA, MRF24WN0MB RN1810, RN1810E RN1811, RN1811E SERIAL NUMBER: FAL B018 DATE TESTED: APRIL 01, 2015 TO APRIL 27, 2015 APPLICABLE STANDARDS STANDARD TEST RESULTS FCC PART 1 SUBPART I & PART 2 SUBPART J Pass INDUSTRY CANADA RSS 102 ISSUE 3 Pass UL Verification Services Inc. calculated the RF Exposure of the above equipment in accordance with the requirements set forth in the above standards, using test results reported in the test report documents referenced below and/or documentation furnished by the applicant. All indications of Pass/Fail in this report are opinions expressed by UL Verification Services Inc. based on interpretations of these calculations. The results show that the equipment is capable of demonstrating compliance with the requirements as documented in this report. Note: The results documented in this report apply only to the tested sample, under the conditions and modes of operation as described herein. This document may not be altered or revised in any way unless done so by UL Verification Services Inc. and all revisions are duly noted in the revisions section. Any alteration of this document not carried out by UL Verification Services Inc. will constitute fraud and shall nullify the document. This report must not be used by the client to claim product certification, approval, or endorsement by NVLAP, NIST, any agency of the Federal Government, or any agency of any government. Approved & Released For UL Verification Services Inc. By: Calculated By: CHIN PANG CHRIS XIONG SENIOR ENGINEER LAB ENGINEER UL VERIFICATION SERVICES INC. UL VERIFICATION SERVICES INC. REPORT NO: 14U19707-E2A DATE: JULY 22, 2015 FCC ID: W7O24WN0 IC: 7693A-24WN0 Page 5 of 12 UL VERIFICATION SERVICES INC. FORM NO: CCSUP4701I 47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 771-1000 FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of . UL Verification Services Inc. 2. TEST METHODOLOGY All calculations were made in accordance with FCC OET Bulletin 65 Edition 97-01 and IC Safety Code 6. 3. REFERENCES All measurements were made as documented in test report UL Verification Services Inc., UL Verification Services Inc. Document 14U19707-E1 for operation in the 2.4 GHz band Output power, Duty cycle and Antenna gain data is excerpted from the applicable test reports. Output power, Duty cycle and Antenna gain data is excerpted from product documentation provided by the applicant. Antenna gain data is excerpted from the applicable test reports. Antenna gain data is excerpted from product documentation provided by the applicant. 4. FACILITIES AND ACCREDITATION The test sites and measurement facilities used to collect data are located at 47173 Benicia Street, Fremont, California, USA. UL Verification Services Inc. is accredited by NVLAP, Laboratory Code 200065-0. The full scope of accreditation can be viewed at http://ts.nist.…

Text truncated - open the document above for the full version.

