YCK-CM100GLTE-MBlackvue Connectivity Module

CM100GLTE-M ENGLISH / 日本語/ 中文 CM100GLTE-M Check the SIM card that is included in the package and remove the nano SIM fromthe SIM card pack. tools. Insert the SIM card into the slot. To avoid dysfunction of GPS, You must attach the connectivity module to the windshield area since GPS will work properly when the attachment part of the device is facing towards the windshield. CM100GLTE-M Check connectivity status if connection is not stable. Cloud Lite service. 2. To activate your SIM card, Please input the below APN information in the blank of the SIM card activation page. APN : internet.lte.cxn 3. You only need to input APN as described above, you neither need to input user name nor password. CM100GLTE-M CM100GLTE-M CM100GLTE-M 003-180062 FCC ID : YCK-CM100GLTE-M / FCC Contains ID : XMR201707BG96 IC ID : 23402-CM100GLTE-M / ISED Contains ID : 10224A-201709BG96 CM100GLTE-M blackvueofficial FCC Compliance Information This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protections against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on, the user is encouraged to ty to correct the interference by one or more of the following measures. y Reorient or relocate the receiving antenna. y Increase the separation between the equipment and receiver. y Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. y Consult the dealer or an experienced radio, TV technician for help. y Only shielded interface cable should be used. Finally, any changes or modifications to the equipment by the user not expressly appr oved by the grantee or manufacture could void the user’s authority to operate such equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation of this device. FCC RF Radiation Exposure Statement: This equipment complies with FCC RF Radiation exposure limits set forth for an uncontrolled environment. This device and its antenna must not be co-located or operating in conjunction with any other antenna or transmitter. This equipment should be installed and operated with a minimum distance of 20 cm between the radiator and your body.

Applicant Declaration Applicant Declaration Rev:0.0 SGS North America Inc. 620 Old Peachtree Road SUITE 100 Suwanee, Georgia 30024 United States Applicant Legal Business Name Pittasoft Co., Ltd. Address A 4th floor, ABN Tower, 331, Pangyo-ro, Bundang-gu, Seongnam-si, Gyeonggi-do, 13488, South Korea Grantee Code YCK FCC ID YCK-CM100GLTE-M Authorized Contact Name Kwang-Jo Kim Contact Email [email protected] Contact Phone 82-10-8998-8734 I, the undersigned, certify that I am an authorized signatory for the Applicant and therefore declare; a) in accordance with 47CFR2.911(d), all of the statements herein and the exhibits attached hereto are true and correct to the best of my knowledge and belief. b) in accepting a Grant of Equipment Authorization issued by a TCB, under the authority of the FCC, as a result of the representations made in this application, the Applicant is responsible for: (1) labeling the equipment with the exact FCC ID as specified in this application, (2) compliance statement labeling pursuant to the applicable rules, (3) compliance of the equipment with the applicable technical rules, c) if the Applicant is not the actual manufacturer of the equipment, appropriate arrangements have been made with the manufacturer to ensure that production units of this equipment will continue to comply with the FCC’s technical requirements. d) in accordance with 47 CFR 2.909 and KDB394321, the Applicant has read, understood and agrees to accept that they are the responsible party and agree to abide by their responsibilities as specified under 47 CFR 2.909 and KDB394321. e) in accordance with ISO17065, FCC KDB641163, FCC KDB610077, KDB394321 and RSP-100, the Applicant has read, understood, accepts and agrees to abide by the post market surveillance requirements. (1) the Applicant understands, accepts and agrees that a sample may be requested for surveillance testing. (2) the Applicant shall make provisions to always have a production sample available upon request by SGS, FCC and/or ISED. (3) the Applicant shall, upon request by SGS, at the Applicant’s expense, provide a production sample of the requested product to SGS, FCC and/or ISED as instructed. The sample shall include all support devices, cables, software, accessories or other hardware or software required for evaluation, review, certification and audit surveillance of products certified by SGS. f) neither the Applicant nor any party to the application is subject to a denial of Federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. §862 because of a conviction for possession or distribution of a controlled substance. See 47CFR 1.2002(b) for the definition of a “party” for these purposes. g) the Applicant has read, understood, accepts and agrees to abide by the SGS North America, Inc.(TCB) terms and conditions. Link to CFRs: https://www.fcc.gov/wireless/bureau-divisions/technologies-systems-and-innovation-division/rules-regulations-title-47 Link to KDBs: https://apps.fcc.gov/oetcf/kdb/index.cfm Link to RSP-100: https://www.ic.gc.ca/eic/site/smt- gst.nsf/eng/sf01130.html Applicant Signature: Date: June 15, 2020 Print Name: Kwang-Jo Kim Title: Research Advisor *NOTE: This declaration cannot be signed by an Agent, it shall be signed by an authorized person listed in the FCC database

