YKH319-BT10200Bluetooth Headset

BT-102 Programming User Guide version 1.0 · - 1- Revision history Version date Record author 1.0 2020/06/01 initial version G AT T · - 2- FCC : FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -Reorient or relocate the receiving antenna. -Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/ TV technician for help. CAUTION: Any changes or modifications not expressly approved by the grantee of this device could void the user's authority to operate the equipment. This module is intended for OEM integrator. The OEM integrator is responsible for the compliance to all the rules that apply to the product into which this certified RF module is integrated. Additional testing and certification may be necessary when multiple modules are used. USERS MANUAL OF THE END PRODUCT In the users manual of the end product, the end user has to be informed to keep at least 20 cm separation with the antenna while this end product is installed and operated. The end user has to be informed that the FCC radio-frequency exposure guidelines for an uncontrolled environment can be satisfied. The end user has to also be informed that any changes or modifications not expressly approved by the manufacturer could void the user's authority to operate this equipment. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation. · - 3- NCC 警語 取得審驗證明之低功率射頻器材，非經核准，公司、商號或使用者均不得擅自變更頻率、加大功率或變更 原設計之特性及功能。低功率射頻器材之使用不得影響飛航安全及干擾合法通信；經發現有干擾現象時， 應立即停用，並改善至無干擾時方得繼續使用。前述合法通信，指依電信管理法規定作業之無線電通信。 低功率射頻器材須忍受合法通信或工業、科學及醫療用電波輻射性電機設備之干擾。本模組於取得認證後 將依規定於模組本體標示審驗合格標籤，並要求最終產品平台廠商(OEM Integrator)於最終產品平台(End Product)上標示:本產品內含射頻模組，其 NCC 型式認證號碼為: CCAH23Y10110T0 LABEL OF THE END PRODUCT The final end product must be labeled in a visible area with the following Contains FCC ID: YKH319-BT10200 This radio transmitter FCC ID: YKH319-BT10200 has been approved by FCC to operate with the antenna types listed below with the maximum permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device. Table of contents Table of contents 1. Introduction ........................................................................................................................................................................6 Overview ............................................................................................................................................................................. 6 2. Instruction description ..................................................................................................................................................6 3. List of general basic instructions ............................................................................................................................ 7 3.1 Test command AT ........................................................................................................................................................ 7 3.2 Query the version number command AT+VER ........................................................................................................7 3.3 Read Bluetooth MAC address ..................................................................................................................................7 3.3.1 Read BLE MAC address AT+LEADDR ..............................................................................................................7 3.3.2 Read BR/EDR MAC address AT+ADDR ............................................................................................................7 3.4 Query/modify Bluetooth name ................................................................................................................................ 7 3.4.1 Query BR/EDR MAC Bluetooth name AT+NAME ............................................................................................7 3.4.2 Modify BR/EDR Bluetooth name AT+NAME=Param1,Param2 ......................................................................8 3.3.3 Query BLE bluetooth name AT+LENAME ......................................................................................................8 3.3.4 Modify BLE bluetooth name AT+LENAME=Param1,Param2 ........................................................................8 3.4 Query/modify PIN code ............................................................................................................................................ 8 3.4.1 Query PIN code AT+PIN ...............................................................................................................................8 3.4.2 Modify PIN code AT+PIN=Param ..................................................................................................................9 3.5 Easy pairing setup ..............…

Text truncated - open the document above for the full version.