FCC 47 CFR PART 15 SUBPART C INDUSTRY CANADA RSS-247 ISSUE 1 CERTIFICATION TEST REPORT FOR 802.11BGN 1X1 MODULE MODEL NUMBERS: MRF24WN0MA, MRF24WN0MB RN1810, RN1810E RN1811, RN1811E FCC ID: W7O24WN0 IC: 7693A-24WN0 REPORT NUMBER: 14U19707-E1C ISSUE DATE: AUGUST 18, 2015 Prepared for MICROCHIP TECHNOLOGY INC. 450 HOLGER WAY SAN JOSE, CA 95134-1368, U.S.A. Prepared by UL VERIFICATION SERVICES INC. 47173 BENICIA STREET FREMONT, CA 94538, U.S.A. TEL: (510) 771-1000 FAX: (510) 661-0888 REPORT NO: 14U19707-E1C DATE: AUGUST 18, 2015 FCC ID: W7O24WN0 IC: 7693A-24WN0 Page 2 of 356 UL VERIFICATION SERVICES INC. FORM NO: CCSUP4701J 47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 771-1000 FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL Verification Services Inc. Revision History Rev. Issue Date Revisions Revised By -- 04/28/2015 Initial Issue C. Pang A 07/22/2015 Add Model numbers RN1810, RN1810E RN1811, RN1811E S. Kuwatani B 07/29/2015 Correction on Page 14 and 28 C. Pang C 08/18/2015 Address TCB’s questions C. Pang REPORT NO: 14U19707-E1C DATE: AUGUST 18, 2015 FCC ID: W7O24WN0 IC: 7693A-24WN0 Page 3 of 356 UL VERIFICATION SERVICES INC. FORM NO: CCSUP4701J 47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 771-1000 FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL Verification Services Inc. TABLE OF CONTENTS 1. ATTESTATION OF TEST RESULTS ................................................................................. 5 2. TEST METHODOLOGY ..................................................................................................... 6 3. FACILITIES AND ACCREDITATION ................................................................................. 6 4. CALIBRATION AND UNCERTAINTY ................................................................................ 7 4.1. MEASURING INSTRUMENT CALIBRATION .............................................................. 7 4.2. SAMPLE CALCULATION ............................................................................................ 7 4.3. MEASUREMENT UNCERTAINTY ............................................................................... 7 5. EQUIPMENT UNDER TEST ............................................................................................... 8 5.1. DESCRIPTION OF EUT .............................................................................................. 8 5.2. MAXIMUM OUTPUT POWER...................................................................................... 8 5.3. DESCRIPTION OF AVAILABLE ANTENNAS .............................................................. 8 5.4. SOFTWARE AND FIRMWARE .................................................................................... 8 5.5. WORST-CASE CONFIGURATION AND MODE .......................................................... 9 5.6. DESCRIPTION OF TEST SETUP ...............................................................................10 6. TEST AND MEASUREMENT EQUIPMENT ......................................................................12 7. MEASUREMENT METHODS ............................................................................................13 8. ON TIME, DUTY CYCLE AND MEASUREMENT METHODS ...........................................14 8.1. DUTY CYCLE PLOTS ................................................................................................15 9. ANTENNA PORT TEST RESULTS ...................................................................................17 9.1. 802.11b SISO MODE IN THE 2.4 GHz BAND ............................................................17 9.1.1. 6 dB BANDWIDTH ...............................................................................................17 9.1.2. 99% BANDWIDTH ...............................................................................................21 9.1.3. AVERAGE POWER .............................................................................................25 9.1.4. OUTPUT POWER ...............................................................................................26 9.1.5. PSD .....................................................................................................................28 9.1.6. OUT-OF-BAND EMISSIONS ...............................................................................32 9.2. 802.11g SISO MODE IN THE 2.4 GHz BAND ............................................................38 9.2.1. 6 dB BANDWIDTH ...............................................................................................38 9.2.2. 99% BANDWIDTH ...............................................................................................43 9.2.3. AVERAGE POWER .............................................................................................48 9.2.4. OUTPUT POWER ...............................................................................................49 9.2.5. PSD .....................................................................................................................51 9.2.6. OUT-OF-BAND EMISSIONS ...............................................................................56 9.3. 802.11n HT20 SISO MODE IN THE 2.4 GHz BAND ...................................................64 9.3.1. 6 dB BANDWIDTH ...............................................................................................64 9.3.2. 99% BANDWIDTH ...............................................................................................69 REPORT NO: 14U19707-E1C DATE: AUGUST 18, 2015 FCC ID: W7O24WN0 IC: 7693A-24WN0 Page 4 of 356 UL VERIFICATION SERVICES INC. FORM NO: CCSUP4701J 47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 771-1000 FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL Verification Services Inc. 9.3.3. AVERAGE POWER ............................................................…

Text truncated - open the document above for the full version.

