YI4DWB20PAS03Microwave Oven

MICROWAVE OVEN INSTRUCTION MANUAL B20PAS03-A70 IMPORTANT SAFETY INSTRUCTIONS READ CAREFULLY AND KEEP FOR FUTURE REFERENCE 2 Household use only SAVE THESE INSTRUCTIONS .IMPORTANT SAFEGUARDS............。。.................. ... .. When using electrical appliances basic safety precautions should be followed, including the following: WARNING – To reduce the risk of burns, electric shock, fire, injury to persons, or exposure to excessive microwave energy: 1. Read all instructions before using the appliance. 2. Read and follow the specific "PRECAUTIONS TO AVOID POSSIBLE EXPOSURE TO EXCESSIVE MICROWAVE ENERGY" found on page 8. 3. This appliance must be grounded. Connect only to properly grounded outlet. See "GROUNDING INSTRUCTIONS" found on page 9. 4. Install or locate this appliance only in accordance with the provided installation instructions. 5. Some products such as whole eggs and sealed containers – for example, closed glass jars – are able to explode and should not be heated in this oven. 6. Use this appliance only for its intended use as described in the manual. Do not use corrosive chemicals or vapors in this appliance. This type of oven is specifically designed to heat, cook, or dry food. It is not designed for industrial or laboratory use. 7. As with any appliance, close supervision is necessary when used by children. 8. Do not operate this appliance if it has a damaged cord or plug, if it is not working properly, or if it has been damaged or dropped. 9. This appliance should be serviced only by qualified service personnel. Contact nearest authorized service facility for examination, repair, or adjustment. 10. Do not cover or block any openings on the appliance. 11. Do not store this appliance outdoors. Do not use this 3 product near water – for example, near a kitchen sink, in a wet basement, near a swimming pool, or similar locations. 12. Do not immerse cord or plug in water. 13. Keep cord away from heated surfaces. 14. Do not let cord hang over edge of table or counter. 15. When cleaning surfaces of door and oven that comes together on closing the door, use only mild, nonabrasive soaps, or detergents applied with a sponge or soft cloth. 16. To reduce the risk of fire in the oven cavity: a. Do not overcook food. Carefully attend appliance when paper, plastic, or other combustible materials are placed inside the oven to facilitate cooking. b. Remove wire twist-ties from paper or plastic bags before placing bag in oven. c. If materials inside the oven ignite, keep oven door closed, turn oven off, and disconnect the power cord, or shut off power at the fuse or circuit breaker panel. d. Do not use the cavity for storage purposes. Do not leave paper products, cooking utensils, or food in the cavity when not in use. 17. Liquids, such as water, coffee, or tea are able to be overheated beyond the boiling point without appearing to be boiling. Visible bubbling or boiling when the container is removed from the microwave oven is not always present. THIS COULD RESULT IN VERY HOT LIQUIDS SUDDENLY BOILING OVER WHEN THE CONTAINER IS DISTURBED OR A UTENSIL IS INSERTED INTO THE LIQUID. 18. Notice for extension cord: a. A short power-supply cord is provided to reduce the risks resulting from becoming entangled in or tripping over a longer cord. b. Longer cord sets or extension cords are available and may be used if care is exercised in their use. c. If a long cord or extension cord is used: 1) The marked electrical rating of the cord set or extension 4 cord should be at least as great as the electrical rating of the appliance. 2) The extension cord must be a grounding-type 3-wire cord; and 3) The longer cord should be arranged so that it will not drape over the counter top or tabletop where it can be pulled on by children or tripped over unintentionally. The following basic precautions should always be followed when using electrical appliance: 1. Read all instructions before using. 2. Make sure the voltage in your living area corresponding to the one shown on the rating label of the appliance. And the wall socket is properly grounded. 3. TO reduce the risk of fire in the oven cavity: a. DO not overcook the food. b. Remove wire twist -ties from paper or plastic bags before placing bags in the oven. c. Do not heat oil or fat for deep drying as the temperature of oil cannot be controlled. d. After use wipe the waveguide cover with a damp cloth, followed by dry cloth to remove any food splashes and grease. Built -up grease may overheat and begin to cause smoke or catch fire. e. If materials inside the oven should smoke or ignite, keep oven door closed, turn oven off and disconnect the power supply. f. Close supervision is necessary when using disposable containers made from plastic, paper or other combustible material. 4. TO reduce the risk of explosion and sudden boiling: a. Do not place sealed containers in the oven. Baby bottles fitted with a screw cap or teat are considered to be sealed containers. b. When boiling liquid in the oven, use the wide -mouthed container and stand about 20 seconds at the end of 5 cooking to avoid delayed eruptive boiling of liquids. c. Potatoes, sausage and chestnut should be peeled or pierced before cooking. Eggs in their shell, whole hard -boiled eggs should not be heated in microwave ovens since they may explode, even after microwave heating has ended. d. The cooked liquid should not be removed out immediately. Several moments should be waited before removing. In order to avoid possible hazards caused by delayed eruptive boiling of 1iquids. e. The contents of feeding bottles and baby food jars are to be stirred or shaken and the temperature is to be checked before consumption, in order to avoid burns. 5. Never operate the oven further if the door or door seals is damaged or the oven is malfunctioned or supply cord is damaged. Return the appliance to the nearest authorised service center for repair and maintenance. Never try to adjust or repair the oven yourself. 6. If t…