U.S. Agent Designation for Service of Process ATTENTION: Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA REGARDING: FCC Certification – Section 2.911(d)(7) Information Designated U.S. Agent Company Name: Approve-IT, Inc. Contact Name: Nathan Grinager Street Address: 8011 34 th Ave South, Suite 342 City/Province/Zip: Bloomington, MN 55425 Telephone No: 651-247-1678 Email: [email protected] FRN #: 0027533835 This letter is to confirm that we (“the Designated U.S. Agent) have accepted the responsibility to act as the Designated U.S. Agent for Service of Process as required by section 47 CFR 2.911(d)(7) on behalf of the Applicant noted below. U.S. Agent Signature: Date: Signed by (Printed Name/Title): Nathan Grinager / Co-President *This letter must be dated within 1-year (update if other terms apply) of the date the application is submitted to the TCB for device certification The Applicant confirms its explicit consent and acknowledges that they must maintain an agent for no less than one year after terminating all marketing and importation OR the conclusion of any Commission-related proceeding involving the equipment. The applicant further acknowledges their responsibility to inform the FCC whenever the Designated U.S. Agent information above changes. Applicant Company name: NUMA Electronics Inc. Grantee Code: YKH Contact Name: Gary Chen Street Address: 3F, No. 5, Wugong 5th Rd., Xinzhuang Dist. City/Province/Zip: New Taipei City 24890 April 26, 2023 Telephone No: 886-2-8990-1579 Email: [email protected] Applicant Signature: Date: A pril 26, 2023 Signed by (Printed Name/Title): Gary Chen/ Manager

Rev 1/26/2023 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Date: February 22, 2023 Ref: Attestation Statements Part 2.911(d)(5)(ii) Filing FCC ID: YKH319-BT10200 NUMA Electronics Inc. (“the applicant”) certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List as an entity producing “covered” equipment. Sincerely, ------------------------------------------------------ Gary Chen / Manager NUMA Electronics Inc.

Rev 1/26/2023 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Date: February 22, 2023 Ref: Attestation Statements Part 2.911(d)(5)(i) Filing FCC ID: YKH319-BT10200 NUMA Electronics Inc. (“the applicant”) certifies that the equipment for which authorization is sought is not “covered” equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. Sincerely, ------------------------------------------------------ Gary Chen / Manager NUMA Electronics Inc.

Modular Approval Request FCC (KDB 996369 D01 & Part 15.212) FCC ID: YKH319-BT10200 Items to be covered by Single modular transmitters. Answer from applicant 1. The radio elements must have the radio frequency circuitry shielded. Physical components and tuning capacitor(s) may be located external to the shield, but must be on the module assembly. Yes. 2. The module must have buffered modulation/data inputs to ensure that the device will comply with Part 15 requirements with any type of input signal. Yes. 3. The module must contain power supply regulation on the module Yes,the module has its own power supply regulation. 4. The module must contain a permanently attached antenna, or contain a unique antenna connector, and be marketed and operated only with specific antenna(s), per §§ 15.203, 15.204(b), 15.204(c), 15.212(a), 2.929(b). Yes.,it is PIFA antenna 5. The module must demonstrate compliance in a stand-alone configuration. Yes. 6. The module must be labeled with its permanently affixed FCC ID label, or use an electronic display (see KDB Publication 784748). Yes,the module has a permanently affixed lable with its own FCC ID number.Please refer to lable and lable location 7. The module must comply with all specific rules applicable to the transmitter, including all the conditions provided in the integration instructions by the grantee. Yes.,the module comply with this requirement.Please refer to user manual. 8. The module must comply with RF exposure requirements. Yes. The module comply with this requirement.Module transmitter final configuration comply with FCC RF Exposure. Items to be covered by Split modular transmitters. Answer from applicant 1. The modular transmitter must comply with all requirements of a single modular transmitter except for items (1) & (5) of the above single modular approval requirements. N/A 2. Only the radio front end must be shielded. The physical crystal and tuning capacitors may be located external to the shielded radio elements. The interface between the split sections of the modular system must be digital with a minimum signalling amplitude of 150 mV peak-to-peak. N/A 3. Control information and other data may be exchanged between the transmitter control elements and radio front end. N/A 4. The sections of a split modular transmitter must be tested installed in a host device(s) similar to that which is representative of the platform(s) intended for use. N/A 5. Manufacturers must ensure that only transmitter control elements and radio front end components that have been approved together are capable of operating together. The transmitter module must not operate unless it has verified that the installed transmitter control elements and radio front end have been authorized together. Manufacturers may use means including, but not limited to, coding in hardware and electronic signatures in software to meet these requirements, and must describe the methods in their application for equipment authorization. N/A Note: A limited modular approval (LMA) may be granted for single or split modular transmitters that comply partially with the requirements above. Name and surname of applicant (or authorized representative): Gary Chen Date: 22 February 2023 Signature:

