X26SAS-1Audio streamer for hearing instruments with wireless capabilities

1 USER GUIDE 23 Statement: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must ac- cept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable pro- tection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communi- cations. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful inter- ference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Welcome Congratulations on your purchase of a ReSound Unite TV. ReSound Unite TV will provide you with high quality streamed audio from your TV, HiFi stereo, personal computer or similar device directly to your hearing instruments. Please read this manual carefully to fully benefit from the ReSound Unite TV. Ask your hearing care professional if you have any questions. For further information you can also visit the www.resound.com/unite web site. For your safety, carefully read the chapter Important Information, on pages 24-25 FCC ID: X26 SAS-1 45 These products are intended for world wide sales , and in compli- ance with the following regulatory standards: In EU: The device conforms to the Essential Requirements ac- cording to - Annex I of Council Directive 93/42/EEC for medical devices (MDD) and essential requirements and other relevant pro- visions of Directive 1999/5/EC (R&T TE).The declaration of confor- mity may be consulted at www.resound.com Annex I of Directive 2006/95/EC Low Voltage Directive (LVD) In US: All test objects are subject to FCC Certification according to FCC CFR 47 Part 15, subpart C, section 15.247 For the Norwegian market the accessories comply to EN 12182 Technical Aids for disabled persons. General requirements and test methods covered by EMC and electrical safety tests according to EN/IEC 60601-1-2 and EN/IEC 60950. Other identified applicable international regulatory requirements in countries outside EU and US. Please refer to local country requirements for these areas. Products are categorized as receiver class 2 according to Directive 1999/5/EEC on Radio Equipment and Telecommunica- tions Terminal Equipment (R&T TE) t
3FPSJFOU
PS
SFMPDBUF
UIF
SFDFJWJOH
BOUFOOB t
*ODSFBTF
UIF
TFQBSBUJPO
CFUXFFO
UIF
FRVJQNFOU
BOE
SFDFJWFS
t
$POOFDU
UIF
FRVJQNFOU
JOUP
BO
PVUMFU
PO
B
DJSDVJU
EJGGFSFOU
from the receiver is connected. t
$POTVMU
UIF
EFBMFS
PS
BO
FYQFSJFODFE
SBEJP57
UFDIOJDJBO
GPS
help. NOTE: All tests have been performed at a FCC listed lab (DELTA, Venlighedsvej 4, Hørsholm, Denmark) Intended use The Resound Unite TV is intended to transfer signals from a TV set or other audio device to a ReSound wireless hearing instru- ment in order to enable the hearing impaired person to better follow TV or other audio programs. List of countries Products are intended for sale in countries within European Eco- nomic Area as well as Switzerland. In addition products are in- tended for world wide sales. 67 Contents Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-9 Getting Started..................................10-17 Pairing to your hearing instruments..................18-19 Start and stop streaming .........................20-22 Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23-24 Important Information............................24-25 Technical specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26 Warranty.........................................26 Troubleshooting guide ...........................28-35 Notes ...........................................36 89 6 Increase volume 7 Decrease volume 8 Channel indicator 9 Power light (green) 10 Activity light (amber) 11 Wall plug 12 Mini-USB plug Description 1 Mono / Stereo control 2 Left Audio connector 3 Right Audio connector 4 Mini-USB connector 5 Pairing button 12 11 8 1 2 4 5 3 9 10 6 7 1011 some TVs you can adjust the balance between the AUDIO OUT and the speakers – consult your TV manual for instructions. Getting Started Installing ReSound Unite TV Depending on your TV, HiFi stereo, Computer or other audio set- up, the installation for ReSound Unite TV may differ. The following steps will guide you through the pairing and connecting process, which can be easily accomplished by almost anyone. Start with connecting the cables and finish by pairing ReSound Unite TV to your hearing instruments. Connect audio cables to ReSound Unite TV. For TV, HiFi Stereo and Computer 1. Connect the power supply to the wall socket and insert the cable to the Mini-USB socket on ReSound Unite TV 2. Connect the red and white plug of the audio cord into the red and white plugs on ReSound Unite TV 3. Plug the other end of the red and white audio cord in the ”AUDIO OUT” terminal on the TV 4. The ”AUDIO OUT” is usually marked ”L – R” for left and right, and ”AUDIO OUT” and can be found on the back of the TV. Alternatively you can plug this cable into your HiFi Stereo. Note: With this installation, most TVs will send sound to both hearing instruments and speakers simultaneously. On 1213 3. Connect the Jack adapter on the other end of the audio cable 4. Plug the Jack adapter into the TVs ”HEADPHONE” output terminal, or alternatively in your computers’ audio terminal. In the packaging box you will find screws for mounting the streamer on a wall. Instead of using screws, …

Text truncated - open the document above for the full version.

