XIA-CFW2132Outdoor LTE Router

casa systems User Guide CFW-2132 Do c No. UG01228 2 of 63 CFW-2132 – User Guide UG01228 v1.0 April 27, 2020 © Casa Systems 2020 Important notice This device, like any wireless device, operates using radio signals which cannot guarantee the transmission and reception of data in all conditions. While the delay or loss of signal is rare, you should not rely solely on any wireless device for emergency communications or otherwise use the device in situations where the interruption of data connectivity could lead to death, personal injury, property damage, data loss, or other loss. Casa Systems accepts no responsibility for any loss or damage resulting from errors or delays in transmission or reception, or the failure of the Casa Systems CFW-2132 to transmit or receive such data. Safety and hazards Warning – Do not connect or disconnect cables or devices to or from the USB port, SIM card tray, or Ethernet port in hazardous locations such as those in which flammable gases or vapours may be present, but normally are confined within closed systems; are prevented from accumulating by adequate ventilation; or the location is adjacent to a location from which ignitable concentrations might occasionally be communicated. Copyright Copyright© 2020 Casa Systems. All rights reserved. The information contained herein is proprietary to Casa Systems. No part of this document may be translated, transcribed, reproduced, in any form, or by any means without prior written consent of Casa Systems. Trademarks and registered trademarks are the property of Casa Systems or their respective owners. Specifications are subject to change without notice. Images shown may vary slightly from the actual product. Note – This document is subject to change without notice. Document history This document relates to the following product: CFW-2132 antenna Ver. Document description Date v1.0 First release April 27, 2020 Table i. – Document revision history 3 of 63 CFW-2132 – User Guide UG01228 v1.0 April 27, 2020 © Casa Systems 2020 Contents Overview ..................................................................................................................................... 6 Introduction ....................................................................................................................................................................................................... 6 Target audience ................................................................................................................................................................................................ 6 Prerequisites ..................................................................................................................................................................................................... 6 Notation ...................................................................................................................................................................................................... 6 Product introduction ....................................................................................................................... 7 Product overview .............................................................................................................................................................................................. 7 Package contents .............................................................................................................................................................................................. 7 Physical dimensions and interfaces ..................................................................................................... 8 Physical dimensions ......................................................................................................................................................................................... 8 Interfaces ........................................................................................................................................................................................................... 9 Insert SIM card .................................................................................................................................................................................................. 9 Assemble and attach the mounting bracket ................................................................................................................................................ 13 Overview of completed mounting .......................................................................................................................................................... 13 Mounting bracket assembly instructions .............................................................................................................................................. 14 Power the CFW ................................................................................................................................................................................................ 16 R45 cable weather seal assembly ........................................................................................................................................................... 16 PoE-03 power supply ............................................................................................................................................................................... 20 PoE-03 LED indicators ................................................................................................................................................................................................................... 20 Installation ................................................................................................................................. 21 Typical CFW antenna installation ....................................................…

Text truncated - open the document above for the full version.

pcbauthletter_170808 NetComm Wireless Limited 18-20 Orion Road, Lane Cove NSW 2066 AUSTRALIA Date: 1 st May 2020 PCTEST Certification Body 7185 Oakland Mills Road Columbia, MD 21046 RE: Authorization Letter for FCC ID: XIA- CFW2132 To whom it may concern: We, the undersigned, hereby authorize PCTEST Engineering Laboratory, Inc. , to act on our behalf in all matters relating to applications for equipment authorization, including the signing of all documents relating to these matters. All acts carried out by PCTEST Engineering Laboratory, Inc. on our behalf shall have the same effect as acts of our own. We also hereby certify that no party to this application is subject to a denial of benefits, including FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S. C. 862. Sincerely, Signature NAME: Pat Sinni TITLE: Senior Compliance Specialist Engineer COMPANY: NetComm Wireless Limited

