YETCELFI-RS224CUAT-Mobile Provider Specific Consumer Signal Booster

USER MANUAL Cel-Fi ® with IntelliBoost ™ STOP!!! Do not call your carrier until you have read the Quick Start Guide. If you need more help, try visiting http://www.celfihelp.com Safety Precautions • Install Cel-Fi indoors. It should not be used outdoors. • These products are designed to be used with a direct plug-in power supply unit meeting SELV and “Limited Power Source” (NEC/CEC Class 2) requirements rated 12 Vdc, 1.66 A. When installing the equipment, all the requirements of the manufacturer and the referenced standards must be met. • There are no user serviceable parts inside. CAUTION: Changes or modifications to this product not expressly approved by Nextivity may void your right to operate the equipment. Declaration of Conformity We, Nextivity, Incorporated, 12230 World Trade Drive Suite 250, San Diego, CA 92128, USA declare under our sole responsibility that the product(s): Product Description: Cel-Fi Residential (CELFI-RS2) Models: CELFI-RS218WU and CELFI-RS218CU to which this declaration relate(s) is(are) in conformance with the provisions of Directive 1999/5/EC governing Radio Equipment and Telecommunications Terminal Equipment and the Mutual Recognition of their Conformity using the following standards (CELFI-RS224 and CELFI-RS225 EMC/Radio are covered by FCC/IC requirements): SAFETY (art 3.1.a): EN 60950:2006 /A11:2009 /A1:2010 EMC: (art 3.1.b): EN 301 489-1 v1.8.1, EN 301 489-23 v1.4.1, EN 301 489-17 v2.1.1, EN 62311:2008 RADIO SPECTRUM (art 3.2): EN 301 908-1 v4.2.1, EN 301 908-11 v4.2.1, EN 301 893 v1.5.1 ___________________________________ _____________________________________________ ___________________________________________________________________________________________________________________ _____________________________________________________________________________________________________________________________________________________________________________ (Place/Date of issue) (name and signature or equivalent marking of authorized person) Bureau in Europe: Whitehill Way Swindon, UK SN5 6QR FCC Statement This is a CONSUMER device. BEFORE USE, you MUST REGISTER THIS DEVICE with your wireless provider and have your provider’s consent. Most wireless providers consent to the use of signal boosters. Some providers may not consent to the use of this device on their network. If you are unsure, contact your provider. You MUST operate this device with approved antennas and cables as specified by the manufacturer. Antennas MUST be installed at least 20 cm (8 inches) from any person. You MUST cease operating this device immediately if requested by the FCC or a licensed wireless service provider. WARNING. E911 location information may not be provided or may be inaccurate for calls served by using this device. The System and the Outside Antenna (if applicable) must be installed no higher than 10 meters (32’9”) above ground level. Nextivity Incorporated Headquarters: 12230 World Trade Drive, Suite 250 San Diego, CA 92128, USA http://www.nextivityinc.com USER MANUAL Cel-Fi ® with IntelliBoost ™ STOP!!! Do not call your carrier until you have read the Quick Start Guide. If you need more help, try visiting http://www.celfihelp.com Safety Precautions • Install Cel-Fi indoors. It should not be used outdoors. • These products are designed to be used with a direct plug-in power supply unit meeting SELV and “Limited Power Source” (NEC/CEC Class 2) requirements rated 12 Vdc, 1.66 A. When installing the equipment, all the requirements of the manufacturer and the referenced standards must be met. • There are no user serviceable parts inside. CAUTION: Changes or modifications to this product not expressly approved by Nextivity may void your right to operate the equipment. Declaration of Conformity We, Nextivity, Incorporated, 12230 World Trade Drive Suite 250, San Diego, CA 92128, USA declare under our sole responsibility that the product(s): Product Description: Cel-Fi Residential (CELFI-RS2) Models: CELFI-RS218WU and CELFI-RS218CU to which this declaration relate(s) is(are) in conformance with the provisions of Directive 1999/5/EC governing Radio Equipment and Telecommunications Terminal Equipment and the Mutual Recognition of their Conformity using the following standards (CELFI-RS224 and CELFI-RS225 EMC/Radio are covered by FCC/IC requirements): SAFETY (art 3.1.a): EN 60950:2006 /A11:2009 /A1:2010 EMC: (art 3.1.b): EN 301 489-1 v1.8.1, EN 301 489-23 v1.4.1, EN 301 489-17 v2.1.1, EN 62311:2008 RADIO SPECTRUM (art 3.2): EN 301 908-1 v4.2.1, EN 301 908-11 v4.2.1, EN 301 893 v1.5.1 ___________________________________ _____________________________________________ ___________________________________________________________________________________________________________________ _____________________________________________________________________________________________________________________________________________________________________________ (Place/Date of issue) (name and signature or equivalent marking of authorized person) Bureau in Europe: Whitehill Way Swindon, UK SN5 6QR FCC Statement This is a CONSUMER device. BEFORE USE, you MUST REGISTER THIS DEVICE with your wireless provider and have your provider’s consent. Most wireless providers consent to the use of signal boosters. Some providers may not consent to the use of this device on their network. If you are unsure, contact your provider. You MUST operate this device with approved antennas and cables as specified by the manufacturer. Antennas MUST be installed at least 20 cm (8 inches) from any person. You MUST cease operating this device immediately if requested by the FCC or a licensed wireless service provider. WARNING. E911 location information may not be provided or may be inaccurate for calls served by using this device. The System and the Outside Antenna (if applicable) must be installed no higher than 10 meters (32’9”) above ground level. Nextivity Incorporated Headquarters: 12230 World Trade Drive, Suite 250 San…

