YI4DWMW001GHousehold Microwave Oven

INSTRUCTION MANUAL Cordless Microwave Oven MW001G ENGLISH: Original instructions IMPORTANT: Read Before Using. 2 ENGLISH INTRODUCTION SPECIFICATIONS Model:MW001G Rated voltageD.C. 36 V - 40 V max Microwave power500 W / 350 W Dimensions (W x L x H) External dimensions343 mm x 318 mm x 338 mm (13-1/2” x 12-1/2” x 13-1/4”) (Without battery cartridge) (With the handle lowered position) Cavity255 mm x 241 mm x 120 mm (10” x 9-1/2” x 4-3/4”) Capacity8 L Net weight *19.9 - 13.1 kg (21.8 - 28.9 lbs) (With battery cartridges) *1 The lightest and heaviest combinations according to battery cartridges are shown in the table. • Due to our continuing program of research and development, the specifications herein are subject to change without notice. • Specifications may differ from country to country. Estimated operating time Battery cartridge (Full charged)500 W350 W BL4020 x 26 min8 min BL4025 x 29 min13 min BL4040 x 215 min21 min BL4050F x 223 min33 min BL4080F x 237 min52 min NOTE: Values are approximate and may differ depending on charging status, and usage condition. NOTE: The estimated operating time with one battery is about half of the amount when using two batteries. Applicable battery cartridge and charger Battery cartridgeBL4020 / BL4025 / BL4040 / BL4050F / BL4080F ChargerDC40RA / DC40RB / DC40RC • Some of the battery cartridges and chargers listed above may not be available depending on your region of residence. WARNING: Only use the battery cartridges and chargers listed above. Use of any other battery cartridges and chargers may cause injury and/or fire. Household use only SAVE THESE INSTRUCTIONS READ CAREFULLY AND KEEP FOR FUTURE IMPORTANT SAFEGUARDS WARNING: This appliance should be serviced only by qualified service personnel. Contact nearest authorized service facility for examination, repair, or adjustment. WARNING: DO NOT attempt to operate this oven with the door open, since open-door operation can result in harmful exposure to microwave energy. WARNING: If the door(bent),hinges(broken or loosened), door seals or sealing surface are dam- aged, the oven must not be operated until it has been repaired by a trained person. WARNING: It is hazardous for anyone other than a trained person to carry out any service or repair operation, which involves the removal of any cover, which gives protection against exposure to micro- wave energy. WARNING: Use this appliance only for its intended use as described in the manual. WARNING: Do not use corrosive chemicals or vapors in this appliance. WARNING: This type of oven is specifically designed to heat, cook, or dry food. It is not designed for industrial or laboratory use. WARNING: Liquids or other food must not be heated in sealed containers since they are liable to 3 ENGLISH explode. 1. Do not sit on and step on the appliance. Do not place objects on the appliance. 2. This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabil- ities or lack of experience and knowledge if they have been given supervision or instruc- tion concerning use of the appliance in a safe way and understand the hazards involved. 3. Children shall not play with the appliance. 4. If smoke is observed, switch off the appliance and remove the battery and keep the door closed in order to stifle any flames. 5. When there is no food in the microwave oven, do not operate the microwave oven. Otherwise the appliance may be damaged. 6. Do not pierce the oven door mesh. Otherwise it will cause microwave leakage. 7. Do not operate the appliance in enclosed spaces such as cabinet. 8. Place the appliance on a level and flat surface. 9. Do not operate the appliance while suspended. Do not use the handle any other purpose than carrying the appliance. 10. Do not move the appliance during operation. 11. DO NOT use the appliance in the rain. Do not wet the appliance. If the appliance is exposed to water, have it inspected by Makita Authorized or Factory Service Centers. 12. Do not store this appliance outdoors. Do not use this product near water – for example, near a kitchen sink, in a wet basement, near a swim- ming pool, or similar locations. 13. To reduce the risk of electrical shock, do not put microwave oven in water or other liquid. Do not place or store product where it can fall or be pulled into a tub or sink. 14. If the appliance get an impact or falls, send the appliance to the after-sales department for inspection and maintenance in time. 15. Do not cover or block any openings on the appliance. 16. It is forbidden to heat inflammables and explo- sives, especially dry ice. 17. Only use utensils that are suitable for use in microwave ovens. 18. Metallic containers for food and beverages are not allowed during microwave cooking. 19. When heating food in plastic or paper contain- ers, keep an eye on the oven due to the possi- bility of ignition. 20. Liquids, such as water, coffee, or tea are able to be overheated beyond the boiling point without appearing to be boiling. Visible bubbling or boiling when the container is removed from the microwave oven is not always present. THIS COULD RESULT IN VERY HOT LIQUIDS SUDDENLY BOILING OVER WHEN THE CONTAINER IS DISTURBED OR A UTENSIL IS INSERTED INTO THE LIQUID. 21. The contents of feeding bottles and baby food jars are to be stirred or shaken and the tem- perature is to be checked before consumption, in order to avoid burns. 22. Eggs in their shell and whole hard boiled eggs shall not be heated in microwave ovens since they may explode, even after microwave heat- ing has ended. 23. Do not place inflammables and combustibles near the microwave oven. 24. During the operation of the microwave oven, keep your eyes on the cooking condition of the microwave oven at any time. Set the correct cooking time. Overtime cooking may cause fire. 25. In the cooking process of light load food with less water content, due to the different micro- wave absorption capacity of different sub- …

