X66-WMD-01WHITEBOARD WIRELESS MODULE-DONGLE

User Manual 1. How to Install Hardware A. Use a socket spanner screw off the cap (nearby the USB socket, back of the Hiteboard, circled by red line in the picture below), then fasten the steel bracket with wireless module by this screw cap. B. Connect Hiteboard and wireless module by USB cable, and power up the wireless module. 2. Hiteboard Settings A. For QWB56, QWB200, QWB300 and QWB100WS, you should switch Hiteboard to COM port mode first. B. For QWB200frame, you should switch main board to TTL position first. C. This wireless module can not support QWB200slim. 3. Driver Install A. Put Wireless Module Driver CD into the computer B. Plug Dongle to USB port, Windows will show the ‘Found New Hardware Wizard’, choose “No, not this time” and click ‘Next’. Please see the picture below. Then choose ‘Install from a list or specific location (Advanced)’ and click ‘Next’. Please location to your CD-ROM driver, the Windows will install driver automatically. C. If there is a ‘Hardware Installation’ window (see the picture below), please click ‘Continue Anyway’. D. Once install finished, you can run the DigitalPenServer to start using Hiteboard. 4. Search Hiteboard A. Double click DigitalPenServer tray icon, then click ‘FindModule’. Wait for a few seconds the ‘Find module’ window will change to like this Click ‘Module list’, searched modules will show in the list. The eight numbers before the colon ‘:’ like ’00 02 01 09 09 18 00 06’ are the MAC address of wireless module, and each module has an unique MAC address. After the colon ‘:’, there should be eight characters for user to describe the Hiteboard which connect to this module, and it’s blank in default mode. You can input no more than eight characters into the ‘Module’ input box to describe the Hiteboard which connect to this module. Showing in the below picture. B. After chosen module, click ‘OK’ to bind module with Dongle. 5. Bind Dongle with Hiteboard If bind is successful, there should be a message box showing ‘Bind OK’, then click ‘OK’ to start connect to Hiteboard, it will take about 10 seconds to connect. After connect success, the using is same as connect by USB cable. 6. Notes A. Before searching wireless module, please make sure wireless module is power on. If searching failed, please click ‘Cancel’ and try it again. If still can not find any wireless module, please reset wireless module or reduce the distance between dongle and wireless module. B. While using wireless module, please make sure the distance between dongle and wireless module is less than 20m. 7. FCC Statement NOTE 1: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Note: The manufacturer is not responsible for ANY interference, for example RADIO or TV interference, caused by unauthorized modifications to this equipment. Such modifications could void the user’s authority to operate the equipment. NOTE 2: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help.

AC Power Block Diagram TX Part Crystal (32MHz) DC convert circuit Adapter Interface/port Drawing Board RF IC 2415MHz

深圳市华标电子科技有限公司 Bontek Compliance Testing Laboratory Ltd DATE: February 25, 2010. Dear TCB Section of Timco Engineering, Inc., Thank you for cooperation. I would like to submit FCC application of Hitevision Digital Media Technology Co., Ltd. FCC ID: X66-WMD-01 by your TCB Approval today. Best Regards, Bontek Compliance Testing Laboratory Ltd. Tony Wu/General Manager

Hitevision Digital Media Technology Co., Ltd. FCC ID: X66-WMD-01 POWER OF ATTORNEY February 25, 2010 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 To Whom It May Concern: We, the undersigned, hereby authorize Bontek Compliance Testing Laboratory Ltd.(Tony Wu) on our behalf, to apply to the Federal Communications Commission on our equipment. Any and all acts carried out by Bontek Compliance Testing Laboratory Ltd. (Tony Wu) on our behalf shall have the same effect as acts of our own. This is to advise that we are in full compliance with the Anti-Drug Abuse Act.We, Hitevision Digital Media Technology Co., Ltd.are not subject to a denial of federal benefits pursuant to Section 5301 of the Anti-Drug Act of 1988, 21 USC853a, and no party to the application is subject to a denial of federal benefits pursuantto that section. Sincerely, Hitevision Digital Media Technology Co., Ltd. Ligen Wang (Quality Engineer)

External Photographs The external photographs of TX Part EUT - Front View This port connect to drawing board EUT - Rear View

FCC ID Label Sample for FCC ID:X66-WMD-01 FCC ID: X66-WMD-01 Model: WMD-01 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

FCC ID Location FCC ID Location of TX Part

Internal Photographs EUT – Uncovered View of TX part EUT - PCB View of TX part

Operational Description The circuit is made up of receiver and transmitter. The EUT is transmiter (remote control). First of all, the system power on, then press button of controller. The EUT will transmit RF signals to achieve information transmission function. The 2.4 G MOD is a module that can encode the data from the Wireless drawing boardand sends these data via RF at 2.4GHz band. The 2.4 G MOD is equipped with a complete modulator that provides 1RF channel . The transmitter of the EUT is supplied by adapter. The antenna is integral antenna without connector and is permanent. The receiver connect to USB Port of PC,and install driver .Then PC indentify it ,the transmiter can connect to PC through receiver,and can achieve transmit information of drawing board to PC function.

