YH9NXSMDT-LHWall switch sensors

currentlighting.com © 2022 HLI Solutions, Inc. All rights reserved. Information and specifications subject to change without notice. All values are design or typical values when measured under laboratory conditions. Page 1 of 3 IMPORTANT SAFEGUARDS READ AND FOLLOW ALL SAFETY INSTRUCTIONS Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes: 1. l’appareil ne doit pas produire de brouillage; 2. l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement. SAVE THESE INSTRUCTIONS AND PROVIDE TO OWNER AFTER INSTALLATION IS COMPLETED 1.YH9NXSMDT-LH IC: 9044A-NXSMDTLH 1.This device complies with FCC part 15 Rules. Operation is subject to the following two conditions: This device may not cause harmful inference. 2.This device must accept any interference received, including interference that may cause undesired operation. 2. FCC Interference Statement (Part 15.105(b)): This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: 1.Reorient or relocate the receiving antenna. 2.Increase the separation between the equipment and receiver 3.Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. 4.Consult the dealer or an experienced radio/TV technician for help. 3. FCC Part 15 Clause 15.21: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. 4. ISED RSS-Gen Notice This device complies with Industry Canada’s license-exempt RSSs. Operation is subject to the following two conditions: 1.The device may not cause interference; and 2.This device must accept any interference, including interference that may cause undesired operation of the device. 93166047 Rev. A NXSMDT/NXSMIR-LH Series Sensors Wall Switch Sensors NX LightHAWK INSTALLATION INSTRUCTIONS (Rev 09/01/22) NXSMDT /NXSMIR-LH-Install-Sheet PRECAUTIONS Read and understand all instructions before beginning installation. CAUTION: FOR USE WITH CLASS 2, LOW VOLTAGE SYSTEMS ONLY. DO NOT USE IN HIGH VOLTAGE APPLICATIONS. NOTICE: Class 2 Device, 12V - 24V, 40mA NOTICE: For installation by a licensed electrician in accordance with National and/or Local Electrical Codes and the following instructions. Confirm device ratings are suitable for application prior to installation. Use of this device in applications beyond its specified ratings other than its intended use may cause an unsafe condition and will void manufacturer’s warranty. Use only approved materials and components (i.e. wire nuts, electrical box, etc.) as appropriate for installation. NOTICE: DO NOT INSTALL IF PRODUCT APPEARS TO BE DAMAGED. NOTICE: Do not use outdoors. For In-fixture use only. NOTICE: Do not use this equipment for other than its intended use. NOTICE: Line voltage wiring is not permitted in the electrical wall-box where this device is installed REG ULATORY INFORMATION currentlighting.com © 2022 HLI Solutions, Inc. All rights reserved. Information and specifications subject to change without notice. All values are design or typical values when measured under laboratory conditions. CONSTRUCTION MOUNTING OPERATING ENVIRONMENT •Rated for Indoor Use Only •Operating temperature: 32° to 104°F (0° to 40°C) •Relative humidity (non-condensing) 0% to 95% WIRELESS SENSORS PROGRAMMING INTERFACE •NX Lighting Controls Mobile App •NX Area Controller (NXAC) for Network Applications CERTIFICATIONS WARRANTY •5-year limited warranty •See HCS Standard Warranty for additional information ELECTRICAL Input: •Housing: Rugged injection molded plastic, Polylac FR-ABS, (UL-94 5VA) flame class rating •Color: White, Black, Gray (MTS); Ivory, Light Almond, Red (MTO) •2.4oz (68g) •Dimensions: 4.12” (104.65mm) H x 1.86” (47.24mm) x 1.86"(47.24mm) D •Input Voltage: 12 - 24VDC supplied by NXRCFX2 (NX Room Controller) •Power Consumption: 40mA •Wiring: Uses NXV •Single-gang NEMA-style switch box (standard switch box - max mounting height: 48") •Decorator-style wall plate sold separately (304.8 square meters) •LED Indicator (Red) indicates infrared motion •LED Indicator (Green) indicates ultrasonic motion •cULus Listed •Complies with FCC Part 15.247 •FCC ID: YH9NXSMDT-LH •IC: 9044A-NXSMDTLH DESCRIPTION NXSMDT/NXSMIR-LH Digital Smart Sensor is a combination Passive Infrared and Ultrasonic Occupancy Sensor with Closed Loop Daylight Harvesting specifically designed for wall switch applications. When used with corresponding NXRCFX2 Series Room Controller, the NXSMDT/NXSMIR-LH Digital Sensor can be programmed to provide Automatic On/Off control based on occupancy or Manual On/ Automatic off control for vacancy applications as well as Automatic Light Level Control based on the amount of ambient daylight. When used with corresponding NXRCFX2 Series Room Controller, the NXSMDT/NXSMIR-LH Digital Sensor can also be programmed with the button functionality of our NXSWR Wall Stations. The NXSMDT/NXSMIR-LH Digital Sensor also includes an Integral Bluetooth® for programming from a mobile device. The NXSMDT/NXSMIR-LH Digital Sensor can be configured via the NX Lighting Controls mobile application a…

Text truncated - open the document above for the full version.