Text truncated - open the document above for the full version.

Zhongshan Donlim Weili Electrical Appliances Co.,Ltd. Address: Fusha Industrial Park, Fusha Town, Zhongshan, China Tel: 0760-22507145 Email: [email protected] Fax: 0760‐22507100‐ 1080 FCC Authorization 2022-11-8 FEDERAL COMMUNICATIONS COMMISSIONS Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Subject: Agent Authorization To whom it may concern: We, Zhongshan Donlim Weili Electrical Appliances Co., Ltd., the undersigned, hereby authorize Shenzhen Accurate Technology Co., Ltd. to act on its behalf in all matters relating to application for Equipment authorization, including the signing of all documents relating to these matters. All acts carried out by Shenzhen Accurate Technology Co., Ltd. on our behalf shall have the same effect as our own action. We, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988,21 U.S.C. 862. This authorization is valid until further written notice from the applicant. Sincerely Yours, Signature: Print Name: Jianli Yang Title: Engineer QA-FR-170-B

Zhongshan Donlim Weili Electrical Appliances Co.,Ltd. Address: Fusha Industrial Park, Fusha Town, Zhongshan, China Tel: 0760-22507145 Email: [email protected] Fax: 0760‐22507100‐1080 FCC Confidential Authorization 2022-11-8 FEDERAL COMMUNICATIONS COMMISSIONS Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Subject: Confidentiality Request regarding application for certification of FCC ID: YI4DWMW001G In accordance with Sections 0.457 and 0.459 of the Commission’s Rules, Zhongshan Donlim Weili Electrical Appliances Co., Ltd. hereby requests long-term confidential treatment of information accompanying this application as outlined below:  Block Diagram  Schematics  Operation Description The above materials contain proprietary and confidential information not customarily released to the public. The public disclosure of these materials provides unjustified benefits to its competitors in the market. Sincerely Yours, Signature: Print Name: Jianli Yang Title: Engineer

Shenzhen Accurate Technology Co., Ltd. Project No.: SZ2221009-45800E-EM-01 External Photos Page 1 of 4 External Photos Shenzhen Accurate Technology Co., Ltd. Project No.: SZ2221009-45800E-EM-01 External Photos Page 2 of 4 Shenzhen Accurate Technology Co., Ltd. Project No.: SZ2221009-45800E-EM-01 External Photos Page 3 of 4 Shenzhen Accurate Technology Co., Ltd. Project No.: SZ2221009-45800E-EM-01 External Photos Page 4 of 4

Shenzhen Accurate Technology Co., Ltd. Project No.: SZ2221009-45800E-EM-01 EXHIBITA-FCC ID LABEL AND LOCATION FCC ID Label Shenzhen Accurate Technology Co., Ltd. Project No.: SZ2221009-45800E-EM-01 FCC ID Label Location Information The label shown shall be permanently affixed at a conspicuous location on the device and be readily visible to the time purchase (Labeling requirements per 2.295)

Shenzhen Accurate Technology Co., Ltd. Project No.: SZ2221009-45800E-EM-01 Internal Photos Page 1 of 8 Internal Photos Shenzhen Accurate Technology Co., Ltd. Project No.: SZ2221009-45800E-EM-01 Internal Photos Page 2 of 8 Shenzhen Accurate Technology Co., Ltd. Project No.: SZ2221009-45800E-EM-01 Internal Photos Page 3 of 8 Shenzhen Accurate Technology Co., Ltd. Project No.: SZ2221009-45800E-EM-01 Internal Photos Page 4 of 8 Shenzhen Accurate Technology Co., Ltd. Project No.: SZ2221009-45800E-EM-01 Internal Photos Page 5 of 8 Shenzhen Accurate Technology Co., Ltd. Project No.: SZ2221009-45800E-EM-01 Internal Photos Page 6 of 8 Shenzhen Accurate Technology Co., Ltd. Project No.: SZ2221009-45800E-EM-01 Internal Photos Page 7 of 8 Shenzhen Accurate Technology Co., Ltd. Project No.: SZ2221009-45800E-EM-01 Internal Photos Page 8 of 8

