XAB-HEDDI-X219Remote Controller

INSTRUCTIONS FOR RADIO CONTRO L OPERATOR SINGLE ENT RY TRANSMITTER MODEL NO.:X219-1 Read the following instructions thoroughly before using transmitter. This transmitter must be adjusted so that the coding switches match the coding switches on your present operating transmitter or receiver. 1.Remove the transmitter cover a Unscrew the screws(Figure A). b Remove the front cover from the transmitter(Figure B). c In order to facilitate the replacement of the battery. FIGURE AFIGURE B User manual FCC NOTE: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:(1) this device may not cause harmful interference,and (2) this device must accept any interference received,including interference that may cause undesired operation. THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV INTERFERENCE CAUSED BY UNAUTHORIZED MODIFICATIONS OR CHANGE TO THIS EQUIPMENT. SUCH MODIFICATIONS OR CHANGE COULD VOID THE USER’S AUTHORITY TO OPERATE THE EQUIPMENT. 2.The transmitter is rolling code encoding and transmitting, it will automatically and receiver code matching. If the receiver successfully decoded, the receiver will normally work. User can click the push button,A signal tramsit out.

1 2 34 ABCD 4 3 2 1 D CBA Title Number Revision Size A4 Date: 30-Jun-2014 Sheet of File: E:\lu\RF Products\P220 Old Remote C ontroller Info\P220 Remote Controll.DDB Drawn By: BLOCK DIAGRAMROLLING CODE CHIP RF CHIP MICRF113 HCS300/HCS301 PCB ANTENNA DATA OUTPUT X219 BLOCK DIAGRAM DC 3V By Battery 13.56MHz

Heddolf Products Ltd. FCC ID: XAB-HEDDI-X219 POWER OF ATTORNEY Date: May 24,2014 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 To Whom It May Concern: We, the undersigned, hereby authorize Waltek Services (ShenZhen) Co., Ltd. (Philo Zhong) on our behalf, to apply to the Federal Communications Commission on our equipment. Any and all acts carried out by Waltek Services (ShenZhen) Co., Ltd. (Philo Zhong) on our behalf shall have the same effect as acts of our own. This authorization expires on May 23,2015. This is to advise that we are in full compliance with the Anti-Drug Abuse Act. We, Heddolf Products Ltd., are not subject to a denial of federal benefits pursuant to Section 5301 of the Anti-Drug Act of 1988, 21 USC853a, and no party to the application is subject to a denial of federal benefits pursuant to that section. Sincerely, Heddolf Products Ltd. .................................................................................... Signature: Ho Pan.Chan/ Electronic Engineer .................................................................................... Typed name and Title

Model X219-1 - Appearance View Model X219-2 - Appearance View Model X219-1 & X219-2 - Appearance View

FCC Label Location for model: X219-1 & X219-2 The Label must not be a stick-on paper. The Label on these products must be permanently affixed to the product and readily visible at the time of purchase and must last the expected lifetime of the equipment not be readily detachable. FCC ID: XAB-HEDDI-X219 This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

FCC Label Sample for model: X219-1 & X219-2 FCC ID: XAB-HEDDI-X219 This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Model X219-1- Internal View ANT Model X219-2- Internal View ANT

X- 219- 1 Operational Description The EUT is Remote Controller. Power input: DC3V by Battery. RF Modulation：ASK（IC MICR-F113). The transmitter consists of oscillator (13.56MHz), integrated circuit (to amplify the signal) and encoder. The oscillator generates the 433.92 MHz frequency. The encoder generates rolling code. Selectable Tact switches to avoid the interference from the same kind of transmitter. The rolling code is then transmitted to the antenna by the integrated circuit(IC). Frequency Error: The frequency error is controlled by the oscillator. Output Power Test: The transmitter output is connected to the spectrum analyzer; the output power is monitored and then adjusted. Once the procedure is finished the resistor is not adjustable by end users.

ABCD DCBA Title Number Revision Size A4 Date: 14-May-2014 Sheet of File: E:\Tony\Remote controller\220_219 Series\SAPP-S220V01-V10.DDB Drawn By: Q1A UMD22N R R R R7470R LED1RED C3 20pF C10104 C1210P C1110uF C420pF L2 82nH L1 680nH XT1 13.56MHz C13NC C144.7pF PAOUT 1 VSS 2 VDD 3 XTLOUT 4 XTLIN 5 ASK 6 IC2MICRF113 C1710uF 3.0V 3.0V Data_out 3.0V Data_out C16104 BT1 CR2032 3V R610K SW4 R DATA S0 1 S1 2 S2 3 S3 4 VSS 5 DATA 6 LED 7 VDD 8 IC1 HCS300_SOP8 Q1B R44.7K D3LL4148 R70R X219 -1 CLK C810uF C6104 C151000pF ANTENNA PCB 1 2 34 ABCD 4 3 2 1 D CBA Title Number Revision Size A4 Date: 14-May-2014 Sheet of File: E:\Tony\Remote controller\220_219 Series\SAPP-S220V01-V10.DDB Drawn By: SW2 SW3 Q1A UMD22N R R R R54.7k R7470R LED1Red C3 20pF C10104P C1210P C112.2uF C420pF L2 82nH~150nH L1 680nH XT2 13.56MHz C13NC C14 2.7pF~6.8pF PAOUT 1 VSS 2 VDD 3 XTLOUT 4 XTLIN 5 ASK 6 IC2MICRF113 3.0V 3.0V Data_out 3.0V Data_out BT1 CR2032 3V R610K R CLOCK DATA S0 1 S1 2 S2 3 S3 4 VSS 5 DATA 6 LED 7 VDD 8 IC1 HCS300_SOP8 Q1B R44.7K D1LL4148 D3LL4148 R70R C1710uF C16104 C810uF C6104 X219-2 ANTENNA PCB C15 1000pF

