YH9NXBTRBluetooth Low Energy Radio

NX ™ Bluetooth ® Radio Module INSTALLATION INSTRUCTIONS 9601 Dessau Road, Building One | Austin, TX 78754 Toll Free: 888-698-3242 | Fax: 512-450-1215 | www.hubbell-automation.com3454B 12.1.2015 PRECAUTIONS • Read and understand all instructions before beginning installation. SAVE THESE INSTRUCTIONS! DESCRIPTION The Hubbell Building Automation NXBTR Bluetooth Radio Module enables wireless communication with one group of Room Controller(s), Sensor(s), and Switches using a Smart Phone or other Bluetooth enabled hand held device. In conjunction with an App based user interface, the user can manually control the room loads and/or perform set up and configuration. INSTALLATION 1. Plug the Bluetooth radio module into a Smart Port on the Room Controller or a Smart Switch. Make certain that you hear a distinct “click” as the RJ-45 connector locks into the socket. 2. If the Bluetooth module is being installed behind a Smart Switch, be careful to guide the module into the clear space in the box behind the switch as the screws are tightened. 3. Contact HBA Technical Support for instructions on obtaining and installing the Smart Phone App 4. When the App is started, any modules in range will be discovered and appear on the screen. If several modules are installed, it is likely that you will discover more than one. Each discovered room will include a signal strength indicator. This can be useful in identifying the local room. 5. Touch the room to which you wish to connect. 6. Consult the NX Smart Phone Wireless App Operation Guide for instructions on using the App to set up and configure the lighting controls in the zone. FCC ID: YH9NXBTR IC: 9044A-NXBTR Federal Communications Commission (FCC) statement (USA) This device meets the FCC requirements for RF exposure in public or uncontrolled environments. This device complies with FCC part 15 FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference and 2. This device must accept any interference received, including interference that may cause undesired operation FCC Warning Changes or modifications not approved by Hubbell Control Solutions could void the user’s authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a commercial installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. IC Warning This device complies with Industry Canada license exempt RSS standard(s). Operation is subject to the following two conditions: 1. this device may not cause interference, and 2. this device must accept any interference, including interference that may cause undesired operation of the device. Cet appareil est conforme avec Industrie Canada RSS standard exempts de licence (s). Son utilisation est soumise à Les deux conditions suivantes: 1. cet appareil ne peut pas provoquer d’interférences et 2. cet appareil doit accepter Toute interférence, y compris les interférences qui peuvent causer un mauvais fonctionnement du dispositive. The Bluetooth ® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by Hubbell Building Automation is under license. Other trademarks and trade names are those of their respective owners. 72-00544 Rev. B

Thisauthorizationexpireson May31, 2016. \ -I"." <E[~~~BuildingAutomation,Inc. November23, 2015 BABTFCB ForsythHouse, ChurchfieldRoad, Walton-on-Thames, Surrey, KT122TD DearSir or Madam, We,HubbellBuildingAutomation,Inc. locatedat 9601DessauRoad,BuildingOneSuite100,Austin, Texas78754herebyauthorizeEric Lifsey,ProfessionalTesting(EMf)Inc.,Tel. (512)244-3371,to act as our agentin all mattersrelatingto applicationsfor equipmentauthorization,includingthe signingof all documentsrelatingto thesematters. Sincerely, ~fAJ~ CompanyOfficer:Eric Weber,Directorof Engineering TelephoneNumber: (512)719-7407 Email: [email protected] HubbellBuildingAutomation 9601DessauRoad,BuildingOne,Suite100,AustinTexas,78754USA PH:888-698-3242FX:877-783-9201www.hubbell-automation.com

