YJ4CMGYZCDCZ31Zigbee Modular Device

EMKUT0115-02 1 Consert ® Tru Load Device Controller Data Sheet Part Numbers: CDCZ24S–3.1 (No Relay) CDCZ24RS-NC–3.1 (Relay) CDCZ24RS-NO–3.1 (Relay) Overview: Utilizing standards-based hardware and hardware interfaces to ensure universal connectivity, the Consert ® Tru Load Device Controller measures metrology data of devices of up to 50 amps of service for HVACs and 30 or 40 amps of service for electric water heaters, and pool pumps in compliance with ANSI C12.1 accuracy requirements. This real-time empirical data collection is aggregated and delivered to the Consert Tru Smart Energy Gateway via the onboard ZigBee ® wireless radio communications. Offering a new level of intelligence and control at the device level, the Consert Load Device Controller when paired with the Smart Energy Gateway empowers homeowners and small businesses to participate in cost saving activities overseen by their utilities that help both parties benefit economically and environmentally. Features and Benefits  True load management: o Real-time data collection o Real-time data reporting o Empirical power measurement compliant with ANSI C12.1 accuracy requirements o Absolute device management by utility and its customers  Rated to 50 AMPS without a relay (CDCZ24S 3.1)  Rated to 40 AMPS/2HP (CDCZ24RS-NO-3.1) with a relay  Rated to 30 AMPS/1.5 HP (CDCZ24RS-NC-3.1) with a relay  Firmware over-the-air upgradeable  Wireless ZigBee ® 1.0 SEP upgradable to 2.0  Controls HVACs, heat pumps, hot water heaters, pool pumps, and other high consumption electrical equipment  Status and error LEDs Power Measurement  Power Measurement compliant with ANSI C12.1 accuracy requirements  Measured Values: o RMS Voltage o RMS Current o Apparent Power o Reactive Power o Accumulative Energy o Load Duty Cycle  Supports wide-band (line harmonics) and narrow-band (no harmonic) measurements EMKUT0115-02 2 Human Interface Externally visible diagnostic status LEDs Environment  Industrial temperature rated parts (-40C to +85C)  Assembled device controller temperature range -40° C to +65° C  UL916 rated enclosure; UL50 and UL50E ratings pending Electrical  Wide voltage range support - 120-240 VAC Security  Rain-tight enclosure with plastic padlock seal for tamper detection  Chip security  Secure two-way communications Communications  ZigBee ® SEP 1.x upgradable to 2.0 Regulatory Information  FCC ID: YJ4CMGYZCDCZ31  Certified to UL916  Complies with Part 15 of the FCC Rules.  USA-Federal Communications Commission (FCC) Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation. Cautions: ◘ Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. ◘ Exposure to Radio Frequency Radiation. To comply with FCC RF exposure compliance requirements, a separation distance of at least 20 cm must be maintained between the antenna of this device and all persons. This device must not be co-located or operating in conjunction with any other antenna or transmitter. EMKUT0115-02 3 Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:  Reorient or relocate the receiving antenna.  Increase the separation between the equipment and receiver.  Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.  Consult the dealer or an experienced radio/TV technician for help. Consert Inc. 12508 Jones Maltsberger Road, Suite 110 San Antonio, TX 78247 www.consert.com P 210-494-1525 / F 210-494-1541 COPYRIGHT 2010–2011 Consert Inc. All rights reserved. The Consert solution is covered by U.S. Pat. No. 7,715,951 and other U.S. and international patents pending. A list of patents and published patent applications relating to the Consert solution may be found at www.consert.com. Consert, Communicate-Control-Conserve, Virtual Peak Plant, and the Consert logo are trademarks or registered trademarks of Consert Inc. ZigBee ® is a registered trademark of the ZigBee Alliance.