Text truncated - open the document above for the full version.

Step 1 Find the spot with the best 3G/4G coverage: The first step in setting up your Cel-Fi system is to find the location in your home or office with the best 3G or 4G signal. Use your phone to identify the area with the most bars of signal. Typically, the best service will be near a window in the highest floor of your home or office. Make sure 3G/4G icon is displayed on your handset. Step 2 Plug in the Window Unit: Plug the Window Unit into an easily accessible outlet near the area with the strongest 3G/4G signal. (Note: Both of the power supplies in your kit are identical.) Position the Window Unit so that at least one bar displays on the signal strength indicator on the front of the device. If you do not see at least one bar, try a different location. WINDOW UNIT WINDOW UNIT COVERAGE UNIT Pantone: Black C Pantone: 137C Pantone: 542C T-mobile® Signal Booster RS2 Dual Band For additional information about Signal Booster Installation, please visit: T-Mobile.com > Support > search for “Signal Booster” > select in the drop down window “T-Mobile Cel-Fi Signal Booster” > below “Get Started with Your Device” select “Videos”. Before You Begin. You need one place in your home that gets at least one bar of 4G or LTE cov- erage, one bar of 4G or LTE signal strength, and the revolutionary NEW Cel-Fi RS3-DB system which will bring you blazing fast downloads, smoother video and surfing, and improved voice coverage throughout your home. Cel-Fi is a true plug-and-play system that doesn’t require the installation of anten- nas or cables. IMPORTANT: Your Cel-Fi Signal Booster is electronic equipment. Both units must be kept indoors and in a dry, cool, well ventilated area. In this package you will find: • Window Unit • Coverage Unit • Two Power Adapters If you need additional information on features and services, visit us at www.t-mobile.com or, using an alternate phone, call us at 1-800-937-8997 This is a CONSUMER device. BEFORE USE, you MUST REGISTER ThIS DEVICE with your wireless provider and have your provider’s consent. Most wireless providers consent to the use of signal boosters. Some providers may not consent to the use of this device on their network. If you are unsure, contact your provider. You MUST operate this device with approved antennas and cables as specified by the manufacturer. Antennas MUST be installed at least 20 cm (8 inches) from any person. You MUST cease operating this device immediately if re- quested by the FCC or a licensed wireless service provider. WARNING. E911 location information may not be provided or may be inaccurate for calls served by using this device. When used with any mobile device utilizing the 1710-1755 Mhz band, the FCC limits booster equipment placement to a maximum of 10 meters above ground level. Installation of this equipment which does not comply with federal requirements may subject the owner to FCC enforcement action. NOT FOR RESALE. Coverage is not available everywhere, see coverage details at www.T-Mobile.com. Cel-Fi is a trademark of Nextivity, Inc. T-Mobile and the magenta color are registered trademarks of Deutsche Telekom AG. ©2014 T-Mobile USA, Inc. Changes or modifications not expressly approved by Nextivity, Inc. could void the user’s authority to operate the equipment. NOTE: This equipment has been tested and found to com- ply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to pro- vide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. however, there is no guarantee that interference will not occur in a particular in- stallation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the fol- lowing measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit differ- ent from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV techni- cian for help This Cel-Fi Signal Booster is a T-Mobile-owned device. You will be charged up to $500 if you fail to return the device after termination of your service with T-Mobile, move to a dwelling that has a shared wall (townhouse, duplex, apartment or condo), or return it in a damaged condition. I M P O R T A N T For additional information about Signal Booster Installation, please visit: T-Mobile.com > Support > search for “Signal Booster” > select in the drop down window “T-Mobile Cel-Fi Signal Booster” > below “Get Started with Your Device” select “Videos”. Step 4 Place the Coverage Unit: Move to a location in your home where you need to improve coverage. Plug the Coverage Unit into an easily accessible outlet. After several minutes, the numeric display will stop cycling. If your device is set up properly, the green icon will appear on the display as seen to the left. It is pos- sible to place the Coverage Unit so far away that it can not communicate with the Window Unit. If this happens, a red icon will illuminate indicating that you need to move the Coverage Unit closer to the Window Unit. CEL - FIRS 2 Troubleshooting TOO CLOSE A zero on the numeric display indicates that the Coverage Unit needs to be moved farther away from the Window Unit. GOOD This green icon indicates that the Coverage Unit is functioning normally. TOO FAR This red icon indicates that the Coverage Unit needs to be moved closer to the Window Unit. Step 3 Optimize the Window Unit Placement: The bars on the front of the device indicate the strength of the 3G/4G signal in the area. Moving the Window Unit to a different location in your home may i…

