YETCELFI-RS240CUCel-Fi Residential System

Congratulations on your new indoor signal solution. This Cel-Fi system is designed to provide you with significant improvements in coverage as well as 3G data rates. Setting up the system is extremely simple and consists of placing and plugging in two components; a Window Unit and a Coverage Unit. By spending just a few minutes using the instructions in this guide, you can optimize the installation and get the very most from your new Cel-Fi System. If you have any trouble during setup, please use the trouble shooting steps included in this guide. In the package you will find: Window Unit Coverage Unit Two power adapters. CEL - FIRS 2 Quick Start Guide Step 1 Find the spot with the best 3G coverage: The first step in setting up your Cel-Fi system is to find the spot in your home or office that has the best 3G coverage. This is typically by a window, and if you are in a multi-story building, upstairs windows are usually better than downstairs windows. Step 2 Plug in the Window Unit: Take the Window Unit and one power supply out of the box (both power supplies are the same, so grab either one). Plug the Window Unit in, and check to make sure that you can see at least 1 “Bar” on the display in the center of the device. If you do not see at least 1 bar, try a different location. NEED HELP? Visit us at www.celfihelp.com for an installation video and other helpful information regarding installation and trouble shooting. W I N D O W U N I T W I N D O W U N I T C O V E R A G E U N I T COVERAGE UNI T CEL - FIRS 2 Trouble Shooting TOO CLOSE A zero on the numeric display indicates that the “Coverage Unit” needs to be moved farther away from the “Window Unit”. GOOD This green icon indicates that the “Coverage Unit” is functioning normally. TOO FAR This red icon indicates that the “Coverage Unit” needs to be moved closer to the “Window Unit”. Step 3 Optimize the Window Unit Placement The number of bars you can see on the Window Unit make a significant difference in the operation of the Cel-Fi system. Try moving the Window Unit to a couple of different spots to see if you can get better signal; the more bars the better. Step 5 Optimize The Coverage Unit Placement The farther away you place the coverage unit from the Window unit the better the coverage in your home, so put the Coverage Unit as far away from the Window Unit as possible. The number shown on the side of the display gives you an indication as to the quality of the placement. Test two or three locations and for best results; try and get a 7, 8 or 9 on the display. Indicator No lights on “Window Unit” display. Status indicator is flashing green for mo re than a minute. Status indicator is flashing red. Status indicator is on solid red. No se gment lit on signal display and status indicator on solid green. Problem There is no power. The “Window Unit” unit is attempting to complete regulatory compliance. Error Code on ”Coverage Unit”. Ha rdware Error. Not receiving cell signal. Try This 1. Is the unit plugged in? 2. Is the re power at the outlet? 3. Try exchanging the power supplies with the “Coverage Unit” to see if the power supply is defective. 1. Wait for the status indicator to stop flashing, this could take several minutes. 1. See the “Coverage Unit” to determine what error code is being displayed. 1. Try resetting the “Window Unit” by unplugging it and then plugging it back in. 2. If problem persists return system for service/replacement. 1. Try moving the “Window Unit” to another room or area where you have more coverage. (Use your cell phone to find the best 3G coverage). Indicator E1 E3 E4 Problem No Signal on “Window Unit”. ”Coverage Unit” is overheating. “Window Unit” is overheating. Try This Try moving the “Window Unit” to another room or area where you have coverage. (Use your cell phone to find the best 3G coverage). Make sure that the vents on the unit are not blocked. Move the unit to a cooler area. The system will start working normally when it cools down. Indicator No lights on ”Coverage Unit” display. 7 se gment display is cycling for more than a minu te. 7 se gment display shows a value of 0. Red “Too Far” Indicator. Red Status Indicator. Problem There is no power. The ”Coverage Unit” is taking longer than no rmal to make a link. The ”Coverage Unit” is “Too Close” to the “Window Unit”. The ”Coverage Unit” is “Too Far” from the “Window Unit” Ha rdware Error. Try This 1.Is the unit plugged in? 2. Is the re power at the outlet? 3. Try exchanging the power supplies with the “Window Unit” to see if the power supply is defective. 1. Wait for the display to stop cycling, this could take several minutes 2. Move away from WiFi devices. 1. Move the ”Coverage Unit” further away from the “Window Unit”. 1. Move the ”Coverage Unit” closer to the “Window Unit”. 1. Try resetting the ”Coverage Unit” by unplugging it and then plugging it back in. 2. If problem persists return system for service. WIND OW UNI T COVERAGE UNI T ERROR MESS AGES W I N DO W U N I T Step 4 Place the Coverage Unit Move to a location in your home where you need to have improved coverage. Plug the Coverage unit in and wait until the numeric display stops cycling, this could take several minutes. At this point you should see a green icon indicating that the unit is working properly. It is possible to place the Coverage Unit so far away that it cannot communicate with the Window Unit. If this happens, a red icon will illuminate indicating that you need to move the Coverage Unit closer to the Window unit. 420N003-001-001-10R51

