WIJVVINWIFIIEEE 802.11b/g/n Half-Mini-Card Wireless Module

VVINWIFI 1 IEEE 802.11b/g/n USB Half-Mini-Card Wireless Module irements by using VVINWIFI. Compliant with the IEEE 802.11b/g/n standard, the VVINWIFI uses Direct Sequence Spread wireless module ---VVINWIFI. The VVINWIFI USB Half- 2 I. Introduction i ii i. Overview . Overview. Overview . Overview AzureWave Technologies, Inc. introduces the pioneer of the IEEE 802.11b/g/n USB Half-Mini-Card Mini-Card wireless module is a highly integrated wireless local area network (WLAN) solution to let users enjoy the digital content through the latest wireless technology without using the extra cables and cords. It enables a high performance, cost effective, low power, compact solution that easily fits onto one side of a USB Half-Mini-Card. Spectrum (DSSS), Orthogonal Frequency Division Multiplexing (OFDM), BPSK, QPSK, CCK and QAM baseband modulation technologies. A high level of integration and full implementation of the power management functions specified in the IEEE 802.11 standard minimize system power requ Longer Range and Faster Speed Comparing to 802.11g technology, 802.11n draft 3.0 standard make big improvement on speed and range. It Increases wireless range by up to 2 times and reduces dead spots in coverage area. The data rate can up to 150Mbps data rate. ii. Features USB Half-Mini-Card. Compliant with IEEE802.11n Draft 3.0 standard 2 antennas to support 1(Transmit) × ×× × 1(Receive) Diversity technology High speed wireless connection up to 150MbpsLow power consumption and high performance Enhanced wireless security 3 iii. Product Review 1. Connection Mode ◎Infrastructure Mode Infrastructure mode needs an access point to establish the network, which can provide wireless accesses within valid range for users to communicate with others or transmit data with a wired network. There are several benefits of Infrastructure networking: √ Roaming: a wireless LAN enabled computer can physically move from the operating range of one access point to the other without losing connection. There is a quick association made between new access point and wireless device as the computer traverses from the coverage of one access point to another. √ Range Extension: each wireless LAN enabled computer within the range of access point can communicate with other wireless LAN enabled computers within the effective range from the access point. √ Wired to wireless LAN connection: the access point will establish a bridge between wireless LAN and other wired counterparts. Infrastructure Mode 4 ◎Ad-hoc Mode The difference between Ad-hoc mode and Infrastructure mode is that Ad-hoc mode does not need the access point or router. When you use this mode, your computer will act as a server within the valid range and connect directly to others in the same LAN workgroup. Ad-hoc Mode It is recommended to choose this mode when there is no access point showed on your wireless network. 5 II. Installation i. System Requirements *Minimum of 64MB system memory *Operating system: XP/Vista * Driver installation ii. Setup: Windows XP OS 1. Find out the Driver, and launch the Setup Wizard 6 2. Please wait few seconds for wizard to prepare installation 3. Please select click [Install] to proceed 7 4. The Wizard is running installation 5. Please wait few seconds for Wizard to setup 8 6. When it is completed, please click [Finish] iii. Setup: Windows Vista OS Please follow the steps to complete installation. 1. Launch the setup driver 9 2. When you see the permission dialogue box, please click [Continue] 3. Now the Wizard is preparing installation 10 4. Please click [Install] to proceed 5. The system is processing installation 11 6. Please wait few seconds for Wizard to setup 7. When the setup is completed, please click [Finish] 12 III. Network Connection i. For Windows XP OS Please see the following steps to setup network connection for Windows XP. 1. Find the network icon on the desktop shortcut and right-click on it. Choose “View Available Wireless networks” 2. You will see several options, please select one and click [Connect] 13 3. Please wait for few seconds to let system connecting to selected wireless network 4. You may need to type the network key when it is required (if the network doesn’t request the key, the network will connect directly.) 5. Now the selected wireless network is connected 14 6. You can check the connection status by clicking [Status] in the pop-up dialogue 7. Here is the wireless network connection status ii. For Windows Vista OS Following are the instructions to setup wireless connection for Windows Vista. 1. Right-click on the network icon located on desktop shortcut. When you see the dialogue, please click [Connect to a network] 15 2. Choose wireless network within your range and click [Connect] * If selected network is not secure, please choose [Connect anyway] 3. You may need to wait for few seconds when Windows connects to wireless network 16 4. Now the selected wireless network is connected 5. If you want to see the connection status, please right-click on the network you choose and select [Status] 17 6. This is the information of network status 18 IV. Setup for Ad-hoc Mode i. For Windows XP OS If you want to choose Ad-hoc mode, please right-click network icon on desktop shortcut and choose “Open Network Connections”, or go to [Control Panel] and double-click “Network Connection” icon. When you see the “Network Connections” screen, please follow the steps below to setup Ad-hoc mode. 19 1. Double-click “Wireless Network Connection” icon to enter its properties 2. Click "General” tab and double-click the “Internet Protocol (TCP/IP)” item 20 3. Choose “Use the following IP address:” and type the IP address; then click [OK] *Note: the IP address of the other wireless card should be set with the same subnet mask 4. Right-click the “Wireless Network Connection” icon and choose “properties” 21 5. Select “Wireless Network” tab and choose [Add] 6. Type “Network name (SSID)” and choose “Data encryption” if you want to…

