XVE-TRX1032Winch with Winch mount&Wireless Remote

TRAXXAS.com Traxxas, 6250 Traxxas Way, McKinney, TX 75070, Phone: 972-549-3000, Fax: 972-549-3011, e-mail: [email protected] TRAXXAS.com Traxxas, 6250 Traxxas Way, McKinney, TX 75070, Téléphone: 972-549-3000, Fax: 972-549-3011, Adresse de courriel: [email protected] FCC Compliance This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. WARNING: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Disconnect the power source prior to defeating or bypassing the equipment safeguard; restore the equipment safeguard before restoring power. Canada, Innovation, Science and Economic Development (ISED) CAN ICES-3 (B) This device contains license-exempt transmitters that comply with Innovation, Science and Economic Development Canada’s license-exempt RSS(s). Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) This device must accept any interference, including interference that may cause undesired operation of the device. Radio Frequency (RF) Exposure Statement This equipment complies with FCC/IC RSS-102 radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. CE Compliance for Users in the European Union WEEE Compliance: Please help the environment by disposing of your product responsibly at the end of its life. The wheeled bin symbol indicates that this product should not be disposed of in your household waste containers. Instead, the product should be disposed of by using a designated collection point for the recycling of waste electrical and electronic equipment. The Waste of Electrical and Electronic Equipment (WEEE) Directive (2002/96/ EC) requires that the best available recycling techniques be employed to minimize the impact on the environment. Recycling electronics helps by keeping harmful chemicals out the environment, and also saves money by reusing precious metals. For more information about where you can drop off your waste equipment for recycling, please contact your local city office, your household waste disposal service or the location where you purchased this product. Declaration of Conformity for RED Directive Traxxas LP hereby declares that this product is in compliance with Directive 2014/53/ EU. The full text of the EU Declaration of Conformity is available online at: https://traxxas.com/compliance Signed: ___________________________ Date: ____________________ Traxxas, 6250 Traxxas Way, McKinney, TX 75070 USA Operation Frequency: 433.19 MHz Max. Output Power: -15.55 dBm or 0.028 mW for EU Compliance January 21, 2021 COMPLIANCE Conformité avec la FCC (Commission fédérale des communications) Ce dispositif est conforme à la 15e partie des règles de la FCC. Le fonctionnement en est assujetti aux deux conditions suivantes : (1) Ce dispositif ne doit pas causer d’interférences nuisibles et (2) Ce dispositif doit accepter toute interférence reçue, y compris les interférences qui peuvent mener à un fonctionnement non souhaité. Note : Cet équipement a été testé et déclaré conforme aux normes des dispositifs numériques de classe B, en vertu de la 15e partie des règles de la FCC. Ces normes sont conçues pour assurer une protection raisonnable contre les interférences nuisibles dans les locaux résidentiels. Ce produit émet, utilise et peut rayonner de l’énergie radioélectrique et, en cas d’installation ou d’utilisation contraire aux instructions, peut causer des interférences nuisibles aux radiocommunications. Cependant, rien ne garantit que des interférences ne se produiront pas dans une installation particulière. Si cet équipement provoque des interférences nuisibles avec la réception de la radio ou de la télévision, ce qui peut être vérifié en éteignant et en rallumant l’équipement, l’utilisateur est invité à essayer de corriger l’interférence par l’une ou plus des mesures suivantes : • Bougez ou déplacez l’antenne de réception. • Augmentez la distance séparant l’équipement du récepteur. • Branchez l’équipement à une prise d’un autre circuit que celui du récepteur. • Consultez le marchand d’agrément ou un technicien radio/TV expérimenté pour obtenir de l’aide. AVERTISSEMENT: Tout changement ou toute modification qui n’est pas expressément approuvé par la partie responsable de la conformité peut annuler l’autorisation de l’utilisateur à actionner l’équipement. Débranchez la source d’alimentation avant de retirer ou de contourner la protection de l’équipement; remettez en place la protection de l’équipement avant de rétablir l’alimentation. Canada, …

Text truncated - open the document above for the full version.