Cel-Fi TM with IntelliBoost TM Nextivity Incorporated Headquarters: 12230 World Trade Drive Suite 250 San Diego, CA 92128, USA http://www.nextivityinc.com European Office: Whitehill Way Swindon, UK SN5 6QR Cel-Fi TM with IntelliBoost TM Nextivity Incorporated Headquarters: 12230 World Trade Drive Suite 250 San Diego, CA 92128, USA http://www.nextivityinc.com European Office:Whitehill Way Swindon, UK SN5 6QR STOP!!! Do not call your carrier until you have read the Quick Start Guide. If you need more help, try visiting http://www.celfihelp.com Safety Precautions • Install Cel-Fi indoors. It should not be used outdoors. • This product is designed to be used with the provided power supply. It is a listed direct plug-in power unit marked “Class 2” and rated 12 Vdc, minimum 1.25A. • There are no user serviceable parts inside. STOP!!! Do not call your carrier until you have read the Quick Start Guide. If you need more help, try visiting http://www.celfihelp.com Safety Precautions • Install Cel-Fi indoors. It should not be used outdoors. • This product is designed to be used with the provided power supply. It is a listed direct plug-in power unit marked “Class 2” and rated 12 Vdc, minimum 1.25A. • There are no user serviceable parts inside. Caution: Changes or modifications to this product not expressly approved by Nextivity may void your right to operate the equipment. Caution: Changes or modifications to this product not expressly approved by Nextivity may void your right to operate the equipment. For models CELFI-RS240WU and CELFI-RS240CU: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired o p eration. For models CELFI-RS240WU and CELFI-RS240CU: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired o p eration. Limited Warranty; Warranties This Cel-Fi (Product) is distributed by your mobile carrier, and depending on their terms and conditions of sale, you may or may not have additional rights under a warranty program for Cel-Fi. This does not affect your statutory rights. All Products must be stored, carried, processed, installed or otherwise handled or dealt with by End User and its agents in accordance with Nextivity’s published instructions, and in accordance with normal safety procedures for the handling of Products, and Nextivity shall not be liable for any loss, damage, injury or expense arising out of the Products or their condition if this is not done. Nextivity shall not be liable to replace any Products rejected only on the grounds of immaterial imperfections or variations in the manufacturing process. THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES WITH RESPECT TO THE PRODUCTS AND ANY DOCUMENTATION OR OTHER MATERIALS PROVIDED BY NEXTIVITY, EITHER EXPRESSED OR IMPLIED, INCLUDING ANY IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR ANY PARTICULAR PURPOSE, AND NONINFRINGEMENT, ALL OF WHICH ARE HEREBY DISCLAIMED. WITHOUT LIMITING THE FOREGOING, NEXTIVITY. DOES NOT WARRANT THAT THE HARDWARE WILL WORK PROPERLY IN ALL ENVIRONMENTS AND APPLICATIONS, NO PERSON IS AUTHORIZED TO REPRESENT, PROMISE OR ASSUME ANY OBLIGATION OR LIABILITY CONTRARY OR IN ADDITION TO THIS WARRANTY. Limitation of Liability In no event shall Nextivity, nor its directors, employees, agents, suppliers or End Users, be liable under contract, tort, strict liability, negligence or any other legal or equitable theory with respect to the Products or any other subject matter of this Agreement (i) for any lost profits, cost of procurement of substitute goods or services, or special, indirect, incidental, punitive, or consequential damages of any kind whatsoever or (ii) for any direct damages in excess of (in the aggregate) the fees actually received by Nextivity from End User with respect to the Products actually purchased and paid for. Intellectual Property End User agrees not to copy any product or process of Nextivity, or any part thereof, except with the express, prior written consent of Nextivity, given in its sole discretion. All risks of direct or indirect patent infringement are assumed by the End User. Nothing shall be construed as recommendation to make, use, or sell any Product or process in conflict with existing or future patents. End User shall not (and End User shall not permit anyone else to): (i) in any way reverse engineer or otherwise attempt to derive any source code or underlying ideas or algorithms from any part of the Products, except to the limited extent applicable laws specifically prohibit such restriction, (ii) modify, translate, or otherwise create derivative works of any part of the Products, or (iii) copy, rent, lease, distribute, or otherwise transfer any of the rights that End User receives hereunder. End User shall abide by all applicable local, state, national and international laws and regulations. Miscellaneous Cel-Fi, IntelliBoost, and Nextivity logo are trademarks of Nextivity, Inc. Copyright © 2011 by Nextivity, Inc. U.S. Patent 7,519,323 and other Patents Pending. All Rights Reserved. Reproduction or media conversion by any means is protected by copyright and may only occur with prior written permission of Nextivity. Declaration of Conformity We, Nextivity, Incorporated, 12230 World Trade Drive Suite 250, San Diego, CA 92128, USA declare under our sole responsibility that the product(s): Product Description: Cel-Fi Residential (CELFI-RS2) Models: CELFI-RS210WU and CELFI-RS210CU, CELFI-RS250WU and CELFI-RS250CU to which this declaration relate(s) is(are) in conformanc e with the provisions of Directive 1999/5/EC governing Radio Equipment and Telecommunications Termin…

