WZ6-69547INDUCTION

Operator’s Manual Item No. 23462-1 en Rev 01/11 ENGLISH FOODSERVICE INDUCTION RANGES Thank you for purchasing this Vollrath Induction Range. Before operating the unit, read and familiarize yourself with the following operating and safety instructions. SAVE THE ORIGINAL BOX AND PACKAGING. Use this packaging to ship the unit if repairs are needed. SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE. ModelDescriptionVoltageHZkWPlug 69504Countertop – Single208 - 24050/603.0 - 3.56-20P 69505Drop-in – Single208 - 24050/603.0 - 3.56-20P 69507Countertop – Dual, Front-to-Back208 - 24050/603.0 - 3.56-50P 69508Drop-in – Dual, Front-to-Back208 - 24050/603.0 - 3.56-50P 69520Countertop – Single208 - 24050/602.5 -2.96-20P 69521Drop-in – Single208 - 24050/602.5 - 2.96-20P 69523Countertop – Dual, Side By Side208 - 24050/602.5 - 2.96-30P 69522Countertop – Dual, Front-to-Back 208 - 24050/602.5 - 2.96-20P 69524Drop-in – Dual, Front-to-Back 208 - 24050/602.5 - 2.96-30P 69547Countertop – Dual, Front-to-Back 208 - 24050/603.3 - 3.86-20P 6954301Countertop – Single208 - 24050/602.2 - 2.66-20P 6954302Countertop – Single208 - 24050/602.2 - 2.6Schuko 6954303Countertop – Single208 - 24050/602.2 - 2.6UK 6954701Countertop – Dual, Front-to-Back 208 - 24050/603.3 - 3.86-20P 6954702Countertop – Dual, Front-to-Back208 - 24050/603.3 - 3.8Schuko 6954703Countertop – Dual, Front-to-Back208 - 24050/603.3 - 3.8UK Foodservice induction ranges OperatOr’s Manual 2 Safety PrecautionS To ensure safe operation, read the following statements and understand their meaning. This manual contains safety precautions which are explained below. Please read carefully. WARNING Warning is used to indicate the presence of a hazard that can cause severe personal injury, death, or substantial property damage if the warning is ignored. CAUTION Caution is used to indicate the presence of a hazard that will or can cause minor personal injury or property damage if the caution is ignored. NOTE Note is used to notify people of installation, operation, or maintenance information that is important but not hazard-related. For Your Safety! These precautions should be followed at all times. Failure to follow these precautions could result in injury to yourself and others. To reduce risk of injury or damage to the unit: „Plug only into grounded electrical outlets matching the nameplate rated voltage. „Do not use an extension cord with this equipment. Do not plug this equipment into a power strip or multi-outlet power cord. „As a precaution, persons using a pacemaker should stand back 12” (30 cm) from an operating unit. Studies have shown that the induction element will not disrupt a pacemaker. „Keep all credit cards, driver liscences and other items with a magnetic strip away from an operating unit. The unit’s magnetic field will damage the information on these strips. „The heating surface is made of a strong, non-porous material. However, should it crack or break, stop using and immediately unplug the unit. „Do not leave an empty pan on an operating unit. „Unit should only be used in a flat, level position. „Unplug unit and let it cool before cleaning or moving. „Do not touch the cooking surface. It remains hot after the unit is turned off. „Do not spray controls or outside of unit with liquids or cleaning agents. „Unplug when not in use. „Keep unit and power cord away from open flames, electric burners or excessive heat. „Do not heat sealed cans or containers as they may explode. „Do not operate unattended. Closely supervise units operating in public areas and/or around children. „Do not operate if unit has been damaged or is malfunctioning in any way. „Do not place any objects inside the air intake or exhaust panels. „Do not place weight on the control knob. function and PurPoSe This unit is intended to be used with induction-ready cookware (see below) with a flat, ferrous base measuring 4-1/2” (11.4 cm) to 10-1/4” (26 cm) wide. This unit is intended for use in commercial foodservice operations only. It is not intended for household, industrial or laboratory use. induction ready cookware „Ferrous stainless steel „Iron „Cast iron unsuitable cookware „Cookware with a base less than 4-1/2” (11.4 cm) „Pottery, glass, aluminum, bronze or copper cookware „Cookware with any type of footed base This unit is to be used on a flat, level surface. The unit is not designed to be enclosed or built into any area. NOTE: There must be a minimum of 4” (10 cm) between the induction range and any surrounding surface to allow sufficient airflow around the unit. Blocking the airflow could overheat the unit inStallation coutertop 1. Place the induction range/warmer on a flat stable surface. NOTE: This unit is not designed to be inclosed or built into any area. There must be a minimum of 4” (10 cm) of space between the rear of the induction warmer and any surrounding surface. There must be 3/4” (2 cm) between the bottom of the induction warmer and any surrounding surface. Sufficient airflow must be allowed around the unit. Blocking the airflow could cause the unit to overheat. 2. Plug the power cord into a grounded electrical outlet with the matching nameplate rated voltage. NOTE: Using a voltage other than the nameplate rated voltage will cause damage to the unit. Incorrect voltage, modification to the power cord or electrical components can damage unit and will void the warranty. Induction units are to use a separate dedicated circuit. Foodservice induction ranges 3 ENGLISH OperatOr’s Manual drop-in 1. Choose a flat, level countertop for the mounting surface. NOTE: There must be a minimum of 3” (7.6 cm) of space between the rear of the induction warmer and any surrounding surface. There must be 1” (2.5 cm) between the bottom of the induction warmer and any surrounding surface. Sufficient airflow must be allowed around the unit. Blocking the airflow could cause the unit to overheat. 2. Measure the area for the cutout, including the countersink area. The unit is designed to be countersun…

