YKH-B5000ZBBarcode Scanner

Symbologies setting - Enable - Disable How do you program your scanner? 1.Scan Start Configuration 2.Scan all necessary able for parameters that Meet your application 3.Scan end configuration to save the changes. Resetting The Standard Product Defaults If you aren’t sure what programming options are in your scanner, or you’ve changed some options and want the factory settings restored, scan the bar code below. End Confi guration I nterface selection Reading mode Language .........etc. Start Confi guration Standard Product Default Setting WIRELESS BARCODE SCANNER Quick Start Guide KC-5200ZB FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -Reorient or relocate the receiving antenna. -Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/ TV technician for help. CAUTION: Any changes or modifications not expressly approved by the grantee of this device could void the user's authority to operate the equipment. Labeling requirements This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. RF exposure warning The equipment complies with FCC RF exposure limits set forth for an uncontrolled environment.The equipment must not be co-located or operating in conjunction with any other antenna or transmitter. Before Getting Started About your wireless scanner Note: New batteries should be fully charged before their first use USB docking station USB Receiver USB recharge cableStrap Wireless Scanner It is one on one wireless data communication protocol. The scanner is already paired with the USB receiver. Just easily plug USB receiver and start the operation. The scanner on a real time basis, if the scanner is connected, the barcode is decoded and transmitted to the remote host without any delay. If the scanner is not connected or out of range, the data is lost (status: 2 beeps/4 beeps). Wake up your wireless scanner Press and release the trigger on your scanner to activate it. Your scanner is ready to work when orange LED comes on. Connect USB receiver to a host computer The device can be quickly recognized by host computer without any software/driver installation. Within less than 10 seconds the receiver will flash red to inform the Initialization is completed. Recharging the battery The Red LED comes on when the battery level is low, please recharge the scanner immediately. When the scanner is charging, the LED is green (solid). A full recharge (from completely drained battery) takes approximately 4 hours. When the scanner is fully charged, the green LED will go off. How to pair (repair) you scanner and receiver? Step 1: Plug the USB receiver to the scanner Step 2: Trigger the button on the scanner. Step 3: Devices are successful paired with 1 beep from scanner and 1 blink from the USB receiver. Scanner LED indicator USB receiver LED indicator Status / indicator Good Scan Transmission Trasmission failure (in memory mode) failure Low battery Recharge Operation mode Sleeping BeeperBlue LEDGreen LEDRed LEDOrange LED 1 beep 4 beeps 2 beeps 4 blink 2 blink None 1 blink None On None On None On None Color Red Indication *High <Buzzer> Off Low <Vibration motor> Enable *Disable <Memory mode> Enable *Disable *10min <Sleep mode> 30min always on Default setting of wireless scanner Buzzer : High Vibrator: Disable Memory mode: Disable Power saving (sleep mode): 10min The default values can be modified by scanning the following options. Note: Please scan the following barcode directly with your USB receiver on. No need to scan start and end configuration barcodes. HID USB Keyboard Country Scan the appropriate country code below to program the keyboard for your country. As a general rule, the following characters are supported, but need special care for countries other than the United States: @ | $ # { } [ ] = / ‘ \ < > ~ Note: Please scan the following barcode directly with your USB receiver on. No need to scan start and end configuration barcodes. Terminator selection US Italian Spanish German Danish Japanese French Turkey

Report No.: 14B0492R-RFUSP26V00 Page : 1 of 22

Attachment 2 : EUT Detailed Photographs (1) EUT Photo (2) EUT Photo Report No.: 14B0492R-RFUSP26V00 Page : 2 of 22

(3) EUT Photo (4) EUT Photo Report No.: 14B0492R-RFUSP26V00 Page : 3 of 22

(5) EUT Photo

NUMA Electronics Inc. FCC ID.: YKH-B5000ZB 7F-8, No.107, Sec. 1 Zhongshan Rd. Xinzhuang Taiwan Tel : 886-2-8522-8350 Ext.:10 FCC ID Label

NUMA Electronics Inc. FCC ID.: YKH-B5000ZB 7F-8, No.107, Sec. 1 Zhongshan Rd. Xinzhuang Taiwan Tel : 886-2-8522-8350 Ext.:10 The FCC ID Label will be placed on the equipment as shown in the photograph below.