EHWVN0114-01 July 1, 2011 Installation Guide Model Numbers: CDCZ24S 3.1 CDCZ24RS-NC-3.1 CDCZ24RS-NO-3.1 Device Controller Hardware Installation Instructions EHWVN0114-01 2 Consert Inc. 12508 Jones Maltsberger Road, Suite 110 San Antonio, TX 78247 P 210-494-1525 / F 210-494-1541 www.consert.com The Consert solution is covered by U.S. Pat. No. 7,715,951 and other U.S. and international patents pending. A list of patents and published patent applications relating to the Consert solution may be found at www.consert.com/patents. Consert, Communicate-Control-Conserve, Virtual Peak Plant, and the Consert logo are trademarks or registered trademarks of Consert Inc. ZigBee is a registered trademark of the ZigBee Alliance Hardware Tru Load Device Controller Installation EHWVN0114-01 3 CONTENTS Introduction ....................................................................................................................4 Before You Start ..............................................................................................................5 Supplies Needed for Each Installation .................................................................................. 5 When You Arrive at the Installation Site .............................................................................. 7 Installation Instructions ..................................................................................................8 Installing a Tru Load Device Controller to an HVAC Unit ...................................................... 8 Before Starting This Procedure .................................................................................................... 8 Installation Procedure ................................................................................................................. 8 Installing a Tru Load Device Controller to 240-VAC Equipment .......................................... 10 Before Starting This Procedure .................................................................................................. 10 Installation Procedure ............................................................................................................... 10 Installing a Tru Load Device Controller to 120-VAC Equipment .......................................... 12 Before Starting This Procedure .................................................................................................. 12 Installation Procedure ............................................................................................................... 12 Appendix A. Approved Device Controller Attachment Methods .................................14 Appendix B. Environmental Specifications .................................................................15 Appendix C. Regulatory Information ..........................................................................16 Tru Load Device Controller Installation EHWVN0114-01 4 INTRODUCTION Utilizing standards-based hardware and hardware interfaces to ensure universal connectivity, the Con- sert ® Tru Load Device Controller measures metrology data of devices of up to 50 amps of service, or 2 HP, such as HVACs, electric water heaters, and pool pumps in compliance with ANSI C12.1 accuracy require- ments. This real-time empirical data collection is aggregated and delivered to the Consert Tru Smart En- ergy Gateway via the onboard ZigBee ® wireless radio communications. Offering a new level of intelligence and control at the device level, the Consert Tru Load Device Controller when paired with the Smart Energy Gateway empowers homeowners and small businesses to participate in cost saving activities overseen by their utilities that help both parties benefit economically and environmentally. For environmental specifications see Appendix B: Environmental Specifications on page 15, and for regu- latory information, including the FCC ID, see Appendix C: Regulatory Information on page 16. Tru Load Device Controller Installation EHWVN0114-01 5 BEFORE YOU START These instructions describe how to install the Consert Tru Load Device Controllers for use with the Con- sert® energy management solution. These Device Controllers can be installed on 120-VAC or 240-VAC equipment such as HVACs, electric water heaters, and pool pumps rated under 2 HP or 50 Amps. ■ The Tru Load Device controllers should be installed according to the National Electrical Code (NEC) and local code requirements. ■ Read all instructions before proceeding with the installation. ■ For assistance, please contact Consert Installation Support at the numbers provided by the Consert Project Manager. SUPPLIES NEEDED FOR EACH INSTALLATION The following supplies are required for each installation. Refer to the work order for specifics for each participant, such as equipment to be controlled. The following will be supplied for each installation, as required: ■ One Tru Load Device Controller without a relay (CDCZ24S 3.1) for each HVAC unit. These device con- trollers carry up to a maximum load of 50 amps, based on minimum circuit ampacity (MCA) listed on the nameplate. ■ One Tru Load Device Controller with a relay for each electric water heater, or other controlled equipment, such as a pool pump, as follows: ◘ For equipment that has a maximum load of 40 amps or a maximum HP rating of 2HP, use model number CDCZ24RS NO 3.1. ◘ For equipment that as a maximum load of 30 amps or a maximum HP rating of 1.5 HP, use model number CDCZ24RS-NC-3.1. ■ #6, #8, #10, #12, and #14 black wire to make jumpers for the disconnects or panel. The different wire sizes are required for the various conditions that will be encountered in the field. #10 and #12 are the most common sizes used and each installation uses a minimum of 6” of wire for each jumper. ■ Romex: ◘ #10 romex, 2-wire with ground, for connecting to the water heater. ◘ ½” or ¾” romex clamp connectors. The romex is used to make the connections to the water heater when the Tru Load Device controlle…

Text truncated - open the document above for the full version.

