X9V-CN-F2K349-7RF-PG20-11 WIRELESS RECEIVER

F-PG20-11 USERS MANUAL 1. Insert 1 piece battery (12V) in remote; insert 2 pieces batteries (1.5V N # ) into vibrator, the device enter “standby” mode. 2. Press the “ON/OFF” button on remote for one time, the vibrator start to vibrate; Press the “mode switch” button on remote for the first time, vibrator are in stronger vibration; Press the ““mode switch” button for the second time, vibration are strongest; press the ““mode switch” button for the third time, vibrator enter into the vibration mode of “weak to strong”; each time when user press the ““mode switch” button, vibrator will have a vibration mode of one special frequency. This unit has seven different vibration modes. 3. Press “ON/OFF” button on remote for one time, the vibrator stop vibration. VIBRATOR CARE INSTRUCTION 1) Take care when using the Vibrator for the first time. Vibration can be intense. 2) Clean your vibrator after every use. 3) Take care when cleaning your vibrator. Remember it is an electrical item. Moisture can damage the product and also react with the batteries. Always remove the batteries before cleaning and after using your vibrator in order to keep it in optimum condition. 4) Keep your vibrator clean and dry. Store in a non-damp environment. Moisture can damage batteries and motor. 5) Always store your vibrator separately. Different materials have different chemical configurations and may react with each other. 6) Always allow your vibrator to cool down before storing in a safe place. Vibrators are electrical and motors grow warm with use. 7) Excessive usage of the vibrator will wear out the motor and may cause the motor to overheat. If you feel your vibrator is getting unduly hot, switch it off and allow it to cool down, before continuing to use. 8) Take care when using oils and lubricants so that they do not enter the battery compartment as they can react with the batteries. BATTERY CARE INSTRUCTIONS 1) Batteries must be inserted with the correct polarity. 2) Remove batteries when the product is not in use. 3) The supply terminals should not be short-circuited i.e. do not bridge terminal switch metallic pieces. 4) Only use the recommended batteries. 5) Only operate when fully assembled in accordance with the instructions. 6) Do not mix different types or new and used batteries. WA R N I N G To avoid injury and aggravation of pre-existing conditions, this device should not be used on swollen or inflamed areas or skin lacerations. Do not use on unexplained calf pain. No medical claims are warranted or implied by the use of this product. FCC INFORMATION FOR THE CONSUMER This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: z Reorient or relocate the receiving antenna. z Increase the separation between the equipment and receiver. z Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. z Consult the dealer or an experienced radio/TV technician for help. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions :(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTE: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

RX Block Diagram IC U1:TM58PE10 CPU INTERNAL OSCILLATION 4Mhz OSCILLATION AMPLIFIER 315MHz IFA MOTOR DRIVE MOTOR BATTERY 3.0V RF POWER DC 2.1V ANT 315MHz

J.B. Industrial (Shen Zhen) Co., Ltd. J.B. Industrial Center, Beishandao YanTian, Shenzhen P.R.China. AGENCY AUTHORIZATION LETTER FCC ID: X9V-CN-F2K349-7R Date: February 26, 2011 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 To whom it may concern: We, the undersigned, hereby authorize Shenzhen CTL Electromagnetic Technology Co., Ltd.(MR. Tracy Qi) on our behalf, to apply to the Federal Communications Commission on our equipment. Any and all acts carried out by Shenzhen CTL Electromagnetic Technology Co., Ltd. (MR. Tracy Qi) on our behalf shall have the same effect as acts of our own. This authorization expires on December 31, 2011. This is to advise that we are in full compliance with the Anti-Drug Abuse Act. We, J.B. Industrial (Shen Zhen) Co., Ltd. are not subject to a denial of federal benefits pursuant to Section 5301 of the Anti-Drug Act of 1988, 21 USC853a, and no party to the application is subject to a denial of federal benefits pursuant to that section. Sincerely, Fenny Tseng / Director

External and Internal Photos of the EUT External Photos

FCC ID Label Information 1. Label location: 2. FCC ID Label: J.B. Industrial (Shen Zhen) Co., Ltd. Model: CN-F2K349-7R FCC ID: X9V-CN-F2K349-7R

Internal Photos

1. RX Technical Description Technical Description Description Function Component Antenna Transmit modulation RF signal Ant Oscillator Generate 315MHz HF carrier Q10,L3,L4,C28,C31 Digital shaping Shape the received signal to square wave Q2,Q12 Motor Drive Control motor vibration Q7,Q1 CPU Receive and process data U2 Amplify the received 315 MHz high frequency carrier through transistor Q10 3356, input to oscillation circuit (composed by transistor Q11 3356, L3 and C31) of this unit for frequency mixing, then input to the data reshaping circuit (composed by transistors Q2 8050 and Q12 8050, separate the data signal from high frequency carrier and transmit to MCU TM58PE10. At this moment MCU output electrical level to control the motor drive circuit (composed by transistors Q7 8050 and Q8 8050), thus to control motor vibration.