Text truncated - open the document above for the full version.

2024-6- FEDER Authori 7435 O Columb Ref: At Grantee Guang d applicat below r an agen or the c Emerso designa Design a Name: E Address FRN: 00 Tel.: +1 Email: b Signed Signatu Applic Address FRN: 0 Tel: 07 6 Email: g Signed Signat u -22 RAL COMM ization and akland Mil l bia, MD 210 ttestation St e code: YI4 dong Welly tion, Emers referenced F nt for no less conclusion o on Radio Co ated U.S. ag ated U.S. A Emerson Rad s: 959 Route 026321828 (973)42824 bleung@eme by (printed ure: ant: Guangd s: Fusha Indu 019939883 60-2250701 gaoyanjun@ by (printed ure: U.S. AG MUNICATI Evaluation ls Road 046 tatements C ; FCC ID: Y Electrical A son Radio C FCC ID.Gua s than one y of any Comm orp. accepts gent for serv Agent Inform dio Corp. 46 East, Sui 436 ersonradio.co name): Bri dong Welly ustrial Park, Fu 15 @weili.com name): Yan GENT LE IONS COM Division FR 47 §2.9 YI4DWB20PA Appliances Corp. is our angdong W year after th mission-rela , as of the d vice of proce mation: te 210,2 nd Flo om ian Leung y Electrical usha Town, Z m.cn njun Gao ETTER O MMISSIONS 11(d)(7) Fil AS03 Co.,Ltd cer designated Welly Electri he grantee h ated procee date of the fi ess for the b oor, Parsippa Appliances hongshan City OF ATTE S ling rtifies that, a U.S. agent cal Applian has terminate eding involv filing of the below refere any, NJ 0705 Co.,Ltd y, Guangdong STATION as of the dat for service nces Co.,Ltd ed all mark ving the equ application enced FCC 54 g Province, P. N te of the fili of process f daccepts to eting and i m uipment. n, the obliga ID. R. China ing of the for the maintain mportation ation of the

Guangd Address Tel: 076 Email: g Fax: 076 Date: 20 FEDER Authori 7435 O Colum b Ref: A t FCC I D Guangd authori authori Sincer e Signat u Print Na Title: E dong Welly E s: Fusha Indu 60-22507015 gaoyanjun@ 60‐22507100 024/06/22 RAL COMM ization and akland Mil l bia, MD 210 ttestation St D: YI4DWB ong Welly E zation is so zation purs ely, ure ame:Gao Ya Engineer Electrical Ap ustrial Park, Fu 5 @weili.com.cn 0‐1080 MUNICATI Evaluation ls Road 046 tatements C B20PAS03 lectrical App ught, is not uant to sec anjun ppliances Co usha Town, Zh n Att IONS COM Division FR 47 §2.9 pliances Co.,L t “covered” ction 2.903 o .,Ltd hongshan City testation L MMISSIONS 11(d)(5)(i) Ltd certifies equipment of the FCC r C y, Guangdong Letter S Filing s that the e t prohibited rules. CFR 47 §2.91 g Province, P. quipment f d from rece 1(d)(5)(i) Atte R. China for which iving an eq u estation Letter uipment r