FCCID: YJ4CMGYZCDCZ31 Report No.: 31151351.001 Page 2 of 69 The test results contained in this report refer exclusively to the product(s) presented for testing. No liability may be assumed for models or products not referred to herein. This test report may not be published or duplicated in part without permission of the testing body. This test report by itself does not constitute authorization for the use of any TUV Rheinland test mark. The report must not be used by the client to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the Federal Government. TUV Rheinland of North America, Inc., 762 Park Avenue, Youngsville, NC 27596-9470, Tel: 919-554-3668, Fax: 919-554-3542 QF09B040 Revision 0 Manufacturer’s statement - attestation The manufacturer; Consert, Incorporated, as the responsible party for the equipment tested, hereby affirms: a) That he has reviewed and concurs that the test shown in this report are reflective of the operational characteristics of the device for which certification is sought; b) That the device in this test report will be representative of production units; c) That all changes (in hardware and software/firmware) to the subject device will be reviewed. d) That any changes impacting the attributes, functionality or operational characteristics documented in this report will be communicated to the body responsible for approving (certifying) the subject equipment. Thi Phan Printed name of official Signature of official 4700 Falls of Neuse Road, Suite 340 Raleigh, NC 27609 USA 30 November 2011 Address Date 919-855-1060 [email protected] Telephone number Email address of official

TUV Rheinland 762 Park Ave., Youngsville, NC 27596 FCC ID: YJ4CMGYZCDCZ31 Tel: (919) 554-3668, Fax: (919) 554-3542 Report Number: Supplement to 31151351.001 - External Photos Page 1 of 3 EUT: Zigbee Transmitter/Receiver Model: Limited Modular Device External Photos EUT Name: Zigbee Transmitter/Receiver EUT Model: Limited Modular Device FCC ID: YJ4CMGYZCDCZ31 FCC Title 47, Part 15, SubpartC, RSS-210 Issue 8, ANSI C63.4:2009 Prepared for: Thi Phan Consert, Inc. 4700 Falls of Neuse Road, Suite 340 Raleigh, NC 27609 USA Tel: 919-855-1060 Fax: 919-606-8978 Prepared by: TUV Rheinland of North America 762 Park Avenue Youngsville, NC 27596 Tel: (919) 554-3668 Fax: (919) 554-3542 http://www.tuv.com/ Report/Issue Date: 30 November 2011 Report Number: Supplement to 31151351.001 - External Photos TUV Rheinland 762 Park Ave., Youngsville, NC 27596 FCC ID: YJ4CMGYZCDCZ31 Tel: (919) 554-3668, Fax: (919) 554-3542 Report Number: Supplement to 31151351.001 - External Photos Page 2 of 3 EUT: Zigbee Transmitter/Receiver Model: Limited Modular Device External Photos: Figure 1: View of Device Controller used as the Test bed for the Zigbee tests TUV Rheinland 762 Park Ave., Youngsville, NC 27596 FCC ID: YJ4CMGYZCDCZ31 Tel: (919) 554-3668, Fax: (919) 554-3542 Report Number: Supplement to 31151351.001 - External Photos Page 3 of 3 EUT: Zigbee Transmitter/Receiver Model: Limited Modular Device Figure 2: View of Controller Device with the EUT Zigbee Modular Device

