WWMMN527V1300Mbps Wireless N USB Module

PW-MN527 300Mbps Wireless N USB Module User Guide Version 1.0 July 31, 2012 PROWARE TECHNOLOGIES CO., Ltd. Copyright Notice: Copyright © 2012, PROWARE Technologies CO,. Ltd . All Rights Reserved. No part of this document may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise without the prior written permission of PROWARE Technologies CO,. Ltd is a registered trademark of PROWARE Technologies CO,. Ltd. All trademarks are the properties of their respective owners. Important: This product is only for Consumer Electronics device factory’s using. Terminal customers will not have direct access to buy and use this product. Revision History Release Date Revision Initials 1.0 2012-7-31 First release. FCC STATEMENT This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:  Reorient or relocate the receiving antenna.  Increase the separation between the equipment and receiver.  Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.  Consult the dealer or an experienced radio/ TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. FCC RF Radiation Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. This device is intended only for OEM integrators under the following conditions:  The antenna must be installed such that 20 cm is maintained between the antenna and users, and  The transmitter module may not be co-located with any other transmitter or antenna. As long as 2 conditions above are met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed IMPORTANT NOTE: In the event that these conditions can not be met (for example certain laptop configurations or co-location with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID can not be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC authorization. End Product Labeling This transmitter module is authorized only for use in device where the antenna may be installed such that 20 cm may be maintained between the antenna and users. The final end product must be labeled in a visible area with the following: “Contains FCC ID: WWMMN527V1 . The grantee's FCC ID can be used only when all FCC compliance requirements are met. Manual Information To the End User The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the user’s manual of the end product which integrates this module. CE Mark Warning This is a class B product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures. CONTENTS Package Contents .................................................................................................... 7 Chapter 1 Introduction ........................................................................................... 8 1.1 Overview of the Product ............................................................................................ 8 1.2 Features ..................................................................................................................... 8 Chapter 2 Installation Guide .................................................................................. 9 2.1 Hardware Installation ................................................................................................. 9 2.2 Software Installation .................................................................................................. 9 Chapter 3 Linux Installation Guide (For Consumer Electronics) ..................... 14 3.1 Hardware Installation ............................................................................................... 14 3.2 Software Installation ................................................................................................ 14 Appendix A: Specifications ................................................................................... 15 Appendix B: Glossary ............................................................................................ 16 PW-MN527 300Mbps Wireless N USB Module 7 Package Contents The following items should be found in your…

Text truncated - open the document above for the full version.

PROWARE TECHNOLOGIES CO., LTD. Attestation for FCC Declaration of Conformity FCC ID: WWMMN527V1 Date: 2012‐09‐05 Please be notified that we, the undersigned, Proware Technologies Co Ltd., LTD declare that the product bears the above FCC ID is also complying with the requirements of FCC DoC. The test report number for FCC DoC is FD120711C30, with is issued by an accredited lab, Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch (BV CPS Taoyuan) of Taiwan. Which has been accredited in accordance to all of the requirements of 47CFR 2.948(d) and (e) of the FCC rules and KDB349827. Sincerely, Name of authorized signer: Yongquan Wang Title of authorized signer: Product Dept. Manager Company Name: PROWARE Technologies Co., Ltd. Tel: 86-755-26502509 Fax: 86-755-26508930 Web site: WWW.PROWARE.COM.CN

