Y6D-MWSAR010MWS Reader

MWS Reader User Manual Index 1. Technical specifications..............................................................................................2 2. Reader power supply..................................................................................................2 3. Bluetooth connection to PC........................................................................................3 4. Other information and support...................................................................................4 MWS Reader – User manual July 2014 1 MWS Reader User Manual Reader capable of reading 2.4 GHz active Tags equipped with Bluetooth interface, embedded antenna, 12 V or 24 V power supply. The MWS Reader uses 2,4GHz standard (IEEE 802.15.4) to communicate with active tags with sensor on board and allows the user to monitor temperature, electronic sealing, humidity, etc. 1. Technical specifications INTERNAL DEVICES Frequency: 2.4 GHz Power: Programmable up to 4.5 dBm Standard: IEEE 802.15.4 Reading distance: 100 m INTERFACES Bluetooth Class 2 V2.1+ EDR POWER SUPPLY 12 - 24 V (Car adapter, wall adapter or battery) stand by consumption 1 mA WORKING TEMPERATURE -20 / +70°C DIMENSIONS Width 65 mm – Height 50 mm – Depth 37 mm WEIGHT 70 g PROTECTION DEGREE IP65 2. Reader power supply The reader supply voltage range is from 12V to 48V. The supply cable diameter must be from 3.5mm to 5.5mm. Strip the external cable jacket for 6 mm and the ones of the internal wires for 6 mm. Connected the wires and fasten them with a cable tie close to the cable gland as shown in Fig.1. The cable tie makes the installation more tear-resistent. MWS Reader – User manual July 2014 2 Fig. 1: power supply cable connection It can be powered via a standard wall adapter power supply or battery. When installed in vehicle, the reader power supply should usually be taken directly from the battery of the vehicle and not from the ignition. Note: when Bluetooth is not active reader power consumption is very low, about 1mA. MWS Reader can read MWS Tags up to a distance of 100m. See chapter 3. Bluetooth connection to PC and Configuration and test using IceTag_PCDemoto get data from MWS Tags. 3. Bluetooth connection to PC MWS Reader can be quickly connect to your PC via Bluetooth to start to configure it and test it using IceTag_PCDemo. Once it is switched on, MWS Reader is shown up under BluetoothDevice Directory as Serial Port Profile (SPP) with the name MWSAR_BT12V_XXXX. The first time you need to pair it by double clicking on the MWSReader name and inserting the PIN code 1234. After the pairing process, the remote host assigns a virtual COM port to the device. To configure and test the device, run IceTag_PCDemo and connect to the virtual COM port (see document Configuration and test using IceTag_PCDemo). All the commands are simple serial packets and allow to change setting of the devices and get data from the active tag. For further details about MWS Reader protocol, see TERTIUM_IceTag_Reader_Protocol.pdf. MWS Reader – User manual July 2014 3 4. Other information and support Declaration of conformity ManufacturerTERTIUM Technology S.r.l. Via Picotti,8 56124 Pisa Italy ProductMWS Reader Description2.4GHz RFID fixed reader with Bluetooth interface Conformity standard ETSI version EMC: EN 301.489-1 V1.9.2, EN 301.489-3 V1.6.1, EN 301.489-17 V2.2.1 [Art. 3.1b – 99/05/CEE] Safety: EN 60950-1:2006 +/A11:2009 +/A12:2011 +/A1:2010 [Art. 3.1a – 99/05/CEE] EMF: EN 50364:2010 [Art. 3.1a – 99/05/CEE] ERM: ETSI EN 300 328 V1.8.1 [Art. 3.2 – 99/05/CEE] The present document declares that MWS Reader product is compliant with the standards described above and they meet the essential requirements expressed in the European Directive 99/05/CE and FCC rules. Based on these declarations, the product can bear the following mark: Federal Communication Commission (FCC) Notice FCC certified: FCC ID: Y6D-MWSAR010 THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFER- ENCE THAT MAY CAUSE UNDESIRED OPERATION. NOTE: THE GRANTEE IS NOT RESPONSIBLE FOR ANY CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED BY THE PARTY RESPONSIBLE FOR COMPLIANCE COULD VOID THE USER’S AUTHORITY TO OPERATE THE EQUIPMENT. MWS Reader – User manual July 2014 4 Dr. Marco Consani This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: —Reorient or relocate the receiving antenna. —Increase the separation between the equipment and receiver. —Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. —Consult the dealer or an experienced radio/TV technician for help. Disposal According to art.13 of the Legislative Decree dated 25 July 2005, no.151 (implementation of the European directive 2002/96/EC) the disposal of electric and electronic equipment (WEEE) must not be carried out as urban waste, but it must be done separately following specific guidelines. Such obligation is expressed by the following symbol, applied on the container. The disposal will be managed by the producer and therefore the consumer wishing to get rid of the device shall con…

Text truncated - open the document above for the full version.