Text truncated - open the document above for the full version.

EMC Test Data Client: Contact: Standard: Test Specific Details General Test Configuration Yes Device complies with Power Density requirements at 20 ti Test Engineer: David Bare Calculation uses the free space transmission formula: S = (PG)/(4 πd 2 ) Where: S is power density (W/m 2 ), P is output power (W), G is antenna gain relative to isotropic, d is separation distance from the transmitting antenna (m). Summary of Results Maximum Permissible Exposure Objective: The objective of this test session is to perform final qualification testing of the EUT with respect to the specification listed above. Date of Test: 12/18/2012 Michiel Lotter FCC parts 15, 24 and 27Class: N/A Nextivity, Inc.Job Number: J89693 Model: CELFI-RS224CU T-Log Number: T89733 Account Manager: Christine Krebill Yes 20cm separation: T89733 Nextivity CelFi-RS224CU.xlsMPE CalcPage 1 of 2 EMC Test Data Client: Contact: Standard: Michiel Lotter FCC parts 15, 24 and 27Class: N/A Nextivity, Inc.Job Number: J89693 Model: CELFI-RS224CU T-Log Number: T89733 Account Manager: Christine Krebill Use: General Used for Multi ple Transmitters Peak AveragedBmWWdBm 2110-2155 WCDMA13.30.013.30.021510.02113.30 5470-5725OFDM16.75.522.20.166710.16622.20 20.18722.73 Power Density (S) @ 20cm (mW/cm^2)0.037 MPE Limit @ 20cm (mW/cm^2) 1.0 Distance at which S > MPE Limit 3.9cm Totals: CU unit (a transmitted "channel" for both WCDMA and OFDM consists of the 3 WCDMA sub channels or the 6 OFDM subchannels respectively All sub channels were present during power measurements ) CU unit (a transmitted "channel" for both WCDMA and OFDM consists of the 3 WCDMA sub channels or the 6 OFDM subchannels respectivel y. All sub channels were present during power measurements.) BandMode Output PowerAntenna gain (Max) EIRPChannels Available Channels Used Total EIRP PeakAveragedBmWWdBm 1930-1990 WCDMA13.10.013.10.020510.02013.10 5470-5725OFDM16.75.522.20.166710.16622.20 20.18622.70 Power Density (S) @ 20cm (mW/cm^2)0.037 MPE Limit @ 20cm (mW/cm^2) 1.0 Distance at which S > MPE Limit 3.9cm Total Power Density (S) @ 20cm (mW/cm^2) 0.074 Totals: subchannels respectively. All sub channels were present during power measurements.) BandMode Output PowerAntenna gain (Max) EIRPChannels Available Channels Used Total EIRP T89733 Nextivity CelFi-RS224CU.xlsMPE CalcPage 2 of 2