REPORT NO: 14U19707-E1C DATE: AUGUST 18, 2015 FCC ID: W7O24WN0 IC: 7693A-24WN0 Page 101 of 356 UL VERIFICATION SERVICES INC. FORM NO: CCSUP4701J 47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 771-1000 FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL Verification Services Inc. RESULTS Limits ChannelFrequencyDirectionalFCCICICMax GainPowerPowerEIRPPower LimitLimitLimit (MHz)(dBi)(dBm)(dBm)(dBm)(dBm) Low24222.0030.00303630.00 Mid24372.0030.00303630.00 High24422.0030.00303630.00 High24472.0030.00303630.00 High24522.0030.00303630.00 Results ChannelFrequencyTotalPowerMargin MeasCorr'dLimit PowerPower (MHz)(dBm)(dBm)(dBm)(dB) Low242215.9515.9530.00-14.05 Mid243719.8219.8230.00-10.18 High244218.7818.7830.00-11.22 High244717.0417.0430.00-12.96 High2452 14.43 14.4330.00-15.57 REPORT NO: 14U19707-E1C DATE: AUGUST 18, 2015 FCC ID: W7O24WN0 IC: 7693A-24WN0 Page 102 of 356 UL VERIFICATION SERVICES INC. FORM NO: CCSUP4701J 47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 771-1000 FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL Verification Services Inc. 9.4.5. PSD LIMITS FCC §15.247 IC RSS-210 A8.2 RESULTS PSD Results ChannelFrequency LimitMargin Meas (MHz)(dBm) (dBm)(dB) Low2422-15.71 8.0-23.7 Mid2437-14.37 8.0-22.4 High2442-16.11 8.0-24.1 High2447-20.94 8.0-28.9 High2452-20.90 8.0-28.9 REPORT NO: 14U19707-E1C DATE: AUGUST 18, 2015 FCC ID: W7O24WN0 IC: 7693A-24WN0 Page 103 of 356 UL VERIFICATION SERVICES INC. FORM NO: CCSUP4701J 47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 771-1000 FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL Verification Services Inc. PSD PSD, LOW CH PSD, MID CH REPORT NO: 14U19707-E1C DATE: AUGUST 18, 2015 FCC ID: W7O24WN0 IC: 7693A-24WN0 Page 104 of 356 UL VERIFICATION SERVICES INC. FORM NO: CCSUP4701J 47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 771-1000 FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL Verification Services Inc. PSD, HIGH CH 7 PSD, HIGH CH 8 REPORT NO: 14U19707-E1C DATE: AUGUST 18, 2015 FCC ID: W7O24WN0 IC: 7693A-24WN0 Page 105 of 356 UL VERIFICATION SERVICES INC. FORM NO: CCSUP4701J 47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 771-1000 FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL Verification Services Inc. PSD, HIGH CH 9 REPORT NO: 14U19707-E1C DATE: AUGUST 18, 2015 FCC ID: W7O24WN0 IC: 7693A-24WN0 Page 106 of 356 UL VERIFICATION SERVICES INC. FORM NO: CCSUP4701J 47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 771-1000 FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL Verification Services Inc. 9.4.6. OUT-OF-BAND EMISSIONS LIMITS FCC §15.247 (d) IC RSS-210 A8.5 In any 100 kHz bandwidth outside the frequency band in which the spread spectrum or digitally modulated intentional radiator is operating, the radio frequency power that is produced by the intentional radiator shall be at least 20 dB below that in the 100 kHz bandwidth within the band that contains the highest level of the desired power, based on either an RF conducted or a radiated measurement, provided the transmitter demonstrates compliance with the peak conducted power limits. If the transmitter complies with the conducted power limits based on the use of RMS averaging over a time interval, as permitted under paragraph (b)(3) of this section, the attenuation required under this paragraph shall be 30 dB instead of 20 dB. Attenuation below the general limits specified in §15.209(a) is not required. REPORT NO: 14U19707-E1C DATE: AUGUST 18, 2015 FCC ID: W7O24WN0 IC: 7693A-24WN0 Page 107 of 356 UL VERIFICATION SERVICES INC. FORM NO: CCSUP4701J 47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 771-1000 FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL Verification Services Inc. RESULTS IN-BAND REFERENCE LEVEL REFERENCE LEVEL MID CH REPORT NO: 14U19707-E1C DATE: AUGUST 18, 2015 FCC ID: W7O24WN0 IC: 7693A-24WN0 Page 108 of 356 UL VERIFICATION SERVICES INC. FORM NO: CCSUP4701J 47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 771-1000 FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL Verification Services Inc. LOW CHANNEL BANDEDGE HIGH CHANNEL 7 BANDEDGE AUTHORIZED BAND EDGE LOW CH AUTHORIZED BAND EDGE HIGH CH 7 REPORT NO: 14U19707-E1C DATE: AUGUST 18, 2015 FCC ID: W7O24WN0 IC: 7693A-24WN0 Page 109 of 356 UL VERIFICATION SERVICES INC. FORM NO: CCSUP4701J 47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 771-1000 FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL Verification Services Inc. HIGH CHANNEL 8 BANDEDGE HIGH CHANNEL 9 BANDEDGE AUTHORIZED BAND EDGE HIGH CH 8 AUTHORIZED BAND EDGE HIGH CH 9 REPORT NO: 14U19707-E1C DATE: AUGUST 18, 2015 FCC ID: W7O24WN0 IC: 7693A-24WN0 Page 110 of 356 UL VERIFICATION SERVICES INC. FORM NO: CCSUP4701J 47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 771-1000 FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL Verification Services Inc. OUT-OF-BAND EMISSIONS OUT OF BAND LOW CH OUT OF BAND MID CH REPORT NO: 14U19707-E1C DATE: AUGUST 18, 2015 FCC ID: W7O24WN0 IC: 7693A-24WN0 Page 111 of 356 UL VERIFICATION SERVICES INC. FORM NO: CCSUP4701J 47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 771-1000 FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL Verification Services Inc. OUT OF BAND HIGH CH 7 OUT OF BAND HIGH CH 8 REPORT NO: 14U19707-E1C DATE: AUGUST 18, 2015 FCC ID: W7O24WN0 IC: 7693A-24WN0 Page 112 of 356 UL VERIFICATION SERVICES INC. FORM NO: CCSUP4701J 47173 …

Text truncated - open the document above for the full version.

REPORT NO: 14U19707-E1C DATE: AUGUST 18, 2015 FCC ID: W7O24WN0 IC: 7693A-24WN0 Page 201 of 356 UL VERIFICATION SERVICES INC. FORM NO: CCSUP4701J 47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 771-1000 FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL Verification Services Inc. DATA Marker Frequenc y (GHz) Meter Reading (dBuV) Det AF T344 (dB/m) Amp/Cbl/ Fltr/Pad (dB) DC Corr (dB) Correct…

Text truncated - open the document above for the full version.