XAB-HEDDI-X220REMOTE CONTROLLER

User manual FCC NOTE: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:(1)this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV INTERFERENCE CAUSED BY UNAUTHORIZED MODIFICATIONS OR CHANGE TO THIS EQUIPMENT. SUCH MODIFICATIONS OR CHANGE COULD VOID THE USER’S AUTHORITY TO OPERATE THE EQUIPMENT. INSTRUCTIONS FOR RADIO CONTROL OPERATOR SINGLE ENTRY TRANSMITTER MODEL NO.:X220-3 Read the following instructions thoroughly before using transmitter. 1.Remove the transmitter cover Remove the access cover from the front of the transmitter by sliding the cover away from the top of the transmitter(Figure A).this will expose the battery . In order to facilitate the replacement of the battery. 2.The transmitter is rolling code encoding and transmitting, it will automatically and receiver code matching. FIGURE A FIGURE B Button batteries If the receiver successfully decoded, the receiver will normally work. User can click the push button,A signal tramsit out.

1 2 34 ABCD 4 3 2 1 D CBA Title Number Revision Size A4 Date: 30-Jun-2014 Sheet of File: E:\lu\RF Products\P220 Old Remote C ontroller Info\P220 Remote Controll.DDB Drawn By: BLOCK DIAGRAMROLLING CODE CHIP RF CHIP MICRF113 HCS300/HCS301 PCB ANTENNA DATA OUTPUT X2 20 -1 BLOCK DIAGRAM DC 3V By Battery 13.56MHz

Heddolf Products Ltd. FCC ID: XAB-HEDDI-X220 POWER OF ATTORNEY Date: May 24,2014 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 To Whom It May Concern: We, the undersigned, hereby authorize Waltek Services (ShenZhen) Co., Ltd. (Philo Zhong) on our behalf, to apply to the Federal Communications Commission on our equipment. Any and all acts carried out by Waltek Services (ShenZhen) Co., Ltd. (Philo Zhong) on our behalf shall have the same effect as acts of our own. This authorization expires on May 23,2015. This is to advise that we are in full compliance with the Anti-Drug Abuse Act. We, Heddolf Products Ltd., are not subject to a denial of federal benefits pursuant to Section 5301 of the Anti-Drug Act of 1988, 21 USC853a, and no party to the application is subject to a denial of federal benefits pursuant to that section. Sincerely, Heddolf Products Ltd. ......... ........................................................................... Signature: Ho Pan.Chan/ Electronic Engineer .................................................................................... Typed name and Title

Model X220-1 - Appearance View Model X220-2 - Appearance View Model X220-3 - Appearance View Model X220-1 & X220-2& X220-3 - Appearance View

FCC Label Location for model: X220-1 & X220-2& X220-3 The Label must not be a stick-on paper. The Label on these products must be permanently affixed to the product and readily visible at the time of purchase and must last the expected lifetime of the equipment not be readily detachable. FCC ID: XAB-HEDDI-X220 This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

FCC Label Sample for model: X220-1 & X220-2& X220-3 FCC ID: XAB-HEDDI-X220 This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Model X220-1- Internal View ANT Model X220-2- Internal View ANT Model X220-3- Internal View ANT

X-220- 1 Operational Description The EUT is Remote Controller. Power input: DC3V by Battery. RF Modulation：ASK（IC MICR-F113). The transmitter consists of oscillator (13.56MHz), integrated circuit (to amplify the signal) and encoder. The oscillator generates the 433.92 MHz frequency. The encoder generates rolling code. Selectable Tact switches to avoid the interference from the same kind of transmitter. The rolling code is then transmitted to the antenna by the integrated circuit(IC). Frequency Error: The frequency error is controlled by the oscillator. Output Power Test: The transmitter output is connected to the spectrum analyzer; the output power is monitored and then adjusted. Once the procedure is finished the resistor is not adjustable by end users.

1 2 34 ABCD 4 3 2 1 D CBA Title Number Revision Size A4 Date: 14-May-2014 Sheet of File: E:\Tony\Remote controller\220_219 Series\SAPP-S220V01-V10.DDB Drawn By: SW4NC SW2 SW3 Q1A UMD22N R R R C7 104 R33.3K R7220R LED1Red 5mm C3 20pF C10102 C1210pF C11104 C420pF L2 82nH~150nH L1 680nH XT1 13.56MHz C13NC C14 2.7pF~6.8pF PAOUT 1 VSS 2 VDD 3 XTLOUT 4 XTLIN 5 ASK 6 IC2MICRF113 C510uF 3V 3V Data_out 3V Data_out C6104 BT1 CR2032 3V R647K SW1 R CLOCK DATA S0 1 S1 2 S2 3 S3 4 VSS 5 DATA 6 LED 7 VDD 8 IC1 HCS300_SOP8 Q1B R4NC R13.3K R23.3K D1BAT54C D2BAT54C R50R C1104 C1010uF ANTENNA PCB C151000pF * * * * * * * X220 Series TX_Sch Remark: Model NO.X220-1:SW1/SW3/SW4/R1/R3/R4 D2 for NC.Model NO.X220-2:SW2/SW4/R2/R4 for NC.Model NO.X220-3:SW4/R4 for NC.