Text truncated - open the document above for the full version.

Cel-Fi TM with IntelliBoost TM Nextivity Incorporated Headquarters: 12230 World Trade Drive Suite 250 San Diego, CA 92128, USA http://www.nextivityinc.com European Office:Whitehill Way Swindon, UK SN5 6QR Cel-Fi TM with IntelliBoost TM Nextivity Incorporated Headquarters: 12230 World Trade Drive Suite 250 San Diego, CA 92128, USA http://www.nextivityinc.com European Office:Whitehill Way Swindon, UK SN5 6QR STOP!!! Do not call your carrier until you have read the Quick Start Guide. If you need more help, try visiting http://www.celfihelp.com Safety Precautions • Install Cel-Fi indoors. It should not be used outdoors. • This product is designed to be used with the provided power supply. It is a listed direct plug-in power unit marked “Class 2” and rated 12 Vdc, minimum 1.25A. • There are no user serviceable parts inside Caution: Changes or modifications to this product not expressly approved by Nextivity may void your right to operate the equipment. Declaration of Conformity We, Nextivity, Incorporated, 12230 World Trade Drive Suite 250, San Diego, CA 92128, USA declare under our sole responsibility that the product(s): Product Description: Cel-Fi Residential (CELFI-RS2) Models: CELFI-RS210WU and CELFI-RS210CU, CELFI-RS250WU and CELFI-RS250CU to which this declaration relate(s) is(are) in conformance with the provisions of Directive 1999/5/EC governing Radio Equipment and Telecommunications Terminal Equipment and the Mutual Recognition of their Conformity using the following standards: SAFETY (art 3.1.a): EN 60950:2006 /A11:2009 /A1:2010 EMC: (art 3.1.b): EN 301 489-1 v1.8.1, EN 301 489-23 v1.4.1, EN 301 489-17 v2.1.1, EN 62311:2008, SAR Touch Safe RADIO SPECTUM (art 3.2): EN 301 908-1 v4.2.1, EN 301 908-11 v4.2.1, EN 301 893 v1.5.1 _________________________________________________________________________________________________________ _______________________________________________________________________________________________________________________________ ___________________________________________ (Place/Date of issue) (name and signature or equivalent marking of authorized person) STOP!!! Do not call your carrier until you have read the Quick Start Guide. If you need more help, try visiting http://www.celfihelp.com Safety Precautions • Install Cel-Fi indoors. It should not be used outdoors. • This product is designed to be used with the provided power supply. It is a listed direct plug-in power unit marked “Class 2” and rated 12 Vdc, minimum 1.25A. • There are no user serviceable parts insideCaution: Changes or modifications to this product not expressly approved by Nextivity may void your right to operate the equipment. Declaration of Conformity We, Nextivity, Incorporated, 12230 World Trade Drive Suite 250, San Diego, CA 92128, USA declare under our sole responsibility that the product(s): Product Description: Cel-Fi Residential (CELFI-RS2) Models: CELFI-RS210WU and CELFI-RS210CU, CELFI-RS250WU and CELFI-RS250CU to which this declaration relate(s) is(are) in conformance with the provisions of Directive 1999/5/EC governing Radio Equipment and Telecommunications Terminal Equipment and the Mutual Recognition of their Conformity using the following standards: SAFETY (art 3.1.a): EN 60950:2006 /A11:2009 /A1:2010 EMC: (art 3.1.b): EN 301 489-1 v1.8.1, EN 301 489-23 v1.4.1, EN 301 489-17 v2.1.1, EN 62311:2008, SAR Touch Safe RADIO SPECTUM (art 3.2): EN 301 908-1 v4.2.1, EN 301 908-11 v4.2.1, EN 301 893 v1.5.1 _________________________________________________________________________________________________________ _______________________________________________________________________________________________________________________________ ___________________________________________ (Place/Date of issue) (name and signature or equivalent marking of authorized person) Limited Warranty; Warranties This Cel-Fi (Product) is distributed by your mobile carrier, and depending on their terms and conditions of sale, you may or ma y not have additional rights under a warranty program for Ce l-Fi. This does not affect your statutory rights. All Products must be stored, carried, processed, installed or otherwise handled or dealt with by End User and its agents in accordance with Nextivity’s published instructions, and in accordance with normal safety procedures for the handling of Product s, and Nextivity shall not be liable for any loss, damage, injury or expense arising out of the Products or their condition if this is not done. Nextivity shall not be liable to replace any Products rejected only on the grounds of immaterial imperfections or variations in the manufacturing process. THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES WITH RESPECT TO THE PRODUCTS AND ANY DOCUMENTATION OR OTHER MATERIALS PROVIDED BY NEXTIVITY, EITHER EXPRESSED OR IMPLIED, INCLUDING ANY IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR ANY PART ICULAR PURPOSE, AND NONINFRINGEMENT, ALL OF WHICH ARE HEREBY DISCLAIMED. WITHOUT LIMITING THE FOREGOING, NEXTIVITY. DOES NOT WARRANT THAT THE HARDWARE WILL WORK PROPERLY IN ALL ENVIRONMENTS AND APPLICATIONS, NO PERSON IS AUTHORIZED TO REPRESENT, PROMISE OR ASSUME ANY OBLIGATION OR LIABILITY CONTRARY OR IN ADDITION TO THIS WARRANTY. Limitation of Liability In no event shall Nextivity, nor its directors, employees, agents, suppliers or End Users, be liable under contract, tort, str ict liability, negligence or any other legal or equitable theory with respect to the Products or any other subject matter of this Agreement (i) for any lost profits, cost of procurement of substitute goods or services, or special, indirect, incidental, punitive, or consequential damages of any kind whatsoever or (ii) for any direct damages in excess of (in the aggregate) the fees actually received by Nextivity from End User with respect to the Products actually purchased and paid for. Intellectual Property End User agrees not to copy any product or process of Nextivity, or any part thereof, except with t…

