YZP-REGXXOXXAESL Gateway

* LG Innotek REGX-XOXXA (Electronic Shelf Label Gateway) This is the reference manual for ESL Gateway handling. After fully understanding this manual, use the Gateway in proper way ◆ Read all instructions before performing any work. ◆ Installation must be done completely after fully understanding [Safety Rules] ◆ Installer should give this Instruction to actual user after fully understanding it. ◆ Please, keep this manual in a handy place. When reinstalling or repairing, give this manual to new user or contractor 1. Safety Rules ◆ In case of mishandling, risk sign arises, Meaning of the sign is explained in below table. ◆ In this guide, the safety instruction levels are classified into "WARNING" and "CAUTION". CAUTION - Indicates incorrect handling that may cause hazardous conditions, resulting in slight injury or physical damage. WARNING - Indicates incorrect handling that may cause hazardous conditions, resulting in death or severe injury ! CAUTION Only use rated voltage. (Using lower/higher voltage than rated voltage may cause fire) Do not touch this equipment or cable with wet hands. (It may cause electrocution) Do not install this equipment where using combustible gas leak. (It may cause fire) Do not locate it in high humidity environment. (Condensation or Rust in the equipment cause electrocution or fire) Do not use excessive pressure on equipment to remove. (It may cause damage to ceiling material) When you have minor trouble, please refer to “Trouble Shooting” section first ! W ARNING Shut down your equipment immediately if it produces smoke, a strange odor, or unusual noise. Keep your device away from radiators and heat sources. (It may cause fire) Never disassemble or modify this product. (Improper work may result in injury or fire. Contact selling office for repair.) Be sure to set this equipment on a firm, stable, horizontal ceiling. (The product could be broken or cause injury if it falls) Do not allow foreign body to fall into the equipment. (It may cause fire or electrocution) Installation must be done completely following this instruction to prevent fire or electrocution. Do not Install on the insulating material (It may cause fire) Do not connect both POE cable and DC cable to ESL Gateway (It may cause break down or fire) Request to seller office or professional contractor for installation. Do not cover this equipment with a newspaper, tablecloth, curtain, etc. (it may cause fire) 2. Installation Parts Below parts are needed for installation. Please procure the parts before installation. No. Category Description 1 LAN Cable 10BaseT Cat. 5 or 100BaseTX Cat. 5 STP (Shielded Twisted Pair) RJ-45 2 DC Adaptor (Using DC) DC 12V / 1A or above, 3.5∅ DC Power Jack 3 POE hub (Using POE) More 12Watts Max Port Output 4 Screw driver 3. Contents of pack - REGX-XOXXA (ESL Gateway) 1ea - User’s Manual (this manual) 1ea - Bracket 1ea (Optional) - Screw 2ea (Optional) 4. Installation (Using Spring) ① Before Installation, Check following conditions. - Ceiling should be able to stand weight of ESL Gateway (0.4kg) - Fix reinforcement material to prevent ESL Gateway from moving on the ceiling. ② Secure space to insert ESL Gateway into the ceiling - Make specified space (Diameter ∅100mm+3, -0) - Mounting ceiling thickness : 5mm ~ 20mm ! WARRING - Be sure to set this equipment on a firm, stable, horizontal ceiling. (The product could be broken or cause injury if it falls) ③ Connect (LAN Cable/Power Cable) Wire There are 2 cases for powering ESL Gateway - Case 1 : Using POE (Power Over Ethernet) - Case 2 : Using DC Adapter ! WARRING – Do not Install on the insulating material (It may cause fire) ④ Insert Gateway into the Hole - Pushing 2 springs in direction of arrow paint, put the ESL Gateway into the ceiling. ⑤ How to Remove - Put flathead screwdriver to make hole on the both side. - Push screwdriver in arrow direction to make gap between ceiling and equipment. When gap is wider, Grab spring by hand and put down the equipment. ! WARRING – Do not connect both POE cable and DC cable to ESL Gateway (It may cause break down or fire) 5-1. Using Bracket If you cannot make a hole on the ceiling, use the bracket in the package to install the ESL Gateway. ① Secure the bracket to the ceiling ② Combine the ESL gateway with bracket and bracket socket ! CAUTION – Do not use excessive pressure on equipment to remove. (It may cause damage to ceiling material) Associated side view is as below: 5. Specifications 6. LED Operating LED on the ESL Gateway indicates equipment status. Before operating, check this LED Color. After Booting and all OS loaded, red power LED turn is Normal Status. LED Operating Table LED Explanation Color Scene WLAN Communication with PDA or article matching device Green On Active Off In-active 802.15.4 Communication with ESL Tag (Transmit data) Green Blinking Active Off In-active Ethernet Communication with EMS Green Blinking Active Off In-active Power Gateway status indicating Red On Normal State Off Power Off Blinking (1-sec Interval) Upgrade state or Factory test mode All LED Boot up All On Boot up OS loading All Off OS loading after Boot up If there is any problem, turn off the equipment immediately and contact selling office. 7. Troubleshooting - Hardware Reset In case of malfunctions, reset the gateway by Hardware Reset button. On the top of the equipment there is a reset button. Pressing reset button strongly for 10 seconds 8. Warranty Under normal use condition, products resulting from its own failures in the warranty period will be free maintenance. Warranty Terms as following: a) Charge-free maintenance of the product is one year. We can repair it for free during the guarantee period (Damages not caused by misuse). b) During guarantee period, breakdown caused by misuse or other reasons out of range of warranty. You could ask repair and we charge for changed components and the maintenance. c) When the products need maintenance, contact to the local distributor. d) Taking apart …