Date: June 11, 2020 TO: Federal Communication Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MID 21046 Regarding: YCK-CM100GLTE-M To whom it may concern: We, the undersigned, hereby authorize SGS Korea Co., Ltd. to act on our behalf in all manners relating to application for equipment authorization with respect to the FCC ID above, including signing of all documents relating to these matters. Any and all acts carried out by the agent on our behalf shall have the same effect as acts of our own. We, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). Where our agent signs the application for certification on our behalf, I acknowledge that all responsibility for complying with the terms and conditions for Certification, as specified by SGS North America, Inc., still resides with Pittasoft Co., Ltd. This authorization is valid until further written notice from the applicant. Name (Printed): Kim, Kwang Jo Title: Research Advisor Signature: On behalf of Company: Pittasoft Co., Ltd. Telephone: 82-10-8998-8734

Date: June 11, 2020 To: SGS North America Inc. 620 Old Peachtree Road SUITE 100 Suwanee, Georgia United States From: Pittasoft Co., Ltd. 7F, BYC HIGH CITY Building A 131, Gasan Digital-ro, Geumcheon-gu, Seoul, South Korea Regarding: Confidentiality Request regarding application for FCC ID : YCK-CM100GLTE-M LONG TERM CONFIDENTIALITY Pursuant to 47 CFR Section 0.459 and 0.457 of the commission’s rules, the applicant hereby request confidential treatment of the documents listed below, associated with the certification application referenced above. Schematic(s) Block Diagrams Operational Descriptions The documents above contain proprietary information not released to the public. Public disclosure of this information may prove harmful to the business of the applicant. SHORT TERM CONFIDENTIALITY Additionally, the applicant requests the following documents be held confidential until the device is marketed or 180 days from the grant date, whichever is less. If the device is marketed within 180 days of the Grant Date, the applicant will notify the TCB per FCC KDB 726920 D01 Confidentiality Request Procedures. External Photos Internal Photos Test Setup Photos User manual(s) Sincerely, Kim, Kwang Jo Research Advisor Pittasoft Co., Ltd.

Front View of EUT Rear View of EUT Inside of EUT Front View of Main Board Rear View of Main Board View of Antenna

CM100GLTE-M_Product_CM100GLTE-M(NA) 1.2020.05.26 Model: CM100GLTE-M [NA] Contains FCC ID : XMR201707BG96 Contains IC ID : 10224A-201709BG96 Built-in Cat.M1 LTE-M Built-in GPS+GLONASS

Front View of EUT Rear View of EUT Inside of EUT Front View of Main Board Rear View of Main Board View of Antenna