Federal Communication Commission 7435 Oakland Mills Road Columbia, MD 21046 30 th , September 2014 Gentlemen: This letter is to comply with Sections 0.457 and 0.459 pertaining to confidential material. TERTIUM Technology S.r.l. would like the following documents regarding this submission for FCC ID: Y6D-MWSAR010 to be kept confidential. Documnents: 1.Block Diagram 2.Operational Descritpion 3.Schematic Diagrams 4.Part List The above material contains trade secrets or thecnical data, which would customarily be guarded from competitors. We do not want these documents to be accessible to the general public. Sincerely Marco Consani General Manager TERTIUM Technology S.r.l. via G.B. Picotti, 8 – 56124 PISA (Italy) – Tel. e Fax +39 050 57 67 77 partita I.V.A. e C.F. 01594480509

Mode of transmission of different RF modules of MWS Reader 11 th November 2014 Subject: non-simultaneous transmission of Bluetooth module and IEEE 802.15.4 module of MWS Reader FCC ID: Y6D-MWSAR010 We TERTIUM Technology S.r.l., declare that the normal operating mode of MWS Reader does not allow the bluetooth module and the IEEE 802.15.4 module to transmit data at the same time. The MWS Reader always wait for the IEEE 802.15.4 transmission to end before starting a Bluetooth transmission. Company Name: TERTIUM Technology S.r.l. Company Address: Via G.B. Picotti, 8 – 56124 PISA – ITALY 1

MADE IN ITALY FCC ID: Y6D-MWSAR010 MWS Reader tertiumtechnolog y.com MWSAR-FA1312-48VDC 500m A Contains FCC ID T9J-RN42