Text truncated - open the document above for the full version.

SCS-F18: Project and Product Certification Representative Authorization Letter Page 2 of 2 Rev 5.0 (April 23, 2015) To: SIEMIC, INC. 775 Montague Expressway, Milpitas, CA 95035 USA Dear Sir/Madam, Re: Product Certification Representative Authorization Letter We, LG Innotek Co., Ltd. hereby authorize SIEMIC, Inc. to act as a Certification Body for certifying for the following project(s): (ESL Gateway, REGX-XOXXA) FCC ID: YZP-REGXXOXXA Sincerely, ____________________________ Client’s signature : LG Innotek Co., Ltd. Client’s name / title : Jeong InChang / Director Contact information / address : 978-1, Jangduk-dong, Gwangsan-gu, Gwangju, 506-731 Korea Telephone: +82-62-950-0332 Fax No.: +82-62-950-0368 E-mail: [email protected]

SCS-F19: Confidentiality Request Letter Page 2 of 3 Rev 4.0 (April 23, 2015) To: Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD Subject: Permanent Confidentiality Request for FCC ID: YZP-REGXXOXXA We hereby request confidential treatment of information accompanying this application as outlined below: - e.g. Block Diagram - e.g. Schematics - e.g. Operational Description - e.g. Part List The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. The applicant understands that pursuant to Section 0.457 & 0.459 of the Rules, disclosure of this application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely, ____________________________ Client’s signature : LG Innotek Co., Ltd. Client’s name / title : Jeong InChang / Director Contact information / address : 978-1, Jangduk-dong, Gwangsan-gu, Gwangju, 506-731 Korea Telephone: +82-62-950-0332 Fax No.: +82-62-950-0368 E-mail: [email protected] SCS-F19: Confidentiality Request Letter Page 3 of 3 Rev 4.0 (April 23, 2015) To: Federal Communications Commission Office of Engineering and Technology Equipment Authorization Division 7345 Oakland Mills Road Columbia, Maryland 21046 Subject: Short Term Confidentiality Request for FCC ID: YZP-REGXXOXXA To Whom It May Concern: Pursuant to sections 0.457 and 0.459 of CFR 47 and to avoid premature release of sensitive information prior to marketing or release of the product to the public, the applicant requests the following documents contained in this certification application be temporarily withheld from public disclosure for an initial period of 45 or 180 days (please check one). - User Manual - External Photos - Internal Photos - Test Setup photo The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. Sincerely, ____________________________ Client’s signature : LG Innotek Co., Ltd. Client’s name / title : Jeong InChang / Director Contact information / address : 978-1, Jangduk-dong, Gwangsan-gu, Gwangju, 506-731 Korea Telephone: +82-62-950-0332 Fax No.: +82-62-950-0368 E-mail: [email protected]

