YUYSS4006RCBrushless Dc Tubular Motor and Remote controller

S S S a a a n n n H H H s s s i i i n n n T T T u u u b b b u u u l l l a a a r r r M M M o o o t t t o o o r r r f f f o o o r r r E E E l l l e e e c c c t t t r r r i i i c c c R R R o o o l l l l l l e e e r r r B B B l l l i i i n n n d d d s s s Operation Manual SS4006-R22  Thank you for purchasing this product.  To protect your rights , please contact the distributor for the warranty。  In the warranty card, be sure to fill the date of purchase and distributor's name。 Before Using - 2 - Table of Content Before Use Safety Precautions 3 Accessories 4 Name of Each Part 5 Installation 7 Settings Switch Settings and User Mode 12 Connection Between the Electric Roller Blinds and Remote Control 14 Cancel the Connection 16 Switch Between Forward and Reverse Rotations 17 Set Upper and Lower limits 18 Set Preferred Position 20 Cancel Preferred Position 21 Quick Command Guide 22 Miscellaneous Troubleshooting 23 Appendix 25 Before Using - 3 -  Before using this product , please read the manual carefully.  After reading , please keep this manual properly for future reference.  In this manual, the precautions indicated as Warnings and Cautions.Please observe the following precautions to ensure safety. Warning This indicates " Possible death or serious injury may occur ". Caution This indicates " Possible injury or material damage may occur". Caution To reduce the fire risk of electric shock or product damage:  Do not expose the equipment to rain,moist,water dripping or water splashing environment; and do not place objects fully filled with water next to the equipment.  Do not disassemble this equipment.  Do not use any power supply with a voltage not complying with the rated voltage of the equipment.  If there is any abnormal condition or when it needs repair,please contact your distributor or the original dealer. Caution 1. The appliance is not to be used by children or persons with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction 2. Children being supervised not to play with the appliance. 3. Do not allow children to play with fixed controls. Keep remote controls away from children. 4. Important safety instructions. Follow all instructions, since incorrect installation can lead to severe injury. If you find any errors in this manual,or if you are not clear about the description in this manual,please contact the distributor . Thank you! Safety Precautions ！ ！ ！ ！ Before Using - 4 -  Before installing this product, make sure the package is supplied with a complete set of the following accessories: □ Operation Manual × 1 □ SS4006-R22 Tubular Motor × 1 □ Mounting Bracket（with Screws）× 1 set □ Idler Wheels（with Screws）× 1 set □ Remote control（with Battery） × 1 □ Rack for Remote control × 1  The shape of the AC power plug may be different if you purchased the product in different countries or regions.  Either the equivalent products of the aluminum tubes selected by your local distributor or the aluminum tube specified in the drawing provided by our Company can be used for the roller blinds.  If any part in the package is missing or lost, please contact your local distributor. Accessories Before Using - 5 -  Tubular Motor 1. Driving Wheel:  This is for connecting the Tubular Motor and the aluminum tube for the roller blinds so that the rotation of the motor may drive the aluminum tube for the roller blinds to rotate. 2. Code Button:  The Code button is for setting the communication code between the Remote Control and the tubular motor. 3. Coronal Ring 4. Antenna:  The antenna is for receiving the instructions from the Remote Control. 5. AC Power Cord:  The maximum allowed voltage is 300V. Name of Each Part 1 234 5 Before Using - 6 -  Remote control （Front） （Real） （Battery spec.：12V23A） 6. Up button:  It is for controlling the roller blinds to move upwards. 