Text truncated - open the document above for the full version.

SCS-F18: Project and Product Certification Representative Authorization Letter Page 1 of 2 Rev 2.0 2206 Ringwood Avenue San Jose, CA 95131 Tel: 408-526-1188 Fax: 408-526-1088 Email: [email protected] Project and Product Certification Representative Authorization Letter Reason for Amendment (current / obsolete) Revision History Approved Date From To Initial Release (current) 1.0 1.0 Nov-14-2006 Revised wording (current) 1.0 2.0 Sept–25-2007 SCS-F18: Project and Product Certification Representative Authorization Letter Page 2 of 2 Rev 2.0 VideoHome Technology Corp. Jan. 26, 2011 To: SIEMIC, INC. 2206 Ringwood Avenue, San Jose, CA 95131 USA Dear Sir/Madam, Re: Project and Product Certification Representative Authorization Letter We, Amtek System Co., Ltd. hereby authorize SIEMIC, INC. to act as a Certification Body for certifying for the following project(s): IEEE 802.11b/g/n Half-Mini-Card Wireless Module, VVINWIFI We affirm that between SIEMIC and VideoHome Technology Corp. any difference in understanding, including test plan, measurement methods, applicable standards and relevant procedures and processes have been resolved prior to commencement of testing activities. Sincerely, Authorized Person: Jeff Yu Title of Authorized Person: R/D Director VideoHome Technology Corp. Address: 4F-1,No.190/192,Da Tung Rd.,Sec.3,Hsichih Dist, New Taipei City 221,TAIWAN

SCS-F19: Confidentiality Request Letter Page 1 of 3 Rev 2.0 2206 Ringwood Avenue San Jose, CA 95131 Tel: 408-526-1188 Fax: 408-526-1088 Email: [email protected] Confidentiality Request Letter Reason for Amendment (current / obsolete) Revision History Approved Date From To Initial Release (current) 1.0 1.0 Nov-14-2006 Adding CFR 2.459 1.0 2.0 August – 11 - 2008 SCS-F19: Confidentiality Request Letter Page 2 of 3 Rev 2.0 VideoHome Technology Corp. Jan. 06, 2011 To: Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD Subject: Permanent Confidentiality Request for FCC ID: WIJVVINWIFI We hereby request confidential treatment of information accompanying this application as outlined below: - Schematics –VVIN3575 Sechematic.pdf - Operational description - VVIN3575 Operation Description.pdf - Block Diagram- VVIN3575 Block Diagram.pdf The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. The applicant understands that pursuant to Section 0.457 & 0.459 of the Rules, disclosure of this application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely, Client’s signature : Client’s name / title : R/D Director Contact information / address : VideoHome Technology Corp. Address: 4F-1,No.190/192,Da Tung Rd., Sec.3, Hsichih Dist., New Taipei City 221,TAIWAN SCS-F19: Confidentiality Request Letter Page 3 of 3 Rev 2.0 (Client’s Company Letterhead/log) (Current Date) To: Federal Communications Commission Office of Engineering and Technology Equipment Authorization Division 7345 Oakland Mills Road Columbia, Maryland 21046 Subject: Short Term Confidentiality Request for FCC ID: XXXXXXXXXX To Whom It May Concern: Pursuant to sections 0.457 and 0.459 of CFR 47 and to avoid premature release of sensitive information prior to marketing or release of the product to the public, the applicant requests the following documents contained in this certification application be temporarily withheld from public disclosure for an initial period of 45 days: - User Manual - User Manual Insert - ..................etc The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. Sincerely, Client’s signature : xxxxxxx Client’s name / title : xxxxxxx Contact information / address : xxxxxxx