Exhibit BlockDiagrams' ExternalPhotos InternalPhotos OperationDescriptionor Theoryof Operation' PartsList& PlacementDiagrams,BOM 2 Tune-UpProcedure Schematics' TestSetupPhotos User'sManual ~~@eUildingAutomation,Inc. i November23,2015 TUVSUOBABTFCB OctagonHouse, SegensworthRoad, Fareham, Hampshire, P0155RL FCCID: YH9NXBTR ConfidentialityRequest Pursuantto Sections0.457(d)(1)(ii) and 0.459of the Commission'sRules,HubbellBuildingAutomation, Inc.herebyrequestspermanentconfidentialtreatmentof informationaccompanyingthis applicationas listedbelow: Typeof ConfidentialityRequested o ShortTerm 3 [gIPermanent o ShortTerm 3 ' o ShortTerrrr'0Permanent=' o ShortTerm 3 [gIPermanent o ShortTerm 3 I2J Permanent o ShortTerm 3 0Permanent o ShortTerm 3 I2J Permanent o ShortTerm 3 o ShortTerm 3 oPermanent* The abovematerialscontaintradesecretsand proprietaryinformationnot customarilyreleasedto the public.The publicdisclosureof thesemattersmightbe harmfulto the Applicantand provideunjustified benefitsto its competitors. The Applicantunderstandsthat pursuantto Rule0.457(d)(1)(ii), disclosureof this Applicationand all accompanyingmaterialswill not be madebeforethe dateof the Grantfor this Application. Y8i:,'eI Y ' Directorof Engineering Telephone:(512)719-7407 Email:[email protected] 1 _ Theasteriskeditems(*) requirefurtherjustificationbeforepermanentconfidentialitywillbe allowed.Thesealsocurrently .requirereviewby theFCCundertheirPermit-But-Askpolicybeforethegrantis issuedandcandelaycompletionof an application.Furtherjustificationshouldbe addedto thenoteabove.Onesuchexamplefor a potteddevicewouldbe:"TheBUT is FULLYpottedusinga non-removableepoxybasedmaterial.Removalof pottingmaterialcausesirreparabledamageto internalcircuitry.Seephotographsexhibitsthatoutlinethedevicebeforeandafterpotting." 2_Theseitemsrequireno additionaljustificationto be heldconfidentialbutmustbe requestedregardless.NotethatmostPart15 devicedo notrequirea tune-upprocedure.If no tune-upprocedureis required,thendo notcheckthetune-upprocedurebox. 3_Theseitemsareuniqueto theFCConlyandrequireadditionalfees.It allowsfor keepingall itemsconfidentialuntilproduct beginsshipping.OnceproductstartsshippingthenBABTmustbe notifiedto canceltheshorttermconfidentiality. HubbellBuildingAutomation 9601DessauRoad,BuildingOne,Suite100,AustinTexas,78754USA PH:888-698-3242FX:877-783-9201www.hubbell-automation.com

17666 External Photos Page 1 of 2 Side 1: Top/Label Side 2: Back Side 3: Left Side 4: Right 17666 External Photos Page 2 of 2 Side 5: End Side 6: Cable End ***

17666 Label and Location Page 1 of 1 ***

17666 Internal Photos Page 1 of 2 Component Side Back Side with Radio Module Attached Radio Module Back and Top 17666 Internal Photos Page 2 of 2 Main Board Component Side Main Board with Radio Module ***

17666 Exposure Supplemental Report Page 1 of 2 Professional Testing (EMI) Inc. 1601 North A.W. Grimes Blvd., Suite B Round Rock, TX 78665 e-mail: [email protected] (512) 244-3371 Fax: (512) 244-1846 1.0 Maximum Permissible Exposure Evaluation (Supplements the test report.) The measured power is considered for the intended use of the device and resulting RF exposure to the user. 1.2 Criteria Section Reference Date KDB 447498 D01 Mobile Portable RF Exposure v05r01 // RSS‐102 Issue 5 March 2015, Notice 2013 DRS0911 23 Nov 2015 1.3 Procedure Using measurement of peak power and considering the intended application, determine the permissible exposure level, applicability of exclusion, or whether additional exposure tests (SAR) are indicated. When applicable justify conclusion for selected exposure level and separation distance. 1.4 Power to Exposure Calculation For 2.4 GHz radio power is determined by radiated field measurement. SAR exemption method was applied for 200 mm spacing; this was based on that contact with the module is not required for operation and the device is entirely supported by the host system. Table 1.4.1 Power Calculation for Exposure, 2.4 GHz Radio (Highest frequency 2.480 GHz) Measured Radiated Power mW Calculated Peak EIRP dBm Source Duty Cycle Factor dB Antenna Gain dBi Calculated EIRP dBm EIRP In Linear Terms mW 2.9 4.6 ‐2.07 0* 2.53 1.8 *Effect of antenna gain included in the field strength measurement. 1.5 SAR Exemption Calculation – FCC Applicable requirement: KDB 447498 Clause 4.3.1 Section 1 Calculation (max power including tune up tolerance = 1.8 mW): [(1.8 mW)/(200 mm)] · [√2.480 (GHz)] = 0.45 0.45 ≤ 3.0 Therefore, the device meets the applicable FCC SAR exemption requirements. 17666 Exposure Supplemental Report Page 2 of 2 Professional Testing (EMI) Inc. 1.6 SAR Exemption Calculation – IC This device meets the clause 2.5 Exemption Limits for Routine Evaluation – SAR Evaluation criteria in RSS-102 Clause 2.5.1, Table 1, for frequency row 2450 MHz. This is based on the output power of 1.8 mW being less than 4 mW at the smallest exposure distance given of ≤5 mm in Table 1. Signed: Eric Lifsey ***