Text truncated - open the document above for the full version.

Report No.: TB-FCC108252 Page: 3 of 6 TB-RF-075-1.0 Appendix III EUT External Photographs Photo 1 Appearance of EUT Photo 2 Appearance of EUT

Report No.: TB-FCC108252 Page: 2 of 6 TB-RF-075-1.0 Appendix II ID Label Location FCC ID LOCATION

Report No.: TB-FCC108252 Page: 1 of 6 TB-RF-074-1.0 Appendix IID Label

Report No.: TB-FCC108252 Page: 4 of 6 TB-RF-075-1.0 Appendix IV EUT Internal Photographs Photo 3 Inside of EUT Photo 4 Inside of EUT Report No.: TB-FCC108252 Page: 5 of 6 TB-RF-075-1.0 Photo 5 Appearance of PCB Photo 6 Appearance of PCB

2500 Circuit Description 1.2500 is the main board of 69547. It contains a microchip which style is AT89S52,the Y1 is generated the 11.0592MHz clock signal to it. 2.69647 include 2500 main board, 0310 display board, and 1901 EMI board. Display board and IGBT controlled by main board.

ABCD DCBA Title Number Revision Size A3 Date: 25-Dec-2008 Sheet of File: C:\PROGRAM FILES\DESIGN EXPLORER 99 SE\EXAMPLES\display1.DDB Drawn By: A 7 B 6 C 4 D 2 E 1 F 9 G 10 DP 5 CA 3 CA 8 UL1 LDSA512RI A 7 B 6 C 4 D 2 E 1 F 9 G 10 DP 5 CA 3 CA 8 UM1 LDSA512RI A 7 B 6 C 4 D 2 E 1 F 9 G 10 DP 5 CA 3 CA 8 UH1 LDSA512RI STR 1 D 2 CLK 3 OE 15 Q1 4 Q2 5 Q3 6 Q4 7 Q5 14 Q6 13 Q7 12 Q8 11 QS 9 QS 10 VCC 16 GND 8 U12 4094 STR 1 D 2 CLK 3 OE 15 Q1 4 Q2 5 Q3 6 Q4 7 Q5 14 Q6 13 Q7 12 Q8 11 QS 9 QS 10 VCC 16 GND 8 U13 4094 STR 1 D 2 CLK 3 OE 15 Q1 4 Q2 5 Q3 6 Q4 7 Q5 14 Q6 13 Q7 12 Q8 11 QS 9 QS 10 VCC 16 GND 8 U11 4094 C120.1uFC110.1uF C130.1uF R10150/1W 123456789 1011121314 J1114PIN LEDB3 DS2 LEDB7LEDB6LEDB5LEDB4LEDB2LEDB1LEDB0 LEDC7LEDC6LEDC5LEDC4LEDC3LEDC2LEDC1LEDC0LEDB7LEDB6LEDB5LEDB4LEDB3LEDB2LEDB1LEDB0 LEDA7LEDA6LEDA5LEDA4LEDA2LEDA1LEDA0 LEDA7LEDA6LEDA5LEDA4LEDA3LEDA2LEDA1LEDA0 DISPDISPDISPDATACLKCLKCLK DS1 DS1DS2DISPDISPDISP DISP=H: DISPLAY ONDISP=L: DISPLAY OFF LED 7-Segment DispDigi