Declaration of Authorization We Name: NUMA Electronics Inc. Address: 3F, No. 5, Wugong 5th Rd., Xinzhuang Dist. City: New Taipei City 24890 Country: Taiwan Declare that: Name Representative of agent: Stanley Wu Agent Company name: DEKRA Testing and Certification Co., Ltd. Address: No. 26, Huaya 1 st Rd., Guishan Dist., City: Taoyuan City 33341, Country: Taiwan. is authorized to apply for FCC/JP certifications of the following product(s): Product Name: Bluetooth Module Model: BT-102 FCC ID: YKH319-BT10200 Trademark: NUMA on our behalf. Date: February 22, 2023 Name: Gary Chen Function: Manager Signature:

Date: November 22, 2022 To: Federal Communications Commission 7435 Oakland Mills Road Columbia, MD Confidentiality Request regarding application for certification of FCC ID: YKH319-BT10200 Pursuant to Sections 0.457 and 0.459 of the Commission’s Rules, the Applicant Hereby requests confidential treatment of information accompanying this Application As outlined below: Type of Confidentiality Requested Exhibit ☒ Permanent Block Diagrams ☒ Permanent Operation Description/Theory of Operation ☒ Permanent Schematics The above materials contain trade secrets and proprietary information not customarily Released to the public. The public disclosure of these matters might be harmful to the Applicant and provide unjustified benefits to its competitors. The Applicant understands that pursuant to Rule 0.457, disclosure of this Application and all accompanying documentation will not be made before the date of the Grant for this application. Pursuant to DA04-1705 June 15, 2004 of the Commission’s public notice, we also request temporary confidential treatment of information accompanying this application as outlined below: Type of Confidentiality Requested Exhibit ☒ Short Term External Photos ☒ Short Term Internal Photos ☒ Short Term Test Setup Photos ☒ Short Term User’s Manual Note: Release date of short term confidentiality is 180 days from grant date marked. (FCC must be informed when marketing begins earlier.) Sincerely, Name: Gary Chen Function: Manager Signature:

Report No: 22B0267R-NCC Product Photos Page: 1 of 3 (1) EUT Photo (2) EUT Photo Report No: 22B0267R-NCC Product Photos Page: 2 of 3 (3) EUT Photo (4) EUT Photo Report No: 22B0267R-NCC Product Photos Page: 3 of 3 (5) EUT Photo (6) EUT Photo

-------------------------------------------------------------------------------------------------------- Certification No.: FCC ID: YKH319-BT10200 The label sample is located on the top of the EUT Model:BT-102

Report No: 22B0267R-NCC Product Photos Page: 1 of 1 (1) EUT Photo (2) EUT Photo Antenna