NXSMDT-LH0-BK NXSMDT-LH0-RD NXSMDT-LH0-LA NXSMDT-LH0-GY NXSMDT-LH0-IV NXSMDT-LH0-WH NXSMDT-LH with no switch NXSMDT-LH1-BK NXSMDT-LH1-RD NXSMDT-LH1-LA NXSMDT-LH1-GY NXSMDT-LH1-IV NXSMDT-LH1-WH NXSMDT-LH with one switch NXSMDT-LH2-BK NXSMDT-LH2-RD NXSMDT-LH2-LA NXSMDT-LH2-GY NXSMDT-LH2-IV NXSMDT-LH2-WH NXSMDT-LH with two switch

NXSMIR-LH0-BK NXSMIR-LH0-RD NXSMIR-LH0-LA NXSMIR-LH0-GY NXSMIR-LH0-IV NXSMIR-LH0-WH NXSMIR-LH with no switch NXSMIR-LH1-BK NXSMIR-LH1-RD NXSMIR-LH1-LA NXSMIR-LH1-GY NXSMIR-LH1-IV NXSMIR-LH1-WH NXSMIR-LH with one switch NXSMIR-LH2-BK NXSMIR-LH2-RD NXSMIR-LH2-LA NXSMIR-LH2-GY NXSMIR-LH2-IV NXSMIR-LH2-WH NXSMIR with two switch

NXSMDT-LH0-BK NX Digital Smart Occupancy Sensor, Wall Switch, 0 Button, PIR/US, Black 12-24 Vdc, 40 mA, Class 2 FCC ID: YH9NXSMDT-LH IC: 9044A-NXSMDTLH E174097 Assembled in FW: HW: China XXXX NXSMDT-LH0-GY NX Digital Smart Occupancy Sensor, Wall Switch, 0 Button, PIR/US, Gray 12-24 Vdc, 40 mA, Class 2 FCC ID: YH9NXSMDT-LH IC: 9044A-NXSMDTLH E174097 Assembled in FW: HW: China XXXX NXSMDT-LH0-IV NX Digital Smart Occupancy Sensor, Wall Switch, 0 Button, PIR/US, Ivory 12-24 Vdc, 40 mA, Class 2 FCC ID: YH9NXSMDT-LH IC: 9044A-NXSMDTLH E174097 Assembled in FW: HW: China XXXX NXSMDT-LH0-LA NX Digital Smart Occupancy Sensor, Wall Switch, 0 Button, PIR/US, Lt. Alm. 12-24 Vdc, 40 mA, Class 2 FCC ID: YH9NXSMDT-LH IC: 9044A-NXSMDTLH E174097 Assembled in FW: HW: China XXXX NXSMDT-LH0-RD NX Digital Smart Occupancy Sensor, Wall Switch, 0 Button, PIR/US, Red 12-24 Vdc, 40 mA, Class 2 FCC ID: YH9NXSMDT-LH IC: 9044A-NXSMDTLH E174097 Assembled in FW: HW: China XXXX NXSMDT-LH0-WH NX Digital Smart Occupancy Sensor, Wall Switch, 0 Button, PIR/US, White 12-24 Vdc, 40 mA, Class 2 FCC ID: YH9NXSMDT-LH IC: 9044A-NXSMDTLH E174097 Assembled in FW: HW: China XXXX NXSMDT-LH1-BK NX Digital Smart Occupancy Sensor, Wall Switch, 1 Button, PIR/US, Black 12-24 Vdc, 40 mA, Class 2 FCC ID: YH9NXSMDT-LH IC: 9044A-NXSMDTLH E174097 Assembled in FW: HW: China XXXX NXSMDT-LH1-GY NX Digital Smart Occupancy Sensor, Wall Switch, 1 Button, PIR/US, Gray 12-24 Vdc, 40 mA, Class 2 FCC ID: YH9NXSMDT-LH IC: 9044A-NXSMDTLH E174097 Assembled in FW: HW: China XXXX NXSMDT-LH1-IV NX Digital Smart Occupancy Sensor, Wall