File: R90361 Rev. 1 Page 1 of 225 TEST REPORT Covering the DYNAMIC FREQUENCY SELECTION (DFS) REQUIREMENTS OF FCC Part 15 Subpart E (UNII), RSS-210 Annex 9 Nextivity, Inc. Model(s): CELFi-RS224WU and CELFi-RS224CU COMPANY: Nextivity, Inc. 12230 World Trade Drive Suite 250 San Diego, CA, 92128 TEST SITE: NTS Silicon Valley 41039 Boyce Road Fremont, CA 94538 REPORT DATE: December 20, 2012 FINAL TEST DATE: November 19, 20, 2012 TEST ENGINEER: Wayne Fisher PROGRAM MGR / QUALITY ASSURANCE DELEGATE / TECHNICAL REVIEWER: FINAL REPORT PREPARER: ______________________________ ______________________________ David Bare Wayne Fisher Chief Engineer Engineering Team Lead NTS Silicon Valley is accredited by the A2LA, certificate number 0214.26, to perform the test(s) listed in this report, except where noted otherwise. This report and the information contained herein represent the results of testing test articles identified and selected by the client performed to specifications and/or procedures selected by the client. National Technical Systems (NTS) makes no representations, expressed or implied, that such testing is adequate (or inadequate) to demonstrate efficiency, performance, reliability, or any other characteristic of the articles being tested, or similar products. This report should not be relied upon as an endorsement or certification by NTS of the equipment tested, nor does it represent any statement whatsoever as to its merchantability or fitness of the test article, or similar products, for a particular purpose. This report shall not be reproduced except in full NTS Silicon Valley -- EMC Department Test Report Report Date: December 20, 2012 File: R90361 Rev. 1 Page 2 of 225 REVISION HISTORY Rev # Date Comments Modified By 1.0 Initial Release - NTS Silicon Valley -- EMC Department Test Report Report Date: December 20, 2012 File: R90361 Rev. 1 Page 3 of 225 TABLE OF CONTENTS REVISION HISTORY ................................................................................................................................................ 2 TABLE OF CONTENTS ............................................................................................................................................ 3 LIST OF TABLES ....................................................................................................................................................... 3 LIST OF FIGURES ..................................................................................................................................................... 6 SCOPE .......................................................................................................................................................................... 8 OBJECTIVE ................................................................................................................................................................ 8 STATEMENT OF COMPLIANCE ........................................................................................................................... 8 DEVIATIONS FROM THE STANDARD ................................................................................................................ 8 TEST RESULTS .......................................................................................................................................................... 9 TEST RESULTS SUMMARY – FCC PART 15, MASTER DEVICE ..................................................................... 9 MEASUREMENT UNCERTAINTIES .................................................................................................................. 13 EQUIPMENT UNDER TEST (EUT) DETAILS .................................................................................................... 14 GENERAL .............................................................................................................................................................. 14 ENCLOSURE ......................................................................................................................................................... 15 MODIFICATIONS ................................................................................................................................................. 15 SUPPORT EQUIPMENT ....................................................................................................................................... 15 EUT INTERFACE PORTS .................................................................................................................................... 16 EUT OPERATION ................................................................................................................................................. 16 RADAR WAVEFORMS ........................................................................................................................................... 17 DFS TEST METHODS ............................................................................................................................................. 18 RADIATED TEST METHOD ............................................................................................................................... 18 DFS MEASUREMENT INSTRUMENTATION .................................................................................................... 20 RADAR GENERATION SYSTEM ....................................................................................................................... 20 CHANNEL MONITORING SYSTEM .................................................................................................................. 21 DFS MEASUREMENT METHODS ....................................................................................................................... 22 DFS RADAR DETECTION BANDWIDTH ........................................................................................................ 22 DFS – CHANNEL CLOSING TRANSMISSION TIME AND CHANNEL M…

Text truncated - open the document above for the full version.