Text truncated - open the document above for the full version.

Nextivity Incorporated 12230 World Trade Drive, Suite 250 San Diego, CA, U.S.A Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 10/14/2011 Dear Examiner: I am writing to avoid the possibility of an inadvertent disclosure of proprietary information. The accompanying Form 731 is being filed with the commission on our behalf by Elliott Laboratories, Inc., a consulting and testing laboratory. Included as exhibits with the enclosed application are block diagrams, BOMs, schematics, and a detailed description of the theory of operation of the device. It is our intention to provide the commission with a full disclosure of our product so that its merits can be evaluated. Indeed, we are pleased to provide any further information that the commission might wish to see. It is not our intention, however, to make our proprietary process a matter of public record. In view of the fact that the block diagrams, BOMs, schematics, and associated theory of operation disclose the mechanism of our process, we ask that these portions of our application be withheld from public inspection as provided under FCC section 0.459: • Block diagrams • BOMs • Schematics • Theory of operation These documents contain details of the proprietary operation of product. These details are not readily discernible - even to technically sophisticated individuals - from our hardware and constitute trade secrets. We request therefore that these documents be segregated from the body of our evaluation report and withheld from public inspection. Thank you for your attention. Please let the undersigned know if the Commission disagrees with our position or requires further justification. Sincerely, Michiel Lotter V.P. Engineering, Nextivity

Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 Date: 10/14/2011 FCC ID: YETCELFI-RS240WU and YETCELFI-RS240CU Gentlemen: This is your letter of authorization to accept our appointment of Elliott Laboratories, Inc. as Agent for Nextivity Incorporated, 12230 World Trade Drive, Suite 250, San Diego, CA, U.S.A, to sign applications before the Commission and to make representations to you on our behalf. Elliott Laboratories is to receive and exchange data between our company and the Commission. This authorization is made pursuant to Section 2.911(c) of the FCC Rules and expires on 4/14/2012. I hereby certify on behalf of Nextivity Incorporated, 12230 World Trade Drive, Suite 250, San Diego, CA, U.S.A. ("Applicant") that neither Applicant nor any party to the application (officers, directors, and 5% shareholders) is subject to a denial of Federal benefits that includes FCC benefits pursuant to section 5301 of the Anti-Drug Abuse Act of 1988. 21 U.S.C. 853a. Sincerely, Michiel Lotter V.P. Engineering, Nextivity

Page 1 of 1 November 9, 2011 FCC RE: YETCELFI-RS240WU, EA272711 YETCELFI-RS240WU, EA579500 YETCELFI-RS240CU, EA902503 YETCELFI-RS240CU, EA218975 To Whom It May Concern: Please supersede the user manual file “420N003-002-001-10R_FCCpending.pdf”. Nextivity provided “420N003-002-001-10R51_pending.pdf” as an updated version Sincerely, David Guidotti Senior Technical Writer

Back Bottom Front Side Top

Label Location on Product Actual Size (2”w x 1.5”h): . Enlarged view:

Back 1 Back 2 Bareboard Back1 Bareboard Back2 Bareboard Front1 Bareboard Front2 Baseband Cell Ant Cell Clock Front1 Front 2 Interface Memory Power UNII RX UNII RX1 ant UNII RX2 ant UNII TX Ant UNII TX

EMC Test Data Client: Contact: Standard: Test Specific Details General Test Configuration Yes Device complies with Power Density requirements at 20 ti David Bare Calculation uses the free space transmission formula: S = (PG)/(4 πd 2 ) Where: S is power density (W/m 2 ), P is output power (W), G is antenna gain relative to isotropic, d is separation distance from the transmitting antenna (m). Summary of Results Maximum Permissible Exposure Objective: The objective of this test session is to perform final qualification testing of the EUT with respect to the specification listed above. Date of Test: 10/31/2011 Test Engineer: Rama Akella FCC Part 15, 27Class: N/A Nextivity Inc.Job Number: J84755 Model: CELFI-RS240WU T-Log Number: T84761 Account Manager: Sheareen Washington Yes 20cm separation: T84761 WU.xlsMPE CalcPage 1 of 2 EMC Test Data Client: Contact: Standard: Rama Akella FCC Part 15, 27Class: N/A Nextivity Inc.Job Number: J84755 Model: CELFI-RS240WU T-Log Number: T84761 Account Manager: Sheareen Washington Use: General Used for Multi ple Transmitters CU unit Peak AveragedBmWWdBm 2110-2155 WCDMA13.50.013.50.02221110.02213.50 5470-5725OFDM17.45.522.90.195710.19522.90 20.21723.37 Power Density (S) @ 20cm (mW/cm^2)0.043 MPE Limit @ 20cm (mW/cm^2) 1.0 Distance at which S > MPE Limit 4.2cm WU unit PeakAveragedBmWWdBm Total EIRP Channels Available Channels Used Total EIRP Totals: BandMode Output PowerAntenna gain (Max) EIRPChannels Available EIRP Channels Used BandMode Output PowerAntenna gain (Max) PeakAveragedBmWWdBm 1710-1755 WCDMA20.94.425.30.33921110.33925.30 5150-5350OFDM17.45.522.90.193510.19322.85 20.53227.26 Power Density (S) @ 20cm (mW/cm^2)0.106 MPE Limit @ 20cm (mW/cm^2) 1.0 Distance at which S > MPE Limit 6.5cm Totals: gain (Max)AvailableUsed T84761 WU.xlsMPE CalcPage 2 of 2