Note: This report may contain data that are not covered by the A2LA accreditation and are marked with an asterisk “★”. Shenzhen Accurate Technology Co., Ltd. is not responsible for the authenticity of any test data provided by the applicant. Data included from the applicant that may affect test results are marked with an asterisk ’*’. Customer model name, addresses, names, trademarks etc. are not considered data. This report cannot be reproduced except in full, without prior written approval of the Company. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested. This report is valid only with a valid digital signature. The digital signature may be available only under the Adobe software above version 7.0. Shenzhen Accurate Technology Co., Ltd. 1/F., Building A, Changyuan New Material Port, Science & Industry Park, Nanshan District, Shenzhen, Guangdong, P.R. China Tel: +86 755-26503290 Fax: +86 755-26503396 Web: www.atc-lab.com Version 25: 2021-11-15 Page 1 of 19 FCC-Part 18 TEST REPORT Applicant Name : Zhongshan Donlim Weili Electrical Appliances Co.,Ltd. Address : Fusha Industrial Park, Fusha Town, Zhongshan City, Guangdong Province, China Report Number : SZ2221009-45800E-EM-01 FCC ID: YI4DWMW001G Test Standard (s) FCC Part 18 Sample Description Product Type: Cordless Microwave Model No.: MW001G Trade Mark: Makita Date Received: 2022-10-09 Date of Test: 2022-10-13 to 2022-10-14 Report Date: 2022-11-02 Test Result: Pass* * In the configuration tested, the EUT complied with the standards above. Prepared and Checked By: Approved By: Zeki.Ma Candy Li EMC Engineer EMC Engineer Shenzhen Accurate Technology Co., Ltd. Report No.: SZ2221009-45800E-EM-01 Version 25: 2021-11-15 Page 2 of 19 FCC-Part 18 TABLE OF CONTENTS GENERAL INFORMATION ....................................................................................................................................... 3 PRODUCT DESCRIPTION FOR EQUIPMENT UNDER TEST (EUT) ..................................................................................... 3 OBJECTIVE ................................................................................................................................................................... 3 TEST METHODOLOGY .................................................................................................................................................. 3 MEASUREMENT UNCERTAINTY .................................................................................................................................... 3 TEST FACILITY ............................................................................................................................................................. 4 OPERATING CONDITION/TEST CONFIGURATION .......................................................................................... 5 JUSTIFICATION ............................................................................................................................................................. 5 EUT EXERCISE SOFTWARE .......................................................................................................................................... 5 SPECIAL ACCESSORIES ................................................................................................................................................. 5 EQUIPMENT MODIFICATIONS ....................................................................................................................................... 5 SUPPORT EQUIPMENT LIST AND DETAILS .................................................................................................................... 5 EXTERNAL CABLE LIST AND DETAILS ......................................................................................................................... 5 CONFIGURATION OF TEST SETUP ................................................................................................................................. 5 BLOCK DIAGRAM OF TEST SETUP ................................................................................................................................ 6 SUMMARY OF TEST RESULT ................................................................................................................................. 7 TEST EQUIPMENT LIST ........................................................................................................................................... 8 FCC §18.313, §1.1310, §2.1091- MAXIMUM PERMISSIBLE EXPOSURE ........................................................... 9 APPLICABLE STANDARD .............................................................................................................................................. 9 MEASUREMENT ............................................................................................................................................................ 9 RADIATION HAZARD MEASUREMENT ............................................................................................................. 10 APPLICABLE STANDARD ............................................................................................................................................ 10 ENVIRONMENTAL CONDITIONS .................................................................................................................................. 10 INPUT POWER ............................................................................................................................................................. 10 LOAD FOR CORDLESS MICROWAVES .......................................................................................................................... 10 RF OUTPUT POWER MEASUREMENT .......................................................................................................................... 10 OPERATING FREQUENCY MEASUREMENT ................................................................…

Text truncated - open the document above for the full version.

Shenzhen Accurate Technology Co., Ltd. Project No.: SZ2221009-45800E-EM-01 Test Photos Page 1 of 2 Radiated Spurious Emissions Test View (Below 1GHz) Shenzhen Accurate Technology Co., Ltd. Project No.: SZ2221009-45800E-EM-01 Test Photos Page 2 of 2 Radiated Spurious Emissions Test View (Above 1GHz)