Switch, 1 Button, PIR/US, Ivory 12-24 Vdc, 40 mA, Class 2 FCC ID: YH9NXSMDT-LH IC: 9044A-NXSMDTLH E174097 Assembled in FW: HW: China XXXX NXSMDT-LH1-LA NX Digital Smart Occupancy Sensor, Wall Switch, 1 Button, PIR/US, Lt. Alm. 12-24 Vdc, 40 mA, Class 2 FCC ID: YH9NXSMDT-LH IC: 9044A-NXSMDTLH E174097 Assembled in FW: HW: China XXXX NXSMDT-LH1-RD NX Digital Smart Occupancy Sensor, Wall Switch, 1 Button, PIR/US, Red 12-24 Vdc, 40 mA, Class 2 FCC ID: YH9NXSMDT-LH IC: 9044A-NXSMDTLH E174097 Assembled in FW: HW: China XXXX NXSMDT-LH1-WH NX Digital Smart Occupancy Sensor, Wall Switch, 1 Button, PIR/US, White 12-24 Vdc, 40 mA, Class 2 FCC ID: YH9NXSMDT-LH IC: 9044A-NXSMDTLH E174097 Assembled in FW: HW: China XXXX NXSMDT-LH2-BK NX Digital Smart Occupancy Sensor, Wall Switch, 2 Button, PIR/US, Black 12-24 Vdc, 40 mA, Class 2 FCC ID: YH9NXSMDT-LH IC: 9044A-NXSMDTLH E174097 Assembled in FW: HW: China XXXX NXSMDT-LH2-GR NX Digital Smart Occupancy Sensor, Wall Switch, 2 Button, PIR/US, Gray 12-24 Vdc, 40 mA, Class 2 FCC ID: YH9NXSMDT-LH IC: 9044A-NXSMDTLH E174097 Assembled in FW: HW: China XXXX NXSMDT-LH2-IV NX Digital Smart Occupancy Sensor, Wall Switch, 2 Button, PIR/US, Ivory 12-24 Vdc, 40 mA, Class 2 FCC ID: YH9NXSMDT-LH IC: 9044A-NXSMDTLH E174097 Assembled in FW: HW: China XXXX NXSMDT-LH2-LA NX Digital Smart Occupancy Sensor, Wall Switch, 2 Button, PIR/US, Lt. Alm. 12-24 Vdc, 40 mA, Class 2 FCC ID: YH9NXSMDT-LH IC: 9044A-NXSMDTLH E174097 Assembled in FW: HW: China XXXX NXSMIR-LH0-GY NX Digital Smart Occupancy Sensor, Wall Switch, 0 Button, PIR, Gray 12-24 Vdc, 40 mA, Class 2 FCC ID: YH9NXSMDT-LH IC: 9044A-NXSMDTLH E174097 Assembled in FW: HW: China XXXX NXSMDT-LH2-WH NX Digital Smart Occupancy Sensor, Wall Switch, 2 Button, PIR/US, White 12-24 Vdc, 40 mA, Class 2 FCC ID: YH9NXSMDT-LH IC: 9044A-NXSMDTLH E174097 Assembled in FW: HW: China XXXX NXSMIR-LH0-BK NX Digital Smart Occupancy Sensor, Wall Switch, 0 Button, PIR, Black 12-24 Vdc, 40 mA, Class 2 FCC ID: YH9NXSMDT-LH IC: 9044A-NXSMDTLH E174097 Assembled in FW: HW: China XXXX NXSMIR-LH0-GY NX Digital Smart Occupancy Sensor, Wall Switch, 0 Button, PIR, Gray 12-24 Vdc, 40 mA, Class 2 FCC ID: YH9NXSMDT-LH IC: 9044A-NXSMDTLH E174097 Assembled in FW: HW: China