Guangd Address Tel: 076 Email: g Fax: 076 Date: 20 FEDE R Authori 7435 O Colum b Ref: A t FCC I D Guangd applicat equipm Sincer e Signat u Name: G Title:E n dong Welly E s: Fusha Indu 60-22507015 gaoyanjun@ 60‐22507100 024/06/22 RAL COMM ization and akland Mil l bia, MD 210 ttestation St D: YI4DWB dong Welly tion, the app ment. ely, ure: Gao Yanjun ngineer Electrical Ap ustrial Park, Fu 5 @weili.com.cn 0‐1080 MUNICATI Evaluation ls Road 046 tatements C B20PAS03 Electrical A plicant is no n ppliances Co usha Town, Zh n Att IONS COM Division FR 47 §2.9 Appliances C ot identified .,Ltd hongshan City testation L MMISSIONS 11(d)(5)(ii) Co.,Ltd cert d on the Cov CF y, Guangdong Letter S ) Filing tifies that as vered List a FR 47 §2.911 g Province, P. s of the date as an entity (d)(5)(ii) Atte R. China e of the filin producing “ estation Letter ng of the “covered” r

Guangdong Welly Electrical Appliances Co., Ltd Address: Fusha Industrial Park, Fusha Town, Zhongshan City, Guangdong Province, P. R. China Tel: 0760-22507015 Email: [email protected] Fax: 0760‐22507100‐1080 FCC Confidential Authorization Date: 2024/06/22 FEDERAL COMMUNICATIONS COMMISSIONS Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Subject: Confidentiality Request regarding application for certification of FCC ID: YI4DWB20PAS03 In accordance with Sections 0.457 and 0.459 of the Commission’s Rules, Guangdong Welly Electrical Appliances Co., Ltd hereby requests long-term confidential treatment of information accompanying this application as outlined below:  Block Diagram  Schematics  Operation Description The above materials contain proprietary and confidential information not customarily released to the public. The public disclosure of these materials provides unjustified benefits to its competitors in the market. Sincerely Yours, Signature: Print Name: Gao Yanjun Title: Engineer

Guangdong Welly Electrical Appliances Co., Ltd Address: Fusha Industrial Park, Fusha Town, Zhongshan City, Guangdong Province, P. R. China Tel: 0760-22507015 Email: [email protected] Fax: 0760‐22507100‐1080 QA-FR-170-B 7/29/2014 FCC Authorization Date: 2024/06/22 FEDERAL COMMUNICATIONS COMMISSIONS Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Subject: Agent Authorization To whom it may concern: We Guangdong Welly Electrical Appliances Co., Ltd the undersigned, hereby authorizes World Alliance Testing and Certification (Shenzhen) Co., Ltd to act on its behalf in all matters relating to application for Equipment authorization, including the signing of all documents relating to these matters. All acts carried out by World Alliance Testing and Certification (Shenzhen) Co., Ltd on our behalf shall have the same effect as our own action. We, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. This authorization is valid until further written notice from the applicant. Sincerely Yours, Signature: Print Name: Gao Yanjun Title: Engineer

Report No.: 2405T30137E Page 1 of 4 EUT EXTERNAL PHOTOGRAPHS Report No.: 2405T30137E Page 2 of 4 Report No.: 2405T30137E Page 3 of 4 Report No.: 2405T30137E Page 4 of 4