Project 17666-15 Hubbell Building Automation NXBTR Wireless Certification Report Prepared for: Eric Weber Hubbell Building Automation 9601 Dessau Road Building 1 Austin, TX 78754 By Professional Testing (EMI), Inc. 1601 North A.W. Grimes Blvd., Suite B Round Rock, Texas 78665 30 Nov 2015 Reviewed by Written by Larry Finn Chief Technical Officer Eric Lifsey EMC Engineer Hubbell Building Automation – NXBTR 17666 Professional Testing (EMI) Inc. Page 2 of 50 Revision History Revision Number Description Date 00 Draft for client and internal review. 23 Nov 2015 01 Revised per reviewer comments, revised address. 30 Nov 2015 Corrections: None. Hubbell Building Automation – NXBTR 17666 Professional Testing (EMI) Inc. Page 3 of 50 Table of Contents Revision History ............................................................................................................................................................. 2 Compliance Certificate .................................................................................................................................................. 5 1.0 Introduction .......................................................................................................................................................... 6 1.1 Scope ............................................................................................................................................................... 6 1.2 EUT Description ............................................................................................................................................. 6 1.3 EUT Operation ................................................................................................................................................ 6 1.4 Modifications to Equipment ............................................................................................................................ 6 1.5 Test Site .......................................................................................................................................................... 7 1.6 Radiated Measurements .................................................................................................................................. 7 1.7 Applicable Documents and Clauses ................................................................................................................ 7 2.0 Fundamental Power and Duty Cycle ................................................................................................................... 8 2.1 Test Procedure ................................................................................................................................................ 8 2.2 Test Criteria .................................................................................................................................................... 8 2.3 Test Results, Peak Power ................................................................................................................................ 8 2.4 Test Results, Duty Cycle ................................................................................................................................. 9 3.0 Power Spectral Density ...................................................................................................................................... 11 3.1 Test Procedure .............................................................................................................................................. 11 3.2 Test Criteria .................................................................................................................................................. 11 3.3 Test Results ................................................................................................................................................... 11 4.0 Occupied Bandwidth .......................................................................................................................................... 12 4.1 Test Procedure .............................................................................................................................................. 12 4.2 Test Criteria .................................................................................................................................................. 12 4.3 Test Results ................................................................................................................................................... 12 4.3.1 Bandwidth Plots, 6 dB ......................................................................................................................... 13 4.3.2 Bandwidth Plots, 20 dB ....................................................................................................................... 15 5.0 Band Edge .......................................................................................................................................................... 17 5.1 Test Procedure .............................................................................................................................................. 17 5.2 Test Criteria .................................................................................................................................................. 17 5.3 Test Results ................................................................................................................................................... 17 5.3.1 Low Channel Band Edge ..................................................................................................................... 18 5.3.2 High Channel Band Edge .................................................................................................................... 20 6.0 Radiated Spurious Emissions, Receive Mode .................................................................................................... 22 6.1 Test Procedure…

Text truncated - open the document above for the full version.

17666 Setup Photographs Page 1 of 2 Radiated Emissions, Front Radiated Emissions, Back 17666 Setup Photographs Page 2 of 2 Radiated Emissions, EUT Bandwidth and Duty Cycle ***