XXXX NXSMIR-LH0-IV NX Digital Smart Occupancy Sensor, Wall Switch, 0 Button, PIR, Ivory 12-24 Vdc, 40 mA, Class 2 FCC ID: YH9NXSMDT-LH IC: 9044A-NXSMDTLH E174097 Assembled in FW: HW: China XXXX NXSMIR-LH0-LA NX Digital Smart Occupancy Sensor, Wall Switch, 0 Button, PIR, Lt. Alm. 12-24 Vdc, 40 mA, Class 2 FCC ID: YH9NXSMDT-LH IC: 9044A-NXSMDTLH E174097 Assembled in FW: HW: China XXXX NXSMIR-LH0-RD NX Digital Smart Occupancy Sensor, Wall Switch, 0 Button, PIR, Red 12-24 Vdc, 40 mA, Class 2 FCC ID: YH9NXSMDT-LH IC: 9044A-NXSMDTLH E174097 Assembled in FW: HW: China XXXX NXSMIR-LH0-WH NX Digital Smart Occupancy Sensor, Wall Switch, 0 Button, PIR, White 12-24 Vdc, 40 mA, Class 2 FCC ID: YH9NXSMDT-LH IC: 9044A-NXSMDTLH E174097 Assembled in FW: HW: China XXXX NXSMIR-LH1-BK NX Digital Smart Occupancy Sensor, Wall Switch, 1 Button, PIR, Black 12-24 Vdc, 40 mA, Class 2 FCC ID: YH9NXSMDT-LH IC: 9044A-NXSMDTLH E174097 Assembled in FW: HW: China XXXX NXSMIR-LH1-GY NX Digital Smart Occupancy Sensor, Wall Switch, 1 Button, PIR, Gray 12-24 Vdc, 40 mA, Class 2 FCC ID: YH9NXSMDT-LH IC: 9044A-NXSMDTLH E174097 Assembled in FW: HW: China XXXX NXSMIR-LH1-IV NX Digital Smart Occupancy Sensor, Wall Switch, 1 Button, PIR, Ivory 12-24 Vdc, 40 mA, Class 2 FCC ID: YH9NXSMDT-LH IC: 9044A-NXSMDTLH E174097 Assembled in FW: HW: China XXXX NXSMIR-LH1-LA NX Digital Smart Occupancy Sensor, Wall Switch, 1 Button, PIR, Lt. Alm. 12-24 Vdc, 40 mA, Class 2 FCC ID: YH9NXSMDT-LH IC: 9044A-NXSMDTLH E174097 Assembled in FW: HW: China XXXX NXSMIR-LH1-RD NX Digital Smart Occupancy Sensor, Wall Switch, 1 Button, PIR, Red 12-24 Vdc, 40 mA, Class 2 FCC ID: YH9NXSMDT-LH IC: 9044A-NXSMDTLH E174097 Assembled in FW: HW: China XXXX NXSMIR-LH1-WH NX Digital Smart Occupancy Sensor, Wall Switch, 1 Button, PIR, White 12-24 Vdc, 40 mA, Class 2 FCC ID: YH9NXSMDT-LH IC: 9044A-NXSMDTLH E174097 Assembled in FW: HW: China XXXX NXSMIR-LH2-BK NX Digital Smart Occupancy Sensor, Wall Switch, 2 Button, PIR, Black 12-24 Vdc, 40 mA, Class 2 FCC ID: YH9NXSMDT-LH IC: 9044A-NXSMDTLH E174097 Assembled in FW: HW: China XXXX NXSMIR-LH2-GY NX Digital Smart Occupancy Sensor, Wall Switch, 2 Button, PIR, Gray 12-24 V…

Text truncated - open the document above for the full version.