G.S.D. S.r.l. Via Marmiceto, 8 - 56121 Ospedaletto (Pisa) Italy MARKING ELECTROMAGNETIC COMPATIBILITY ELECTRICAL SAFETY LASER SPECTROSCOPY ENVIRONMENTAL PHYSIC G.S.D. S.r.l PISA - Italy Test Report n. 14450 Rev. 01 Manufacturer TERTIUM Technology S.r.l. AddressVia G. B. Picotti, 8 56124 Pisa Italy Test Family Name MWS Reader Frequency Range / RF 2405-2480 MHz Testing Laboratory Name G.S.D. S.r.l. AddressVia Marmiceto, 8 56121 Ospedaletto Pisa (PI) Italy Tel/Fax+39 050 984254 / +39 050 984262 P.IVA/VAT01343950505 http – e-mailwww.gsd.it - [email protected] FCC Listed: Registration Number: 424037 IC Listed: Registration Number: 9353A Location and Date of IssuePisa, 2014 November 11 This document may be only fully reproduced. Every partial reproduction is only allowed after written approval released by G.S.D. S.r.l. Report n. 14450 Rev. 01, page 1 / 35 Laboratories G.S.D. S.r.l. Via Marmiceto, 8 - 56121 Ospedaletto (Pisa) Italy INDEX 1.MANUFACTURER AND EUT IDENTIFICATION ...................................................................................3 2.REFERENCE STANDARDS...............................................................................................................5 3.RESULT, CONDITION, MEASUREMENT UNCERTAINTY......................................................................6 4.6 DB BANDWIDTH.........................................................................................................................7 5.MAXIMUM PEAK OUTPUT POWER...............................................................................................11 6.BAND EDGE AND CONDUCTED SPURIOUS EMISSIONS...................................................................15 7.PEAK POWER SPECTRAL DENSITY...............................................................................................18 8.RADIATED EMISSIONS..................................................................................................................23 9.MAXIMUM PERMISSIBLE EXPOSURE.............................................................................................33 10.PHOTO........................................................................................................................................34 This document may be only fully reproduced. Every partial reproduction is only allowed after written approval released by G.S.D. S.r.l. Report n. 14450 Rev. 01, page 2 / 35 G.S.D. S.r.l. Via Marmiceto, 8 - 56121 Ospedaletto (Pisa) Italy 1.MANUFACTURER AND EUT IDENTIFICATION 1 Manufacturer TERTIUM Technology S.r.l.. AddressVia G. B. Picotti, 8 56124 Pisa Italy Test Family Name MWS Reader Date of reception2014 August 07 SamplingLaboratory sample for certification Test Item DescriptionWiFi Device Nominal Input Voltage12 Vdc Software FCC IDY6D-MWSAR010 1 A detailed documentation is preserved in the internal fascicle. This document may be only fully reproduced. Every partial reproduction is only allowed after written approval released by G.S.D. S.r.l. Report n. 14450 Rev. 01, page 3 / 35 G.S.D. S.r.l. Via Marmiceto, 8 - 56121 Ospedaletto (Pisa) Italy Fig. 1.1 Equipment Under Test - Photo This document may be only fully reproduced. Every partial reproduction is only allowed after written approval released by G.S.D. S.r.l. Report n. 14450 Rev. 01, page 4 / 35 G.S.D. S.r.l. Via Marmiceto, 8 - 56121 Ospedaletto (Pisa) Italy 2.REFERENCE STANDARDS Tests and measurements are performed accordingly to the reference standards given in the table below: TESTSTANDARD Operation within the band 2400-2483,5 MHz: Test Procedures 15.247 (a)(2), (b)(3), (d), (e) FCC Rules ad Regulations, Title 47 Part 15 – Sub part B ANSI C63.4 (2009) – American National Standard for Methods of Measuring of Radio-Noise Emissions from Low Voltage Electrical and Electronic Equipment in the Range of 9 kHz – 40 GHz FCC KDB 558074 D01 DTS Meas Guidance v03r02 Maximum Permissible ExposureOET Bulletin 65 Evaluating Compliance with FCC Guidelines for Human Exposure to Radiofrequency Electromagnetic Fields FCC Rules ad Regulations, Title 47 (2008) Part 15 – Sub part B This document may be only fully reproduced. Every partial reproduction is only allowed after written approval released by G.S.D. S.r.l. Report n. 14450 Rev. 01, page 5 / 35 G.S.D. S.r.l. Via Marmiceto, 8 - 56121 Ospedaletto (Pisa) Italy 3.RESULT, CONDITION, MEASUREMENT UNCERTAINTY Summary of Test Results TESTRESULT 6 dB bandwidht Section 15.247 (a) (2) KDB 558074 §8 Option 1 Pass Peak Conducted Output Power: Section 15.247 (b) (3) KDB 558074 §9.1.1 Pass Band Edge Section 15.247 (d) KDB 558074 §13.3.1 Pass Power Spectral Density Section 15.247 (e) KDB 558074 §10.1 Pass Radiated Emissions Section 15.209 KDB 558074 §12 Pass Internal Procedures: APR01: internal procedure for antenna port measurement Revision 01 CE22R01: internal procedure for power lead port measurement Revision 01 RE22R02: internal procedure for radiated emissions measurement Revision 02 Measurement uncertainty TESTEXPANDED UNCERTAINTY Conducted Emission – 50W/50mH AMN (150 kHz - 30 MHz) ± 3.5 dB Radiated Emission – (Semianechoic Room) (30 MHz - 40 GHz)± 4.7 dB Climatic Conditions PARAMETERVALUE Temperature (293  3) K Relative humidity (50  5) % Power during the tests: Internal battery Extensions The results refer only to the sampled EUT and under the specified conditions. This document may be only fully reproduced. Every partial reproduction is only allowed after written approval released by G.S.D. S.r.l. Report n. 14450 Rev. 01, page 6 / 35 G.S.D. S.r.l. Via Marmiceto, 8 - 56121 Ospedaletto (Pisa) Italy 4.6 dB BANDWIDTH Peak Output Power Equipment shall meet the limits below . FREQUENCY RANGE (MHz) Limit 2400 2483,5The minimum 6 dB Bandwidth shall be at least 500 kHz Results: 6dB Bandwidth > 500 kHz ChannelFrequency (MHz) 6 dB Bandwidth (MHz) Minimum Limit (MHz) Margin (MHz) Low24051,5150,51,02 Mid24401,6560,51,16 High24801,6540,51,15 Test Equipment EQUIPMENTMANUFACTURERMODELCAL. DATE EMI ReceiverAgilentE4440A01/2015 Test…

Text truncated - open the document above for the full version.