Long Term Confidential Letter Date: 1 st May 2020 Federal Communications Commission 7435 Oakland Mills Road Columbia MD 21046 Subject: Request for Confidentiality FCC ID：XIA-CFW2132 To Whom It May Concern: Long Term Confidentiality Pursuant to Sections 0.457 and 0.459 of the Commission’s Rules, we hereby respectfully request confidential treatment of information accompanying this application as outlined below: ● Block Diagrams ● Schematics ● Operational Description ● Part List ● Tune-up procedure The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the Applicant and provide unjustified benefits to its competitors. We understand that pursuant to Rule 0.457, disclosure of this Application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely, Applicant’s company name : NetComm Wireless Limited Applicant’s company address : 18-20 Orion Road Lane Cove NSW 2066 Australia Signature : Name : Pat Sinni E-Mail : [email protected] Tel : +61294242070 Fax : +61294242070 Short Term Confidential Letter Date: 1 st May 2020 Federal Communications Commission 7435 Oakland Mills Road Columbia MD 21046 Subject: Request for Confidentiality FCC ID：XIA-CFW2132 To Whom It May Concern: Short Term Confidentiality Pursuant to Sections 0.457 and 0.459 of the Commission’s Rules, we hereby respectfully request short term confidential treatment for the following information for an initial period of 180 days in order to ensure sensitive business information remains confidential until the actual marketing of the device: • External photos • Test Setup photos • User’s manual • Internal Photos Sincerely, Applicant’s company name : NetComm Wireless Limited Applicant’s company address : 18-20 Orion Road Lane Cove NSW 2066 Australia Signature : Name : Pat Sinni E-Mail : [email protected] Tel : +61294242070 Fax : +61294242070

Netcomm Wireless Limited FCC ID: XIA-CFW2132 Model: CFW-2132 External Photos EUT Type: Outdoor LTE Router Page 1 of 2 © 2020 PCTEST V 9.0 02/01/2019 E X T E R N A L P H O T O G R A P H S Netcomm Wireless Limited FCC ID: XIA-CFW2132 Model: CFW-2132 External Photos EUT Type: Outdoor LTE Router Page 2 of 2 © 2020 PCTEST V 9.0 02/01/2019 3. Label Location

Description of Label affixed to CFW-2132 Device 1. Label sample (size 126mm x 25mm) 2. Label Mechanical Construction and Affixment The labels are constructed from PC9821W material and the information is laser etched into the label. The label is affixed to the exterior of the CFW-2132 housing using 3M VHB Adhesive Transfer Tape. VHB adhesive transfer tape is appropriate for use in interior and exterior industrial applications to replace rivets, spot welds, liquid adhesives, and other permanent fasteners. The label is Affixed at device manufacture and is on the exterior of the housing. Labels on the outside of the carton contain the device model and FCC ID where it is available to the purchaser at the time of purchase.

Netcomm Wireless Limited FCC ID: XIA-CFW2132 Model: CFW-2132 Internal Photos EUT Type: Outdoor LTE Router Page 1 of 5 © 2020 PCTEST V 9.0 02/01/2019 I N T E R N A L P H O T O G R A P H S Netcomm Wireless Limited FCC ID: XIA-CFW2132 Model: CFW-2132 Internal Photos EUT Type: Outdoor LTE Router Page 2 of 5 © 2020 PCTEST V 9.0 02/01/2019 Netcomm Wireless Limited FCC ID: XIA-CFW2132 Model: CFW-2132 Internal Photos EUT Type: Outdoor LTE Router Page 3 of 5 © 2020 PCTEST V 9.0 02/01/2019 Netcomm Wireless Limited FCC ID: XIA-CFW2132 Model: CFW-2132 Internal Photos EUT Type: Outdoor LTE Router Page 4 of 5 © 2020 PCTEST V 9.0 02/01/2019 Netcomm Wireless Limited FCC ID: XIA-CFW2132 Model: CFW-2132 Internal Photos EUT Type: Outdoor LTE Router Page 5 of 5 © 2020 PCTEST V 9.0 02/01/2019