April 13 2010 FCC ID: X26SAS-1 MPE calculation The transmitter operates at 2.4 GHz. The limit for §1.1310 for the general public is a maximum power density of 1 mW/cm 2 . The maximum measured conducted output power is 15.18 dBm or 33.0 mW. The gain of the antenna is 1.8 dBi = 1.5. The device is mobile and will be used at a separation distance greater than 20 cm. The maximum power density at a distance of 20 cm from the device is calculated according to equation 3, p. 19 of FCC OET Bulletin 65: € S= PG 4πR 2 = 0.033⋅1.5 4⋅π⋅20 2 =0.010mW/cm 2 Result: The estimated maximum power density is 0.010 mW/cm 2 , which is below the MPE limit of 1 mW/cm 2 . On behalf of GN Hearing A/S Claus Rømer Andersen DELTA

Xiamen.China 1.80 0,55 1,90 5,65 1,90 5,65 0,55 1,80 2,50 5,00 7,00 0,80 0,90 0,70 2,60 6,22 13,30 13,30 14,90 42,30 29,10 49,50 45,96 4,00 20,60 24,00 2,50 33,50 Rev.CHG.#DescriptionDateDesignChecked 05--Update height of letters24.02.2010JZHENGBVA 06-- Update notes: define the color of letters 02.03.2010JZHENGBVA 07-- Update letters of FCC & FCC ID 12.04.2010JZHENGBVA Notes: Pad print color: 1. The color for letters on side A is Grey (Pantone 422 light grey). 2. The color for letters on side B is Black (Pantone Process Black). SAS BOT COVER, PTD, 172894007 Name:Drawing Number:Revision:
#
$
#0.100.1Material:--Checked:BVASheet:1 of 1Units: mm. Angular:Linear:Symetric:Status:DevelopmentDate:12.04.2010Scale:2:1 Unless otherwise specifiedDesign:JZHENGProjectionDRW. size:A3 Side B Side A This item will be used in electric or electronic equipment. The supplier warrants and represents that the item is, and at all times will be, in compliance with international regulations regarding substances with environmental impact, including but not limited to the RoHS Directive 2002/95 of the European parliament and of the Council. M S P L R

Document Title: Doc. #: Rev. #: Internal photos of SAS-1 197990 A Form 0007380 - Rev I Short term confidential Page 1 of 2 Corp Template Not subject to issue control when printed Printed Date: 8 April 2010 Lautrupbjerg 7 P.O. Box 130 DK-2750 Ballerup Denmark Owner/Editor: Local Address, if applicable: Jesper Peitersen Date: 08.04.2010 Description according to item number 17180900. Electronics assembly front Electronics assembly back Document Title: Doc. #: Rev. #: Internal photos of SAS-1 197990 A Form 0007380 - Rev I Short term confidential Page 2 of 2 Corp Template Not subject to issue control when printed Printed Date: 8 April 2010 Electronics assembly with mechanics