The Zigbee Limited Modular Device Label The circuit for the transmitter part is smaller than a palm, so per KDB # 784748 D01: "If the device is unquestionably too small for the FCC ID to be readable (smaller than 4-6 points), the FCC ID may be placed in the user manual." The Module FCC ID is placed on Page #16 of Device Controller Installation Guide EHWVN0114-01 and Device Controller Data Sheet (Rev B) EMKUT0115-02. The outside of the device into which the module is installed is displayed a label referring to the enclosed module. This exterior label can use wording as the following: “Contains Zigbee FCC ID: YJ4CMGYZCDCZ31””

Product Labels: Figure 1: View of Label for a “Device Controller” using the Limited Modular Device. Figure 2: View of another configuration of a Device Controller, using the Limited Modular Device. Label Location: Figure 3: Label Location as see on a Device Controller without relay Figure 4: Label Location as see on a Device Controller with relay

TUV Rheinland 762 Park Ave., Youngsville, NC 27596 FCC ID: YJ4CMGYZCDCZ31 Tel: (919) 554-3668, Fax: (919) 554-3542 Report Number: Supplement to 31151351.001 Rev A - Internal Photos Page 1 of 6 EUT: Zigbee Transmitter/Receiver Model: Limited Modular Device Internal Photos EUT Name: Zigbee Transmitter/Receiver EUT Model: Limited Modular Device FCC ID: YJ4CMGYZCDCZ31 FCC Title 47, Part 15, SubpartC, RSS-210 Issue 8, ANSI C63.4:2009 Prepared for: Thi Phan Consert, Inc. 4700 Falls of Neuse Road, Suite 340 Raleigh, NC 27609 USA Tel: 919-855-1060 Fax: 919-606-8978 Prepared by: TUV Rheinland of North America 762 Park Avenue Youngsville, NC 27596 Tel: (919) 554-3668 Fax: (919) 554-3542 http://www.tuv.com/ Report/Issue Date: 6 December 2011 Report Number: Supplement to 31151351.001 Rev A - Internal Photos TUV Rheinland 762 Park Ave., Youngsville, NC 27596 FCC ID: YJ4CMGYZCDCZ31 Tel: (919) 554-3668, Fax: (919) 554-3542 Report Number: Supplement to 31151351.001 Rev A - Internal Photos Page 2 of 6 EUT: Zigbee Transmitter/Receiver Model: Limited Modular Device Internal Photos: Figure 1: Top View of PCB. TUV Rheinland 762 Park Ave., Youngsville, NC 27596 FCC ID: YJ4CMGYZCDCZ31 Tel: (919) 554-3668, Fax: (919) 554-3542 Report Number: Supplement to 31151351.001 Rev A - Internal Photos Page 3 of 6 EUT: Zigbee Transmitter/Receiver Model: Limited Modular Device Figure 2: Top View of PCB. TUV Rheinland 762 Park Ave., Youngsville, NC 27596 FCC ID: YJ4CMGYZCDCZ31 Tel: (919) 554-3668, Fax: (919) 554-3542 Report Number: Supplement to 31151351.001 Rev A - Internal Photos Page 4 of 6 EUT: Zigbee Transmitter/Receiver Model: Limited Modular Device Figure 3: Top View with shield on. Antenna TUV Rheinland 762 Park Ave., Youngsville, NC 27596 FCC ID: YJ4CMGYZCDCZ31 Tel: (919) 554-3668, Fax: (919) 554-3542 Report Number: Supplement to 31151351.001 Rev A - Internal Photos Page 5 of 6 EUT: Zigbee Transmitter/Receiver Model: Limited Modular Device Figure 4: Top view with Shield off. Antenna TUV Rheinland 762 Park Ave., Youngsville, NC 27596 FCC ID: YJ4CMGYZCDCZ31 Tel: (919) 554-3668, Fax: (919) 554-3542 Report Number: Supplement to 31151351.001 Rev A - Internal Photos Page 6 of 6 EUT: Zigbee Transmitter/Receiver Model: Limited Modular Device Figure 5: Bottom View of Board.