Project #: 23494-15 Company: Hubbell Control Solutions EUT: NXSMDT-LH and NXSMIR-LH RF Exposure Evaluation Report Prepared for: Hubbell Control Solutions 710 Hesters Crossing Rd., Suite 100 Round Rock, TX 78681 By Nemko USA, Inc. 1601 North A.W. Grimes Blvd., Suite B Round Rock, Texas 78665 January 20, 2023 Written by Shakil Murad Wireless Engineer 23494-15, NXSMDT-LH and NXSMIR-LH Nemko USA, Inc. Page 2 of 6 Table of Contents 1.0 Maximum Permissible Exposure Evaluation (Supplements the test report.) ....................................................... 3 1.1 Applicable Documents .................................................................................................................................... 3 1.2 Criteria ............................................................................................................................................................ 3 1.3 Duty Cycle Correction Factor Measurement .................................................................................................. 4 1.4 Power to Exposure Calculation, Conducted .................................................................................................... 5 1.5 RF MPE Evaluation – FCC ............................................................................................................................. 5 1.6 RF MPE Evaluation – ISED Canada............................................................................................................... 6 1.7 Conclusion ...................................................................................................................................................... 6 NOTICE: (1) This Report must not be used to claim product endorsement by ANAB, NIST, the FCC or any other Agency. This report also does not warrant certification by ANAB or NIST. (2) This report shall not be reproduced except in full, without the written approval of Nemko USA, Inc. (3) The significance of this report is dependent on the representative character of the test sample submitted for evaluation and the results apply only in reference to the sample tested. The manufacturer must continuously implement the changes shown herein to attain and maintain the required degree of compliance. 23494-15, NXSMDT-LH and NXSMIR-LH Nemko USA, Inc. Page 3 of 6 1.0 Maximum Permissible Exposure Evaluation (Supplements the test report.) The measured power is considered for the intended use of the device and resulting RF exposure to the user. This report is representative of the following family model variants, and represents worst case RF exposure: NXSMDT-LH0- WH NXSMIR-LH0- WH NXSMDT-LH1-WH NXSMIR-LH1-WH NXSMDT-LH2-WH NXSMIR-LH2-WH NXSMDT-LH0-BK NXSMIR-LH0-BK NXSMDT-LH1- BK NXSMIR-LH1- BK NXSMDT-LH2-BK NXSMIR-LH2-BK NXSMDT-LH0-GY NXSMIR-LH0-GY NXSMDT-LH1-GY NXSMIR-LH1-GY NXSMDT-LH2-GY NXSMIR-LH2-GY NXSMDT-LH0-RD NXSMIR-LH0-RD NXSMDT-LH1-RD NXSMIR-LH1-RD NXSMDT-LH2-RD NXSMIR-LH2-RD NXSMDT-LH0-LA NXSMIR-LH0-LA NXSMDT-LH1-LA NXSMIR-LH1-LA NXSMDT-LH2-LA NXSMIR-LH2-LA NXSMDT-LH0-IV NXSMIR-LH0-IV NXSMDT-LH1-IV NXSMIR-LH1-IV NXSMDT-LH2-IV NXSMIR-LH2-IV 1.1 Applicable Documents Document Title RSS-102 Issue 5 Radio Frequency (RF) Exposure Compliance of Radiocommunication Apparatus (All Frequency Bands) KDB 447498 D01 General RF Exposure Guidance v06 RF EXPOSURE PROCEDURES AND EQUIPMENT AUTHORIZATION POLICIES FOR MOBILE AND PORTABLE DEVICES OET Bulletin 65 Edition 97-01 Evaluating Compliance with FCC Guidelines for Human Exposure to Radiofrequency Electromagnetic Fields 1.2 Criteria Section Reference Test Detail FCC 47 CFR Part 1 I, 1.1310 // RSS-102, Issue 5 Radiofrequency radiation exposure limits 23494-15, NXSMDT-LH and NXSMIR-LH Nemko USA, Inc. Page 4 of 6 1.3 Duty Cycle Correction Factor Measurement Measurement is based on intervals not to exceed 100 msec. Maximum transmitter on time is divided by the lesser of 100 msec or the actual measured minimum transmitter interval time. The result is converted to dB and applied as needed to peak measurements of transmitter artifacts to determine average power. This is not a pass/fail measurement. Continuous packet transmission mode was used for the duty cycle measurement, which would represent a worst- case operating scenario. On Time (msec) Time Interval (msec) Duty Cycle (On Time/Interval) Exposure Weighing