Test Report No. : F690501-RF-EMG000177 Page : 2 of 10 EMC5101-01A(2017.07.06)(2) A4(210mm*297mm) Contents 1. General Information ................................................................................................... 4 1.1 Client Information ................................................................................................ 4 1.2 Test Laboratory ................................................................................................... 4 1.3 General Information of E.U.T. ............................................................................. 4 1.4 Operating Modes and Conditions ........................................................................ 5 1.5 Auxiliary Equipments .......................................................................................... 5 1.6 Cable List ............................................................................................................ 5 1.7 System Configurations ........................................................................................ 5 1.8 Test System Layout ............................................................................................ 6 1.9 Modifications ....................................................................................................... 6 1.10 Applicable Standards for Testing ...................................................................... 6 1.11 Summary of Test Results .................................................................................. 6 2. Emission Test ............................................................................................................ 7 2.1 Test Results ........................................................................................................ 7 2.2 Test Method and Limits ....................................................................................... 7 2.2.1 Test Method ............................................................................................... 7 2.2.2 Test Limits .................................................................................................. 7 2.3 Radiated Emission .............................................................................................. 8 2.3.1 Test Equipments ........................................................................................ 8 2.3.2 Test Site ..................................................................................................... 8 2.3.3 Environment Conditions and data .............................................................. 8 Appendix A : Radiated Emission ................................................................................. 10 Test Report No. : F690501-RF-EMG000177 Page : 3 of 10 EMC5101-01A(2017.07.06)(2) A4(210mm*297mm) Revision History Revision Report Number Description 0 F690501-RF-EMG000177 Initial 1 2 Test Report No. : F690501-RF-EMG000177 Page : 4 of 10 EMC5101-01A(2017.07.06)(2) A4(210mm*297mm) 1. General Information 1.1 Client Information Applicant : Pittasoft Co., Ltd. - Address of Applicant : A 4th floor, ABN Tower, 331, Pangyo-ro, Bundang-gu, Seongnam-si, Gyeonggi-do, Republic of Korea Manufacturer : Pittasoft Co., Ltd. - Address of Manufacturer : A 4th floor, ABN Tower, 331, Pangyo-ro, Bundang-gu, Seongnam-si, Gyeonggi-do, Republic of Korea Factory : SMT SCOUT Co., Ltd. - Address of Factory : 38 Dangjeong-ro, Gunpo-si, Gyeonggi-do, Republic of Korea, 15849 1.2 Test Laboratory Name and Address : SGS Korea Co., Ltd. - Giheung 1 Laboratory : 35, Giheungdanji-ro 121beon-gil, Giheung-gu, Yongin-si, Gyeonggi-do, Republic of Korea - Giheung 2 Laboratory : 23, Giheungdanji-ro 24beon-gil, Giheung-gu,Yongin-si, Gyeonggi-do, Republic of Korea - Gunpo Laboratory : 4, LS-ro 182beon-gil, Gunpo-si, Gyeonggi-do, 15807, Republic of Korea. Phone : + 82 31 428 5700 Fax : + 82 31 427 2370 e-mail : [email protected] 1.3 General Information of E.U.T. Classification Description Product Name Blackvue Connectivity Module Model Name CM100GLTE-M Serial No. CM1MNAAJ300001 Highest Internal Frequency 1 850 ㎒ ~ 1 990 ㎒ EMI Classification Class B Test Voltage 120 V~, 60 ㎐(for Travel Adapter), 12 Vd.c.(for Battery) Operating Voltage 5.0 Vd.c. 2.0 A (Minimum 2.7 Vd.c. ~ Maximum 5.5 Vd.c.) Operating Temperature (-)35 °C ~ (+)75 °C S/W Version CM100GLTE-M_VER_0.90 H/W Version CM100GLTE-M_ES_V02 Function This device is an LTE-M connection used in Dash Cam. Test Report No. : F690501-RF-EMG000177 Page : 5 of 10 EMC5101-01A(2017.07.06)(2) A4(210mm*297mm) 1.4 Operating Modes and Conditions Operating Mode Percussor 1) LTE Category M1 B2 Idle Standby ((LTE Category M1 B2) Mode 1.5 Auxiliary Equipments Description Model Serial No. Manufacturer Travel Adapter EP-TA200 R37MA8S2NF1SE3 SAMSUNG Power Module KM001 - Chargerlab Car Battery - - - Dash Cam BLACKVUE Cloud - Pittasoft Co., Ltd. 1.6 Cable List Start END Cable Spec. Used core Name I/O Port Name I/O Port Length Shield Radiated Emission(Below 1 ㎓) Test Car Battery AC OUT Dash Cam AC IN 4.2 Unshield No Dash Cam DC OUT EUT DC IN 1.5 Unshield No Radiated Emission(Above 1 ㎓) Test AC Source AC OUT Travel Adapter AC IN - - - Travel Adapter DC OUT Power Module DC IN - - - Power Module USB EUT - 1.5 Unshield No 1.7 System Configurations Description Model Serial No. Manufacturer Main Board CM100LTE_PP_V02 - - Antenna - - - Note. Antenna Requirement For intentional device, according to FCC 47 CFR Section §15.203, an intentional radiator shall be designed to ensure that no antenna other than that furnished by the responsible party shall be used with the device. The antennas have unique connectors. - Antenna gain Category Antenna Gain(㏈i) GSM1900 3.0 LTE FDD 2 3.0 LTE FDD 4 1.25 LTE FDD 12 1.8 LTE FDD 39 3.0 Test Report No. : F690501-RF-EMG000177 Page : 6 of 10 EMC5101-01A(2017.07.06)(2) A4(210mm*297mm) 1.8 Test System Layout - Radiated Emission(Below 1 ㎓) Test - Radiated Emission(Above 1 ㎓) Test 1.9 Modifications - There was no modified item during t…

Text truncated - open the document above for the full version.

Radiated Emission (Below 1 ㎓ ) _ Front Radiated Emission (Below 1 ㎓ ) _ Rear Radiated Emission ( Above 1 ㎓ ) _ Front Radiated Emission ( Above 1 ㎓ ) _ Rear