FCC ID: XIA-CFW2132 MAXIMUM PERMISSIBLE EXPOSURE REPORT Approved by: Quality Manager Test Report S/N: Test Dates: EUT Type: Page 1 of 7 1M2003310053-05-R1.XIA 3/31 - 5/15/2020 Outdoor LTE Router © 2020 PCTEST V 9.0 02/01/2019 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact [email protected]. Applicant Name: Netcomm Wireless Limited 18-20 Orion Road Lane Cove NSW 2066 Sydney Austrailia Date of Testing: 3/31 - 5/15/2020 Test Site/Location: PCTEST Lab. Columbia, MD, USA Test Report Serial No.: 1M2003310053-05-R1.XIA FCC ID: XIA-CFW2132 APPLICANT: Netcomm Wireless Limited EUT Type: Outdoor LTE Router Model: CFW-2132 FCC Classification: Citizens Band Category A and B Devices (CBD) FCC Rule Part: FCC Part 1 (§1.1310) and Part 2 (§2.1091) Test Procedure(s): KDB 447498 D01 This revised Test Report (S/N: 1M2003310053-05-R1.XIA) supersedes and replaces the previously issued test report(s) on the same subject device for the same type of testing as indicated. Please discard or destroy the previously issued test report(s) and dispose of it accordingly. This equipment has been shown to be capable of compliance with the applicable technical standards as indicated in the measurement report and was tested in accordance with the measurement procedures specified in FCC KDB 447498 D01. Test results reported herein relate only to the item(s) tested. I attest to the accuracy of data. All measurements reported herein were performed by me or were made under my supervision and are correct to the best of my knowledge and belief. I assume full responsibility for the completeness of these measurements and vouch for the qualifications of all persons taking them. PCTEST 7185 Oakland Mills Road, Columbia, MD 21046 USA Tel. 410.290.6652 / Fax 410.290.6654 http://www.pctest.com RF EXPOSURE EVALUATION Maximal Permissible Exposure [MPE] FCC ID: XIA-CFW2132 MAXIMUM PERMISSIBLE EXPOSURE REPORT Approved by: Quality Manager Test Report S/N: Test Dates: EUT Type: Page 2 of 7 1M2003310053-05-R1.XIA 3/31 - 5/15/2020 Outdoor LTE Router © 2020 PCTEST V 9.0 02/01/2019 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact [email protected]. T A B L E O F C O N T E N T S 1.0 RF EXPOSURE EVALUATION – MAXIMUM PERMISSIBLE EXPOSURE (MPE) ........................ 3 1.1 Introduction ............................................................................................................................................ 3 1.2 EUT Description ..................................................................................................................................... 3 1.3 MPE Requirements Overview ................................................................................................................ 4 1.4 Procedure .............................................................................................................................................. 5 1.5 Summary of Results............................................................................................................................... 6 2.0 CONCLUSION ................................................................................................................................. 7 FCC ID: XIA-CFW2132 MAXIMUM PERMISSIBLE EXPOSURE REPORT Approved by: Quality Manager Test Report S/N: Test Dates: EUT Type: Page 3 of 7 1M2003310053-05-R1.XIA 3/31 - 5/15/2020 Outdoor LTE Router © 2020 PCTEST V 9.0 02/01/2019 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact [email protected]. 1.0 R F E X P O S U R E E V A L U A T I O N – M A X I M U M P E R M I S S I B L E E X P O S U R E ( M P E ) 1.1 Introduction This document is prepared to show compliance with the RF Exposure requirements as required in §1.1310 of the FCC Rules and Regulations and RSS-102 of Industry Canada. The limit for Maximum Permissible Exposure (MPE), specified in FCC §1.1310. According to FCC §1.1310 and RSS-102: the criteria listed in the following table shall be used to evaluate the environmental impact of human exposure to radio-frequency (RF) radiation as specified in §1.1307(b). 1.2 EUT Description The Netcomm FCC ID: XIA-C F W 2 1 3 2 is an Outdoor LTE Router that operates with a 17.5dBi gain antenna. FCC ID: XIA-CFW2132 MAXIMUM PERMISSIBLE EXPOSURE REPORT Approved by: Quality Manager Test Report S/N: Test Dates: EUT Type: Page 4 of 7 1M2003310053-05-R1.XIA 3/31 - 5/15/2020 Outdoor LTE Router © 2020 PCTEST V 9.0 02/01/2019 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact [email protected]. 1.3 MPE Requirements Overview Three different categories …

Text truncated - open the document above for the full version.