7. Stop button:  It is for controlling the roller blinds to stop and switch between forward and reverse rotations.(P.13) 8. Down button:  It is for controlling the roller blinds to move downward. 9. Channel indicators:  It indicates the window number to be controlled – from the left to the right: 1, 2, 3, 4, 5; if all indicators are lit, it represents the group control.  The cycle of the indicators is 1→2→3→4→5→all indicator lit (this is skipped in the Setting Mode)→1. 10. Channel Selection button:  It is for selecting the window number to be controlled or for group control. 11. Battery cover:  It is to prevent the battery from falling out. 12. Screw Mounting Holes for the Remote Control Socket. 13. Remote Control Socket Mounting Hole for use with 3M Hook. 6 7 8 9 10 11 Name of Each Part  The seat of remote controller 12 13 Before Using - 7 - 1. Select the aluminum tube for the roller blinds (inner diameter φ40 mm): 2. Measure the correct position at the motor end: 3. Inset the Tubular Motor: Installation  Installation of Electric Roller Blinds: Before Using - 8 - 4. Position the Coronal Pin to the slot: 5. Fasten the tube at the motor end with screws: 6. Measure the mounting position at the idler wheel end: Before Using - 9 - 7. Insert the Idler Wheel assembly: 8. Fasten the tube at the Idler Wheel end with screws: 9. Install the Roller Blinds Fabric:Attach the mounting section of the roller blinds fabric smoothly on the aluminum tube for the roller blinds 10. Install the Bracket: Measure a suitable distance for installing the roller blinds rack to the target position (in the curtain box or on the wall). 11. Install the Electric Roller Blinds: Install the Electric Roller Blinds that have been completely assembled onto the mounting rack. Notice! The positioning slot should be firmly fixed into the mounting rack 12. Install the Power Supply: Insert the plug into the power outlet before performing operation and settings. Before Using - 10 -  Method 1: Mount the socket with screws.  Method 2: Mount the socket with a 3M hook.  I…

Text truncated - open the document above for the full version.

FCC ID: YUYSS4006RC Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only. This test report cannot be reproduced, except in full, without prior written permission of the Company. 除非另有說明，此報告結果僅對測試之樣品負責，同時此樣品僅保留90天。本報告未經本公司書面許可，不可部份複製。 This document is issued by the Company subject to its General Conditions of Service (www.sgs.com/terms_and_conditions.htm ) and Terms and Conditions for Electronic Documents (www.sgs.com/terms_e-document.htm ). Attention is drawn to the limitations of liability, indemnification and jurisdictional issues established therein. Even if printed this electronic document is to be treated as an original within the meaning of UCP 600 article 20b. The authenticity of this document may be verified at www.sgsonsite.com/authentication . Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. SGS Taiwan Ltd. No.134, Wu Kung Road, Wuku Industrial Zone, Taipei County, Taiwan /台北縣五股工業區五工路134號 台灣檢驗科技股份有限公司 t (886-2) 2299-3279 f (886-2) 2298-0488 www.tw.sgs.com Member of SGS Group EXTERNAL PHOTOGRAPHS OF EUT FCC ID: YUYSS4006RC Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only. This test report cannot be reproduced, except in full, without prior written permission of the Company. 除非另有說明，此報告結果僅對測試之樣品負責，同時此樣品僅保留90天。本報告未經本公司書面許可，不可部份複製。 This document is issued by the Company subject to its General Conditions of Service (www.sgs.com/terms_and_conditions.htm ) and Terms and Conditions for Electronic Documents (www.sgs.com/terms_e-document.htm ). Attention is drawn to the limitations of liability, indemnification and jurisdictional issues established therein. Even if printed this electronic document is to be treated as an original within the meaning of UCP 600 article 20b. The authenticity of this document may be verified at www.sgsonsite.com/authentication . Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. SGS Taiwan Ltd. No.134, Wu Kung Road, Wuku Industrial Zone, Taipei County, Taiwan /台北縣五股工業區五工路134號 台灣檢驗科技股份有限公司 t (886-2) 2299-3279 f (886-2) 2298-0488 www.tw.sgs.com Member of SGS Group All of EUT Front View of EUT (TX) Transmitter Receiver FCC ID: YUYSS4006RC Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only. This test report cannot be reproduced, except in full, without prior written permission of the Company. 除非另有說明，此報告結果僅對測試之樣品負責，同時此樣品僅保留90天。本報告未經本公司書面許可，不可部份複製。 This document is issued by the Company subject to its General Conditions of Service (www.sgs.com/terms_and_conditions.htm ) and Terms and Conditions for Electronic Documents (www.sgs.com/terms_e-document.htm ). Attention is drawn to the limitations of liability, indemnification and jurisdictional issues established therein. Even if printed this electronic document is to be treated as an original within the meaning of UCP 600 article 20b. The authenticity of this document may be verified at www.sgsonsite.com/authentication . Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. SGS Taiwan Ltd. No.134, Wu Kung Road, Wuku Industrial Zone, Taipei County, Taiwan /台北縣五股工業區五工路134號 台灣檢驗科技股份有限公司 t (886-2) 2299-3279 f (886-2) 2298-0488 www.tw.sgs.com Member of SGS Group Back View of EUT (TX) Side View of EUT (TX)

FCC ID LABEL FORMAT AND LOCATION Applicant: SAN HSIN PLASTECH CO., LTD. FCC ID: YUYSS4006RC

FCC ID: YUYSS4006RC Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only. This test report cannot be reproduced, except in full, without prior written permission of the Company. 除非另有說明，此報告結果僅對測試之樣品負責，同時此樣品僅保留90天。本報告未經本公司書面許可，不可部份複製。 This document is issued by the Company subject to its General Conditions of Service (www.sgs.com/terms_and_conditions.htm ) and Terms and Conditions for Electronic Documents (www.sgs.com/terms_e-document.htm ). Attention is drawn to the limitations of liability, indemnification and jurisdictional issues established therein. Even if printed this electronic document is to be treated as an original within the meaning of UCP 600 article 20b. The authenticity of this document may be verified at www.sgsonsite.com/authentication . Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. SGS Taiwan Ltd. No.134, Wu Kung Road, Wuku Industrial Zone, Taipei County, Taiwan /台北縣五股工業區五工路134號 台灣檢驗科技股份有限公司 t (886-2) 2299-3279 f (886-2) 2298-0488 www.tw.sgs.com Member of SGS Group INTERNAL PHOTOGRAPHS OF EUT FCC ID: YUYSS4006RC Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only. This test report cannot be reproduced, except in full, without prior written permission of the Company. 除非另有說明，此報告結果僅對測試之樣品負責，同時此樣品僅保留90天。本報告未經本公司書面許可，不可部份複製。 This document is issued by the Company subject to its General Conditions of Service (www.sgs.com/terms_and_conditions.htm ) and Terms and Conditions for Electronic Documents (www.sgs.com/terms_e-document.htm ). Attention is drawn to the limitations of liability, indemnification and jurisdictional issues established therein. Even if printed this electronic document is to be treated as an original within the meaning of UCP 600 article 20b. The authenticity of this document may be verified at www.sgsonsite.com/authentication . Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. SGS Taiwan Ltd. No.134, Wu Kung Road, Wuku Industrial Zone, Taipei County, Taiwan /台北縣五股工業區五工路134號 台灣檢驗科技股份有限公司 t (886-2) 2299-3279 f (886-2) 2298-0488 www.tw.sgs.com Member of SGS Group Open View of EUT (TX) Internal of EUT – 1 (TX) Antenna FCC ID: YUYSS4006RC Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only. This test report cannot be reproduced, except in full, without prior written permission of the Company. 除非另有說明，此報告結果僅對測試之樣品負責，同時此樣品僅保留90天。本報告未經本公司書面許可，不可部份複製。 