YI4DW25UX40Microwave Oven

MICROWAVE OVEN I NSTRUCTION MANUAL MODEL：25UX40 Please read this booklet carefully before fixing and using, and save it for future reference. Zhongshan Donlim Weili Electrical Appliances Co., Ltd ADDRESS: Fusha Industrial Park, Fusha Town, Zhongshan City, Guangdong Province 1 IMPORTANT SAFEGUARDS The following basic precautions should always be followed when using electrical appliance: WARNING – To reduce the risk of burn, electric shock, fire, injury to persons, or exposure to excessive microwave energy: 1. Read all instructions before using. 2. Read and follow the specific PRECAUTIONS TO AVOID POSSIBLE EXPOSURE TO EXCESSIVE MICROWAVE ENERGY found on next page. 3. This appliance must be grounded. Connect only to properly grounded outlet. See GROUNDING INSTRUCTIONS found on next page. 4. Install or locate this appliance only in accordance with the provided installation instructions. 5. Some products such as whole eggs and sealed containers - for example, closed glass jars - may explode and should not be heated in this oven. 6. Use this appliance only for its intended use as described in the manual. Do not use corrosive chemicals or vapors in this appliance. This type of oven is specifically designed to heat, cook, or dry food. It is not designed for industrial or laboratory use. 7. As with any appliance, close supervision is necessary when used by children. 8. Do not operate this appliance if it has a damaged cord or plug, if it is not working properly, or if has damaged or dropped. 9. This appliance should be serviced only by qualified service personnel. Contact nearest authorized service facility for examination, repair, or a adjustment. 10. Do not cover or block any openings on the appliance. 11. Do not stall this appliance outdoors. Do not use this product near water - for example, near a kitchen sink, in a wet basement, or near a swimming pool, and the like. 12. Do not immerse cord or plug in water. 13. Keep cord away from heated surface. 14. Do not clean with metal scouring pads. Pieces can burn off the pad and touch electrical parts involving a risk of electric shock. 15. Do not operate the oven without any liquid or food inside the oven. This would do damage the oven. 16. Make sure the utensils do not touch the interior walls during cooking. 17. Do not let cord hang over edge of table or counter. 18. Attention must be taken when cleaning door surface. See details on Cleaning and Maintenance. 19. To reduce the risk of fire in the oven cavity: i) Do not overcook food. Carefully attend appliance if paper, plastic, or other combustible materials are placed inside the oven to facilitate cooking. ii) Remove wire twist-ties from paper or plastic bags before placing bag in oven. iii) If materials inside the oven should ignite, keep oven door closed, turn oven off, and disconnect the power cord, or shut off at the fuse or circuit breaker panel. iv) Do not use the cavity for storage purposes. Do not leave paper products, cooking utensils, or food in the cavity when not in use. 20.Liquids, such as water, coffee, or tea are able to be overheated beyond the boiling point without appearing to be boiling. Visible bubbling or boiling when the container is removed from the microwave oven is not always present. THIS COULD RESULT IN VERY HOT LIQUIDS SUDDENLY BOILING OVER WHEN THE CONTAINER IS DISTURBED OR A SPOON OR OTHER UTENSIL IS INSERTED INTO THE LIQUID. To reduce the risk of injury to persons: (a) Do not overheat the liquid. (b) Stir the liquid both before and halfway through heating it. (c) Do not use straight-sided containers with narrow necks. 2 (d) After heating, allow the container to stand in the microwave oven for a short time before removing the container. (e) Use extreme care when inserting a spoon or other utensil into the container. SAVE THESE INSTRUCTIONS HOUSEHOLD USE ONLY CAUTION: MICROWAVE RADIATION PRECAUTIONS TO AVOID POSSIBLE EXPOSURE TO EXCESSIVE MICROWAVE ENERGY (a) Do not operate or allow the oven to be operated with the door open. (b) Make the following safety checks on all ovens to be serviced before activating the magnetron or other microwave source, and make repairs as necessary: (1) interlock operation, (2) proper door closing, (3) seal and sealing surfaces (arcing, wear, and other damage), (4) damage to or loosening of hinges and latches, (5) evidence of dropping or abuse. (c) Before turning on microwave power for any service test or inspection within the microwave generating compartments, check the magnetron, wave guide or transmission line, and cavity for proper alignment, integrity, and connection. (d) Any defective or misadjusted components in the interlock, monitor, door seal, and microwave generation and transmission systems shall be repaired, replaced, or adjusted by procedures described in this manual before the oven is released to the owner. (e) A microwave leakage check to verify compliance with the Federal Performance Standard should be performed on each oven prior to release to the owner. WARNING: To reduce the risk of fire or electric shock, the oven must be placed on a counter top which is a minimum of 36 inches from the floor, do not install closer than 2 inches on the sides wall, top and at the rear of the oven for air circulation. GROUNDING INSTRUCTIONS This appliance must be grounded. In the event of an electrical short circuit, grounding reduces the risk of electric shock by providing an escape wire for the electrical current. This appliance is equipped with a cord having a grounding wire with a grounding plug. The plug must be plugged into an outlet that is properly installed and grounded. WARNING - IMPROPER USE OF THE GROUNDING CAN RESULT IN A RISK OF ELECTRIC SHOCK. Consult a qualified electrician or serviceman if the grounding instructions are not completely understood, or it doubt exists as to whether the appliance is properly grounded, and either; 1) If it is necessary to use an extension cord, use only a 3 wire extension cord that has a 3-bl…

Text truncated - open the document above for the full version.