FCC ID: XIA-CFW2132 MEASUREMENT REPORT (CERTIFICATION) Approved by: Quality Manager Test Report S/N: Test Dates: EUT Type: Page 1 of 59 1M2003310053-04.XIA 4/23/2020 – 5/8/2020 Outdoor LTE Router © 2020 PCTEST V1.0 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact [email protected]. Applicant Name: Netcomm Wireless Limited 18-20 Orion Road Lane Cove NSW 2066, Sydney Austrailia Date of Testing: 4/23/2020 – 5/8/2020 Test Site/Location: PCTEST Lab. Columbia, MD, USA Test Report Serial No.: 1M2003310053-04.XIA FCC ID: XIA-CFW2132 APPLICANT: NETCOMM WIRELESS LIMITED Application Type: Certification Model: CFW-2132 EUT Type: Outdoor LTE Router Frequency Range: 3550 – 3700 MHz FCC Classification: Citizens Band Category A and B Devices (CBD) FCC Rule Part(s): Part 96 Test Procedure(s): KDB 940660 D01 v02, KDB 940660 D02 v01, WINNF-TS-0122-V1.0.0, CBRSA-TS-9001 V.1.0.0, [WINNF-19-IN-00033] CBRS CPE-CBSD as UUT Test Guidelines Version V1.0 This equipment has been shown to be capable of compliance with the applicable technical standards as indicated in the measurement report and was tested in accordance with the measurement procedures specified in the test procedures listed above. Test results reported herein relate only to the item(s) tested. I attest to the accuracy of data. All measurements reported herein were performed by me or were made under my supervision and are correct to the best of my knowledge and belief. I assume full responsibility for the completeness of these measurements and vouch for the qualifications of all persons taking them. PCTEST 7185 Oakland Mills Road, Columbia, MD 21046 USA Tel. 410.290.6652 / Fax 410.290.6654 http://www.pctest.com TEST REPORT CBSD-SAS Interoperability FCC ID: XIA-CFW2132 MEASUREMENT REPORT (CERTIFICATION) Approved by: Quality Manager Test Report S/N: Test Dates: EUT Type: Page 2 of 59 1M2003310053-04.XIA 4/23/2020 – 5/8/2020 Outdoor LTE Router © 2020 PCTEST V1.0 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact [email protected]. T A B L E O F C O N T E N T S 1.0 INTRODUCTION ...................................................................................................................................... 3 1.1 Scope ...................................................................................................................................................................... 3 1.2 PCTEST Test Location ........................................................................................................................................... 3 1.3 Test Facility / Accreditations ................................................................................................................................... 3 2.0 PRODUCT INFORMATION ..................................................................................................................... 4 2.1 Equipment Description ............................................................................................................................................ 4 2.2 Device Capabilities ................................................................................................................................................. 4 2.3 Test Configuration .................................................................................................................................................. 4 2.4 Modifications ........................................................................................................................................................... 4 3.0 TEST EQUIPMENT CALIBRATION DATA .............................................................................................. 5 4.0 ENVIRONMENTAL CONDITIONS .......................................................................................................... 6 5.0 EVALUATION PROCEDURE .................................................................................................................. 7 6.0 TEST Summary ........................................................................................................................................ 8 6.1 Summary ................................................................................................................................................................ 8 7.0 CONCLUSION ....................................................................................................................................... 10 APPENDIX A – TEST RESULT AND DATA ..................................................................................................... 11 A1 [WINNF.FT.C.REG.1] MULTI-STEP REGISTRATION ................................................................................................................. 11 A3 [WINNF.FT.C.REG.5] SINGLE-STEP REGISTRATION FOR CBSD WITH CPI SIGNED DATA ................................................ 13 A4 [WINNF.FT.C.REG.8] MISSING REQUIRED PARAMETERS (RESPONSECODE 102) ............................................................ 15 A5 [WINNF.FT.C.REG.10] PENDING REGISTRATION (RESPONSECODE 200) ........................................................................... 16 A6 [WINNF.FT.C.REG.12] INVALID PARAMETER (RESPONSECODE 103) ...................................................................…

Text truncated - open the document above for the full version.