TRAXXAS.com Traxxas, 6250 Traxxas Way, McKinney, TX 75070, Phone: 972-549-3000, Fax: 972-549-3011, e-mail: [email protected] KC2831-R00 Rev 201112 Bumper Winch Installation Instructions Kit contents: • Winch with winch mount (Model: 8856) • Wireless remote (Model: 8857) • Fairlead (for optional mounting)** • Y-harness • 3x6mm pins (2) • 2.5x12mm cap screws (2)* • 2.5x10mm cap screws (2)** • Zip ties (3) Tools needed: • 1.5mm hex wrench • 2.0mm hex wrench Specifications: • Input voltage: 5-16.8 volts • Pulling capacity: 10 lbs Requirements for powering the winch: Covers Part #8855 Visitez Traxxas.com/manuals pour télécharger les instructions dans votre langue. Visite la página Traxxas.com/manuals para descargar el instrucciones en su idioma. Auf Traxxas.com/manuals, können Sie anleitung in Ihrer Sprache downloaden. Part No.Bumper StyleApplicable Models 8866 191mm 82010-4 TRX-4® Sport Unassembled Kit 82024-4 TRX-4® Sport 82034-4 TRX-4® Sport 8865 200mm 82016-4 Unassembled Kit 82056-4 Land Rover® Defender® 82066-4 Tactical Unit 8867 217mm 82046-4 Ford® Bronco® 82076-4 1979 Chevrolet® Blazer® 8869 227mm 9111X 1969 Chevrolet® Blazer® 9112X 1972 Chevrolet® Blazer® 886882096-4 Mercedes® G 500® 88096-4 Mercedes® G 63® Wireless Remote Channel Select Button Channel Indicator/ Activity LED Line Out Button Line In Button Fig. 1 Bumper Winch Status LED Bind ButtonFreespool Button Fig. 2 Press to release line The following vehicle-specific bumper parts packages are required for proper installation of the winch (each sold separately): Note: Refer to the special instructions that are included in the bumper package for installing this bumper set. WARNING: BURN HAZARD! This product contains a button cell battery. DO NOT ingest the battery. If the button cell battery is swallowed, it can cause severe internal burns in just 2 hours and can lead to death. If you think the battery might have been swallowed or placed inside any part of the body, seek immediate medical attention. • Risk of explosion if the battery is replaced by an incorrect type. Replace only with the same or equivalent type recommended by the manufacturer. • Disposal of the battery into fire or a hot oven, or mechanically crushing or cutting of the battery, can result in an explosion. • Extremely high temperatures and/or extremely low air pressure can result in an explosion or the leakage of flammable liquid or gas. • Keep new and used batteries away from children. • If the battery compartment does not close securely, stop using the product and keep it away from children. • Direct battery power • External BEC • BEC output from electronic speed control ESC) capable of 1-amp output TRAXXAS.com Traxxas, 6250 Traxxas Way, McKinney, TX 75070, Phone: 972-549-3000, Fax: 972-549-3011, e-mail: [email protected] Warranty Information Traxxas electronic components are warranted to be free from defects in materials and workmanship for a period of 30 days from the date of purchase. Limitations: Any and all warranty coverage does not cover replacement of parts and components damaged by abuse, neglect, improper or unreasonable use, crash damage, water or excessive moisture, chemical damage, improper or infrequent maintenance, accident, unauthorized alteration or modification or items that are considered consumable. Traxxas will not pay for the cost of shipping or transportation of a defective component to us. Traxxas Lifetime Electronics Warranty After the expiration date of the warranty period, Traxxas will repair electronic components for a flat rate. Please visit Traxxas.com/ support for a current schedule of warranty costs and fees. For patent and patent-pending information, please visit Traxxas.com/pat WARRANTY The covered repairs are limited to non-mechanical components that have NOT been subjected to abuse, misuse, or neglect. Products damaged by intentional abuse, misuse, or neglect may be subject to additional charges. Traxxas liability, in no case, shall be greater than the actual purchase price of this product. For replacement, product must be returned in brand new condition, with packaging and itemized sales receipt. Mercedes-Benz®, G 500®, and G 63® are trademarks of Mercedes-Benz/Daimler AG. Land Rover® and Defender® are trademarks of Jaguar Land Rover Limited. Ford® and Bronco® are trademarks of Ford Motor Company. Chevrolet® and Blazer® are trademarks of General Motors. All copyrights and trademarks are used by Traxxas under license. 8862 8862 8860 8860 8864R 8864 opt. 8864X opt. 8860 8860 8860 8860 8860 2.5x8mm CS 8858 8858 8863 8861 8859 8863 8863 2.5x12mm CS 1.6x7mm BCS (self-tapping) 2.5x12mm CS 2.5x10mm CS 2.5x10mm CS 2.5x20mm CS 2.6x8mm BCS 2.5x20mm CS PARTS LIST AND EXPLODED VIEW Part #Description 8858Housings (front & rear), winch/ decal 8859Fairlead, winch 8860Spool shaft assembly, winch 8861Spool, winch 8862Gearmotor, winch 8863Hook, winch (steel)/ line retainer/ washer 8864Line, winch (grey) 8864RLine, winch (red) 8864XLine, winch (blue) Installing the winch line retainer Install the included line retainer on the winch hook as shown below to help prevent the line from slipping off the hook. Route the wire from the winch to the XL-5 HV electronic speed control (on the XL-5 HV, the red connector is direct output voltage from the battery; the maximum voltage that the winch can accept is 4s LiPo) . Note: Be sure to allow adequate body clearance so that it doesn’t rub against or cut the wires. Secure any excess length of the wire with the existing left front wire clip and the included zip ties to prevent contact with any moving parts or assemblies. Plug the red male connector from the speed control into the red female connector from the winch. If you have another accessory installed, such as an external BEC or LED lighting, plug the red male connector from the speed control into the red female connector from the included Y-harness as shown. Plug the other red male connectors from the Y-harness into the red female connectors from the…

Text truncated - open the document above for the full version.