No.: 67-1423-NDColor: RedCommon AnodeLUMEX: LDT-A514RI KDOWNKUPKONOFDISPDATACLKKNOBKTIMEKT/PLEDGNDGND LEDC5LEDC4LEDC2LEDC1LEDC0LEDC6LEDC7 +5V +5V+5V+5V +5V STR 1 D 2 CLK 3 OE 15 Q1 4 Q2 5 Q3 6 Q4 7 Q5 14 Q6 13 Q7 12 Q8 11 QS 9 QS 10 VCC 16 GND 8 U22 4094 STR 1 D 2 CLK 3 OE 15 Q1 4 Q2 5 Q3 6 Q4 7 Q5 14 Q6 13 Q7 12 Q8 11 QS 9 QS 10 VCC 16 GND 8 U23 4094 STR 1 D 2 CLK 3 OE 15 Q1 4 Q2 5 Q3 6 Q4 7 Q5 14 Q6 13 Q7 12 Q8 11 QS 9 QS 10 VCC 16 GND 8 U21 4094 C220.1uFC210.1uFC230.1uF DS5LEDF7LEDF6LEDF5LEDF4LEDF3LEDF2LEDF1LEDF0LEDE7LEDE6LEDE5LEDE4LEDE3LEDE2LEDE1LEDE0LEDD7LEDD6LEDD5LEDD4LEDD3LEDD2LEDD1LEDD0 KNOBKNOBKNOBCLKCLKCLK DS4 DS4DS5KNOBKNOBKNOB +5V+5V+5V DS3 DS3 A 7 B 6 C 4 D 2 E 1 F 9 G 10 DP 5 CA 3 CA 8 UL2 LDSA512RI A 7 B 6 C 4 D 2 E 1 F 9 G 10 DP 5 CA 3 CA 8 UM2 LDSA512RI A 7 B 6 C 4 D 2 E 1 F 9 G 10 DP 5 CA 3 CA 8 UH2 LDSA512RI R20150/1W LEDE3LEDE7LEDE6LEDE5LEDE4LEDE2LEDE1LEDE0LEDD7LEDD6LEDD5LEDD4LEDD2LEDD1LEDD0LEDF5LEDF4LEDF2LEDF1LEDF0LEDF6LEDF7 +5V R11560 LED11On/Off-Green LED LED12Power_Green R12560 +5V KT/P_OUT KTIME_OUT KDOWN_OUT KUP_OUT KONOF_OUT KT/P_OUT KTIME_OUT KDOWN_OUT KONOF_OUT KDOWN KUP KONOFKTIMEKT/P 1 2 3 4 S11 1 2 3 4 S12 1 2 3 4 S13 1 2 3 4 S14 1 2 3 4 S15 KT/P_OUT KTIME_OUT KDOWN_OUT KUP_OUT KONOF_OUT 1 2 3 4 S21 1 2 3 4 S22 1 2 3 4 S23 1 2 3 4 S24 1 2 3 4 S25 69-0310 key board LED14TempC-Red R141K LED13TempF-Red R131K R21560 LED21On/Off-Green LED22Power_Green R22560 +5V LED24TempC-Red R241K LED23TempF-Red R231K STR 1 D 2 CLK 3 OE 15 Q1 4 Q2 5 Q3 6 Q4 7 Q5 14 Q6 13 Q7 12 Q8 11 QS 9 QS 10 VCC 16 GND 8 U15 4094 C150.1uF +5V STR 1 D 2 CLK 3 OE 15 Q1 4 Q2 5 Q3 6 Q4 7 Q5 14 Q6 13 Q7 12 Q8 11 QS 9 QS 10 VCC 16 GND 8 U14 4094 C140.1uF LEDG7LEDG6LEDG5LEDG4LEDG3LEDG2LEDG1LEDG0 CLKDS6LED +5V DS6 LEDD3LEDF3 LEDC3LEDA3 LEDG7 LEDG6 LEDG5 LEDG4 LEDG3 LEDG2 LEDG1 LEDG0 KONOF 21 3 D11BAV70 KUP_OUT 21 3 D12BAV70 21 3 D13BAV70 21 3 D14BAV70 21 3 D15BAV70
/;'/  
  