FCCID: YJ4CMGYZCDCZ31 Report No.: 31151351.001 Revision B Page 1 of 68 The test results contained in this report refer exclusively to the product(s) presented for testing. No liability may be assumed for models or products not referred to herein. This test report may not be published or duplicated in part without permission of the testing body. This test report by itself does not constitute authorization for the use of any TUV Rheinland test mark. The report must not be used by the client to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the Federal Government. TUV Rheinland of North America, Inc., 762 Park Avenue, Youngsville, NC 27596-9470, Tel: 919-554-3668, Fax: 919-554-3542 QF09B040 Revision 0 Electromagnetic Compatibility Test Report Prepared in accordance with FCC Part 15C, RSS-210 Issue 8 On ZIGBEE – TRANSMITTER/RECEIVER Limited Modular Device Consert, Inc. 4700 Falls of Neuse Road, Suite 340 Raleigh, NC 27609 USA Prepared by: TUV Rheinland of North America, Inc. FCCID: YJ4CMGYZCDCZ31 Report No.: 31151351.001 Revision B Page 2 of 68 The test results contained in this report refer exclusively to the product(s) presented for testing. No liability may be assumed for models or products not referred to herein. This test report may not be published or duplicated in part without permission of the testing body. This test report by itself does not constitute authorization for the use of any TUV Rheinland test mark. The report must not be used by the client to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the Federal Government. TUV Rheinland of North America, Inc., 762 Park Avenue, Youngsville, NC 27596-9470, Tel: 919-554-3668, Fax: 919-554-3542 QF09B040 Revision 0 Manufacturer’s statement - attestation The manufacturer; Consert, Incorporated, as the responsible party for the equipment tested, hereby affirms: a) That he has reviewed and concurs that the test shown in this report are reflective of the operational characteristics of the device for which certification is sought; b) That the device in this test report will be representative of production units; c) That all changes (in hardware and software/firmware) to the subject device will be reviewed. d) That any changes impacting the attributes, functionality or operational characteristics documented in this report will be communicated to the body responsible for approving (certifying) the subject equipment. Thi Phan Printed name of official Signature of official 4700 Falls of Neuse Road, Suite 340 Raleigh, NC 27609 USA 30 November 2011 Address Date 919-855-1060 [email protected] Telephone number Email address of official FCCID: YJ4CMGYZCDCZ31 Report No.: 31151351.001 Revision B Page 3 of 68 The test results contained in this report refer exclusively to the product(s) presented for testing. No liability may be assumed for models or products not referred to herein. This test report may not be published or duplicated in part without permission of the testing body. This test report by itself does not constitute authorization for the use of any TUV Rheinland test mark. The report must not be used by the client to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the Federal Government. TUV Rheinland of North America, Inc., 762 Park Avenue, Youngsville, NC 27596-9470, Tel: 919-554-3668, Fax: 919-554-3542 QF09B040 Revision 0 Client: 4700 Falls of Neuse Road, Suite 340 Raleigh, NC 27609 USA Thi Phan 919-855-1060 [email protected] Identification: ZIGBEE - transmitter/receiver Serial No.: 000FAF Test item: Limited Modular Device Date tested: 7 July 2011 Testing location: TUV Rheinland of North America 762 Park Avenue Youngsville, NC 27596-9470 U.S.A. Tel: (919) 554-3668 Fax: (919) 554-3542 Test specification: Emissions: FCC Part 15, Subpart C, RSS-210 Issue 8: FCC Part 15.207(a) and RSS-GEN FCC Parts 15.247(d), 15.205, 15.209, 15.215(c) and RSS-210 A8.5 and RSS-GEN 7.2.1 FCC Part 15.247(a)(2) and RSS-210 A1.1.3, FCC Part 15.247 and RSS-210 Annex 8, FCC Part 15.247(b)(3) and RSS-210 A8.4(4), FCC Part 15.247(d) and RSS-210 2.2, FCC Parts 15.109(a) and RSS-GEN, FCC Part 15.107(b) and RSS-GEN FCC Parts 15.247(i) and RSS-102, Issue 4, Test Result The above product was found to be Compliant to the above test standard(s) tested by: Mark Ryan reviewed by: Michael Moranha 6 December 2010 Signature 12 December 2011 Signature Other Aspects: None Abbreviations: OK, Pass, Compliant, Complies = passed Fail, Not Compliant, Does Not Comply = failed N/A = not applicable Industry Canada 90552 and 100881 NVLAP Lab Code (200094-0) IC-2932H FCCID: YJ4CMGYZCDCZ31 Report No.: 31151351.001 Revision B Page 4 of 68 The test results contained in this report refer exclusively to the product(s) presented for testing. No liability may be assumed for models or products not referred to herein. This test report may not be published or duplicated in part without permission of the testing body. This test report by itself does not constitute authorization for the use of any TUV Rheinland test mark. The report must not be used by the client to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the Federal Government. TUV Rheinland of North America, Inc., 762 Park Avenue, Youngsville, NC 27596-9470, Tel: 919-554-3668, Fax: 919-554-3542 QF09B040 Revision 0 TABLE OF CONTENTS 1 GENERAL INFORMATION ......................................................................................................................... 5 1.1 S COPE ......................................................................................................................................................... 5 1.2 P URPOSE ..................................................................................................................................................... 5 1.3 S UMMARY OF TEST RESULTS ...............................................................…