Factor (dB) (10 * Log 10 (Duty Cycle) 1.253 1.485 = 0.84 = -0.74 Plotted measurements appear below: Transmit Event TimeTime Interval (Return to channel time) 23494-15, NXSMDT-LH and NXSMIR-LH Nemko USA, Inc. Page 5 of 6 1.4 Power to Exposure Calculation, Conducted The EUT transmitter power is determined by conducted measurement. Safe exposure distance was calculated for the allowed maximum uncontrolled public exposure limit. Measured Conducted Peak Power (dBm) Exposure Weighing Factor (dB) Antenna Gain (dBi) Corrected Peak Power EIRP (dBm) EIRP In Linear Terms (mW) 7.21 Not used to get worse case EIRP 1.5 8.71 5.26 1.5 RF MPE Evaluation – FCC FCC 47 CFR Part 1 I, 1.1310, Radiofrequency radiation exposure limits. According to table above, the MPE limit for 2400 MHz transmitter shall not exceed power density of 1 mW/cm 2 at a distance of 20 cm from the EUT. Calculation: EIRP = 5.26 mW = 0.00526 W Distance = d = 20 cm = 0.2 m Power Density = EIRP/4πd 2 = 0.00526/4*π*(0.2) 2 = 0.0105 W/m 2 = 0.00105 mW/cm 2 Power Density 0.00105 mW/cm 2 < 1 mW/cm 2 23494-15, NXSMDT-LH and NXSMIR-LH Nemko USA, Inc. Page 6 of 6 1.6 RF MPE Evaluation – ISED Canada RSS-102, Section 2.5.2, Exemption Limits for Routine Evaluation – RF Exposure Evaluation RF exposure evaluation is required if the separation distance between the user and/or bystander and the device’s radiating element is greater than 20 cm, except when the device operates as follows: 1) below 20 MHz 6 and the source-based, time-averaged maximum e.i.r.p. of the device is equal to or less than 1 W (adjusted for tune-up tolerance) 2) at or above 20 MHz and below 48 MHz and the source-based, t…

Text truncated - open the document above for the full version.

W3001 Datasheet version 1.0. 2.4 GHz WiFi Antenna. (04/08). © 2008. All Rights Reserved. 2.4 GHz WiFi Antenna 10 x 3.2 x 4.0 mm Ceramic Chip Antenna (On Ground type, Top surface ground removal area 10.80 x 6.25 mm). Pulse Part Number: W3001 Pulse Finland Oy Takatie 6 90440 Kempele, Finland Tel: +358 207 935 500 Fax: +358 207 935 501 www.pulseeng.com/antennas Features - Omni directional radiation (Azimuthal plane) - Low profile - Compact size W x L x H (10 x 3.2 x 4 mm) - Low weight (600 mg) - Lead free materials - Fully SMD compatible - Lead free soldering compatible - Tape and reel packing - RoHS compliant product Applications - Bluetooth - 2.4 GHz WLAN - 2.4 GHz ISM Band System Electrical specifications @ +25 °C Note: Electrical characteristics depend on test board (GP) size and antenna positioning on GP and Ground Clearance area size. WiFi 2.4 GHz Typical performance (Test board size 80 x 37 mm, PWB top surface ground removal area 10.80 x 6.25 mm, position 1 on PWB) Frequency Range [MHz] Max Gain [dBi] Efficiency [%] / [dB] Return loss min. [dB] Impedance [Ω] Operating Temperature [° C] 2400 – 2483.51.5 (Peak) 0.5 (Band edges) 75 /-1.25 (Peak) 60/-2.25 (Band edges) -650-45 to +85 W3001 Datasheet version 1.0. 2.4 GHz WiFi Antenna. (04/08). © 2008. All Rights Reserved. 2.4 GHz WiFi Antenna 10 x 3.2 x 4.0 mm Ceramic Chip Antenna (On Ground type, Top surface ground removal area 10.80 x 6.25 mm). Pulse Part Number: W3001 Pulse Finland Oy Takatie 6 90440 Kempele, Finland Tel: +358 207 935 500 Fax: +358 207 935 501 www.pulseeng.com/antennas Terminal Configuration and Dimensions On Ground type, Top surface ground removal area 10.80 x 6.25 mm Matching and tuning component values depend on application and surrounding mechanics / materials. Feed line should be designed to match 50 Ω characteristic impedance, depending on PWB material and thickness. Recommended test board layout for electrical characteristic measurement, test board outline size 80 x 37 mm. Antenna PWB Layout Specifications On Ground type, Top surface ground removal area 10.80 x 6.25 mm PWB layout for W3001 Antenna Note: All dimensions are in metric system. Antenna features No. 1 2 Terminal name Feed / GND Feed / GND Terminal Dimensions 1.5 x 2.75 mm 1.5 x 2.75 mm Antenna is symmetrical. Either of terminals 1 or 2 can be feed / GND CWjY^_d]9ecfed[djefj_edWbi^kdj <[[ZYedjWYj 789:<=> ; =hekdZYedjWYj =hekdZWh[W =hekdZl_W^eb[ =hekdZWh[Wi^ekbZX[ikhhekdZ[Zm_j^=hekdZ l_W^eb[i <[[Zb_d[+&E^c 7do jo f[e\+&E^c\[[Zb_d[YWdX[ki[Z$?dd[h bWo [hied\[[Zb_d[Wh[Wd[[ZjeZ[i_]d[Zje]_l[ +&E^cY^WhWYj[h_ij_Yije\[[Zb_d[$ '$+& ¦&$(& ($-+ ¦&$'& &$(& ¦&$(& '&$&& ¦&$'& 7] c[jWbb_pWj_ed YedjWYjfWZ Wh[W(n '( '$+& ¦&$(& ($-+ ¦&$'& &$(& ¦&$(& *$&& ¦&$'& )$'+ ¦&$&+ &$(& ¦&$(& '&$&& ¦&$'& 7] c[jWbb_pWj_ed YedjWYjfWZ Wh[W(n 7] c[jWbb_pWj_ed 7bbjkd_d]Wh[W Z_c[di_edilWho$ C[jWbb_pWj_edh[cel[Z"j^[h[ c_]^jX[l_ikWbY^Wd][iedj^_ii_Z[ 7] c[jWbb_pWj_ed7] c[jWbb_pWj_ed CWjY^_d]9ecfed[djefj_edWbi^kdj <[[ZYedjWYj 789:<=> ; =hekdZYedjWYj =hekdZWh[W =hekdZl_W^eb[ =hekdZWh[Wi^ekbZX[ikhhekdZ[Zm_j^=hekdZ l_W^eb[i <[[Zb_d[+&E^c 7do jo f[e\+&E^c\[[Zb_d[YWdX[ki[Z$?dd[h bWo [hied\[[Zb_d[Wh[Wd[[ZjeZ[i_]d[Zje]_l[ +&E^cY^WhWYj[h_ij_Yije\[[Zb_d[$ '$+& ¦&$(& ($-+ ¦&$'& &$(& ¦&$(& '&$&& ¦&$'& 7] c[jWbb_pWj_ed YedjWYjfWZ Wh[W(n '( '$+& ¦&$(& ($-+ ¦&$'& &$(& ¦&$(& *$&& ¦&$'& )$'+ ¦&$&+ &$(& ¦&$(& '&$&& ¦&$'& 7] c[jWbb_pWj_ed YedjWYjfWZ Wh[W(n 7] c[jWbb_pWj_ed 7bbjkd_d]Wh[W Z_c[di_edilWho$ C[jWbb_pWj_edh[cel[Z"j^[h[ c_]^jX[l_ikWbY^Wd][iedj^_ii_Z[ 7] c[jWbb_pWj_ed7] c[jWbb_pWj_ed W3001 Datasheet version 1.0. 2.4 GHz WiFi Antenna. (04/08). © 2008. All Rights Reserved. 2.4 GHz WiFi Antenna 10 x 3.2 x 4.0 mm Ceramic Chip Antenna (On Ground type, Top surface ground removal area 10.80 x 6.25 mm). Pulse Part Number: W3001 Pulse Finland Oy Takatie 6 90440 Kempele, Finland Tel: +358 207 935 500 Fax: +358 207 935 501 www.pulseeng.com/antennas Metallization layers for W3001 Antenna PWB pad dimensions and antenna position for W3001 Antenna W3001 Datasheet version 1.0. 2.4 GHz WiFi Antenna. (04/08). © 2008. All Rights Reserved. 2.4 GHz WiFi Antenna 10 x 3.2 x 4.0 mm Ceramic Chip Antenna (On Ground type, Top surface ground removal area 10.80 x 6.25 mm). Pulse Part Number: W3001 Pulse Finland Oy Takatie 6 90440 Kempele, Finland Tel: +358 207 935 500 Fax: +358 207 935 501 www.pulseeng.com/antennas Typical ground via hole placement in PWB layout for W3001 Antenna Solder resist opening and Paste stencil recommendation for W3001 Antenna W3001 Datasheet version 1.0. 2.4 GHz WiFi Antenna. (04/08). © 2008. All Rights Reserved. 2.4 GHz WiFi Antenna 10 x 3.2 x 4.0 mm Ceramic Chip Antenna (On Ground type, Top surface ground removal area 10.80 x 6.25 mm). Pulse Part Number: W3001 Pulse Finland Oy Takatie 6 90440 Kempele, Finland Tel: +358 207 935 500 Fax: +358 207 935 501 www.pulseeng.com/antennas Recommended antenna position on PWB for W3001 Antenna Our test PWB size is 37 x 80 mm, other sized boards can be used depending on customer device size (minimum 35 x 35 mm). Position 1 Tested Position 2 (Optional, minimum dis- tance from top corner is 10 mm) Position 3 (Optional, minimum distance from corner is 10 mm) W3001 Datasheet version 1.0. 2.4 GHz WiFi Antenna. (04/08). © 2008. All Rights Reserved. 2.4 GHz WiFi Antenna 10 x 3.2 x 4.0 mm Ceramic Chip Antenna (On Ground type, Top surface ground removal area 10.80 x 6.25 mm). Pulse Part Number: W3001 Pulse Finland Oy Takatie 6 90440 Kempele, Finland Tel: +358 207 935 500 Fax: +358 207 935 501 www.pulseeng.com/antennas Typical Electrical Characteristics (T=25 °C) Measured on the 80 x 37 mm test board with matching circuit (1.2 pF shunt matching capacitor on feed). Mea- sured in antenna position 1 on PWB layout, see previous page. 9;DJ;H**&$&&&&&&C>pIF7D.&&$&&&&&&C>p FHc :[b 9eh &&;ZW'%%-&&/),/(+ '#)<=oL^;^ 9>'I'…

Text truncated - open the document above for the full version.

Project #: 23494-15 Company: Hubbell Control Solutions EUT Model(s): NXSMDT-LH and NXSMIR-LH FCC and Industry Canada Wireless Test Report Prepared for: Hubbell Control Solutions 710 Hesters Crossing Rd, Suite 100 Round Rock, TX 78681 By Nemko USA, Inc. 1601 North A.W. Grimes Blvd., Suite B Round Rock, Texas 78665 January 25, 2023 Written by Shakil Murad Wireless Engineer 23494-15, NXSMDT-LH and NXSMIR-LH 22738 Nemko USA, Inc. Page 2 of 40 Table of C ontents Test Result Summary .................................................................................................................................................... 5 1.0 Introduction .......................................................................................................................................................... 6 1.1 Scope ............................................................................................................................................................... 6 1.2 EUT Description ............................................................................................................................................. 