Y3HCB660820120206wireless high-definition transmitter

USER MANUAL This user manual applies to:Transmitter : CV6608/ CB8801/ CB8808/ CB2601 Receiver : CV6620/ CB3801 Waste electrical products should notbe disposed of with household waste. Please recycle where facilities exist. Check with you local authority or retailer for recycling advice. EU Environmental Protection WIRELESS HD TRANSMISSION SYSTEM Please read this user manual before you use this product , it contains all the notes and impor- tant things regarding operating this product . In accordance with the safet precautions and operating instructions listed on this user manual , our applies provided the product is handled properly for its intended use , but may not apply to below cases : ● Repairs or product modification and alterations have been executed by unauthorized personnel . ● T h e damages are caused by accidents including but not limited to lightning , fire , exposed to rain or water,and moisture . ● Do not use provided power adapter with specific power voltage which are not compliant with the rated voltage range in the attached label of the power adapter in package . ● T h e model label on the product has been modified or the warranty tag has been removed by unauthorized personnel. The high temperature in the process of operating the device may cause the high risk of scalding . To reduce the risks of electricity , do not remove or open the cover . No user - serviceable parts are inside . Please return to original factory for maintenance Safety Precaution ● As connecting any equipment ( such as any player or TV , etc .), please turn off the power to the product before any operation is undertaken . ● Power outlet: To prevent electric shock or fire , short circuit , please make sure the type of electrical plug used on the receiv er's and transmitter's power cord are compliant with the rated voltage range in the attached label of the power adapter in package . ● Power cord : Do not place any heavy articles above on the power cord . To avoid being st epped on or pinched by heavy items , the power cord should not be located on the place where people pass by frequently . ● Power overloading : Avoid overloading wall's electrical outlets and extension cord or other multi - socket; otherwise could result in electronic shock or fire . ● Lightning : For protection from lightning or when the product is left unattended for a long period , please disconnect it from the power source. ● Please disconnect the power cord from the power outlet when you are not using the receiver and transmitter , this will reduce the risk of electric shock or fire . Danger : Be careful with electricity . ● T h i s product should not be exposed to dripping or splashing . Do not place any object filled with liquid on the product ( eg . vases ). ● To avoid electric shock , please do not block or stick anything on the air vent of product; do not remove the cover or put the object just like pins , steel wire into the gap of the air vent . ● Please place the receiver / emitter on a flat with hard and stable surface. ● Ventilation : please do not block the air vents on the receiver / transmitter or place any heavy object on top of them . Blocking the air flow can damage the product itself . Please make sure that there is adequate ventilation distance between the receiver and TV , and also put the product away from direct sunlight or any source of heat . ● Wa t e r Exposure : To reduce the risk of electric shock or fire , please do not expose the receiver / transmitter to rain or moisture. ● We're no responsible for any damage or result caused by unsing other adapters instead of our s tandard adapters Important Information Warning ● Although the product has provided the function of data encryption when transmitting , you still need to pay attention to deliberate signal interception . There will be the Possibility of a third party intentionally intercept the transmission signal since the product adopt wireless communication. Please do not use the product on confidential and important c ommunications, or life-related communications The main concern is that the content of wireless c ommunication might be received by the third party's wireless de vices deliberately or accidentally . ● T h e impact of radio waves ( such as the following environment may cause the abnormal audio and video ( blocked image , noise ... etc .). 1 ) Transmit near the wall which is hard for the radio waves to get through. 2 ) Quite close to the refrigerator , metal fitment and appliances , or next to the crowded situation. ● This product has been tested and manufactured to comply with national electrical safety rules , however , there will be noise caused by the interference with other machines in rare cases . If the interference is happened , please keep a certain distance away from other machines . ● T h e product is susceptible to interference from 5GHz wireless local area network or other wir eless devices. ● Optimal range between transmitter and receiver is between 1 meter and 30 meters within line of sight indoor . ● Please do not set up the transmitter and receiver in metal shelf , or it will hinder the wireless communications . ● 1080P / 60 Hz Wireless transmitting . ● It will take 15 - 20 seconds to boot the system before wireless communication start , the media receiver can not be operated during this time . ● This wireless product has minute amounts of radiation, pls kee p at least 20cm away from human while using Special Notice Danger! High voltage Beware of hot surfaces! Caution! Please use our standard power adapter.Detailed information refer to the rated voltage range showed on the label at the back of package's power adapter. Please ● This product is for indoor use only. 01 02 CONTENTS About the instructions 02 Brief introduction 02 Packing List 03 Interface Introduction 05 Wireless HD Transmitter introduction(CV6608, CV8801, CB8808, CB 2601) 05 Wireless HD Receiver introduction(CV6620, CV3801) 07 Installation and Use 09 Connect to …

Text truncated - open the document above for the full version.