Report No.: 22B0267R-RFUSV17S-A Page: 1 of 7 RF Exposure Report Product Name : Bluetooth Module Model No. : BT-102 FCC ID : YKH319-BT10200 Applicant : NUMA Electronics Inc. Address : 3F, No. 5, Wugong 5th Rd., Xinzhuang Dist New Taipei City Taiwan Date of Receipt : Nov. 07, 2022 Date of Declaration : Feb. 15, 2023 Report No. : 22B0267R-RFUSV17S-A Report Version : V1.0 The test results relate only to the samples tested. The test results shown in the test report are traceable to the national/international standard through the calibration report of the equipment and evaluated measurement uncertainty herein. This report must not be used to claim product endorsement by TAF or any agency of the government. The test report shall not be reproduced without the written approval of DEKRA Testing and Certification Co., Ltd. Measurement uncertainties evaluated for each testing system and associated connections are given here to provide the system information for reference. Compliance determinations do not take into account measurement uncertainties for each testing system, but are based on the results of the compliance measurement. Report No.: 22B0267R-RFUSV17S-A Page: 2 of 7 Product Name Bluetooth Module Applicant NUMA Electronics Inc. Address 3F, No. 5, Wugong 5th Rd., Xinzhuang Dist New Taipei City Taiwan Manufacturer NUMA Electronics Inc. Model No. BT-102 FCC ID YKH319-BT10200 Trade Name NUMA Applicable Standard KDB 447498 D01 v06 Minimum test separation distance ≥ 20 cm For low power devices Test Result Complied Documented By : ( Senior Project Specialist / Joanne Lin ) Tested By : ( Senior Engineer / Alan Chen ) Approved By : ( Manager / Tim Sung ) Report No.: 22B0267R-RFUSV17S-A Page: 3 of 7 Revision History Report No. Ve r s i o n Description Issued Date 22B0267R-RFUSV17S-A V1.0 Initial issue of report. Feb. 15, 2023 Report No.: 22B0267R-RFUSV17S-A Page: 4 of 7 1. General Information 1.1. EUT Description Product Name Bluetooth Module Trade Name NUMA Model No. BT-102 FCC ID YKH319-BT10200 Note: For more detailed information please refer to report No.: 22B0267R-RFUSBLEV01-A, 22B0267R-RFUSBT2V01-A. . Report No.: 22B0267R-RFUSV17S-A Page: 5 of 7 2. Test Facility USA : FCC Registration Number: TW0033 Canada : CAB Identifier Number: TW3023 / Company Number: 26930 Site Description : Accredited by TAF Accredited Number: 3023 Test Laboratory : DEKRA Testing and Certification Co., Ltd Address : No. 5-22, Ruishukeng Linkou District, New Taipei City, 24451, Taiwan Performed Location : No. 26, Huaya 1st Rd., Guishan Dist.,Taoyuan City 333411, Taiwan, R.O.C. Phone Number : +886-3-275-7255 Fax Number : +886-3-327-8031 Email Address : [email protected] Website : http://www.dekra.com.tw Report No.: 22B0267R-RFUSV17S-A Page: 6 of 7 3. RF Exposure Evaluation 3.1. Standard Applicable According to KDB 447498 D01 (7.1), A minimum test separation distance ≥ 20 cm is required between the antenna and radiating structures of the device and nearby persons to apply mobile device exposure limits. 3.2. Limits According to FCC 1.1310: The criteria listed in the following table shall be used to evaluate the environment impact of human exposure to radio frequency (RF) radiation as specified in 1.1307(b) LIMITS FOR MAXIMUM PERMISSIBLE EXPOSURE (MPE) Frequency Range (MHz) Electric Field Strength (V/m) Magnetic Field Strength (A/m) Power Density (mW/cm 2 ) Average Time (Minutes) (A) Limits for Occupational/ Control Exposures 300-1500 -- -- F/300 6 1500-100,000 -- -- 5 6 (B) Limits for General Population/ Uncontrolled Exposures 300-1500 -- -- F/1500 6 1500-100,000 -- -- 1 30 F= Frequency in MHz Friis Formula Friis transmission formula: Pd = (Pout*G)/(4*pi*r 2 ) Where Pd = power density in mW/cm 2 Pout = output power to antenna in mW G = gain of antenna in linear scale Pi = 3.1416 R = distance between observation point and center of the radiator in cm This equipment which can not transmit signals simultaneously. Report No.: 22B0267R-RFUSV17S-A Page: 7 of 7 3.3. Test Result of RF Exposure Evaluation Product : Bluetooth Module Test Item : RF Exposure Evaluation Band Frequency (MHz) Tune-up E.I.R.P (dBm) Tune-up E.I.R.P (mW) Power Density at R = 20 cm (mW/cm2) Limit (mW/cm2) Bluetooth 2441 5.690 3.707 0.0007 1 Bluetooth LE 2440 5.740 3.750 0.0007 1 Note: (1) The conducted output power is refer to report No.: 22B0267R-RFUSBLEV01-A, 22B0267R-RFUSBT2V01-A from the DEKRA. (2) Make sure the measured maximum output power within the including tune-up tolerance Bluetooth 2.39 dBm and Bluetooth LE 2.44 dBm.