CERTAIN INTERNAL PARTS ARE INTENTIONALL Y NOT GROUNDED WARNING - This Device is to be Serviced Only by Properly Qualified Service Personnel. Consult the Service Manual for Proper Service Procedures to Assure Continued Compliance with the Federal Performance Standard for Microwave Ovens and for Precautions to be Taken to Avoid Possible Exposure to Excessive Microwave Energy. CAUTION- TO ENSURE CONTINUED PROTECTION AGAINST ELECTRICAL SHOC K HAZARD, CONNECT TO PROPERLY GROUNDED OUTLETS ONLY. DISCONNECT APPLIANCE BEFORE SERVICING. REMOVAL OF OUTERCASE WITH PRODUCT ENERGIZED MAY EXPOSE SERVICEMAN TO HAZARDOUS HIGH VOLTAGE POTENTIALS. WARNING- AND MAY PRESENT A RISK OF ELECTRIC SHOCK ONLY DURING SERVICING. SERVICE PERSONNEL - DO NOT CONTACT THE FOLLOWING PARTS WHILE THE APPLIANCE IS ENERGIZED: If provided Fan Motor, Turntable Motor, Damper Motor, L. V.Transfo rmer( Touch Control Type) or Timer Motor Assembl y (Mechanical Type). WARNING - Ri s k of electric Shock. Non-r emovable fa steners are provided because of internal high voltages. Do not remove fa steners . FOR HOUSEHOLD USE ONLY. AVERTISSEMENT Risque de secousse électrique. A cause du ni veau élevé de tension à l'intérieur le s éléments de fi xation fournis ne sont pas amovibles. À USAGE DOMESTIQUE UNIQUEMENT ATTENTION- L'entretien de cet appareil doit être fait par un technicien qualifié. Consulter le manuel d'entretien pour connaître les mesures d'entretien appropriées, assurer que l'appareil est toujours conforme aux exigences fédérales concernant les fours à micro-ondes et pour les précautions à prendre pour éviter toute exposition excessive à l'énergie des micro-ondes. AVERTISSEMENT- AVERTISSEMENT- AVERTISSEMENT- Pour assurer une protection continue contre les risques de choc électrique, ne brancher l'appareil qu'à des prises de courant reliées à la terre. Débrancher l'appareil avant d'en faire l'entretien. Enlever le boîtier extérieur lorsque l' appareil est toujours en circuit expose le technicien à des décharges électriques dangereuses. Certaines pièces internes ne sont pas, à dessein, mises à la terre et peuvent présenter un risque de secousse électrique, seulement durant l'entretien. Technicien Ne pas toucher aux pièces suivantes lorsque l'appareil est sous tension : s elon le cas, le moteur du ventilateur, le moteur du plateau tournant, le moteur du registre, le transformateur B.T. (commande électronique) ou l'assemblage du moteur de la minuterie (commande mécanique). MICROWAVE OVEN (HOUSEHOLD) MODEL NO.: B20PAS03-A70 MANUFACTURED: 060124 POWER INPUT 120V~ 60Hz, 1150W(Microwave) 1500W(AIR FRY) SINGLE PHASE WITH GROUNDING, OUTPUT 700W, 2450MHz FCC ID: YI4DWB20PAS03 MADE IN CHINA THIS DEVICE COMPLIES WITH DHHS RADIATION PERFORMANCE STANDARDS 21 CFR SUBCHAPTER J. FOUR À MICRO-ONDES (DOMESTIQUE) No de modèle :B20PAS03-A70 DATE DE FABRICATION: 060124 ALIMENTATION CA DE 120V~ 60Hz, 1150W 1 500W MONOPHASÉ avec prise de terre PUISSANCE 700W, 2450MH z FABRIQUÉ EN CHINE CET APPAREIL EST CONFORME AUX NORMES DE RAYONNEMENT THERMIQUE DU DHHS, CODE 21 DU CFR, ALINÉA J. 200mm 147mm Guangdong Welly Electrical Appliances Co., Ltd. Fusha Industrial Park, Fusha Town, Zhongshan City, Guangdong Province.P.R. China Not For Built-In Installation

EXHIBITA-FCC ID LABEL AND LOCATION FCC ID Label FCC ID Label Location Information The label shown shall be permanently affixed at a conspicuous location on the device and be readily visible to the time purchase (Labeling requirements per 2.295)

Report No.: 2405T30137E Page 1 of 11 EUT INTERNAL PHOTOGRAPHS Report No.: 2405T30137E Page 2 of 11 Report No.: 2405T30137E Page 3 of 11 Report No.: 2405T30137E Page 4 of 11 Report No.: 2405T30137E Page 5 of 11 Report No.: 2405T30137E Page 6 of 11 Report No.: 2405T30137E Page 7 of 11 Report No.: 2405T30137E Page 8 of 11 Report No.: 2405T30137E Page 9 of 11 Report No.: 2405T30137E Page 10 of 11 Report No.: 2405T30137E Page 11 of 11

Report No.: 2405T30137EA Report Template: TR-4-E-013/V1.0 Page 20 of 22 3.7 Radio frequency exposure Test Date: 2024-05-30 Test By: Lirou Li Environment condition: Temperature: 23.7C; Relative Humidity:61%; ATM Pressure: 101.4kPa Radiation leakage was measured in the as-received condition with the oven door closed using a microwave leakage meter. A 275mL water load was placed in the center of the oven and the oven was operated at maximum output power. There was no microwave leakage exceeding a power level of 0.16mW/cm2 observed at any point 5 cm or more from the external surface of the oven. A maximum of 1.0mW/cm2 is allowed in accordance with the applicable Federal Standards. Hence, microwave leakage in the as-received condition with the oven door closed was below the maximum allowed.