PDF 文件使用 "pdfFactory Pro" 试用版本创建 www.fineprint.cn

Shenzhen CTL Electromagnetic Technology Co., Ltd. Tel: +86-755-89486194 Fax: +86-755-89486187 FCC PART 15 SUBPART C TEST REPORT FCC PART 15B Report Reference No......................: CTL1102006-R Compiled by ( position+printed name+signature)..: File administrators Andy Zhang Name of the organization performing the tests ( position+printed name+signature)..: Test Engineer Kendy Wang Approved by ( position+printed name+signature)..: Manager Tracy Qi Date of issue.....................................: February 28, 2011 Testing Laboratory Name..............: Shenzhen CTL Electromagnetic Technology Co., Ltd. Address.............................................: Zone B，4/F, Block 20，Guangqian Industrial Park, Longzhu Road,Nanshan,Shenzhen 518055 China. Test Firm..........................................: Bontek Compliance Testing Laboratory Ltd Address.............................................: 1/F, Block East H-3, OCT Eastern Ind. Zone, Qiaocheng East Road, Nanshan, Shenzhen, China Applicant’s name............................: J.B. Industrial (Shen Zhen) Co., Ltd. Address.............................................: J.B. Industrial Center, Beishandao YanTian, Shenzhen P.R.China. Test specification: Standard ...........................................: FCC Part 15B ANSI C63.4: 2003 TRF Originator ..................................: Shenzhen CTL Electromagnetic Technology Co., Ltd. Master TRF.......................................: Dated 2011-01 Shenzhen CTL Electromagnetic Technology Co., Ltd. All rights reserved. This publication may be reproduced in whole or in part for non-commercial purposes as long as the Shenzhen CTL Electromagnetic Technology Co., Ltd. is acknowledged as copyright owner and source of the material. Shenzhen CTL Electromagnetic Technology Co., Ltd. takes no responsibility for and will not assume liability for damages resulting from the reader's interpretation of the reproduced material due to its placement and context. Test item description .................... : F-PG20-11 Operation Frequency........................: 315MHz Modulation mode: ............................: ASK Trade Mark .......................................: Model/Type reference.......................: CN-F2K349-7R Listed Models ..................................: / Power Supply..............................: DC 3V Anttenna Type..............................: Integral without external RF Port Result................................................: Positive FCC ID............................................. : X9V-CN-F2K349-7R V1.0 Page 2 of 17 Report No.: CTL1102006-R T E S T R E P O R T Test Report No. : CTL1102006-R February 28, 2011 ______________________________________________________________________________________________ Date of issue Equipment under Test : F-PG20-11 Model /Type : CN-F2K349-7R Listed Models : / Difference description: / Applicant : J.B. Industrial (Shen Zhen) Co., Ltd. Address : J.B. Industrial Center, Beishandao YanTian, Shenzhen P.R.China. Manufacturer : J.B. Industrial (Shen Zhen) Co., Ltd. Address : J.B. Industrial Center, Beishandao YanTian, Shenzhen P.R.China. Test Result according to the standards on page 4: Positive The test report merely corresponds to the test sample. It is not permitted to copy extracts of these test result without the written permission of the test laboratory. V1.0 Page 3 of 17 Report No.: CTL1102006-R Contents 1. TEST STANDARDS .................................................................. 4 2. SUMMARY............................................................................. 5 2.1. General Remarks 5 2.2. Equipment Under Test 5 2.3. Short description of the Equipment under Test (EUT) 5 2.4. EUT operation mode 5 2.5. EUT configuration 5 2.6. Related Submittal(s) / Grant (s) 6 2.7. Modifications 6 2.8. Test Result Summary 6 3. TEST ENVIRONMENT............................................................... 7 3.1. Address of the test laboratory 7 3.2. Test Facility 7 3.3. Environmental conditions 7 3.4. Configuration of Tested System 7 3.5. Statement of the measurement uncertainty 8 3.6. Equipments Used during the Test 8 4. TEST CONDITIONS AND RESULTS ............................................. 9 4.1. Radiated Emission Test 9 4.2. Conducted Emissions Test 13 5. TEST SETUP PHOTOS OF THE EUT .......................................... 14 6. EXTERNAL AND INTERNAL PHOTOS OF THE EUT ....................... 15 V1.0 Page 4 of 17 Report No.: CTL1102006-R 1. TEST STANDARDS The tests were performed according to following standards: FCC Rules Part 15 Subpart B - Unintentional Radiators ANSI C63.4: 2003 V1.0 Page 5 of 17 Report No.: CTL1102006-R 2. SUMMARY 2.1. General Remarks Date of receipt of test sample : February 21, 2011 Testing commenced on : February 23, 2011 Testing concluded on : February 25, 2011 2.2. Equipment Under Test Power supply system utilised Power supply voltage : o 120V / 60 Hz o 115V / 60Hz o 12 V DC o 24 V DC z Other (specified in blank below) DC 3V from battery 2.3. Short description of the Equipment under Test (EUT) 315MHz Receiver For more details, refer to the user’s manual of the EUT. Serial number: Prototype 2.4. EUT operation mode The EUT has been tested under typical operating condition. 2.5. EUT configuration The following peripheral devices and interface cables were connected during the measurement: o - supplied by the manufacturer o - supplied by the lab o Power Cable Length (m) : / Shield : / Detachable : / o Multimeter Manufacturer : / Model No. : / V1.0 Page 6 of 17 Report No.: CTL1102006-R 2.6. Related Submittal(s) / Grant (s) This submittal(s) (test report) is intended for FCC ID: X9V-CN-F2K349-7R filing to comply with the FCC Part 15, Subpart B Rules. 2.7. Modifications No modifications were implemented to meet testing criteria. 2.8. Test Result Summary Test Item Test RequirementStandard Paragrph Result Radiated Emission FCC PART 15 Section 15.109 PASS Conducted Emission FCC PART 15 Section 15.107 N/A V1.0 Page 7 o…

Text truncated - open the document above for the full version.

Test Setup Photos of the EUT