FCC ID: WWMMN527V1 Report No.: RF120711C30 Modular Approval Request Letter Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch September 12, 2012 Dear Application Examiner, Proware Technologies Co., Ltd., It’s a 300Mbps Wireless N USB Module, FCC ID: WWMMN527V1 would like to have your authorization as a modular device. The requirements of section 15.212 of FCC rules have been met and shown on the following statements. 1. “The modular transmitter must have its own RF shielding.”: The radio portion of this module has been shielded, please see exhibition External Photo. 2. “The modular transmitter must have buffered modulation/data inputs.” The EUT has buffered data inputs, it is integrated in chip RT5372-QFN68-8X8. 3. “The modular transmitter must have its own power supply regulation.” The part number of this regulator is RT8020. 4. “The modular transmitter must comply with the antenna requirements of section 15.203 and 15.204(C).” The EUT meets the FCC antenna requirements. The spurious emission, unique antenna connector and photo of antennas are shown in the test report. 5. “The modular transmitter must be tested in a stand-alone configuration” The EUT was tested in a stand-alone configuration. Please see section Photographs of Test Configuration in the test report, the EUT was plugged in this extender. 6. “The modular transmitter must be labeled with its own FCC ID number.” Please see exhibition Label Sample for the FCC ID of this module. And also in the exhibition Users Manual, there are instructions give to the OEM on how to label the end product. FCC ID: WWMMN527V1 Report No.: RF120711C30 7. “The modular transmitter must comply with any specific rule or operating requirements applicable to the transmitter and the manufacturer must provide adequate instructions along with the module to explain any such requirements.” The EUT is compliant with all applicable FCC rules. Detail instructions for maintaining compliance are given in the Users Manual. 8. “The modular transmitter must comply with any applicable RF exposure requirements.” The EUT is compliant with all applicable RF exposure requirements. RF Exposure is addressed in the RF exposure exhibition. Please contact me if you have any further questions. Thanks for your attention. Best Regards, signature Gary Chang Technical Manager Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch

PROWARE TECHNOLOGIES CO., LTD. Date: 2012‐09‐05 FCC ID: WWMMN527V1 To the attention of Federal Communications Commission Authorization and Evaluation Division Confidentiality Request Pursuant to Sections 0.457 and 0.459 of the Commission’s Rules, the Applicant hereby requests confidential treatment of information accompanying this Application as outlined below: Schematics Block Diagram Operational Description The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the Applicant and provide unjustified benefits to its competitors. The Applicant understands that pursuant to Rule 0.457, disclosure of this Application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely yours, Name of authorized signer: Yongquan Wang Title of authorized signer: Product Dept. Manager Company Name: PROWARE Technologies Co., Ltd. Tel: 86-755-26502509 Fax: 86-755-26508930 Web site: WWW.PROWARE.COM.CN

PROWARE TECHNOLOGIES CO., LTD. Date: 2012‐09‐05 AUTHORIZATION LETTER To whom it may concern: We, the undersigned PROWARE Technologies Co., Ltd hereby authorize Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch (BV CPS Taoyuan) of Taiwan to act on our behalf in all matters relating to all processes required in FCC approval and any communication needed with the national authority. Any and all acts carried out by BV CPS Taoyuan on our behalf shall have the same effects as acts of our own. If you have any questions regarding the authorization, please don’t hesitate to contact us. Thank you! Sincerely yours, Name of authorized signer: Yongquan Wang Title of authorized signer: Product Dept. Manager Company Name: PROWARE Technologies Co., Ltd. Tel: 86-755-26502509 Fax: 86-755-26508930 Web site: WWW.PROWARE.COM.CN

Page 1 CONSTRUCTION PHOTOS OF EUT

Label location

C B A 12 C 345678 B E D D A 9 料号： 12345 E 6789 与上一版的区别 颜 色 名 称 版 本 材 质 模 具 机型版本号 logo 底色 文字 其它 结构工程师 硬件工程师 产品工程师 平面负责人 记 录 审 核 完成日期 设 计 PW-MN527彩印标贴 A1 80g艾利铜版纸+光膜 MU6 PW-MN527(MU6)1.0 林如君 2012.7.11 单色印刷 尺寸：14.05x15.15mm，0.5R 公差范围：长±0.2、宽±0.2mm 3倍放大文字转曲线 FCC IDWWMMN527V1 Wireless N USB Module PW-MN527 FCC IDWWMMN527V1