Text truncated - open the document above for the full version.

FCCID: YJ4CMGYZCDCZ31 Report No.: 31151351.001 Revision B Page 1 of 68 The test results contained in this report refer exclusively to the product(s) presented for testing. No liability may be assumed for models or products not referred to herein. This test report may not be published or duplicated in part without permission of the testing body. This test report by itself does not constitute authorization for the use of any TUV Rheinland test mark. The report must not be used by the client to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the Federal Government. TUV Rheinland of North America, Inc., 762 Park Avenue, Youngsville, NC 27596-9470, Tel: 919-554-3668, Fax: 919-554-3542 QF09B040 Revision 0 Electromagnetic Compatibility Test Report Prepared in accordance with FCC Part 15C, RSS-210 Issue 8 On ZIGBEE – TRANSMITTER/RECEIVER Limited Modular Device Consert, Inc. 4700 Falls of Neuse Road, Suite 340 Raleigh, NC 27609 USA Prepared by: TUV Rheinland of North America, Inc. FCCID: YJ4CMGYZCDCZ31 Report No.: 31151351.001 Revision B Page 2 of 68 The test results contained in this report refer exclusively to the product(s) presented for testing. No liability may be assumed for models or products not referred to herein. This test report may not be published or duplicated in part without permission of the testing body. This test report by itself does not constitute authorization for the use of any TUV Rheinland test mark. The report must not be used by the client to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the Federal Government. TUV Rheinland of North America, Inc., 762 Park Avenue, Youngsville, NC 27596-9470, Tel: 919-554-3668, Fax: 919-554-3542 QF09B040 Revision 0 Manufacturer’s statement - attestation The manufacturer; Consert, Incorporated, as the responsible party for the equipment tested, hereby affirms: a) That he has reviewed and concurs that the test shown in this report are reflective of the operational characteristics of the device for which certification is sought; b) That the device in this test report will be representative of production units; c) That all changes (in hardware and software/firmware) to the subject device will be reviewed. d) That any changes impacting the attributes, functionality or operational characteristics documented in this report will be communicated to the body responsible for approving (certifying) the subject equipment. Thi Phan Printed name of official Signature of official 4700 Falls of Neuse Road, Suite 340 Raleigh, NC 27609 USA 30 November 2011 Address Date 919-855-1060 [email protected] Telephone number Email address of official FCCID: YJ4CMGYZCDCZ31 Report No.: 31151351.001 Revision B Page 3 of 68 The test results contained in this report refer exclusively to the product(s) presented for testing. No liability may be assumed for models or products not referred to herein. This test report may not be published or duplicated in part without permission of the testing body. This test report by itself does not constitute authorization for the use of any TUV Rheinland test mark. The report must not be used by the client to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the Federal Government. TUV Rheinland of North America, Inc., 762 Park Avenue, Youngsville, NC 27596-9470, Tel: 919-554-3668, Fax: 