XBD-FM4FM TRANSMITTER

+ Hold to turn ON + + + + + ISFM31 Caution : Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. FCC Compliance Statement: This device is verified to comply with Part 15 of the FCC Rules. Operation subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. JamKast TM Universal Digital FM Transmitter with dTECT TM Technology Instructions 12Volt Outlet OPTIONAL AUTOSCANNING The JamKast™ transmitter uses dTECT™ technology to locate and lock-in the four best radio frequencies for iPod or iPhone playback. NOTE: We recommend activating dTECT™ Autoscanning when entering new areas while you travel. SELECTING PRESETS Use arrow buttons to choose PRESET that offers best performance MANUALLY SAVE PRESETS The JamKast™ iP transmitter allows you to manually save your preferred station on the PRESET 1. Hold both at the same time to activate scanning (dTECT ™) 2. PRESETS will blink for 20 sec. while scanning Press to move up 3. Scanning is complete when PRESETS stops blinking 2. Hold once to enter manual tuning mode 4. Press once to save 1. Choose the PRESET you want to save 3. Tune to the desired frequency Press to move down MANUALLY SET ANY FREQUENCY You can choose any frequency 1) Press once to enter manual tuning mode 3. DONE (manual tuning mode will remain active for 30 sec.) 2) Tune to desired frequency 45 CONNECT Plug the JamKast™ iP transmitter into the docking port on your iPod or iPhone. The JamKast™ iP will automatically Turn On when you press any button. CONNECT Insert the 3.5mm input into the headphone jack on your MP3 player, smartphone or other portable device. 1 PLUG-IN Plug the power input into the lighter port on your vehicle’s dashboard or center console. 2 TURN ON Press to turn JamKast™ 3 NOTE: some smartphones feature 2.5mm headphone inputs. If this is the case, you will require an input adaptor to use this product. + MP 3 pl ayers • Apple iPod (all models) • Microsoft Zune (all models) • Creative Zen / MuVo • iRiver Spinn / E100 / Clix • Sony E / S / X Series Walkman • Toshiba Gigabeat • SanDisk Sansa • Samsung P2 / Q2 / U5 • Archos 5 / 7 Media Tablet WOR KS WIT H The JamKast™ wor ks with a wide var iet y of toda y’s most popular por table media players , including: Smart Pho nes* • Apple iPhone • Blackberry • Palm Pre & Trio • LG Dare & Incite • Samsung Instinct • Nokia N95 & N97 Othe r Med ia Devices • CD or DVD players • Portable televisions • Laptop c omputers • Portable HD Radio tuners • GPS systems • Handheld gaming systems iSimple® A Division of AAMP of America™ 13190 56th Court Clearwater , FL 33760 Ph. 866-788-4237 [email protected] om ©2009 AAMP of Florida, Inc . www.isimplesolutions. co m PL AY To begin enjo ying music using your JamKast™, tune your car radio to the fr equency sho wn on the digital LCD display and pr ess pla y on your por table media devic e. It’s just that simple! � *S ome smartphones fea tur e 2.5mm headphone inputs. I f this is the case , y ou will require an input adaptor t o use this product. Optimal distance: <10 ft. Preset memory: 4 FM stations Scr een: white numeric L CD Frequency r esp onse: 50Hz-15000Hz Transmission range: 88.1MHz-107.9MHz Separ ation: > 35dB Op er ating curren t : 18.8+/- 3mA Power : DC 5V Power : iP hone , iP od and mini-USB Optimal distance : <10feet Op er ating Range: up to 30 feet Weigh t: < 17 gr. SPECIFICATION S Warranty On e Year Limi ted War ranty The quali ty controls us ed in th e m anufactu re of this p roduct will e nsure your satisfaction . This warranty applies only to the original purchaser of this produ ct f rom an au thorized i Simple® dea ler. Thi s warr anty cover s any su pp li ed or manu factu red pa rts of this produ ct that, upon ins pecti on by iSimple® auth orized personnel, is found to have failed in normal us e due to de fects in material or work ma nshi p. This warranty does not app ly to in stal latio n expens es. Attempt ing to se rvi ce or modify this uni t, operating this unit under conditions other than the recom men ded voltage wi ll ren der this WAR RAN TY VOI D. Unless ot herwise pres cribed by law, iSimple® sh all not be liable for any per so nal inju ry, property da mage and or any inci denta l or consequentia l damages of any kind (in cludi ng water dam age) res ul ti ng f rom m alfu nction s, defects, m isu se, imp roper i nstal lation o r a lteration of this product. All parts of this iSimple® produ ct a re g uaranteed for a period of 1 year as foll ows: Wi th in the first 12 months from date of purcha se, subject to the condit ions above, iS imple® will repai r or repla ce the produ ct at our disc ret ion , if it is de fective in material or workmans hip provi ding it is returned to a n Auth orized iSim ple TM de al er, w ith PROO F O F PU RCHA SE f rom a n a uth orized iSi mple ® dea ler. Warn ing : This equipment may be reset by unintenti onal e lectrostatic dis cha rge d uring o perati on. E xposu re to di rect sunlig ht o r extreme heat m ay cause damage or m alfu ncti on. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However,there is no guarantee that interference will not occur in a particular installation.If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the foll…