6 1.3 EUT Test Mode ............................................................................................................................................... 6 1.4 EUT Test Configuration .................................................................................................................................. 6 1.5 Modifications to Equipment ............................................................................................................................ 7 1.6 Test Site .......................................................................................................................................................... 7 1.7 Measurement Corrections ............................................................................................................................... 7 1.8 Applicable Documents .................................................................................................................................... 7 2.0 Fundamental Power ............................................................................................................................................. 8 2.1 Test Procedure ................................................................................................................................................ 8 2.2 Test Criteria .................................................................................................................................................... 8 2.3 Test Results, Peak Power – Model: NXSMDT-LH-X ......................................................................................... 8 3.0 Occupied Bandwidth .......................................................................................................................................... 10 3.1 Test Procedure .............................................................................................................................................. 10 3.2 Test Criteria .................................................................................................................................................. 10 3.3 Test Results, Occupied Bandwidth – Model: NXSMDT-LH-X ........................................................................ 10 4.0 Duty Cycle ......................................................................................................................................................... 12 4.1 Test Results, Duty Cycle – Model: NXSMDT-LH-X ....................................................................................... 12 5.0 Power Spectral Density ...................................................................................................................................... 13 5.1 Test Procedure .............................................................................................................................................. 13 5.2 Test Criteria .................................................................................................................................................. 13 5.3 Test Results, Power Spectral Density – Model: NXSMDT-LH-X .................................................................... 13 6.0 Band Edge .......................................................................................................................................................... 15 6.1 Test Procedure .............................................................................................................................................. 15 6.2 Test Criteria .................................................................................................................................................. 15 6.3 Test Results ................................................................................................................................................... 15 6.3.1 Test data – Model: NXSMDT-LH-X ....................................................................................................... 16 7.0 Conducted Antenna Port Spurious Emissions, Transmit Mode ......................................................................... 17 7.1 Test Procedure .......................................…

Text truncated - open the document above for the full version.