Report No.: 14B0492R-RFUSP26V00 Page : 4 of 22

(6) EUT Photo (7) EUT Photo Report No.: 14B0492R-RFUSP26V00 Page : 5 of 22

(8) EUT Photo (9) EUT Photo Report No.: 14B0492R-RFUSP26V00 Page : 6 of 22

(10) EUT Photo (11) EUT Photo Report No.: 14B0492R-RFUSP26V00 Page : 7 of 22

(12) EUT Photo (13) EUT Photo Report No.: 14B0492R-RFUSP26V00 Page : 8 of 22

(14) EUT Photo (15) EUT Photo Report No.: 14B0492R-RFUSP26V00 Page : 9 of 22

(16) EUT Photo (17) EUT Photo Report No.: 14B0492R-RFUSP26V00 Page : 10 of 22

(18) EUT Photo (19) EUT Photo Report No.: 14B0492R-RFUSP26V00 Page : 11 of 22

(20) EUT Photo (21) EUT Photo Report No.: 14B0492R-RFUSP26V00 Page : 12 of 22

(22) EUT Photo (23) EUT Photo Report No.: 14B0492R-RFUSP26V00 Page : 13 of 22

(24) EUT Photo (25) EUT Photo Report No.: 14B0492R-RFUSP26V00 Page : 14 of 22

(26) EUT Photo (27) EUT Photo Antenna Report No.: 14B0492R-RFUSP26V00 Page : 15 of 22

(28) EUT Photo (29) EUT Photo Report No.: 14B0492R-RFUSP26V00 Page : 16 of 22

(30) EUT Photo (31) EUT Photo (BC-5200ZB) Report No.: 14B0492R-RFUSP26V00 Page : 17 of 22

(32) EUT Photo (BC-5200ZB) (33) EUT Photo (BC-5200ZB) Report No.: 14B0492R-RFUSP26V00 Page : 18 of 22

(34) EUT Photo (BC-5200ZB) (35) EUT Photo (BD-5200ZB) Report No.: 14B0492R-RFUSP26V00 Page : 19 of 22

(36) EUT Photo (BD-5200ZB) (37) EUT Photo (BD-5200ZB) Report No.: 14B0492R-RFUSP26V00 Page : 20 of 22

(38) EUT Photo (BD-5200ZB) (39) EUT Photo (BL-5200ZB) Report No.: 14B0492R-RFUSP26V00 Page : 21 of 22

(40) EUT Photo (BL-5200ZB) (41) EUT Photo (BL-5200ZB) Report No.: 14B0492R-RFUSP26V00 Page : 22 of 22

(42) EUT Photo

RF Exposure Statement 1. Standard Applicable According to 1.1307 (b)(1), systems operating under the provisions of this section shall be operated in a manner that ensure that the public is not exposed to radio frequency energy level in excess of the Commission’s guideline. 2. Measurement Result: According to KDB 447498 D01 Mobile Portable RF Exposure v05, Operation frequency = 2450MHz and antenna separation distance = 5mm, SAR Test Exclusion Threshold = 10mW The Device max peak output power = 9.63dBm, Equivalent to 9.18mW and less than 10mW The SAR/MPE measurement is not necessary.