Text truncated - open the document above for the full version.

1) How does this device operate? Response: 1 Plug into IPod or similar device and 12Vdc battery Outlet. 2 Press on the power key for a few seconds, then the EUT LED screen display the default frequency. 3 Press the “+” /“-“ to tune FM frequency, then select applicable transmit channel(88.1 MHZ,98.1 MHZ,107.9MHZ). 4 Play the IPod or similar device, then tune the IPod volume to maximum. 5 The Music/Audio will be transmitted from FM19V2 system. 2) Provide information on the device and its antenna. Response: AAMP of Florida,dba AAMP of America use (1.7cm*0.5cm ) 12uh inductance adding 4cm power cable as antenna 3) How is it installed? Response: The EUT will direct plug into IPod or similar device connector and 12Vdc new battery outlet. 4) What test procedure was used? Response: 1. Plug into IPod and New battery were installed in the equipment under test for radiated emissions test. 2. Setup the EUT according ANSI C63.4:2009 3.This is a handhold device,The radiation emission should be tested under 3-axes(X,Y,Z) position(X denotes lying on the table,Y denotes side stand and Z denotes vertical stand) 4.Maximizing procedure was performed on the six (6) highest emissions in worst mode to ensure EUT is compliant with installation combinations 5. All data was recorded in the peak and average detection mode for fundamental frequencies and harmonic and spurious frequencies. 6. The EUT was under FM Transmit modulation with signals mode during the final qualification test and the configuration was used to represent the worst case results. 5) If tested in a car, how was it configured/tested? Response: The tested not in a car, Test in 3m Chamber of Waltek Service (Shenzhen) Co., Ltd. EMC Laboratory. The test performed at the lab located in 1/F, Fukangtai Building,West Baima Rd.,Songgang Street, Bao’an District, Shenzhen 518105, Guangdong,China. The lab Registration No is 880581 The test method is ANSI C63.4:2009. 6) Was the tuning range properly verified? Response: The test lab should indicate in the report that the tuning controls were manually adjusted to verify maximum tuning range. EUT was adjusted to work at the selected channels: 88.1 MHz, 98.1 MHz,and 107.9 MHz. The EUT will not allow operation below 88.1 MHz and will not allow operation above 107.9 MHz. 7) Was the bandwidth properly tested with maximum audio input? Response: Emissions from the intentional radiator shall be confined within a band 200 kHz wide centered on the operation frequency. The 200 kHz band shall lie wholly within the frequency range of 88 –108 MHz. test was under the module of audio input, the device audio input source from maximum audio input 8) Provide the test report. Response: Please refer the FCC ID:XBD-FM4 test report

AAMP of Flordia,dba AAMP of America 13160 56th court clearwatcr Florida United States FCC ID: XBD-FM4 AGENCY AUTHORIZATION LETTER January 26,2010 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 To Whom It May Concern: We, the undersigned, hereby authorize Waltek Services (ShenZhen) Co., Ltd. (Philo Zhong) on our behalf, to apply to the Federal Communications Commission on our equipment. Any and all acts carried out by Waltek Services (ShenZhen) Co., Ltd. (Philo Zhong) on our behalf shall have the same effect as acts of our own. This authorization expires on Sep 15, 2010. This is to advise that we are in full compliance with the Anti-Drug Abuse Act. We, AAMP of Flordia,dba AAMP Of America., are not subject to a denial of federal benefits pursuant to Section 5301 of the Anti-Drug Act of 1988, 21 USC853a, and no party to the application is subject to a denial of federal benefits pursuant to that section. Sincerely, AAMP of Flordia,dba AAMP Of America ------------------------------- Eric Leclerc Engineer Product Development