919-554-3542 QF09B040 Revision 0 Client: 4700 Falls of Neuse Road, Suite 340 Raleigh, NC 27609 USA Thi Phan 919-855-1060 [email protected] Identification: ZIGBEE - transmitter/receiver Serial No.: 000FAF Test item: Limited Modular Device Date tested: 7 July 2011 Testing location: TUV Rheinland of North America 762 Park Avenue Youngsville, NC 27596-9470 U.S.A. Tel: (919) 554-3668 Fax: (919) 554-3542 Test specification: Emissions: FCC Part 15, Subpart C, RSS-210 Issue 8: FCC Part 15.207(a) and RSS-GEN FCC Parts 15.247(d), 15.205, 15.209, 15.215(c) and RSS-210 A8.5 and RSS-GEN 7.2.1 FCC Part 15.247(a)(2) and RSS-210 A1.1.3, FCC Part 15.247 and RSS-210 Annex 8, FCC Part 15.247(b)(3) and RSS-210 A8.4(4), FCC Part 15.247(d) and RSS-210 2.2, FCC Parts 15.109(a) and RSS-GEN, FCC Part 15.107(b) and RSS-GEN FCC Parts 15.247(i) and RSS-102, Issue 4, Test Result The above product was found to be Compliant to the above test standard(s) tested by: Mark Ryan reviewed by: Michael Moranha 6 December 2010 Signature 12 December 2011 Signature Other Aspects: None Abbreviations: OK, Pass, Compliant, Complies = passed Fail, Not Compliant, Does Not Comply = failed N/A = not applicable Industry Canada 90552 and 100881 NVLAP Lab Code (200094-0) IC-2932H FCCID: YJ4CMGYZCDCZ31 Report No.: 31151351.001 Revision B Page 4 of 68 The test results contained in this report refer exclusively to the product(s) presented for testing. No liability may be assumed for models or products not referred to herein. This test report may not be published or duplicated in part without permission of the testing body. This test report by itself does not constitute authorization for the use of any TUV Rheinland test mark. The report must not be used by the client to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the Federal Government. TUV Rheinland of North America, Inc., 762 Park Avenue, Youngsville, NC 27596-9470, Tel: 919-554-3668, Fax: 919-554-3542 QF09B040 Revision 0 TABLE OF CONTENTS 1 GENERAL INFORMATION ......................................................................................................................... 5 1.1 S COPE ......................................................................................................................................................... 5 1.2 P URPOSE ..................................................................................................................................................... 5 1.3 S UMMARY OF TEST RESULTS ...............................................................…

Text truncated - open the document above for the full version.

TUV Rheinland 762 Park Ave., Youngsville, NC 27596 FCC ID: YJ4CMGYZCDCZ31 Tel: (919) 554-3668, Fax: (919) 554-3542 Report Number: Supplement to 31151351.001 - Test Setup Photos Page 1 of 13 EUT: Zigbee Transmitter/Receiver Model: Limited Modular Device Test Setup Photos EUT Name: Zigbee Transmitter/Receiver EUT Model: Limited Modular Device FCC ID: YJ4CMGYZCDCZ31 FCC Title 47, Part 15, SubpartC, RSS-210 Issue 8, ANSI C63.4:2009 Prepared for: Thi Phan Consert, Inc. 4700 Falls of Neuse Road, Suite 340 Raleigh, NC 27609 USA Tel: 919-855-1060 Fax: 919-606-8978 Prepared by: TUV Rheinland of North America 762 Park Avenue Youngsville, NC 27596 Tel: (919) 554-3668 Fax: (919…

Text truncated - open the document above for the full version.