X6ZRP24RS5DX2.4 GHz RADIO CONTROL

User's Manual Handbuch RF䊝䉳䊠䊷䊦䊶䊧䉲䊷䊋䊷ขᛒ⺑᣿ᦠ RFβʨ / Ύչдӡٝԋύԅ * This user guide is subject to change without notice. RP24TD9 RP24TD9J RP24TD9M RP24RA4D RP24RA5D RP24RA6D RP24RA8D RP24RA9D Ver. 2.0 www.rcenjoy.com Tx 2.4GHz Radio Control Receiver &OHMJTI ڌڋ Introduction The existing 2.4GHz Radio Control and receivers cause inconvenience to RC users because of restricted frequency use, which comes from FM radio technology. Utilizing digital spectrum technology within the 2.4 GHz ISM band, the Radiopost RF System provides secure radio link, high transmission speed and superb resolution allowing the device to respond quickly and accurately without interference. The Radiopost Tx 2.4GHz Radio Control and receivers offer a significant advantage of eliminating the possibility of interference. Each Tx 2.4GHz Radio Control is programmed with a unique identification code to communicate with its specified receiver. Once the receiver is paired with the Tx 2.4GHz Radio Control (called ID Setting), the receiver will only take data from this specific radio controller where the Tx 2.4GHz Radio Control is equipped, ignoring signals from other sources. The Radiopost Tx 2.4GHz Radio Control and receivers scan and select the superior channels that are not being used to avoid collision in channels and data loss between the Tx 2.4GHz Radio Control and the receiver. This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC Information &OHMJTI ڍڋ Precautions Read this manual before installation or use. Do not disassemble the Tx 2.4GHz Radio Control and the receiver because it may cause severe damage or problems. Install the Tx 2.4GHz Radio Control and the receiver after cutting off the power of the radio controller and RC models such as model aircrafts or helicopters or cars. The receiver should be turned on after the radio controller is switched on. When turning on the radio controller, be sure to put the throttle to the stop position. When switching off, make sure the engine or the motor of the RC models should be stopped. First, switch off the receiver thenthe radio controller. If this is not done in this order, it may cause temporary malfunctions. Prior to actual use and control of RC models, perform operation tests between the Tx 2.4GHz Radio Control and the receiver. If these tests fail, do not operate RC models. When installing the receiver in RC models, use impact protection materials to avoid damage to the receiver, which may be caused by the vibration of RC models or the impact from the outside. Do not alter length of antenna arbitrarily. The antenna should not be hidden by the RC model's main body or cover, coated with metallic paint or carbon fiber. Do not use Radiopost Tx 2.4GHz Radio Control and receivers together with Tx 2.4GHz Radio Control and receivers produced by other manufacturers. Do not operate the Tx module with two or more receivers. The receiver antenna shall be installed not to get affected by the magnetic field of power cables. * Nextlink will not be responsible for damage caused by use which is prohibited. 4BGFUZ $BVUJPO &OHMJTI ڎڋ Name of Each Part RP24TD9JRP24TD9 ID Setting Button ID Setting Button Status LED Status LED ID Setting Button Status LED RP24TD9M RP24RA4DRP24RA8DRP24RA9DRP24RA6DRP24RA5D [For JR radio controllers] [For Sanwa radio controllers] [For Futaba and Hitec radio controllers] www.rcenjoy.com Spread Spectrum 2.4GHz2.4GHz RF MODULE www.rcenjoy.com ID SETSTATUS RP24TD9J 2.4GHz2.4GHz RF MODULE ID SETSTATUS RP24TD9RP24TD9 www.rcenjoy.com AntennaAntenna Antenna Status LED ID Setting Button RP24RA6DRP24RA6D 2.4GHz2.4GHz 6CH Receiver ID SET ՙ՞Շՙ՞Ոՙ՞Չՙ՞Պՙ՞Ջ ՘Յՙ՞Ռ www.rcenjoy.com Antenna Antenna Status LED ID Setting Button Failsafe Button RP24RA8DRP24RA8D 2.4GHz2.4GHz 8CH Receiver I D S E T F / S ՙ՞Շՙ՞Ոՙ՞Չ ՙ՞Պ ՙ՞Ջՙ՞Ռՙ՞Ս ՘Յՙ՞Վ www.rcenjoy.com Antenna Status LED ID Setting Button Failsafe Button Status LED ID Setting Button ՙՇ ՙՈՙՉՙՊ ՘ՅՙՋ 55 C h a n n e l R e c e i v e r www.rcenjoy.com 2.4GHz2.4GHz RP24RA5DRP24RA5D Antenna Status LED ID Setting Button Antenna ID SET 2.4GHz2.4GHz RP24RA4DRP24RA4D 44 ChannelChannel Tx 2.4GHz Radio Control Receiver &OHMJTI ڏڋ Tx Module Features High stability is guaranteed by using 2.4 GHz ISM bandwidth. Crystal is not necessary due to automatic channel selection. ID Setting is checked by beeping sounds. Binding speed is superior. The embedded Tx 2.4GHz Radio Control antenna provides convenience for users when the stand is attached to the radio controller. Radiopost Tx 2.4GHz Radio Control can be paired with any Radiopost receivers. It provides a wide range and high durability. It is a highly sensitive receiver which is less affected by intermodulation It is a universal type which can be used for model aircrafts,helicopters and cars. It is free from "NO CONTROL" after ID Setting. The Failsafe Function(only applied to RP24RA8D/ RP24RA9D) minimizes damage to RC models caused by accident. Receiver &OHMJTI ڐڋ LED Status by Function When powered on for the first time, the white LED blinks. When ID Setting button is pressed, the white LED blinks faster than previously. When ID Setting is done, the LED turns green and remains still. The white LED blinks slowly if there is no data transferred from the Tx 2.4GHz Radio Control LED turns green White LED blinks slowly White LED blinks Power Tx Module Red LED blinks Receiver Green LED blinks. Green color remains still White LED blinks faster When powered on for the first time, the green LED blinks turning into the receiver searching status. When ID Setting button is pressed, it turns into ID-Setting mode and the red LED blinks. When ID Setting is done, the LED turns green and the green color remains still. &OHMJTI ڑڋ Installation Instructions White LED blinks Power Choose a Tx 2.4GHz Radio Co…