1 2 3 4 5 6 78 ABCD 8 7 6 5 4 3 2 1 D CBA 项目名称：图纸名称： 图纸版本： 制图： 制图时间： 审核： 批准： 项目编号： GND 1 2 3 4 5 6 7 8 9 VDD 10 111213141516 171819202122 U2WSN 12 P1 J1 C1104 3V3 EC2 47uF/10V EC1100uF/10V 2 1 3 VV GND IN OUT U1FST3301A33GM C2104 LED1LED R11RES1 Q1NPN Q2NPN R1RES1 R2RES1 R10RES1 R4RES1 VCC VCC ZD3DIODE SCHOTTKY R6RES1 R5RES1 VCC 1234 USB1CON4 VCC R7 RES1 R8 RES1 3V3 rxtx TX rx RX tx TXRX R9 RES1 R10 RES1 2 415 M Hz 32 MHz

Test Report of FCC Part 15 C for FCC Certificate On Behalf of Hitevision Digital Media Technology Co., Ltd. Product description: Whiteboard wireless module-Dongle Model No.: WMD-01 FCC ID: X66- WMD-01 Prepared for: Hitevision Digital Media Technology Co., Ltd. No.1 Building, Hong Hui Industrial Park, Liu Xian No.2 Road, No.68 Zone,Bao An district, Shenzhen Prepared by: Bontek Compliance Testing Laboratory Ltd. 1/F, Block East H-3, OCT Eastern Ind. Zone, Qiaocheng East Road, Nanshan, Shenzhen, China Tel: 86-755-86337020 Fax: 86-755-86337028 Report No.: BCT10AR-0122E Issue Date: February 23, 2010 Test Date: January 01~February 23, 2010 Test by: Reviewed By: Kendy Wang Tony Wu Report No.: BCT10AR-0122E Page 2 of 23 FCC ID: X66-WMD-01 TABLE OF CONTENTS 1. GENERAL INFORMATION............................................................................................................... 3 1.1 Product Description for Equipment Under Test (EUT) ............................................................ 3 1.2 Related Submittal(s) / Grant (s) .............................................................................................. 3 1.3 Test Methodology ................................................................................................................... 3 1.4 Test Facility............................................................................................................................. 4 2. SYSTEM TEST CONFIGURATION .................................................................................................. 5 2.1 EUT Configuration .................................................................................................................. 5 2.2 EUT Exercise .......................................................................................................................... 5 2.3 General Test Procedures........................................................................................................ 5 2.4 List of Measuring Equipments................................................................................................. 6 3. SUMMARY OF TEST RESULTS ......................................................................................................8 4. TEST OF CONDUCTED EMISSION ................................................................................................. 9 4.1 Applicable Standard................................................................................................................ 9 4.2 Test Setup Diagram ................................................................................................................ 9 4.3 Test Result.............................................................................................................................. 9 5- BAND EDGES MEASUREMENT ................................................................................................... 12 5.1 Limit of Band Edges Measurement..................................................................................... 12 5.2 EUT Setup ............................................................................................................................ 12 5.3 Test Procedure ..................................................................................................................... 13 5.4 Test Result............................................................................................................................ 13 6- SPURIOUS EMISSIONS................................................................................................................. 15 6.1 Limit of Spurious Emissions.................................................................................................. 15 6.2 EUT Setup ............................................................................................................................ 16 6.3 Test Procedure ..................................................................................................................... 17 6.4 Spurious Emissions Test Result ........................................................................................... 17 7. ANTENNA REQUIREMENT............................................................................................................ 23 7.1 Standard Applicable.............................................................................................................. 23 7.2 Antenna Connected Construction ......................................................................................... 23 Report No.: BCT10AR-0122E Page 3 of 23 FCC ID: X66-WMD-01 1. GENERAL INFORMATION 1.1 Product Description for Equipment Under Test (EUT) Applicant: Hitevision Digital Media Technology Co., Ltd. Address of applicant: No.1 Building, Hong Hui Industrial Park, Liu Xian No.2 Road, No.68 Zone,Bao An district, Shenzhen Manufacturer: Hitevision Digital Media Technology Co., Ltd. Address of manufacturer: 11th Floor, Build C, Jinyu Jiahua Building, No.9th Shangdi 3rd Street, Haidian District, Beijing EUT Description: Whiteboard wireless module-Dongle Model No.: WMD-01 Rated Voltage: DC 5V from Adapter Frequency range: 2.415GHz Number of channels: 1 Product Class: Low Power Communication Device Transmitter Measurement Procedure: ANSI C63.4-2009 Adapter Specification: Input: AC 100-240V 50/60Hz 0.15A Output: DC 5.0V 1.0A Remark: * The test data gathered are from the production sample provided by the manufacturer. 1.2 Related Submittal(s) / Grant (s) This submittal(s) is a test report based on the Electromagnetic Interference (EMI) tests performed on the EUT. The EMI measurements were performed according to the measurement procedure described in ANSI C63.4 - 2009. The tests were performed in order to determine compliance with Section 15.107 and 15.109 under the FCC Rules Part 15 Subpart B and Section 15.207, 15.209,15.249 under the FCC Rules Part 15 Subpart C. 1.3 Test Methodology Both conducted and radiated testing were performed according …

Text truncated - open the document above for the full version.

TEST SETUP PHOTOGRAPHS TX part: Conducted Emission Radiated Emission