Page 1 CONSTRUCTION PHOTOS OF EUT

Report No.: SA120711C30 of 5 Report Format Version 5.0.0 1 RF EXPOSURE REPORT REPORT NO.: SA120711C30 MODEL NO.: PW-MN527 FCC ID: WWMMN527V1 RECEIVED: Jul. 11, 2012 TESTED: Aug. 27 ~ Sep. 05, 2012 ISSUED: Sep. 07, 2012 APPLICANT: Proware Technologies Co., Ltd. ADDRESS: 2nd F1 East Wing,South Section,Factory Building 24,Science&Technology Park, Shennan Rd, Nanshan District, Shenzhen ISSUED BY: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch LAB ADDRESS: No. 47, 14th Ling, Chia Pau Vil., Lin Kou Dist., New Taipei City, Taiwan, R.O.C. TEST LOCATION: No. 19, Hwa Ya 2nd Rd, Wen Hwa Tsuen, Kwei Shan Hsiang, Taoyuan Hsien 333, Taiwan, R.O.C. This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the compliance or non-com pliance to the specification. This report should not be used by the client to claim product certification, approval, or endorsement by any government agencies. Report No.: SA120711C30 of 5 Report Format Version 5.0.0 2 TABLE OF CONTENTS RELEASE CONTROL RECORD ................................................................................................ 3 1. CERTIFICATION ............................................................................................................. 4 2. RF EXPOSURE ............................................................................................................... 5 2.1 LIMITS FOR MAXIMUM PERMISSIBLE EXPOSURE (MPE) ......................................... 5 2.2 MPE CALCULATION FORMULA .................................................................................... 5 2.3 CLASSIFICATION ........................................................................................................... 5 2.4 CALCULATION RESULT OF MAXIMUM CONDUCTED POWER .................................. 5 Report No.: SA120711C30 of 5 Report Format Version 5.0.0 3 RELEASE CONTROL RECORD ISSUE NO. REASON FOR CHANGE DATE ISSUED SA120711C30 Original release Sep. 07, 2012 Report No.: SA120711C30 of 5 Report Format Version 5.0.0 4 1. CERTIFICATION PRODUCT: 300Mbps Wireless N USB Module MODEL: PW-MN527 BRAND: PROWARE APPLICANT: Proware Technologies Co., Ltd. TESTED: Aug. 27 ~ Sep. 05, 2012 TEST SAMPLE: PROTOTYPE STANDARDS: FCC Part 2 (Section 2.1091) FCC OET Bulletin 65, Supplement C (01-01) IEEE C95.1 The above equipment (Model: PW-MN527) has been tested by Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch, and found compliance with the requirement of the above standards. The test record, data evaluation & Equipment Under Test (EUT) configurations represented herein are true and accurate accounts of the measurements of the sample’s EMC characteristics under the conditions specified in this report. PREPARED BY : , DATE :Sep. 07, 2012 Joanna Wang / Supervisor APPROVED BY : , DATE :Sep. 07, 2012 Gary Chang / Technical Manager Report No.: SA120711C30 of 5 Report Format Version 5.0.0 5 2. RF EXPOSURE 2.1 LIMITS FOR MAXIMUM PERMISSIBLE EXPOSURE (MPE) FREQUENCY RANGE (MHz) ELECTRIC FIELD STRENGTH (V/m) MAGNETIC FIELD STRENGTH (A/m) POWER DENSITY (mW/cm 2 ) AVERAGE TIME (minutes) LIMITS FOR GENERAL POPULATION / UNCONTROLLED EXPOSURE 300-1500 ... ... F/1500 30 1500-100,000 ... ... 1.0 30 F = Frequency in MHz 2.2 MPE CALCULATION FORMULA Pd = (Pout*G) / (4*pi*r2) where Pd = power density in mW/cm2 Pout = output power to antenna in mW G = gain of antenna in linear scale Pi = 3.1416 R = distance between observation point and center of the radiator in cm 2.3 CLASSIFICATION The antenna of this product, under normal use condition, is at least 20cm away from the body of the user. So, this device is classified as Mobile Device. 2.4 CALCULATION RESULT OF MAXIMUM CONDUCTED POWER MAX POWER (dBm) ANTENNA GAIN (dBi) DISTANCE (cm) POWER DENSITY (mW/cm 2 ) LIMIT (mW/cm 2 ) 28.35 1.8 20 0.206 1