Report No.: 2405T30137EA Report Template: TR-4-E-013/V1.0 Page 1 of 22 FCC Test Report Report No.: 2405T30137EA Applicant: Guangdong Welly Electrical Appliances Co.,Ltd Address: Fusha Industrial Park, Fusha Town, Zhongshan, Guangdong, P.R.China Product Name: Microwave oven Product Model: B20PAS03-A70 Multiple Models: N/A Trade Mark: N/A FCC ID: YI4DWB20PAS03 Standards: FCC CFR Title 47 Part 18 Test Date: 2024-05-29 to 2024-05-30 Test Result: Complied Report Date: 2024-06-04 Reviewed by: Approved by: Frank Yin Project Engineer Jacob Kong Manager Prepared by: World Alliance Testing & Certification (Shenzhen) Co., Ltd No. 1002, East Block, Laobing Building, Xingye Road 3012, Xixiang street, Bao'an District, Shenzhen, Guangdong, People’s Republic of China This report may contain data that are not covered by the NVLAP accreditation and shall be marked with an asterisk “★” Report No.: 2405T30137EA Report Template: TR-4-E-013/V1.0 Page 2 of 22 Announcement 1. This test report shall not be reproduced except in full, without the written approval of World Alliance Testing & Certification (Shenzhen) Co., Ltd 2. The results in this report apply only to the sample tested. 3. This sample tested is in compliance with the limits of the above regulation. 4. This report must not be used by the client to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the U.S. Government. 5. The information marked “#” is provided by the applicant, the laboratory is not responsible for its authenticity and this information can affect the validity of the result in the test report. Customer model name, addresses, names, trademarks etc. are included. Revision History Version No. Issued Date Description 00 2024-06-04 Original Report No.: 2405T30137EA Report Template: TR-4-E-013/V1.0 Page 3 of 22 Contents 1 General Information ............................................................................................................................ 4 1.1 Client Information ...................................................................................................................... 4 1.2 Product Description of EUT ....................................................................................................... 4 1.3 Related Submittal(s)/Grant(s) .................................................................................................... 4 1.4 Measurement Uncertainty ......................................................................................................... 4 1.5 Laboratory Location ................................................................................................................... 5 1.6 Test Methodology ...................................................................................................................... 5 2 Description of Measurement .............................................................................................................. 6 2.1 Test Configuration ...................................................................................................................... 6 2.2 Test Auxiliary Equipment ........................................................................................................... 6 2.3 Test Setup .................................................................................................................................. 6 2.4 Test Procedure .......................................................................................................................... 8 2.5 Measurement Method................................................................................................................ 9 2.6 Measurement Equipment ........................................................................................................ 10 3 Test Results ....................................................................................................................................... 11 3.1 Test Summary ........................................................................................................................... 11 3.2 Limit .......................................................................................................................................... 11 3.3 Operating frequencies ............................................................................................................. 12 3.4 Power Output Measurement ................................................................................................... 13 3.5 AC Line Conducted Emissions Test Data ................................................................................ 14 3.6 Radiated emission Test Data ................................................................................................... 16 3.7 Radio frequency exposure ...................................................................................................... 20 4 Test Setup Photo ............................................................................................................................... 21 5 E.U.T Photo ........................................................................................................................................ 22 Report No.: 2405T30137EA Report Template: TR-4-E-013/V1.0 Page 4 of 22 1 General Information 1.1 Client Information Applicant: Guangdong Welly Electrical Appliances Co.,Ltd Address: Fusha Industrial Park, Fusha Town, Zhongshan, Guangdong, P.R.China Manufacturer: Guangdong Welly Electrical Appliances Co.,Ltd Address: Fusha Industrial Park, Fusha Town, Zhongshan, Guangdong, P.R.China 1.2 Product Description of EUT The EUT is Microwave Over operate on 2450MHz ISM frequency Band. Sample Serial Number 2M2K-1(assigned by WATC) Sample Received Date 2024-05-27 Sample Status Good Condition Operating Frequency Range 2450MHz±50.0 MHz Power Supply AC 120V/60Hz Microwave Rated Input Power # 1150W Microwave Rated Output Power # 700W Modification Sample No Modification by th…

Text truncated - open the document above for the full version.

Report No.: 2405T30137E Page 1 of 3 TEST SETUP PHOTOGRAPHS AC Line Conducted Emission Report No.: 2405T30137E Page 2 of 3 Radiated Emission Below 1GHz Report No.: 2405T30137E Page 3 of 3 Above 1 GHz