  
   

 
 

   

      
 
 
    
      
         
 
    
!      
    !                                       
    
 
      
 

 
  
 !" #
 !"
$##
 !"#
 !"#  %   & &' 
  & &' 
%  & &' 
%  
 & &' 

  
% &% &' 


  


&
 &' 



 
   
    
    
   
  

 &
(
 &
 (
   
 
!
#)*
!
%+*,            
-    -    %.%. .
.
%.


.
./0 ./0 
 # 
 #
!
#)*
!
+*,   
  
 &
 (
 &
(

!   
1 
1 '++   1 #

/;'/              
         
 
   

 
    


    
  !   
       

  !
  
   
   "#  
$   "#  
$   
 ! %  &% ' #
( ' #
(  '   
(      
      
    )!

    )
!



  %
 % * *
 *

*
*
 *

*
 

       "#  
$  
 "#  
$    

             * * (  (
*  %    
 

+ (  
+ (  
+( ( 
+ ( (  ,  # '



( '


( -

#
(  
 

 -
,
( -,
( -

#
(  *  *
  *
 
*

  *
  *   * 
 
(
     

 

   * 
+!.!(% 
+!.!(* 
+!.(!!%. 
+!.(!!*    
  *    
 * * 
  (    
(      

' * 

    
 




   (   

(       
 ' * 

    
 

 
   
(        

' * 

    

 

 
+
( /01234 *
  +'% 
+'% 
+
 /56"2 *
 *
 
+


/56"2       7
(

/;'/      
                   !  "#
$%  &  &  &
' &  &  &'
&  & &  & ( )"" ' *+! , "!( ' 
-. /  . /  '( / 
-. /   -. / 
((. / ( (. / 
 . / 

'. / 
 . / "( '(01 "( 1 " ( 1 
'
. / "'…

Text truncated - open the document above for the full version.