File: R90358 Page 1 EMC Test Report Application for Grant of Equipment Authorization Industry Canada RSS-Gen Issue 3 / RSS 210 Issue 8 FCC Part 15, Subpart E Model: CELFI-RS224CU FCC ID: YETCELFI-RS224CU IC CERTIFICATION #: 9298A-CRS224CU APPLICANT: Nextivity, Inc. 12230 World Trade Drive Suite 250 San Diego, CA 92128 TEST SITE(S): NTS Silicon Valley 41039 Boyce Road. Fremont, CA. 94538-2435 IC SITE REGISTRATION #: 2845B-3; 2845B-4, 2845B-5, 2845B-7 REPORT DATE: December 20, 2012 FINAL TEST DATES: November 19 and 20, 2012 TOTAL NUMBER OF PAGES: 49 PROGRAM MGR / QUALITY ASSURANCE DELEGATE / TECHNICAL REVIEWER: FINAL REPORT PREPARER: ______________________________ ______________________________ David W. Bare David Guidotti Chief Engineer Senior Technical Writer NTS Silicon Valley is accredited by the A2LA, certificate number 0214.26, to perform the test(s) listed in this report, except where noted otherwise. This report and the information contained herein represent the results of testing test articles identified and selected by the client performed to specifications and/or procedures selected by the client. National Technical Systems (NTS) makes no representations, expressed or implied, that such testing is adequate (or inadequate) to demonstrate efficiency, performance, reliability, or any other characteristic of the articles being tested, or similar products. This report should not be relied upon as an endorsement or certification by NTS of the equipment tested, nor does it represent any statement whatsoever as to its merchantability or fitness of the test article, or similar products, for a particular purpose. This report shall not be reproduced except in full NTS Silicon Valley -- EMC Department Test Report Report Date: December 20, 2012 File: R90358 Page 2 REVISION HISTORY Rev# Date Comments Modified By - First release NTS Silicon Valley -- EMC Department Test Report Report Date: December 20, 2012 File: R90358 Page 3 TABLE OF CONTENTS REVISION HISTORY ................................................................................................................................................ 2 TABLE OF CONTENTS ............................................................................................................................................ 3 SCOPE .......................................................................................................................................................................... 4 OBJECTIVE ................................................................................................................................................................ 5 STATEMENT OF COMPLIANCE ........................................................................................................................... 5 DEVIATIONS FROM THE STANDARDS .............................................................................................................. 5 TEST RESULTS SUMMARY ................................................................................................................................... 6 UNII / LELAN DEVICES ........................................................................................................................................ 6 GENERAL REQUIREMENTS APPLICABLE TO ALL BANDS .......................................................................... 7 MEASUREMENT UNCERTAINTIES .................................................................................................................... 8 EQUIPMENT UNDER TEST (EUT) DETAILS ...................................................................................................... 9 GENERAL ................................................................................................................................................................ 9 OTHER EUT DETAILS ........................................................................................................................................... 9 ENCLOSURE ........................................................................................................................................................... 9 MODIFICATIONS ................................................................................................................................................... 9 SUPPORT EQUIPMENT ......................................................................................................................................... 9 EUT INTERFACE PORTS .................................................................................................................................... 10 EUT OPERATION ................................................................................................................................................. 10 TEST SITE ................................................................................................................................................................. 11 GENERAL INFORMATION ................................................................................................................................. 11 CONDUCTED EMISSIONS CONSIDERATIONS .............................................................................................. 11 RADIATED EMISSIONS CONSIDERATIONS .................................................................................................. 11 MEASUREMENT INSTRUMENTATION ............................................................................................................ 12 RECEIVER SYSTEM ............................................................................................................................................ 12 INSTRUMENT CONTROL COMPUTER ............................................................................................................ 12 LINE IMPEDANCE STABILIZATION NETWORK (LISN) ............................................................................... 12 FILTERS/ATTENUATORS ...........…

Text truncated - open the document above for the full version.