X2U-ORCA-USBDOrca USB Dongle Data Card

Orca USB Dongle User Manual z USB Driver Installation 1. To install the VIA USB Windows device driver, you must first start the Setup application, VIA USB Drivers 2.1.5 (32-Bit).exe, by double-clicking the associated icon. 2. Choose the directory for the application to be installed. 3. Click Install, then this setup program will copy all the files into the directories on the local system drive of your PC. The following dialog box will appear upon execution. 4. Click Finish when this action has been completed. 5. Power up the laptop/desktop, then Windows will install all the related drivers automatically. You can find “VIA Telecom USB Modem”, “VIA Telecom AT Port”, “VIA Telecom LBS Port”, “VIA Telecom Voice Port” and “VIA Telecom USB ETS” in Device Manager. z Dial up Application Setup 1. Select “New Connection Wizard” 2. Select Connect to the Internet 3. Select “Set up my connection manually” 4. Select” Connect using a dial- up modem” 5. Enter your ISP name 6. Enter your Number to Dial 7. Select Anyone’s use 8. Enter user name and password 9. After finishing the configuration, you can set up a connection If Driver is properly installed, you can see “VIA Telecom USB Modem” in the properties menu. z IMPORTANT NOTE: FCC Section 15.19 Labelling requirements. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC Section 15.21 Information to user Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. FCC Section 15.105(b) Information to user This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: —Reorient or relocate the receiving antenna. —Increase the separation between the equipment and receiver. —Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. —Consult the dealer or an experienced radio/ TV technician for help.

external photo

internal photo

Report No.: SH10070018E01 Page 2 of 14 TABLE OF CONTENTS 1 TEST CERTIFICATION ............................................................................................................... 3 2 GENERAL INFORMATION ......................................................................................................... 4 2.1 EUT Description ......................................................................................................................... 4 2.2 Test Standards and Results ........................................................................................................ 5 2.3 Facilities and Accreditations ...................................................................................................... 5 2.3.1 Facilities .................................................................................................................................... 5 2.3.2 Test Environment Conditions .................................................................................................... 5 3 TEST CONDITIONS SETTING ................................................................................................. 6 3.1 Test Mode .................................................................................................................................... 6 3.2 Test Setup and Equipments List ................................................................................................. 7 3.2.1 Conducted Emission.................................................................................................................. 7 3.2.2 Radiated Emission ..................................................................................................................... 8 47 CFR PART 15B REQUIREMENTS ............................................................................................... 9 4 Conducted Emission ................................................................................................................... 9 4.1 Requirement .................................................................................................................................. 9 4.2 Test Description ............................................................................................................................ 9 4.3 Test Result .................................................................................................................................... 9 5 Radiated Emission .................................................................................................................... 12 5.1 Requirement ................................................................................................................................ 12 5.2 Test Description .......................................................................................................................... 12 5.3 Test Result .................................................................................................................................. 12 Report No.: SH10070018E01 Page 4 of 14 2 GENERAL INFORMATION 2.1 EUT Description EUT Type ............................. : Orca USB Dongle Data Card Brand Name ......................... : / Model Name ........................ : Orca USB Dongle Frequency Range ................. : CDMA2000 Cellular: Tx: 824 MHz ~ 849 MHz; Rx: 869 MHz ~ 894 MHz CDMA2000 PCS: Tx: 1850 MHz ~1910 MHz;Rx: 1930 MHz ~ 1990 MHz Modulation Type .................. : OQPSK Emission Designators .......... : 1M25F9W Hardware Version ................. : P3 Software Version .................. : 8.5.16.35 Manufacturer ........................ : VIA Telecom, Inc. 3390 Carmel Mountain Road, San Diego, CA 92121-1002, USA Factory ................................. : Hangzhou Manko Technology CO.,LTD. No. 77 ChunChao Road, XiaoShan Economic Development Zone, Hangzhou, Zhejiang Note 1: The EUT is a CDMA2000 1x RTT USB Dongle operating in Cellular 800MHz band and PCS1900MHz band. Note 2: The normal configuration for the EUT is connected with the PC via the USB port. Note 3: For a more detailed description, please refer to Specification or User’s Manual supplied by the applicant and/or manufacturer. Report No.: SH10070018E01 Page 5 of 14 2.2 Test Standards and Results The objective of the report is to perform testing according to 47 CFR Part 15 Subpart B: No. Identity Document Title 1 47 CFR Part 15 (10-1-05 Edition) Radio Frequency Devices 2 ANSI/TIA/EIA-603-C (2004) Land Mobile FM or PM - Communications Equipment - Measurement and Performance Standards 3 ANSI C63.4-2003 American National Standard for Methods of Measurement of Radio-Noise Emissions from Low-Voltage Electrical and Electronic Equipment in the Range of 9 kHz to 40 GHz Test detailed items/section required by FCC rules and results are as below: No. Section Description Result 1 15.107 Conducted Emission PASS 2 15.109 Radiated Emission PASS 2.3 Facilities and Accreditations 2.3.1 Facilities Shenzhen Electronic Product Quality Testing Center Morlab Laboratory is a testing organization accredited by China National Accreditation Service for Laboratories (CNAS) according to ISO/IEC 17025. The accreditation certificate number is L1659. All measurement facilities used to collect the measurement data are located at Electronic Testing Building, Shahe Road, Xili, Nanshan District, Shenzhen 518055 CHINA. The test site is constructed in conformance with the requirements of ANSI C63.7, ANSI C63.4 and CISPR Publication 22; the FCC registration number is 741109. 2.3.2 Test Environment Conditions During the measurement, the environmental conditions were within the listed ranges: Temperature (°C): 20 – 25 Relative Humidity (%): 40 – 60 Atmospheric Pressure (kPa): 96 Report No.: SH10070018E01 Page 6 of 14 3 TEST CONDITIONS SETTING 3.1 Te s t M o d e 1. The test modes of the EUT are showed as below: a) The first test mode (CDMA 1x RTT) The EUT configuration of the emission tests is EUT + PC. During the measurement, the EU…

Text truncated - open the document above for the full version.

Test Setup Photo Radiation Te s t Setup Conducted Te s t Setup