EXHIBIT B - EUT EXTERNAL PHOTOGRAPHS EUT—All View EUT – Top View EUT – Bottom View EUT – Side View 1 EUT – Side View 2 EUT – Adapter View EUT – Adapter Label View

EXHIBIT A - FCC ID LABELING AND LOCATION FCC ID Label FCC ID Label Location The label shown shall be permanently affixed at a conspicuous location on the device and be readily visible to the user at the time purchase (Labeling requirements per 2.925)

EXHIBIT C - EUT INTERNAL PHOTOGRAPHS EUT – Uncover View EUT – Cover Off View EUT – Main Board TopView EUT –Main Board Top Without Copper Foil View EUT – Antenna View EUT – Main Board Bottom View TX RX

Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: R1DG120210006-00 FCC Part 15.407 Page 8 of 50 FCC §15.407 (f), §2.1093, §1.1307(b) (1) – RF EXPOSURE EVALUATION Applicable Standard According to subpart 15.247(i)and subpart §1.1307(b)(1), systems operating under the provisions of this section shall be operated in a manner that ensures that the public is not exposed to radio frequency energy level in excess of the Commission’s guidelines. Limits for Maximum Permissible Exposure (MPE) (§1.1310, §2.1091) (B) Limits for General Population/Uncontrolled Exposure Frequency Range (MHz) Electric Field Strength (V/m) Magnetic Field Strength (A/m) Power Density (mW/cm 2 ) Averaging Time (minutes) 0.3–1.34 614 1.63 *(100) 30 1.34–30 824/f 2.19/f *(180/f²) 30 30–300 27.5 0.073 0.2 30 300–1500 / / f/1500 30 1500–100,000 / / 1.0 30 f = frequency in MHz; * = Plane-wave equivalent power density; According to §1.1310 and §2.1091 RF exposure is calculated. Calculated Formulary: Predication of MPE limit at a given distance S = PG/4πR² = power density (in appropriate units, e.g. mW/cm 2 ); P = power input to the antenna (in appropriate units, e.g., mW); G = power gain of the antenna in the direction of interest relative to an isotropic radiator, the power gain factor, is normally numeric gain; R = distance to the center of radiation of the antenna (appropriate units, e.g., cm); Calculated Data: Antenna Gain Conducted Power Frequency (MHz) (dBi) (numeric) (dBm)(mW) Evaluation Distance (cm) Power Density (mW/cm 2 ) MPE Limit (mW/cm 2 ) 5230 2.9 1.949 12.4517.57920 0.0068 1.0 Result: The device meet FCC MPE at 20 cm distance

Note: This test report is prepared for the customer shown above and for the device described herein. It may not be duplicated or used in part without prior written consent from Bay Area Compliance Laboratories Corp. This report must not be used by the customer to claim product certification, approval, or endorsement by NVLAP*, or any agency of the Federal Government. * This report contains data that are not covered by the NVLAP accreditation and are marked with an asterisk “★” (Rev.2) FCC PART 15.407 TEST REPORT For Shenzhen Crystal Video Technology Co., Ltd. F13，F518 Idea Land, Baoyuan Road, Baoan Central Area, Shenzhen, China Report Type: Original Report Product Type: wireless high-definition transmitter Test Engineer: Ares Liu Report Number: R1DG120210006-00 Report Date: 2012-03-08 Reviewed By: Merry Zhao EMC Engineer Test Laboratory: Bay Area Compliance Laboratories Corp. (Shenzhen) 6/F, the 3rd Phase of WanLi Industrial Building, ShiHua Road, FuTian Free Trade Zone Shenzhen, Guangdong, China Tel: +86-755-33320018 Fax: +86-755-33320008 www.baclcorp.com.cn FCC ID: Y3HCB660820120206 Bay Area Compliance Laboratories Corp. (Shenzhen) Report No.: R1DG120210006-00 FCC Part 15.407 Page 2 of 50 TABLE OF CONTENTS GENERAL INFORMATION.......................................................................................................................................4 PRODUCT DESCRIPTION FOR EQUIPMENT UNDER TEST (EUT) .....................................................................................4 OBJECTIVE...................................................................................................................................................................4 RELATED SUBMITTAL(S)/GRANT(S).............................................................................................................................4 TEST METHODOLOGY..................................................................................................................................................4 TEST FACILITY.............................................................................................................................................................5 SYSTEM TEST CONFIGURATION ..........................................................................................................................6 DESCRIPTION OF TEST CONFIGURATION......................................................................................................................6 EUT EXERCISE SOFTWARE..........................................................................................................................................6 EQUIPMENT MODIFICATIONS.......................................................................................................................................6 BLOCK DIAGRAM OF TEST SETUP................................................................................................................................6 SUMMARY OF TEST RESULTS...............................................................................................................................7 FCC §15.407 (f), §2.1093, §1.1307(b) (1) – RF EXPOSURE EVALUATION.............................................................8 APPLICABLE STANDARD..............................................................................................................................................8 FCC §15.203 – ANTENNA REQUIREMENT ............................................................................................................9 APPLICABLE STANDARD..............................................................................................................................................9 ANTENNA CONNECTOR CONSTRUCTION......................................................................................................................9 FCC §15.407 (b) (6) §15.207 (a) – CONDUCTED EMISSIONS .............................................................................10 APPLICABLE STANDARD............................................................................................................................................10 MEASUREMENT UNCERTAINTY..................................................................................................................................10 EUT SETUP................................................................................................................................................................10 EMI TEST RECEIVER SETUP.......................................................................................................................................11 TEST EQUIPMENT LIST AND DETAILS.........................................................................................................................11 TEST PROCEDURE......................................................................................................................................................11 TEST RESULTS SUMMARY..........................................................................................................................................11 TEST DATA................................................................................................................................................................11 FCC §15.209, §15.205 & §15.407(b) (1) (6) (7) – UNDESIRABLE EMISSION & RESTRICTED BANDS .......14 APPLICABLE STANDARD............................................................................................................................................14 MEASUREMENT UNCERTAINTY..................................................................................................................................14 EUT SETUP................................................................................................................................................................14 EMI TEST RECEIVER & SPECTRUM ANALYZER SETUP............................................................…

Text truncated - open the document above for the full version.

EXHIBIT C - TEST SETUP PHOTOGRAPHS Conducted Emissions- Front View Conducted Emissions- Side View Radiated Emissions - Front View Radiated Emissions - Rear View