DELTA Venlighedsvej 4 2970 Hørsholm Denmark Tel. +45 72 19 40 00 Fax +45 72 19 40 01 www.delta.dk VAT No. 12275110 DELTA Test Report TEST Reg. no. 19 The report must not be reproduced, except in full, without the written approval of DELTA. This report is issued under the rules of SWEDAC (Swedish Accreditation) and ILAC (Interna- tional Laboratory Accreditation Cooperation) including its MRA (Mutual Recognition Arrange- ment). Further information can be found at www.swedac.se and www.ilac.org. The report must not be reproduced, except in full, without the written approval of DELTA. This report is issued under the rules of DANAK (Danish Accreditation) and ILAC (International Laboratory Accreditation Cooperation) including its MRA (Mutual Recognition Arrangement). Further information can be found at www.danak.dk and www.ilac.org. The report must not be reproduced, except in full, without the written approval of DELTA. EMC_RepGen MAIN TEMPLATE V.45 / 2010-03-08 Radio parameter test of SAS-1 Performed for GN Hearing A/S DANAK-1910853, Rev. B Project no.: A506404-1 Page 1 of 56 14 April 2010 DANAK-1910853, Rev. B DELTA-A506404-1 Page 2 of 56 JAS/BLJ Title Radio parameter test of SAS-1 Test object SAS-1 Report no. DANAK-1910853, Rev. B Project no. A506404-1 Test period 22 December 2009 to 13 April 2010 Client GN Hearing A/S Lautrupbjerg 7 2750 Ballerup Denmark Tel.: +45 45 75 11 11 Contact person Vinnie Nørager E-mail: [email protected] Manufacturer GN Hearing A/S Specifications FCC CFR 47 Part 15, Subpart C Results The test objects were found to be in compliance with the specifications, as listed in Section 1 Test personnel Claus Momme Thomsen Henrik Egeberg Nielsen Jan Askov DANAK-1910853, Rev. B DELTA-A506404-1 Page 3 of 56 JAS/BLJ Date 14 April 2010 Project Manager Jan Askov Senior Specialist, Wireless DELTA Responsible Claus Rømer Andersen Team Manager, Wireless DELTA This report is a revision of the test report A506404-1 Rev. A dated 13 April 2010. The revision has been made due to the following: Units corrected on page 32, 34 and 36 (dBμV changed to dBμV/m). Instrument list revised to include calibration date and calibration interval. DANAK-1910853, Rev. B DELTA-A506404-1 Page 4 of 56 JAS/BLJ Table of contents Page 1. Summary of tests 5 2. Test objects 6 2.1 Test objects 6 2.2 Auxiliary equipment 7 3. General test conditions 8 3.1 Test setup during test 8 3.2 Description of radio link 9 3.3 Test sequence 10 4. Test results 11 4.1 Antenna requirement 11 4.2 Measurement of radio frequency voltage on mains 13 4.3 Measurement of radiated emission, 0.009-30 MHz 16 4.4 Measurement of radiated emission, 30 MHz to 1000 MHz 21 4.5 Measurement of radiated emission, 1 GHz to 25 GHz 31 4.6 Measurement of the 6 dB bandwidth 38 4.7 Measurement of conducted power output 42 4.8 Measurement of conducted spurious emissions 46 4.9 Measurement of power spectral density 50 5. National registrations and accreditations 54 5.1 DANAK Accreditation 54 5.2 FCC Registrations 54 5.3 VCCI Registrations 55 5.4 IC Registrations 55 6. List of instruments 56 DANAK-1910853, Rev. B DELTA-A506404-1 Page 5 of 56 JAS/BLJ 1. Summary of tests Tests Test methods Rule Section Results Antenna requirement Visual inspection 15.203 Passed Radio frequency voltage on mains ANSI C63.4:200315.207 Passed Radiated emission ANSI C63.4:200315.209 Passed 6 dB bandwidth DTS guide:2005 15.247(a)(2) Passed Conducted power output DTS guide:2005 15.247(b)(3) Passed Conducted spurious emissions DTS guide:2005 15.247(c) Passed Power spectral density DTS guide:2005 15.247(d) Passed Test Method: DTS guide:2005 full name is “Measurement of Digital Transmission Sys- tem operating under section 15.247, March 23, 2005” The given result is based on a shared risk principle with respect to the measurement un- certainty. Conclusion The test objects mentioned in this report meet the requirements of the standard stated be- low.  FCC CFR 47 Part 15, Subpart C Specific rule part 15.247. The test results relate only to the objects tested. DANAK-1910853, Rev. B DELTA-A506404-1 Page 6 of 56 JAS/BLJ 2. Test objects 2.1 Test objects Test object 2.1.1 Name of test object SAS-1 Model / type SAS-1 Part no. SAS-V3 Serial no. 0979000167 FCC ID X26SAS-1 Manufacturer GN Hearing A/S Supply voltage 100-240 VAC (external power supply) Software version Spurious emission firmware: Tx and Rx Deltatest090210 Cycle time 0.5 ms / 1.0 ms Comments Supplied by external power supply Test object 2.1.2 Name of test object SAS-1 Model / type SAS-1 Part no. SAS-V3 Serial no. 0979000144 FCC ID X26SAS-1 Manufacturer GN Hearing A/S Supply voltage 100-240 VAC (external power supply) Software version Spurious emission firmware: Tx and Rx Deltatest090210 Cycle time 0.5 ms / 1.0 ms Comments Antenna replaced by SMA connector and supplied by external power supply DANAK-1910853, Rev. B DELTA-A506404-1 Page 7 of 56 JAS/BLJ 2.2 Auxiliary equipment Auxiliary equipment 2.2.1 Name of auxiliary equipment Power supply for Stationary Audio Streamer Model / type FW7600/05 Part no. PS-0001 Serial no. 0001 FCC ID - Manufacturer FWHK Supply voltage 100-240 VAC 50-60 Hz Comments Auxiliary equipment supplied by the client Auxiliary equipment 2.2.2 Name of auxiliary equipment Apple iPod music player Model / type iPod Part no. - Serial no. - FCC ID - Manufacturer Apple Supply voltage Battery Comments - Auxiliary equipment supplied by the client Auxiliary equipment 2.2.3 Name of auxiliary equipment PC Laptop Model / type ThinkPad T43 Part no. 2669-CTO Serial no. L3-KTDP6 FCC ID - Manufacturer IBM Supply voltage 100-240 VAC via adaptor for Test PC Comments Test PC Auxiliary equipment supplied by the client DANAK-1910853, Rev. B DELTA-A506404-1 Page 8 of 56 JAS/BLJ 3. General test conditions 3.1 Test setup during test Figure 3.1.1 Block diagram of test object. All test objects were running special test software. During test, the test objects were in continuous Tx mode. (Normal modulation, normal data packets with …