DEKRA Testing and Certification No. 26, Huaya 1st Rd., Guishan Dist., Taoyuan City 333411 , Taiwan TEL: +886-3-725-7255 www.dekra-certification.com 2320661R-A324150030 Page 1 of 12 2023-04-25 Antenna Measurement Report Model: BT-102 Manufacturer: NUMA Electronics Inc. Antenna Type: PIFA Tested by (name / position & signature) Saul Wang / Engineer Approved by (name / position & signature) Lorien Chang / Manager Date of issue 2023/4/25 DEKRA Testing and Certification No. 26, Huaya 1st Rd., Guishan Dist., Taoyuan City 333411 , Taiwan TEL: +886-3-725-7255 www.dekra-certification.com 2320661R-A324150030 Page 2 of 12 2023-04-25 Index Competences and guarantees .......................................................................................................... 3 General conditions .............................................................................................................................. 3 Data provided by the client ................................................................................................................ 3 Testing period and place ................................................................................................................... 4 Document history ................................................................................................................................ 4 Environmental conditions .................................................................................................................. 4 Testing verdicts ................................................................................................................................... 4 Used Equipment ................................................................................................................................. 4 Appendix A: Test results .................................................................................................................... 5 DEKRA Testing and Certification No. 26, Huaya 1st Rd., Guishan Dist., Taoyuan City 333411 , Taiwan TEL: +886-3-725-7255 www.dekra-certification.com 2320661R-A324150030 Page 3 of 12 2023-04-25 Competences and guarantees DEKRA is a testing laboratory competent to carry out the tests described in this report. In order to assure the traceability to other national and international laboratories, DEKRA has a calibration and maintenance program for its measurement equipment. DEKRA guarantees the reliability of the data presented in this report, which is the result of the measurements and the tests performed to the item under test on the date and under the conditions stated in the report and it is based on the knowledge and technical facilities available at DEKRA at the time of performance of the test. DEKRA is liable to the client for the maintenance of the confidentiality of all information related to the item under test and the results of the test. The results presented in this Test Report apply only to the particular item under test established in this document. IMPORTANT: No parts of this report may be reproduced or quoted out of context, in any form or by any means, except in full, without the previous written permission of DEKRA Testing and Certification. General conditions 1.This report is only referred to the item that has undergone the test. 2.This report does not constitute or imply on its own an approval of the product by the Certification Bodies or competent Authorities. 3.This document is only valid if complete; no partial reproduction can be made without previous written permission of DEKRA Testing and Certification. 4.This test report cannot be used partially or in full for publicity and/or promotional purposes without previous written permission of DEKRA Testing and Certification. Data provided by the client The following data has been provided by the client: 1. No DEKRA Testing and Certification declines any responsibility with respect to the information provided by the client and that may affect the validity of results. DEKRA Testing and Certification No. 26, Huaya 1st Rd., Guishan Dist., Taoyuan City 333411 , Taiwan TEL: +886-3-725-7255 www.dekra-certification.com 2320661R-A324150030 Page 4 of 12 2023-04-25 Testing period and place Test Location DEKRA Testing and Certification No. 26, Huaya 1st Rd., Guishan Dist., Taoyuan City 333411 , Taiwan Date (start) 2022/11/22 Date (finish) 2022/11/23 Document history Report number Revision Date Description 22B0267R- A324310010S-A Rev. 1.0 2022/11/23 First release 22B0267R- A324310010S-A Rev. 2.0 2023/4/20 Update info 22B0267R- A324310010S-A Rev. 2.0 2023/4/25 Remove confidential Environmental conditions The climatic conditions during the tests are within the limits specified by the manufacturer for the operation of the EUT and the test equipment. The climatic conditions during the tests were within the following limits: Ambient temperature 22 °C – 28 °C Relative Humidity air < 60% Testing verdicts Not applicable: N/A Pass: P Fail: F Infomation: Info Not measured: N/M Used Equipment Name Manufacturer Type/Model Serial Number Calibration Last Cal. Vector Network Analyzer R&S ZNB 8 106333 2022/5/16 Measurement Software ETS-Lindgren EMQuest 1.14 1474 N/A DEKRA Testing and Certification No. 26, Huaya 1st Rd., Guishan Dist., Taoyuan City 333411 , Taiwan TEL: +886-3-725-7255 www.dekra-certification.com 2320661R-A324150030 Page 5 of 12 2023-04-25 Appendix A: Test results DEKRA Testing and Certification No. 26, Huaya 1st Rd., Guishan Dist., Taoyuan City 333411 , Taiwan TEL: +886-3-725-7255 www.dekra-certification.com 2320661R-A324150030 Page 6 of 12 2023-04-25 INDEX 1. TEST CONDITIONS ....................................................................................................................................... 7 1.1 Power supply (V) ....................................................................................................................................... 7 1.2 Temperature (ºC) ................................................…