Text truncated - open the document above for the full version.

Nextlink Co., Ltd. 701, Jungang Induspia II #144-5 Sangdaewon-dong, Jungwon-gu Seongnam-si, Gyeonggi-do, Korea Date: 2012.04.13 Federal Communications Commission 7435 Oakland Mills Road Columbia MD 21046 To whom it may concern: I, the undersigned, hereby authorize KT Kang of KES Co., Ltd. and hereafter referred to as KES Co., Ltd., to act on our behalf in all manners relating to application for equipment authorization, including signing of all documents relating to these matters. Any and all acts carried out by KT Kang of KES Co., Ltd. on our behalf shall have the same effect as acts of our own. I, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). In authorizing KES Co., Ltd. as our agent, we still recognize that we are responsible to: a) comply with the relevant provisions of the certification program; b) make all necessary arrangements for the conduct of the evaluation, including provision for examining documentation and access to all areas, records (including internal audit reports) and personnel for the purposes of evaluation (e.g. testing, inspection, assessment, surveillance, reassessment) and resolution of complaints; c) make claims regarding certification only in respect of the scope for which certification has been granted; d) do not use our product certification in such a manner as to bring the Certification Division into disrepute and not make any statement regarding our product certification which the Certification Division may consider misleading or unauthorized; e) upon suspension or cancellation of certification, discontinue use of all advertising matter that contains any reference thereto and return any certification documents as required by the Certification Division; f) use certification only to indicate the products are certified as being in conformity with specified standards; g) endeavor to ensure that no certificate or report nor any part thereof is used in a misleading manner; Nextlink Co., Ltd. 701, Jungang Induspia II #144-5 Sangdaewon-dong, Jungwon-gu Seongnam-si, Gyeonggi-do, Korea h) ensure that any reference to our product certification in communication media such as documents, brochures or advertising, complies with the requirements of the Certification Division; i) keep a record of all complaints made known to the us relating to the product’s compliance with requirements of the relevant standard and to make these records available to the Certification Division when requested; j) take appropriate action with respect to such complaints and any deficiencies found in products or services that affect compliance with the requirements for certification; k) document the actions taken. This authorization is valid until further written notice from the applicant. Sincerely Yours, Jum-Su Kim / Manager Nextlink Co., Ltd. REMARK: 1. This authorization letter will be sent along with your application when filing with the Certification Division. 2. Please follow the format and type it on company letterhead and send original to us. 3. Authorized signature must be in agreement with grantee code contact in FCC database.