This document is issued by the Company subject to its General Conditions of Service (www.sgs.com/terms_and_conditions.htm ) and Terms and Conditions for Electronic Documents (www.sgs.com/terms_e-document.htm ). Attention is drawn to the limitations of liability, indemnification and jurisdictional issues established therein. Even if printed this electronic document is to be treated as an original within the meaning of UCP 600 article 20b. The authenticity of this document may be verified at www.sgsonsite.com/authentication . Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. SGS Taiwan Ltd. No.134, Wu Kung Road, Wuku Industrial Zone, Taipei County, Taiwan /台北縣五股工業區五工路134號 台灣檢驗科技股份有限公司 t (886-2) 2299-3279 f (886-2) 2298-0488 www.tw.sgs.com Member of SGS Group Internal of EUT – 2 (TX)

Report No: ER/2010/90002 FCC ID: YUYSS4006RC Issue Date: Oct. 11, 2010 Page: 1 of 24 Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only. This test report cannot be reproduced, except in full, without prior written permission of the Company. 除非另有說明，此報告結果僅對測試之樣品負責，同時此樣品僅保留90天。本報告未經本公司書面許可，不可部份複製。 This document is issued by the Company subject to its General Conditions of Service (www.sgs.com/terms_and_conditions.htm ) and Terms and Conditions for Electronic Documents (www.sgs.com/terms_e-document.htm ). Attention is drawn to the limitations of liability, indemnification and jurisdictional issues established therein. Even if printed this electronic document is to be treated as an original within the meaning of UCP 600 article 20b. The authenticity of this document may be verified at www.sgsonsite.com/authentication . Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. SGS Taiwan Ltd. No.134, Wu Kung Road, Wuku Industrial Zone, Taipei County, Taiwan /台北縣五股工業區五工路134號 台灣檢驗科技股份有限公司 t (886-2) 2299-3279 f (886-2) 2298-0488 www.tw.sgs.com Member of SGS Group ELECTROMAGNETIC EMISSIONS COMPLIANCE REPORT INTENTIONAL RADIATOR CERTIFICATION TO FCC PART 15 SUBPART C REQUIREMENT OF Product Name: Brushless Dc Tubular Motor and Remote controller Brand Name: San Hsin Model Name: SS4006-R22(Receiver); SS4006-RC(Transmitter) Model Different: N/A FCC ID: YUYSS4006RC Report No.: ER/2010/90002 Issue Date: Oct. 11, 2010 Rule Part: §15.231 Prepared by: SAN HSIN PLASTECH CO., LTD. NO. 17 Jian Guo E. RD., Tao Yuan Cit y, Tao Yuan County 330, Taiwan, R.O.C. Prepared by: SGS Taiwan Ltd. Electronics & Communication Laboratory No. 134, Wu Kun g Rd., Wuku Industrial Zone, Taipei County, Taiwan. Note: This report shall not be reproduced except in full, without the written approval of SGS Taiwan Ltd. This document may be altered or revised by SGS Taiwan Ltd. personnel only, and shall be noted in the revision section of the document. Report No: ER/2010/90002 FCC ID: YUYSS4006RC Issue Date: Oct. 11, 2010 Page: 2 of 24 Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only. This test report cannot be reproduced, except in full, without prior written permission of the Company. 除非另有說明，此報告結果僅對測試之樣品負責，同時此樣品僅保留90天。本報告未經本公司書面許可，不可部份複製。 This document is issued by the Company subject to its General Conditions of Service (www.sgs.com/terms_and_conditions.htm ) and Terms and Conditions for Electronic Documents (www.sgs.com/terms_e-document.htm ). Attention is drawn to the limitations of liability, indemnification and jurisdictional issues established therein. Even if printed this electronic document is to be treated as an original within the meaning of UCP 600 article 20b. The authenticity of this document may be verified at www.sgsonsite.com/authentication . Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. SGS Taiwan Ltd. No.134, Wu Kung Road, Wuku Industrial Zone, Taipei County, Taiwan /台北縣五股工業區五工路134號 台灣檢驗科技股份有限公司 t (886-2) 2299-3279 f (886-2) 2298-0488 www.tw.sgs.com Member of SGS Group VERIFICATION OF COMPLIANCE Applicant: SAN HSIN PLASTECH CO., LTD. NO. 17 Jian Guo E. RD., Tao Yuan City, Tao Yuan County 330, Taiwan, R.O.C. Product Name: Brushless Dc Tubular Motor and Remote controller Brand Name: San Hsin FCC ID: YUYSS4006RC Model No.: SS4006-R22(Receiver);SS4006-RC(Transmitter) Model Difference: N/A File Number: ER/2010/90002 Date of test: Sep. 06, 2010 ~ Oct. 08, 2010 Date of EUT Received: Sep. 06, 2010 We hereby certify that: The above equipment was tested by SGS Taiwan Ltd. Electronics & Communication Laboratory The test data, data evaluation, test procedures, and equipment configurations shown in this report were made in accordance with the procedures given in ANSI C63.4 (2003) and the energy emitted by the sample EUT tested as described in this report is in compliance with conducted and radiated emission limits of FCC Rules Part 15.231. The test results of this report relate only to the tested sample identified in this report. Test By: Date: Oct. 11, 2010 Brain Chang / Engineer Prepared By: Date: Oct. 11, 2010 Gigi Yeh / Clerk Approved By: Date: Oct. 11, 2010 Arno Hsieh / Asst. Supervisor Report No: ER/2010/90002 FCC ID: YUYSS4006RC Issue Date: Oct. 11, 2010 Page: 3 of 24 Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only. This test report cannot be reproduced, except in full, without prior written permission of the Company. 除非另有說明，此報告結果僅對測試之樣品負責，同時此樣品僅保留90天。本報告未經本公司書面許可，不可部份複製。 This document is issued by the Company subject to its General Conditions of Service (www.sgs.com/terms_and_conditions.htm ) and Terms and Conditions for Electronic Documents (www.sgs.com/terms_e-document.htm ). Attention is drawn to the limitations of liability, indemnification and jurisdictional issues established therein. Even if printed this electronic document is to be treated as an original within the meaning of UCP 600 article 20b. The authenticity of this document may be verified at www.sgsonsite.com/authentication . Any holder of this document is advised that information contained hereon reflec…

Text truncated - open the document above for the full version.

FCC ID: YUYSS4006RC Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only. This test report cannot be reproduced, except in full, without prior written permission of the Company. 除非另有說明，此報告結果僅對測試之樣品負責，同時此樣品僅保留90天。本報告未經本公司書面許可，不可部份複製。 This document is issued by the Company subject to its General Conditions of Service (www.sgs.com/terms_and_conditions.htm ) and Terms and Conditions for Electronic Documents (www.sgs.com/terms_e-document.htm ). Attention is drawn to the limitations of liability, indemnification and jurisdictional issues established therein. Even if printed this electronic document is to be treated as an original within the meaning of UCP 600 article 20b. The authenticity of this document may be verified at www.sgsonsite.com/authentication . Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. SGS Taiwan Ltd. No.134, Wu Kung Road, Wuku Industrial Zone, Taipei County, Taiwan /台北縣五股工業區五工路134號 台灣檢驗科技股份有限公司 t (886-2) 2299-3279 f (886-2) 2298-0488 www.tw.sgs.com Member of SGS Group PHOTOGRAPHS OF SET UP FCC ID: YUYSS4006RC Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only. This test report cannot be reproduced, except in full, without prior written permission of the Company. 除非另有說明，此報告結果僅對測試之樣品負責，同時此樣品僅保留90天。本報告未經本公司書面許可，不可部份複製。 This document is issued by the Company subject to its General Conditions of Service (www.sgs.com/terms_and_conditions.htm ) and Terms and Conditions for Electronic Documents (www.sgs.com/terms_e-document.htm ). Attention is drawn to the limitations of liability, indemnification and jurisdictional issues established therein. Even if printed this electronic document is to be treated as an original within the meaning of UCP 600 article 20b. The authenticity of this document may be verified at www.sgsonsite.com/authentication . Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. SGS Taiwan Ltd. No.134, Wu Kung Road, Wuku Industrial Zone, Taipei County, Taiwan /台北縣五股工業區五工路134號 台灣檢驗科技股份有限公司 t (886-2) 2299-3279 f (886-2) 2298-0488 www.tw.sgs.com Member of SGS Group Radiated Emission Setup Photos