Text truncated - open the document above for the full version.

Report No.: 22B0267R-RFUSBT2V01-A Page: 1 of 56 Te s t R e p o r t Product Name Bluetooth Module Model No. BT-102 FCC ID YKH319-BT10200 Applicant NUMA Electronics Inc. Address 3F, No. 5, Wugong 5th Rd., Xinzhuang Dist New Taipei City Taiwan Date of Receipt Nov. 07, 2022 Issued Date Feb. 15, 2023 Report No. 22B0267R-RFUSBT2V01-A Report Version V1.0 The test results relate only to the samples tested. The test results shown in the test report are traceable to the national/international standard through the calibration repor t of the e quipment and evaluated measurement uncertainty herein. This report must not be used to claim product endorsement by TAF or any agency of the government. The test report shall not be reproduced without the written approval of DEKRA Testing and Certification Co., Ltd. Measurement uncertainties evaluated for each testing system and associated connections are given here to provide the system information for reference. Compliance determinations do not take into account measurement uncertainties for each testing system, but are based on the results of the compliance measurement. Report No.: 22B0267R-RFUSBT2V01-A Page: 2 of 56 Test Report Product Name Bluetooth Module Applicant NUMA Electronics Inc. Address 3F, No. 5, Wugong 5th Rd., Xinzhuang Dist New Taipei City Taiwan Manufacturer NUMA Electronics Inc. Model No. BT-102 FCC ID YKH319-BT10200 EUT Rated Voltage DC 3.0-3.6 V EUT Test Voltage DC 3.3 V (Power by Test Fixture) Trade Name NUMA Applicable Standard FCC CFR Title 47 Part 15 Subpart C ANSI C63.4: 2014, ANSI C63.10: 2013 Test Result Complied Documented By : ( Senior Project Specialist / Joanne Lin ) Tested By : ( Senior Engineer / Bill Lin ) Approved By : ( Senior Engineer / Alan Chen ) Report No.: 22B0267R-RFUSBT2V01-A Page: 3 of 56 TABLE OF CONTENTS 1. General Information ........................................................................................................................ 6 1.1. EUT Description ......................................................................................................................................... 6 1.2. Tested System Details ................................................................................................................................. 8 1.3. Configuration of Tested System ................................................................................................................. 8 1.4. EUT Exercise Software .............................................................................................................................. 8 1.5. Test Facility ................................................................................................................................................ 9 1.6. List of Test Equipment .............................................................................................................................. 10 1.7. Uncertainty ............................................................................................................................................... 11 2. Conducted Emission ...................................................................................................................... 12 2.1. Test Setup ................................................................................................................................................. 12 2.2. Limits ........................................................................................................................................................ 12 2.3. Test Procedure .......................................................................................................................................... 13 2.4. Test Result of Conducted Emission .......................................................................................................... 13 3. Peak Power Output ........................................................................................................................ 15 3.1. Test Setup ................................................................................................................................................. 15 3.2. Limit ......................................................................................................................................................... 15 3.3. Test Procedure .......................................................................................................................................... 15 3.4. Test Result of Peak Power Output ............................................................................................................ 16 4. Radiated Emission .....................................................................................................................…

Text truncated - open the document above for the full version.