SCS-F26 Modular Approval Letter Page 1 of 1 Rev 3.0 VideoHome Technology Corp. Jan. 11, 2011 (PC2TVwifi) FCC ID : WIJVVINWIFI, is seeking FCC Authorization as a ■Modular transmitter / Limited Modular Approval (Please check one). The EUT meets the requirements for ■Modular approval / Limited Modular Approval (please check one) as detailed in FCC public Notice DA00-1407. Compliance to each of the requirements is described below: Questions are: 1. “The modular transmitter must have its own RF shielding.” ■ Yes / No 2. “The modular transmitter must have buffered modulation/data inputs.” ■ Yes / No 3. “The modular transmitter must have its own power supply regulation.” ■ Yes / No 4. “The modular transmitter must comply with the antenna requirements of section 15.203 and 15.204(c).” ■Yes / No 5. “The modular transmitter must be tested in a stand-alone configuration.” ■Yes / No 6. “The modular transmitter must be labeled with its own FCC ID number.” ■ Yes / No 7. “The modular transmitter must comply with any specific rule or operating requirements applicable to the transmitter and the manufacture must provide adequate instruction along with the module to explain any such requirements.” ■Yes / No 8. “The modular transmitter must comply with any applicable RF exposure requirements.” ■Yes / No Client’s signature: Client’s name / title: Jeff Yu/ R/D Director Contact information / address: VideoHome Technology Corp. Address: 4F-1,No.190/192,Da Tung Rd., Sec.3, Hsichih Dist., New Taipei City 221,TAIWAN

Global Certification Corp. Report No. : 0D0803 PHOTO OF EUT Appreance view of EUT Global Certification Corp. Report No. : 0D0803 PHOTO OF EUT Component Side of Main Board Solder Side of Main Board

Label location

Global Certification Corp. PHOTO OF EUT Open Case Global Certification Corp. Report No. : 0D0803 PHOTO OF EUT Component Side of Main Board Solder Side of Main Board Global Certification Corp. Report No. : 0D0803 PHOTO OF EUT Adaptor

FCC ID: WIJVVINWIFI Description of Operation AzureWave Technologies, Inc. introduces the pioneer of the IEEE 802.11b/g/n USB Half-Mini-Card wireless module ---AW-NU706H. The AW-NU706H USB Half-Mini-Card wireless module is a highly integrated wireless local area network (WLAN) solution to let users enjoy the digital content through the latest wireless technology without using the extra cables and cords. It enables a high performance, cost effective, low power, compact solution that easily fits onto one side of a USB Half-Mini-Card. Compliant with the IEEE 802.11b/g/n standard, the AW-NU706H uses Direct Sequence Spread Spectrum (DSSS), Orthogonal Frequency Division Multiplexing (OFDM), BPSK, QPSK, CCK and QAM baseband modulation technologies. A high level of integration and full implementation of the power management functions specified in the IEEE 802.11 standard minimize system power requirements by using AW-NU706H. Longer Range and Faster Speed Comparing to 802.11g technology, 802.11n draft 3.0 standard make big improvement on speed and range. It Increases wireless range by up to 2 times and reduces dead spots in coverage area. The data rate can up to 150Mbps data rate