Report No. 14B0492R-RFUSP26V00 Page: 1 of 43 FCC Test Report Product Name Barcode Scanner Model No. BD-5200ZB, BC-5200ZB, BL-5200ZB FCC ID. YKH-B5000ZB Applicant NUMA Electronics Inc. Address 7F-8, No.107, Sec. 1 Zhongshan Rd. Xinzhuang Taiwan Date of Receipt Nov. 20, 2014 Issued Date Feb. 03, 2015 Report No. 14B0492R-RFUSP26V00 Report Version V1.0 The test results relate only to the samples tested. The test results shown in the test report are traceable to the national/international standard through the calibration of the equipment and evaluated measurement uncertainty herein. This report must not be used to claim product endorsement by TAF or any agency of the government. The test report shall not be reproduced without the written approval of QuieTek Corporation. Report No. 14B0492R-RFUSP26V00 Page: 2 of 43 Test Report Issued Date: Feb. 03, 2015 Report No.: 14B0492R-RFUSP26V00 Product Name Barcode Scanner Applicant NUMA Electronics Inc. Address 7F-8, No.107, Sec. 1 Zhongshan Rd. Xinzhuang Taiwan Manufacturer NUMA Electronics Inc. Model No. BD-5200ZB, BC-5200ZB, BL-5200ZB FCC ID. YKH-B5000ZB EUT Rated Voltage DC 3.7V (Power by Battery) EUT Test Voltage DC 3.7V (Power by Battery) Trade Name NUMA Applicable Standard FCC CFR Title 47 Part 15 Subpart C: 2013 ANSI C63.10: 2013, KDB 558074 D01 DTS Meas Guidance v03r02 Test Result Complied Documented By : ( Senior Adm. Specialist / Jinn Chen ) Tested By : ( Assistant Engineer / Nova Chu ) Approved By : ( Director / Vincent Lin ) Report No. 14B0492R-RFUSP26V00 Page: 3 of 43 TABLE OF CONTENTS Description Page 1. GENERAL INFORMATION ............................................................................................................... 4 1.1. EUT Description .................................................................................................................................. 4 1.2. Operational Description ....................................................................................................................... 6 1.3. Tested System Details .......................................................................................................................... 7 1.4. Configuration of Tested System ........................................................................................................... 7 1.5. EUT Exercise Software ........................................................................................................................ 8 1.6. Test Facility ......................................................................................................................................... 9 2. CONDUCTED EMISSION ................................................................................................................ 10 2.1. Test Equipment .................................................................................................................................. 10 2.2. Test Setup........................................................................................................................................... 10 2.3. Limits .................................................................................................................................................. 11 2.4. Test Procedure ..................................................................................................................................... 11 2.5. Uncertainty ......................................................................................................................................... 11 2.6. Test Result of Conducted Emission .................................................................................................... 12 3. PEAK POWER OUTPUT .................................................................................................................. 14 3.1. Test Equipment .................................................................................................................................. 14 3.2. Test Setup........................................................................................................................................... 14 3.3. Limit ................................................................................................................................................. 14 3.4. Test Procedure .................................................................................................................................... 14 3.5. Uncertainty ........................................................................................................................................ 14 3.6. Test Result of Peak Power Output ...................................................................................................... 15 4. RADIATED EMISSION ..................................................................................................................... 16 4.1. Test Equipment .................................................................................................................................. 16 4.2. Test Setup........................................................................................................................................... 16 4.3. Limits ................................................................................................................................................. 17 4.4. Test Procedure .................................................................................................................................... 19 4.5. Uncertainty ........................................................................................................................................ 19 4.6. Test Result of Radiated Emission ....................................................................................................... 20 5. RF ANTENNA CONDUCTED TEST ................................................................................................ 24 5.1. Test Equipment .............…

Text truncated - open the document above for the full version.

Report No.: 14B0492R-RFUSP26V00 Page : 1 of 3 Attachment 1: EUT Test Setup Photographs Front View of Radiated Test Back View of Radiated Test Report No.: 14B0492R-RFUSP26V00 Page : 2 of 3 Front View of Radiated Test (Horn) Back View of Radiated Test (Horn) Report No.: 14B0492R-RFUSP26V00 Page : 3 of 3 Front View of Radiated Test (Horn) Back View of Radiated Test (Horn)