EXHIBIT A - FCC ID LABEL AND LOCATION FCC ID Label FCC ID Label Location Information Label here

EXHIBIT C - EUT INTERNAL PHOTOGRAPHS EUT – Cover off View EUT – Main Board Top View EUT – Main Board Bottom View EUT – Filter Board Top View EUT – Filter Board Bottom View EUT – Power Supply Board Top View EUT – Power Supply Board Bottom View EUT – Magnetron View EUT – Fan Motor View EUT – H.V. Capacitor View EUT – Transformer View EUT –Thermostat View

Note: This test report is prepared for the customer shown above and for the device described herein. It may not be duplicated or used in part without prior written consent from Bay Area Compliance Laboratories Corp. This report must not be used by the customer to claim product certification, approval, or endorsement by NVLAP*, NIST, or any agency of the Federal Government. * This report contains data that are not covered by the NVLAP accreditation and are marked with an asterisk “★” (Rev.2) FCC PART 18 EMI MEASUREMENT AND TEST REPORT For Zhongshan Donlim Weili Electrical Appliances Co., Ltd. Fusha Industrial Park, Fusha Town, Zhongshan, Guangdong, P.R.of China FCC ID: YI4DW25UX40 Report Type: Original Product Type: Microwave Oven Test Engineer: Jack Wang Report No.: RSZ11031652 Report Date: 2011-04-19 Reviewed By: Lisa Zhu EMC Engineer Prepared By: Bay Area Compliance Laboratories Corp. (Shenzhen) 6/F, the 3rd Phase of WanLi Industrial Building, ShiHua Road, FuTian Free Trade Zone Shenzhen, Guangdong,China Tel: +86-755-33320018 Fax: +86-755-33320008 Zhongshan Donlim Weili Electrical Appliances Co., Ltd. FCC ID: YI4DW425UX40 Report #: RSZ11031652 Page 2 of 19 FCC Part 18 Test Report TABLE OF CONTENTS GENERAL INFORMATION.......................................................................................................................................3 PRODUCT DESCRIPTION FOR EQUIPMENT UNDER TEST (EUT) .....................................................................................3 OBJECTIVE...................................................................................................................................................................3 RELATED SUBMITTAL(S)/GRANT(S).............................................................................................................................3 TEST METHODOLOGY..................................................................................................................................................3 TEST FACILITY.............................................................................................................................................................3 OPERATING CONDITION/TEST CONFIGURATION..........................................................................................5 JUSTIFICATION.............................................................................................................................................................5 EQUIPMENT MODIFICATIONS.......................................................................................................................................5 EXTERNAL CABLE LIST AND DETAILS.........................................................................................................................5 CONFIGURATION OF TEST SETUP.................................................................................................................................5 BLOCK DIAGRAM OF TEST SETUP................................................................................................................................5 CONDUCTED EMISSIONS ........................................................................................................................................6 MEASUREMENT UNCERTAINTY....................................................................................................................................6 EUT SETUP..................................................................................................................................................................6 EMI TEST RECEIVER SETUP.........................................................................................................................................7 TEST EQUIPMENT LIST AND DETAILS...........................................................................................................................7 TEST PROCEDURE........................................................................................................................................................7 TEST RESULTS SUMMARY............................................................................................................................................7 TEST DATA..................................................................................................................................................................7 RADIATION HAZARD MEASUREMENT .............................................................................................................10 ENVIRONMENTAL CONDITIONS..................................................................................................................................10 TEST EQUIPMENT LIST AND DETAILS.........................................................................................................................10 RADIATION HAZARD MEASUREMENT........................................................................................................................10 INPUT POWER.............................................................................................................................................................11 LOAD FOR MICROWAVE OVENS.................................................................................................................................11 RF OUTPUT POWER MEASUREMENT..........................................................................................................................11 OPERATING FREQUENCY MEASUREMENT..................................................................................................................12 RADIATED EMISSIONS...........................................................................................................................................16 MEASUREMENT UNCERTAINTY..................................................................................................................................16 EUT SETUP.........................…

Text truncated - open the document above for the full version.

EXHIBIT D - TEST SETUP PHOTOGRAPHS AC Line Conducted Emissions - Front View AC Line Conducted Emissions - Side View Radiated Emissions - Front View (30 MHz-1 GHz) Radiated Emissions - Rear View (30 MHz-1 GHz) Radiated Emissions - Front View (Above 1 GHz) Radiated Emissions - Rear View (Above 1 GHz)