Waltek Services (Shenzhen) Co.,Ltd. http://www.waltek.com.cn Page 1 of 29 TEST REPORT Reference No. .................... : WTD14S0514162E FCC ID ................................ : XAB-HEDDI-X220 Applicant ............................ : Heddolf Products Limited Address .............................. : Unit 7, 22/F., Futura Plaza,111-113 How Ming Street, Kwun Tong, Kowloon, Hong Kong, PRC Manufacturer .................... : SAP Products Limited Address .............................. : Xian Sha No.2 Industrial Zone,Gao Bu Town,Dongg uan City, Guan gdong Province, PRC Product Name .................... : Remote Controller Model No. ........................... : X220-1, X220-2, X220-3 Standards........................... : FCC CFR47 Part 15 Section 15.231: 2012 Date of Receipt sample .... : Jun.12, 2014 Date of Test ....................... : Jun.15~19, 2014 Date of Issue ...................... : Jun.23, 2014 Test Result ......................... : Pass * Remarks: The results shown in this test report refer only to the sample(s) tested, this test report cannot be reproduced, except in full, without prior written permission of the company. The report would be invalid without specific stamp of test institute and the signatures of compiler and approver. Prepared By: Waltek Services (Shenzhen) Co., Ltd. Address: 1/F., Fukangtai Building, West Baima Road, Songgang Street, Baoan District, Shenzhen, Guangdong, China Testing location: 1/F., Fukangtai Building, West Baima Road, Songgang Street, Baoan District, Shenzhen, Guangdong, China Tel :+86-755-83551033 Fax:+86-755-83552400 Compiled by: Approved by: Zero Zhou / Project Engineer Philo Zhong / Manager Reference No.: WTD14S0514162E Page 2 of 29 Waltek Services (Shenzhen) Co.,Ltd. http://www.waltek.com.cn Page 2 of 29 2 Test Summary Test Items Test Requirement Result Conducted Emissions 15.207 N/A Radiated Spurious Emissions 15.205(a) 15.209 15.231(a) PASS Periodic Operation 15.231(a) PASS 20dB Bandwidth 15.231(c) PASS Antenna Requirement 15.203 PASS Reference No.: WTD14S0514162E Page 3 of 29 Waltek Services (Shenzhen) Co.,Ltd. http://www.waltek.com.cn 3 Contents Page 1 COVER PAGE ...................................................................................................................................... 1 2 TEST SUMMARY ............................................................................................................................................. 2 3 CONTENTS ....................................................................................................................................................... 3 4 GENERAL INFORMATION ............................................................................................................................. 4 4.1 GENERAL DESCRIPTION OF E.U.T. ....................................................................................................... 4 4.2 DETAILS OF E.U.T. ................................................................................................................................ 4 4.3 TEST FACILITY ....................................................................................................................................... 4 5 EQUIPMENT USED DURING TEST ............................................................................................................. 5 5.1 EQUIPMENTS LIST ................................................................................................................................. 5 5.2 MEASUREMENT UNCERTAINTY .............................................................................................................. 5 5.3 TEST EQUIPMENT CALIBRATION ........................................................................................................... 5 6 CONDUCTED EMISSION ............................................................................................................................... 6 7 RADIATED SPURIOUS EMISSIONS ............................................................................................................ 7 7.1 EUT OPERATION ................................................................................................................................... 7 7.2 TEST SETUP .......................................................................................................................................... 8 7.3 SPECTRUM ANALYZER SETUP .............................................................................................................. 9 7.4 TEST PROCEDURE ............................................................................................................................... 10 7.5 SUMMARY OF TEST RESULTS ............................................................................................................. 11 8 PERIODIC OPERATION ............................................................................................................................... 13 9 20DB BANDWIDTH ....................................................................................................................................... 15 9.1 TEST PROCEDURE ............................................................................................................................... 15 9.2 TEST RESULT ...................................................................................................................................... 15 10 ANTENNA REQUIREMENT ......................................................................................................................... 16 11 MODEL X220-1 PHOTOGRAPHS OF TESTING ...................................................................................... 17 11.1 RADIATION EMISSION TEST SETUP ..................................................................................................... 17 12 PHOTOGRAPHS - CONSTRUCTIONAL DETAILS ................................................................................. 19 12.1 MODEL X220-1 - APPEA…

Text truncated - open the document above for the full version.

Model X220-1Photographs of Testing Radiation Emission Test Setup From 13.56MHz to 30MHz From 30MHz to 1GHz From 1GHz to 5GHz