Global Certification Corp. Date of Issue: Jan. 03, 2011 Report No:F0D0803 Page1/97 FCC 47 CFR PART 15 SUBPART C TEST REPORT FOR Product Name: IEEE 802.11b/g/n Half-Mini-Card Wireless Module Model : VVINWIFI Trade Name: VideoHome Issued to VideoHome Technology Corp. 4F-1,No.190/192,Da Tung Rd.,Sec.3,Hsichih Dist, New Taipei City 221,TAIWAN Issued by Global Certification Corp. EMC Test Site Sijhih Office and Lab No. 146, Sec. 2, Siangjhang Rd., Sijhih City, Taipei County 221, Taiwan (R.O.C.) Note: This test refers exclusively to the test presented test model and sample. This report shall not be reproduced except in full, without the written approval of Global Certification Corporation. This document may be altered or revised by Global Certification Corporation. Personnel only, and shall be noted in the revision section of the document. Global Certification Corp. Date of Issue: Jan. 03, 2011 Report No:F0D0803 Page2/97 TABLE OF CONTENTS ----------------------------------------------------------------------------------------------------- 2 1. GENERAL INFORMATION -------------------------------------------------------------------------------------------------------- 4 1.1 DESCRIPTION OF THE TESTED SAMPLES --------------------------------------------------------------------------------------------------- 5 2. TEST METHODOLOGY ------------------------------------------------------------------------------------------------------------- 7 2.1 GENERAL TEST PROCEDURES ------------------------------------------------------------------------------------------------------- 7 2.2 FCC PART 15.205 RESTRICTED BANDS OF OPERATIONS -------------------------------------------------------------------- 7 2.3 DESCRIPTION OF TEST MODES ------------------------------------------------------------------------------------------------------ 8 2.4 DESCRIPTION OF THE SUPPORT EQUIPMENTS -------------------------------------------------------------------------------- 9 3. TEST AND MEASUREMENT EQUIPMENT ----------------------------------------------------------------------------------- 10 3.1 CALIBRATION --------------------------------------------------------------------------------------------------------------------------- 10 3.2 EQUIPMENT ----------------------------------------------------------------------------------------------------------------------------- 10 4. ANTENNA REQUIREMENTS ----------------------------------------------------------------------------------------------------- 11 4.1 STANDARD APPLICABLE -------------------------------------------------------------------------------------------------------------- 11 4.2 ANTENNA CONSTRUCTION AND DIRECTIONAL GAIN ----------------------------------------------------------------------------- 11 5. PEAK POWER ------------------------------------------------------------------------------------------------------------------------- 12 5.1 TEST SETUP ---------------------------------------------------------------------------------------------------------------------------- 12 5.2 LIMIT ------------------------------------------------------------------------------------------------------------------------------------ 12 5.3 TEST PROCEDURE ----------------------------------------------------------------------------------------------------------------- 12 5.4 TEST RESULT ------------------------------------------------------------------------------------------------------------------------- 12 5.5 TEST DATA ----------------------------------------------------------------------------------------------------------------------------- 13 6. AVERAGE POWER ------------------------------------------------------------------------------------------------------------------ 14 6.1 TEST SETUP ---------------------------------------------------------------------------------------------------------------------------- 14 6.2 LIMIT ------------------------------------------------------------------------------------------------------------------------------------ 14 6.3 TEST PROCEDURE --------------------------------------------------------------------------------------------------------------------- 14 6.4 TEST RESULT ------------------------------------------------------------------------------------------------------------------------- 14 6.5 TEST DATA ----------------------------------------------------------------------------------------------------------------------------- 15 7. SECTION 15.247 REQUIREMENTS (HARMONICS) ------------------------------------------------------------------------ 16 7.1 TEST SETUP----------------------------------------------------------------------------------------------------------------------------- 16 7.2 LIMIT ------------------------------------------------------------------------------------------------------------------------------------ 16 7.3 RESULT -------------------------------------------------------------------------------------------------------------------------------- 16 7.4 TEST DATA ----------------------------------------------------------------------------------------------------------------------------- 17 8. SECTION 15.205 REQUIREMENTS (BAND EDGE) ------------------------------------------------------------------------- 30 8.1 TEST SETUP----------------------------------------------------------------------------------------------------------------------------- 30 8.2 LIMIT ------------------------------------------------------------------------------------------------------------------------------------ 30 8.3 RESULT -------------------------------------------------------------------------------------------------------------------------------- 30 8.4 TEST DATA ----------------------------------------------------------------------------------------------------------------------------- 31 9. SECTION 15.209 REQUIREMENTS (GENERAL RADIATED EMISSION) -------------------------------------------- 48 9.1 TEST SETUP------------------------…

Text truncated - open the document above for the full version.

Global Certification Corp. Appendix 1 PHOTOS OF TEST CONFIGURATION Global Certification Corp. Report No. : F0D0803 Radiated Emission