Text truncated - open the document above for the full version.

DELTA Venlighedsvej 4 2970 Hørsholm Denmark Tel. +45 72 19 40 00 Fax +45 72 19 40 01 www.delta.dk VAT No. 12275110 Version l The report must not be reproduced, except in full, without the written approval of DELTA. Photos Radio parameter test of SAS-1 Performed for GN Hearing A/S Page 1 of 11 This exhibit is an extract of DELTA Test Report A506404-1 DANAK-1910853, Rev. A dated 13 April 2010 containing only the photos of the test set-ups DELTA-A506404-1 Page 2 of 11 JAS/BLJ Photo 4.1.1 Test setup regarding measurement of antenna requirement Photo 4.1.2 Test setup regarding measurement of antenna requirement DELTA-A506404-1 Page 3 of 11 JAS/BLJ Photo 4.2.1 Test setup regarding measurement of radio frequency voltage on mains. Photo 4.2.2 Test setup regarding measurement of radio frequency voltage on mains. DELTA-A506404-1 Page 4 of 11 JAS/BLJ Photo Error! No text of specified style in document..1 Test setup regarding measure- ment of radiated emission, 0.009-30 MHz. Photo Error! No text of specified style in document..2 Test setup regarding measure- ment of radiated emission, 0.009-30 MHz. DELTA-A506404-1 Page 5 of 11 JAS/BLJ Photo Error! No text of specified style in document..3 Test setup regarding measure- ment of radiated emission, 0.009-30 MHz. Photo Error! No text of specified style in document..4 Test setup regarding measure- ment of radiated emission, 0.009-30 MHz. DELTA-A506404-1 Page 6 of 11 JAS/BLJ Photo 4.4.1 Test setup regarding measurement of radiated emission, 30 to 1000 MHz. Photo 4.4.2 Test setup regarding measurement of radiated emission, 30 to 1000 MHz. DELTA-A506404-1 Page 7 of 11 JAS/BLJ Photo 4.5.1 Test setup regarding measurement of radiated emission, 1 GHz to 25 MHz. Photo 4.5.2 Test setup regarding measurement of radiated emission, 1 GHz to 25 MHz. DELTA-A506404-1 Page 8 of 11 JAS/BLJ Photo 4.6.1 Test setup regarding measurement of the 6 dB bandwidth. Photo 4.6.2 Test setup regarding measurement of the 6 dB bandwidth. DELTA-A506404-1 Page 9 of 11 JAS/BLJ Photo 4.7.1 Test setup regarding measurement of conducted power output. Photo 4.7.2 Test setup regarding measurement of conducted power output. DELTA-A506404-1 Page 10 of 11 JAS/BLJ Photo 4.8.1 Test setup regarding measurement of conducted spurious emission. Photo 4.8.2 Test setup regarding measurement of conducted spurious emission. DELTA-A506404-1 Page 11 of 11 JAS/BLJ Photo 4.9.1 Test setup regarding measurement of power spectral density. Photo 4.9.2 Test setup regarding measurement of power spectral density.