XVE-TRX1032

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Page: 1 of 4 External Photos for SZEM2005003733CR FCC ID: XVE-TRX1032 SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Page: 2 of 4 1 EUT Constructional Details SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Page: 3 of 4 SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Page: 4 of 4

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Page: 1 of 2 Internal Photos for SZEM2005003733CR FCC ID: XVE-TRX1032 SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Page: 2 of 2 1 EUT Constructional Details Antenna

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM200500373302 Page: 1 of 27 Keny Xu EMC Laboratory Manager TEST REPORT Application No.: SZEM2005003733CR Applicant: Traxxas LP Address of Applicant: 6250 Traxxas Way Mckinney, Texas, 75070, USA Manufacturer: Jason Toys & Electronics Co. Ltd. Address of Manufacturer: 6F, No. 133, Wu-Gong Road, Wu-Gu Township, Taipei County, Taiwan, 248 Equipment Under Test (EUT): EUT Name: Wireless Remote Model No.: 8857 Trade Mark: Traxxas FCC ID: XVE-TRX1032 Standard(s) : 47 CFR Part 15, Subpart C 15.231 Date of Receipt: 2020-05-13 Date of Test: 2020-05-14 to 2020-08-07 Date of Issue: 2021-03-30 Test Result: Pass* * In the configuration tested, the EUT complied with the standards specified above. SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM200500373302 Page: 2 of 27 Revision Record Version Chapter Date Modifier Remark 01 2021-03-30 Original Authorized for issue by: Harry Wu /Project Engineer Eric Fu /Reviewer SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM200500373302 Page: 3 of 27 2 Test Summary Radio Spectrum Technical Requirement Item Standard Method Requirement Result Antenna Requirement 47 CFR Part 15, Subpart C 15.231 N/A 47 CFR Part 15, Subpart C 15.203 Pass Radio Spectrum Matter Part Item Standard Method Requirement Result 20dB Bandwidth 47 CFR Part 15, Subpart C 15.231 ANSI C63.10 (2013) Section 6.9 47 CFR Part 15, Subpart C 15.231(c) Pass Dwell Time (15.231(a)) 47 CFR Part 15, Subpart C 15.231 ANSI C63.10 (2013) Section 7.5 47 CFR Part 15, Subpart C 15.231(a) Pass Field Strength of the Fundamental Signal (15.231(b)) 47 CFR Part 15, Subpart C 15.231 ANSI C63.10 (2013) Section 6.5 47 CFR Part 15, Subpart C 15.231(b) Pass Radiated Emissions 47 CFR Part 15, Subpart C 15.231 ANSI C63.10 (2013) Section 6.4&6.5&6.6 47 CFR Part 15, Subpart C 15.231(b) Pass SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM200500373302 Page: 4 of 27 3 Contents Page 1 COVER PAGE ............................................................................................................................................ 1 2 TEST SUMMARY ....................................................................................................................................... 3 3 CONTENTS ................................................................................................................................................ 4 4 GENERAL INFORMATION ........................................................................................................................ 5 4.1 DETAILS OF E.U.T. ............................................................................................................................... 5 4.2 DESCRIPTION OF SUPPORT UNITS ......................................................................................................... 5 4.3 MEASUREMENT UNCERTAINTY .............................................................................................................. 5 4.4 TEST LOCATION .................................................................................................................................... 6 4.5 TEST FACILITY ...................................................................................................................................... 6 4.6 DEVIATION FROM STANDARDS ............................................................................................................... 6 4.7 ABNORMALITIES FROM STANDARD CONDITIONS ..................................................................................... 6 5 EQUIPMENT LIST ...................................................................................................................................... 7 6 RADIO SPECTRUM TECHNICAL REQUIREMENT ............................................................................... 10 6.1 ANTENNA REQUIREMENT .................................................................................................................... 10 6.1.1 Test Requirement: ....................................................................................................................... 10 6.1.2 Conclusion ................................................................................................................................... 10 7 RADIO SPECTRUM MATTER TEST RESULTS ..................................................................................... 11 7.1 20DB BANDWIDTH .............................................................................................................................. 11 7.1.1 E.U.T. Operation .......................................................................................................................... 11 7.1.2 Test Setup Diagram ..................................................................................................................... 11 7.1.3 Measurement Procedure and Data............................................................................................. 11 7.2 DWELL TIME (15.231(A)) .................................................................................................................... 13 7.2.1 E.U.T. Operation .......................................................................................................................... 13 7.2.2 Test Setup Diagram ..................................................................................................................... 13 7.2.3 Measurement Procedure and Data............................................................................................. 13 7.3 FIELD STRENGTH OF THE FUNDAMENTAL SIGNAL (15.231(B)) ............................................................... 15 7.3.1 E.U.T. Operation .......................................................................................................................... 15 7.3.2 Test Setup Diagram .................................…

Text truncated - open the document above for the full version.

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Page: 1 of 3 Setup Photos for SZEM2005003733CR FCC ID: XVE-TRX1032 SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Page: 2 of 3 1 Photographs 1.1 Field Strength of the Fundamental Signal (15.231(b)) Test Setup SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Page: 3 of 3 1.2 Radiated Emissions Test Setup