EUT-Front View EUT-Back View

AAMP of Flordia,dba AAMP of America FCC ID:XBD-FM4 FCC ID Label This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation The Label must not be a stick-on paper. The Label on these products must be permanently affixed to the product and readily visible at the time of purchase and must last the expected lifetime of the equipment not be readily detachable. Proposed Label Location on EUT EUT Bottom View/proposed FCC Mark Location FCC ID:XBD-FM4 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation

Model Name: FM19V2 Made in China FCC ID: XBD-FM4 This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

PCB-Front View(1) PCB-Back View(1) Ant. Ant. PCB-Front View(2) PCB-Back View(2)

AAMP of Flordia,dba AAMP of America FCC ID: XBD-FM4 FCC TEST REPORT Page 1 of 24 FCC ID : XBD-FM4 Applicant : AAMP of Flordia, dba AAMP of America Address : 13160 56th court Clearwater Florida United States Equipment Under Test (EUT) : Product description : FM Transmitter Model No. : ISFM31,FM3,FM19,FM19V2 Standards : FCC 15 Paragraph 15.239 Date of Test : January 28~February 2,2010 Project Engineer : Forrest Lei Reviewed By : Prepared By: Waltek Services (Shenzhen) Co., Ltd. 1/F, Fukangtai Building, West Baima Rd., Songgang Street, Baoan District, Shenzhen 518105, China Tel :+86-755-27553488 Fax:+86-755-27553868 AAMP of Flordia,dba AAMP of America FCC ID: XBD-FM4 Page 2 of 24 2 Contents Page 1 COVER PAGE ......................................................................................................................................................... 1 2 CONTENTS .............................................................................................................................................................. 2 3 TEST SUMMARY ................................................................................................................................................... 3 4 GENERAL INFORMATION.................................................................................................................................. 4 4.1 CLIENT INFORMATION........................................................................................................................................ 4 4.2 GENERAL DESCRIPTION OF E.U.T....................................................................................................................... 4 4.3 DETAILS OF E.U.T. ............................................................................................................................................. 4 4.4 DESCRIPTION OF SUPPORT UNITS....................................................................................................................... 4 4.5 STANDARDS APPLICABLE FOR TESTING.............................................................................................................. 4 4.6 TEST FACILITY.................................................................................................................................................... 5 4.7 TEST LOCATION.................................................................................................................................................. 5 5 EQUIPMENT USED DURING TEST ................................................................................................................... 6 6 RADIATION EMISSION TEST............................................................................................................................. 9 6.1 TEST EQUIPMENT................................................................................................................................................ 9 6.2 MEASUREMENT UNCERTAINTY........................................................................................................................... 9 6.3 TEST PROCEDURE............................................................................................................................................. 10 6.4 RADIATED TEST SETUP..................................................................................................................................... 10 6.5 SPECTRUM ANALYZER SETUP........................................................................................................................... 11 6.6 CORRECTED AMPLITUDE & MARGIN CALCULATION........................................................................................ 11 6.7 SUMMARY OF TEST RESULTS............................................................................................................................ 11 6.8 EUT OPERATING CONDITION........................................................................................................................... 12 6.9 RADIATED EMISSIONS LIMIT............................................................................................................................ 12 6.10 RADIATED EMISSIONS TEST RESULT................................................................................................................ 13 7 BAND EDGE .......................................................................................................................................................... 17 7.1 TEST EQUIPMENT.............................................................................................................................................. 17 7.2 TEST PROCEDURE............................................................................................................................................. 17 7.3 BAND EDGE TEST RESULT................................................................................................................................18 8 ANTENNA REQUIREMENT............................................................................................................................... 20 8.1 STANDARD REQUIREMENT................................................................................................................................20 8.2 RESULT............................................................................................................................................................. 20 9 PHOTOGRAPHS - CONSTRUCTIONAL DETAILS ....................................................................................... 21 9.1 EUT-TOP VIEW................................................................................................................................................ 21 9.2 EUT-BOTTOM VIEW......................................................................................................................................... 21 9.3 PCB1-TOP VIEW.......................................................................…

Text truncated - open the document above for the full version.

Radiation Emission Test View for 30MHZ~1000MHZ