Report No.: RF120711C30 1 of 55 Report Format Version 5.0.0 FCC TEST REPORT REPORT NO.: RF120711C30 MODEL NO.: PW-MN527 FCC ID: WWMMN527V1 RECEIVED: Jul. 11, 2012 TESTED: Aug. 27 ~ Sep. 05, 2012 ISSUED: Sep. 07, 2012 APPLICANT: Proware Technologies Co., Ltd. ADDRESS: 2nd F1 East Wing,South Section,Factory Building 24,Science&Technology Park, Shennan Rd, Nanshan District, Shenzhen ISSUED BY: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch LAB ADDRESS: No. 47, 14th Ling, Chia Pau Vil., Lin Kou Dist., New Taipei City, Taiwan, R.O.C. TEST LOCATION: No. 19, Hwa Ya 2nd Rd, Wen Hwa Tsuen, Kwei Shan Hsiang, Taoyuan Hsien 333, Taiwan, R.O.C. This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the com pliance or non-compliance to the specification. This report should not be used by the client to claim product certification, approval, or endorsement by TAF or any government agencies. Report No.: RF120711C30 2 of 55 Report Format Version 5.0.0 TABLE OF CONTENTS RELEASE CONTROL RECORD ............................................................................................................ 4 1. CERTIFICATION ......................................................................................................................... 5 2. SUMMARY OF TEST RESULTS ................................................................................................ 6 2.1 MEASUREMENT UNCERTAINTY .............................................................................................. 6 3. GENERAL INFORMATION ......................................................................................................... 7 3.1 GENERAL DESCRIPTION OF EUT ........................................................................................... 7 3.2 DESCRIPTION OF TEST MODES ............................................................................................. 8 3.2.1 TEST MODE APPLICABILITY AND TESTED CHANNEL DETAIL ............................................. 9 3.3 DESCRIPTION OF SUPPORT UNITS ..................................................................................... 11 3.3.1 CONFIGURATION OF SYSTEM UNDER TEST ...................................................................... 11 3.4 GENERAL DESCRIPTION OF APPLIED STANDARDS .......................................................... 12 4. TEST TYPES AND RESULTS .................................................................................................. 13 4.1 RADIATED EMISSION AND BANDEDGE MEASUREMENT .................................................. 13 4.1.1 LIMITS OF RADIATED EMISSION AND BANDEDGE MEASUREMENT ................................ 13 4.1.2 TEST INSTRUMENTS .............................................................................................................. 14 4.1.3 TEST PROCEDURES .............................................................................................................. 15 4.1.4 DEVIATION FROM TEST STANDARD .................................................................................... 15 4.1.5 TEST SETUP ............................................................................................................................ 16 4.1.6 EUT OPERATING CONDITIONS ............................................................................................. 16 4.1.7 TEST RESULT .......................................................................................................................... 17 4.2 CONDUCTED EMISSION MEASUREMENT ........................................................................... 30 4.2.1 LIMITS OF CONDUCTED EMISSION MEASUREMENT ........................................................ 30 4.2.2 TEST INSTRUMENTS .............................................................................................................. 30 4.2.3 TEST PROCEDURES .............................................................................................................. 31 4.2.4 DEVIATION FROM TEST STANDARD .................................................................................... 31 4.2.5 TEST SETUP ............................................................................................................................ 31 4.2.6 EUT OPERATING CONDITIONS ............................................................................................. 31 4.2.7 TEST RESULTS ....................................................................................................................... 32 4.3 6dB BANDWIDTH MEASUREMENT ........................................................................................ 34 4.3.1 LIMITS OF 6dB BANDWIDTH MEASUREMENT ..................................................................... 34 4.3.2 TEST SETUP ...........................................................................…

Text truncated - open the document above for the full version.

1 PHOTOGRAPHS OF THE TEST CONFIGURATION CONDUCTED EMISSION TEST 2 3 RADIATED EMISSION TEST 4