Nextlink Co., Ltd. 701, Jungang Induspia II #144-5 Sangdaewon-dong, Jungwon-gu Seongnam-si, Gyeonggi-do, Korea Date: 2012.04.13 Federal Communications Commission Authorization and Evaluation Division Confidentiality Request regarding application for certification of FCC ID: X6ZRP24RS5DX Pursuant to Sections 0.457 and 0.459 of the Commission’s Rules, we hereby request confidential treatment of information accompanying this application as outlined below: Exhibit Type File Name Part List CONF APPENDIX_RP24RS5DX _Part List.PDF Schematics Diagram(s) CONF APPENDIX_ RP24RS5DX _Schemetics.PDF Block diagram CONF APPENDIX_ RP24RS5DX _Block diagram.PDF Operation description CONF APPENDIX_ RP24RS5DX _Operation description.PDF The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. The applicant understands that pursuant to Section 0.457 of the Rules, disclosure of this application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely, Jum-Su Kim / Manager Nextlink Co., Ltd.

www.kes.co.kr Model No.: RP24RS5DX Page 1 of 2 EUT External photographs www.kes.co.kr Model No.: RP24RS5DX Page 2 of 2

www.kes.co.kr Model No.: RP24RS5DX Page 1 of 1 Label and Location Label Nextlink FCC ID: X6ZRP24RS5DX Model: RP24RS5DX This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation

www.kes.co.kr Model No.: RP24RS5DX Page 1 of 1 EUT Internal photographs

Antenna Gain Peak 1.83dBi

KES Co., Ltd. C-3701 Dongil Techno Town, 889-1, Gwanyang 2-dong, Dongan-gu, Anyang-si, Gyeonggi-do, 431-716, Korea Tel: +82-31-425-6200 / Fax: +82-31-424-0450 www.kes.co.kr Test report No.: KES-RF-120029 Page: (2) of (27) This report shall not be reproduced except in full, without the written approval of KES Co., Ltd. The test results in the report only apply to the tested sample. KES-P-5101-09 Rev.1 KES A4 Revision history Revision Date of issue Test report No. Description - 2012.04.13 KES-RF-120024Initial 1 2012.04.19 KES-RF-120029Retest the Maximum peak output power KES Co., Ltd. C-3701 Dongil Techno Town, 889-1, Gwanyang 2-dong, Dongan-gu, Anyang-si, Gyeonggi-do, 431-716, Korea Tel: +82-31-425-6200 / Fax: +82-31-424-0450 www.kes.co.kr Test report No.: KES-RF-120029 Page: (3) of (27) This report shall not be reproduced except in full, without the written approval of KES Co., Ltd. The test results in the report only apply to the tested sample. KES-P-5101-09 Rev.1 KES A4 TABLE OF CONTENTS 1.0 General product description ............................................................................ 4 1.1 Test frequency ........................................................................................... 4 1.2 Model differences ....................................................................................... 4 1.3 Device modifications ................................................................................... 4 1.4 Test facility .............................................................................................. 5 1.5 Laboratory accreditations and listings .................................................................. 5 2.0 Summary of tests ........................................................................................ 6 2.1 Test data ................................................................................................. 7 2.1.1 6 ㏈ Bandwidth ................................................................................... 7 2.1.2 Maximum peak output power ................................................................... 10 2.1.3 Power spectral density ........................................................................... 13 2.1.6 Conducted spurious emission & band edge ..................................................... 16 2.1.7 Radiated spurious emission & band edge ....................................................... 21 Appendix A. Test equipment used for test ...................................................................... 26 Appendix B. Test setup photo ................................................................................... 27 KES Co., Ltd. C-3701 Dongil Techno Town, 889-1, Gwanyang 2-dong, Dongan-gu, Anyang-si, Gyeonggi-do, 431-716, Korea Tel: +82-31-425-6200 / Fax: +82-31-424-0450 www.kes.co.kr Test report No.: KES-RF-120029 Page: (4) of (27) This report shall not be reproduced except in full, without the written approval of KES Co., Ltd. The test results in the report only apply to the tested sample. KES-P-5101-09 Rev.1 KES A4 1.0 General product description Equipment under test 2.4 GHz Radio Control Model name RP24RS5DX Serial number Prototype Frequency Range 2 405 ㎒ ~ 2 480 ㎒ Modulation technique DSSS Number of channels 76 Antenna type & gain Connector Type(Wire antenna) / 1.83 ㏈i Power source DC 4.8 V 1.1 Test frequency Low channel Middle channel High channel Frequency (㎒) 2 405 2 440 2 480 1.2 Model differences N/A 1.3 Device modifications N/A KES Co., Ltd. C-3701 Dongil Techno Town, 889-1, Gwanyang 2-dong, Dongan-gu, Anyang-si, Gyeonggi-do, 431-716, Korea Tel: +82-31-425-6200 / Fax: +82-31-424-0450 www.kes.co.kr Test report No.: KES-RF-120029 Page: (5) of (27) This report shall not be reproduced except in full, without the written approval of KES Co., Ltd. The test results in the report only apply to the tested sample. KES-P-5101-09 Rev.1 KES A4 1.4 Test facility C3701 Dongil Techno Town, 889-1, Gwanyang 2-dong, Dongan-gu, Anyang-si, Gyeonggi-do, 431-716, Korea 477-6, Hageo-ri, Yeoju-eup, Yeoju-gun, Gyeonggi-do, 469-803, Korea The sites are constructed in conformance with the requirements of ANSI C63.7, ANSI C63.4 and CISPR Publication 22. 1.5 Laboratory accreditations and listings Country Agency Scope of accreditation Logo USA FCC 3 & 10 meter Open Area Test Sites and one conducted site to perform FCC Part 15/18 measurements. 343818 KOREA KC EMI (10 meter Open Area Test Site and two conducted sites) Radio (3 & 10 meter Open Area Test Sites and one conducted site) KR0100 Canada IC 3 & 10 meter Open Area Test Sites and one conducted site 4769B-1 KES Co., Ltd. C-3701 Dongil Techno Town, 889-1, Gwanyang 2-dong, Dongan-gu, Anyang-si, Gyeonggi-do, 431-716, Korea Tel: +82-31-425-6200 / Fax: +82-31-424-0450 www.kes.co.kr Test report No.: KES-RF-120029 Page: (6) of (27) This report shall not be reproduced except in full, without the written approval of KES Co., Ltd. The test results in the report only apply to the tested sample. KES-P-5101-09 Rev.1 KES A4 2.0 Summary of tests Section in FCC Part 15 Parameter Status 15.247(a)(2) 6 ㏈ Bandwidth C 15.247(b)(3) Maximum peak output power C 15.247(e) Power spectral density C 15.247(d) Conducted spurious emission & band edge C 15.209 15.205(a) Radiated spurious emission & band edge C Note 1: C=Complies NC=Not complies NT=Not tested NA=Not applicable KES Co., Ltd. C-3701 Dongil Techno Town, 889-1, Gwanyang 2-dong, Dongan-gu, Anyang-si, Gyeonggi-do, 431-716, Korea Tel: +82-31-425-6200 / Fax: +82-31-424-0450 www.kes.co.kr Test report No.: KES-RF-120029 Page: (7) of (27) This report shall not be reproduced except in full, without the written approval of KES Co., Ltd. The test results in the report only apply to the tested sample. KES-P-5101-09 Rev.1 KES A4 2.1 Test data 2.1.1 6 ㏈ Bandwidth Test setup EUT Attenuator Spectrum analyzer Test procedure 1. Place the EUT on the table and set it in the transmitting mode . 2. Remove the antenna from the EUT and then connec…

Text truncated - open the document above for the full version.

KES Co., Ltd. C-3701 Dongil Techno Town, 889-1, Gwanyang 2-dong, Dongan-gu, Anyang-si, Gyeonggi-do, 431-716, Korea Tel: +82-31-425-6200 / Fax: +82-31-424-0450 www.kes.co.kr Test report No.: KES-RF-120024 Page: (26) of (26) This report shall not be reproduced except in full, without the written approval of KES Co., Ltd. The test results in the report only apply to the tested sample. KES-P-5101-09 Rev.1 KES A4 Appendix B. Test setup photo Radiated field emissions