File: R85099 Page 1 Radio Test Report FCC Part 27 & RSS-139 (2110 MHz to 2155 MHz) Model: CELFI-RS240CU IC CERTIFICATION #: 9298A-CRS240CU FCC ID: YETCELFI-RS240CU COMPANY: Nextivity Inc. 12230 World Trade Drive Suite 250 San Diego, CA 92128 TEST SITE(S): Elliott Laboratories 41039 Boyce Road. Fremont, CA. 94538-2435 REPORT DATE: November 3, 2011 FINAL TEST DATES: October 4 and 10, 2011 TOTAL NUMBER OF PAGES: 38 PROGRAM MGR / QUALITY ASSURANCE DELEGATE / TECHNICAL REVIEWER: FINAL REPORT PREPARER: ______________________________ ______________________________ David W. Bare David Guidotti Chief Engineer Senior Technical Writer Elliott Laboratories is accredited by the A2LA, certificate number 2016.01, to perform the test(s) listed in this report, except where noted otherwise. This report and the information contained herein represent the results of testing test articles identified and selected by the client performed to specifications and/or procedures selected by the client. National Technical Systems (NTS) makes no representations, expressed or implied, that such testing is adequate (or inadequate) to demonstrate efficiency, performance, reliability, or any other characteristic of the articles being tested, or similar products. This report should not be relied upon as an endorsement or certification by NTS of the equipment tested, nor does it represent any statement whatsoever as to its merchantability or fitness of the test article, or similar products, for a particular purpose. This report shall not be reproduced except in full. Elliott Laboratories -- EMC Department Test Report Report Date: November 3, 2011 File: R85099 Page 2 REVISION HISTORY Rev# Date Comments Modified By - 11-3-2011 First release Elliott Laboratories -- EMC Department Test Report Report Date: November 3, 2011 File: R85099 Page 3 TABLE OF CONTENTS REVISION HISTORY ................................................................................................................................................2 TABLE OF CONTENTS ............................................................................................................................................3 SCOPE..........................................................................................................................................................................4 OBJECTIVE ................................................................................................................................................................5 STATEMENT OF COMPLIANCE...........................................................................................................................5 DEVIATIONS FROM THE STANDARDS ..............................................................................................................5 TEST RESULTS..........................................................................................................................................................6 FCC PART 27 & RSS-139 (2110 – 2155 MHZ ADVANCED WIRELESS SERVICE) ...............................................6 EXTREME CONDITIONS ......................................................................................................................................7 MEASUREMENT UNCERTAINTIES....................................................................................................................7 EQUIPMENT UNDER TEST (EUT) DETAILS ......................................................................................................8 GENERAL................................................................................................................................................................8 OTHER EUT DETAILS...........................................................................................................................................8 ENCLOSURE...........................................................................................................................................................8 MODIFICATIONS...................................................................................................................................................8 SUPPORT EQUIPMENT.........................................................................................................................................8 EUT INTERFACE PORTS ......................................................................................................................................9 EUT OPERATION ...................................................................................................................................................9 TESTING ...................................................................................................................................................................10 GENERAL INFORMATION .................................................................................................................................10 RF PORT MEASUREMENT PROCEDURES ......................................................................................................11 OUTPUT POWER..................................................................................................................................................11 BANDWIDTH MEASUREMENTS ......................................................................................................................12 CONDUCTED SPURIOUS EMISSIONS..............................................................................................................12 TRANSMITTER MASK MEASUREMENTS.......................................................................................................13 FREQUENCY STABILITY ...................................................................................................................................13 TRANSIENT FREQUENCY BEHAVIOR:...........................................................................................................13 RA…

Text truncated - open the document above for the full version.

File: R85135 Rev. 1 Page 1 of 191 TEST REPORT Covering the DYNAMIC FREQUENCY SELECTION (DFS) REQUIREMENTS OF FCC Part 15 Subpart E (UNII) Nextivity Inc. Model(s): CELFI-RS240CU and CELFI-RS240WU IC CERTIFICATION #: 9298A-CRS240CU & 9298A-CRS240WU FCC ID: YETCELFI-RS240CU & YETCELFI-RS240WU COMPANY: Nextivity Inc. 12230 World Trade Drive Suite 250 San Diego, CA, 92128 TEST SITE: Elliott Laboratories 41039 Boyce Road Fremont, CA 94538 REPORT DATE: November 3, 2011 FINAL TEST DATE: October 7 and 18, 2011 TEST ENGINEER: David Bare AUTHORIZED SIGNATORY: ______________________________ Wayne Fisher Engineering Team Lead This report and the information contained herein represent the results of testing test articles identified and selected by the client performed to specifications and/or procedures selected by the client. National Technical Systems (NTS) makes no representations, expressed or implied, that such testing is adequate (or inadequate) to demonstrate efficiency, performance, reliability, or any other characteristic of the articles being tested, or similar products. This report should not be relied upon as an endorsement or certification by NTS of the equipment …

Text truncated - open the document above for the full version.