FCC ID: XIA-CFW2132 MEASUREMENT REPORT (CERTIFICATION) Approved by: Quality Manager Test Report S/N: Test Dates: EUT Type: Page 1 of 97 1M2003310053-01-R1.XIA 3/31 - 5/15/2020 Outdoor LTE Router © 2020 PCTEST V1.0 12/17/2018 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact [email protected]. Applicant Name: Netcomm Wireless Limited 18-20 Orion Road Lane Cove NSW 2066 Sydney Austrailia Date of Testing: 3/31 - 5/15/2020 Test Site/Location: PCTEST Lab. Columbia, MD, USA Test Report Serial No.: 1M2003310053-01-R1.XIA FCC ID: XIA-CFW2132 APPLICANT: Netcomm Wireless Limited Application Type: Certification Model: CFW-2132 EUT Type: Outdoor LTE Router FCC Classification: Citizens Band Category A and B Devices (CBD) FCC Rule Part(s): 96 Test Procedure(s): ANSI C63.26-2015, ANSI/TIA-603-E-2016, KDB 971168 D01 v03r01 This revised Test Report (S/N: 1M2003310053-01-R1.XIA) supersedes and replaces the previously issued test report(s) on the same subject device for the same type of testing as indicated. Please discard or destroy the previously issued test report(s) and dispose of it accordingly. This equipment has been shown to be capable of compliance with the applicable technical standards as indicated in the measurement report and was tested in accordance with the measurement procedures specified in §2.947. Test results reported herein relate only to the item(s) tested. I attest to the accuracy of data. All measurements reported herein were performed by me or were made under my supervision and are correct to the best of my knowledge and belief. I assume full responsibility for the completeness of these measurements and vouch for the qualifications of all persons taking them. PCTEST 7185 Oakland Mills Road, Columbia, MD 21046 USA Tel. 410.290.6652 / Fax 410.290.6654 http://www.pctest.com MEASUREMENT REPORT LTE FCC ID: XIA-CFW2132 MEASUREMENT REPORT (CERTIFICATION) Approved by: Quality Manager Test Report S/N: Test Dates: EUT Type: Page 2 of 97 1M2003310053-01-R1.XIA 3/31 - 5/15/2020 Outdoor LTE Router © 2020 PCTEST V1.0 12/17/2018 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact [email protected]. T A B L E O F C O N T E N T S 1.0 INTRODUCTION ........................................................................................................................................... 4 1.1 Scope ................................................................................................................................................................. 4 1.2 PCTEST Test Location ....................................................................................................................................... 4 1.3 Test Facility / Accreditations ............................................................................................................................... 4 2.0 PRODUCT INFORMATION ........................................................................................................................... 5 2.1 Equipment Description ....................................................................................................................................... 5 2.2 Device Capabilities ............................................................................................................................................. 5 2.3 Test Configuration .............................................................................................................................................. 5 2.4 EMI Suppression Device(s)/Modifications .......................................................................................................... 5 3.0 DESCRIPTION OF TESTS ........................................................................................................................... 6 3.1 Measurement Procedure .................................................................................................................................... 6 3.2 Radiated Power and Radiated Spurious Emissions ........................................................................................... 6 4.0 MEASUREMENT UNCERTAINTY ................................................................................................................ 7 5.0 TEST EQUIPMENT CALIBRATION DATA ................................................................................................... 8 6.0 SAMPLE CALCULATIONS ........................................................................................................................... 9 7.0 TEST RESULTS .......................................................................................................................................... 10 7.1 Summary .......................................................................................................................................................... 10 7.2 Occupied Bandwidth ........................................................................................................................................ 12 7.3 Spurious and Harmonic Emissions at Antenna Terminal ................................................................................. 19 7.4 Band Edge Emissions at Antenna Terminal ...............................................................................…

Text truncated - open the document above for the full version.

FCC ID: XIA-CFW2132 MEASUREMENT REPORT (CERTIFICATION) Approved by: Quality Manager Test Report S/N: Test Dates: EUT Type: Page 68 of 97 1M2003310053-01-R1.XIA 3/31 - 5/15/2020 Outdoor LTE Router © 2020 PCTEST V1.0 12/17/2018 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact [email protected]. Plot 7-100. PAR Plot (Band 48 – 15.0MHz QPSK – Full RB Configuration) Plot 7-101. PAR Plot (Band 48 – 15.0MHz 16-QAM – Full RB Configuration) FCC ID: XIA-CFW2132 MEASUREMENT REPORT (CERTIFICATION) Approved by: Quality Manager Test Report S/N: Test Dates: EUT Type: Page 69 of 97 1M2003310053-01-R1.XIA 3/31 - 5/15/2020 Outdoor LTE Router © 2020 PCTEST V1.0 12/17/2018 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including …

Text truncated - open the document above for the full version.