Shenzhen Toby Technology Co., Ltd. Report No.: TB-FCC108252 Page: 1 of 14 TB-RF-074-1.0 10/F., A Block, Jiada R & D Bldg., No.5 Songpingshan Road, Science & Technology Park, Nanshan District, Shenzhen, China Tel: +86 75526509301 Fax: +86 75526509195 FCC Test Report FCC ID: WZ6-69547 Report No. : TB-FCC108252 Applicant : Luxine (Xi’an) Electronics Co., Ltd. Equipment Under Test (EUT) EUT Name : Induction Cooker Model No. : 69547 Serial No. : 6954701, 6954702, 6954703 Brand Name : VOLLRATH Receipt Date : 2010-12-20 Test Date : 2010-12-21 to 2011-01-06 Issue Date : 2011-01-07 Standards : FCC Part 18 : 2008 Method : FCC OST/MP-5:1986 Conclusions : PASS In the configuration tested, the EUT complied with the standards specified above, The EUT technically complies with the FCC requirements Test/Witness Engineer Ray Lai (Engineer) : Approved& Authorized Justin Zhang (Manager) : This report details the results of the testing carried out on one sample. The results contained in this test report do not relate to other samples of the same product. The manufacturer should ensure that all products in series production are in conformity with the product sample detailed in the report. Report No.: TB-FCC108252 Page: 2 of 14 TB-RF-074-1.0 Contents CONTENTS.............................................................................................................................................2 1. GENERAL INFORMATION ABOUT EUT.............................................................................3 1.1 Client Information.................................................................................................................3 1.2 General Description of EUT (Equipment Under Test)...................................................3 1.3 Block Diagram Showing the Configuration of System Tested......................................4 1.4 Description of Support Units..............................................................................................4 1.5 Description of Test Mode....................................................................................................4 1.6 Test Location........................................................................................................................5 2. TEST SUMMARY.......................................................................................................................6 3. CONDUCTED EMISSION TEST.............................................................................................7 3.1 Test Standard and Limit......................................................................................................7 3.2 Test Setup.............................................................................................................................7 3.3 Test Procedure.....................................................................................................................7 3.4 Deviation...............................................................................................................................8 3.5 Test Equipment Used..........................................................................................................8 3.5 Test Data...............................................................................................................................8 4. RADIATED EMISSION TEST................................................................................................11 4.1 Test Standard and Limit....................................................................................................11 4.2 Test Setup...........................................................................................................................11 4.3 Test Procedure...................................................................................................................11 4.4 Deviation.............................................................................................................................11 4.5 Test Equipment..................................................................................................................12 4.6 Test Condition....................................................................................................................12 Report No.: TB-FCC108252 Page: 3 of 14 TB-RF-074-1.0 1. General Information About EUT 1.1 Client Information Applicant : Luxine (Xi’an) Electronics Co., Ltd. Address : 4th Floor, Building B, Seeker Industrial Park, 2nd JinYe Rd, Hi-tech Development Zone, Xi’an, China Manufacturer : Luxine (Xi’an) Electronics Co., Ltd. Address : 4th Floor, Building B, Seeker Industrial Park, 2nd JinYe Rd, Hi-tech Development Zone, Xi’an, China 1.2 General Description of EUT (Equipment Under Test) EUT Name : Induction Cooker Model No. : 69547 Serial No. : 6954701, 6954702, 6954703 Model difference : The only difference is the plug of the power line. Power Supply : AC 240V, 60Hz Power : 3800W (The big coil is 2000W, the small coil is 1800W) Connecting I/O Port(s) : Please refer to the User's Manual Note: For a more detailed features description, please refer to the manufacturer’s specifications or the User’s Manual. Report No.: TB-FCC108252 Page: 4 of 14 TB-RF-074-1.0 1.3 Block Diagram Showing the Configuration of System Tested 1.4 Description of Support Units The EUT has been tested with water up to 80% of the maximum capacity of the boiler. 1.5 Description of Test Mode To investigate the maximum EMI emission characteristics generates from EUT, the test system was pre-scanning tested base on the consideration of the EUT operation mode, and the worst Case is when the EUT is operation with the maximum power, so the conducted and radiated emission data of bellow only showed the worst case. LISN AC Power Receiver Conducted Emission Test Radiated Emission Test AC Power Report No.: TB-FCC108252 Page: 5 of 14 TB-RF-074-1.0 1.6 Test Location This test was performed at: Shenzhen Huatongwei International Inspection Co., Ltd.…

Text truncated - open the document above for the full version.

Report No.: TB-FCC108252 Page: 6 of 6 TB-RF-075-1.0 Appendix V EUT Test Photographs Photo of Setup for Radiated Emission Photo of Setup for Conducted Emission