Waltek Services (Shenzhen) Co.,Ltd. http://www.waltek.com.cn Page 1 of 27 TEST REPORT Reference No. .................... : WTD14S0513977E FCC ID ................................ : XAB-HEDDI-X219 Applicant ............................ : Heddolf Products Ltd. Address .............................. : Unit 7, 22/F., Futura Plaza,111-113 How Ming Street Kowloon Hong Kong Manufacturer .................... : SAP Products Limited Address .............................. : Xian Sha No.2 Industrial Zone,Gao Bu Town,Dongguan City,Guangdong Province,PRC Product Name .................... : Remote Controller Model No. ........................... : X219-1, X219-2 Standards........................... : FCC CFR47 Part 15 Section 15.231: 2012 Date of Receipt sample .... : Jun.12, 2014 Date of Test ....................... : Jun.12~19, 2014 Date of Issue ...................... : Jun.23, 2014 Test Result ......................... : Pass * Remarks: The results shown in this test report refer only to the sample(s) tested, this test report cannot be reproduced, except in full, without prior written permission of the company. The report would be invalid without specific stamp of test institute and the signatures of compiler and approver. Prepared By: Waltek Services (Shenzhen) Co., Ltd. Address: 1/F., Fukangtai Building, West Baima Road, Songgang Street, Baoan District, Shenzhen, Guangdong, China Testing location: 1/F., Fukangtai Building, West Baima Road, Songgang Street, Baoan District, Shenzhen, Guangdong, China Tel :+86-755-83551033 Fax:+86-755-83552400 Compiled by: Approved by: Zero Zhou / Project Engineer Philo Zhong / Manager Reference No.: WTD14S0513977E Page 2 of 27 Waltek Services (Shenzhen) Co.,Ltd. http://www.waltek.com.cn Page 2 of 27 2 Test Summary Test Items Test Requirement Result Conducted Emissions 15.207 N/A Radiated Spurious Emissions 15.205(a) 15.209 15.231(a) PASS Periodic Operation 15.231(a) PASS 20dB Bandwidth 15.231(c) PASS Antenna Requirement 15.203 PASS Reference No.: WTD14S0513977E Page 3 of 27 Waltek Services (Shenzhen) Co.,Ltd. http://www.waltek.com.cn 3 Contents Page 1 COVER PAGE ...................................................................................................................................... 1 2 TEST SUMMARY ............................................................................................................................................. 2 3 CONTENTS ....................................................................................................................................................... 3 4 GENERAL INFORMATION ............................................................................................................................. 4 4.1 GENERAL DESCRIPTION OF E.U.T. ....................................................................................................... 4 4.2 DETAILS OF E.U.T. ................................................................................................................................ 4 4.3 TEST FACILITY ....................................................................................................................................... 4 5 EQUIPMENT USED DURING TEST ............................................................................................................. 5 5.1 EQUIPMENTS LIST ................................................................................................................................. 5 5.2 MEASUREMENT UNCERTAINTY .............................................................................................................. 5 5.3 TEST EQUIPMENT CALIBRATION ........................................................................................................... 5 6 CONDUCTED EMISSION ............................................................................................................................... 6 7 RADIATED SPURIOUS EMISSIONS ............................................................................................................ 7 7.1 EUT OPERATION ................................................................................................................................... 7 7.2 TEST SETUP .......................................................................................................................................... 8 7.3 SPECTRUM ANALYZER SETUP .............................................................................................................. 9 7.4 TEST PROCEDURE ............................................................................................................................... 10 7.5 SUMMARY OF TEST RESULTS ............................................................................................................. 11 8 PERIODIC OPERATION ............................................................................................................................... 13 9 20DB BANDWIDTH ....................................................................................................................................... 15 9.1 TEST PROCEDURE ............................................................................................................................... 15 9.2 TEST RESULT ...................................................................................................................................... 15 10 ANTENNA REQUIREMENT ......................................................................................................................... 16 11 MODEL X219-1PHOTOGRAPHS OF TESTING ....................................................................................... 17 11.1 RADIATION EMISSION TEST SETUP ..................................................................................................... 17 12 PHOTOGRAPHS - CONSTRUCTIONAL DETAILS ................................................................................. 19 12.1 MODEL X219-1 - APPEARANCE VIEW ......................…

Text truncated - open the document above for the full version.

Model X219-1Photographs of Testing Radiation Emission Test Setup From 13.56MHz to 30MHz From 30MHz to 1GHz From 1GHz to 5GHz