Page 1 of 6 Page 2 of 6 Page 3 of 6 Page 4 of 6 Page 5 of 6 Page 6 of 6

Page 1 of 1 IDENTIFICATION LABEL: PROPOSED FCC ID LABEL The FCC ID shall be permanently affixed in the rear side of the equipment This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operations. Made in Korea FCC ID : YZP-REGXXOXXA

Page 1 of 5 Page 2 of 5 Page 3 of 5 Page 4 of 5 Page 5 of 5

Page 1 of 9 Report No. : W154R-D014 It should not be reproduced except in full, without the written approval of ONETECH Corp. EMC-003 (Rev.2) HEAD OFFICE : 301-14 Daessangnyeong-ri, Chowol-eup, Gwangju-si, Gyeonggi-do 464-862 Korea (TEL: 82-31-799-9500, FAX: 82-31-799-9599) EMC Testing Div. : 307-51 Daessangnyeong-ri, Chowol-eup, Gwangju-si, Gyeonggi-do 464-862 Korea (TEL: 82-31-765-8289, FAX: 82-31-766-2904) ELECTROMAGNETIC EMISSION COMPLIANCE REPORT FOR LOW-POWER, NON-LICENSED TRANSMITTER Test Report No. : W154R-D014 AGR No. : A153A-151 Applicant : LG Innotek Co., Ltd. Address : 978-1, Jangduk-dong, Gwangsan-gu, Gwangju, 506-731 Korea Manufacturer : LG Innotek Co., Ltd. Address : 978-1, Jangduk-dong, Gwangsan-gu, Gwangju, 506-731 Korea Type of Equipment : ESL Gateway FCC ID. : YZP-REGXXOXXA Model Name : REGX-XOXXA Serial number : N/A Total page of Report : 9 pages (including this page) Date of Incoming : April 08, 2015 Date of issue : April 22, 2015 SUMMARY The equipment complies with the regulation; FCC PART 15 SUBPART C Section 15.247 This test report only contains the result of a single test of the sample supplied for the examination. It is not a generally valid assessment of the features of the respective products of the mass-production. Reviewed by: Approved by: Ki-Hong, Nam / Asst, Chief Engineer Sung-Ik, Han/ Managing Director ONETECH Corp. ONETECH Corp. Page 2 of 9 Report No. : W154R-D014 It should not be reproduced except in full, without the written approval of ONETECH Corp. EMC-003 (Rev.2) HEAD OFFICE : 301-14 Daessangnyeong-ri, Chowol-eup, Gwangju-si, Gyeonggi-do 464-862 Korea (TEL: 82-31-799-9500, FAX: 82-31-799-9599) EMC Testing Div. : 307-51 Daessangnyeong-ri, Chowol-eup, Gwangju-si, Gyeonggi-do 464-862 Korea (TEL: 82-31-765-8289, FAX: 82-31-766-2904) CONTENTS PAGE 1. VERIFICATION OF COMPLIANCE ............................................................................................................................. 4 2. GENERAL INFORMATION ............................................................................................................................................ 5 2.1 PRODUCT DESCRIPTION ................................................................................................................................................. 5 2.2 ALTERNATIVE TYPE(S)/MODEL(S); ALSO COVERED BY THIS TEST REPORT. ................................................................ 5 3. MAXIMUM PERMISSIBLE EXPOSURE (WLAN MODE) ......................................................................................... 6 3.1 RF EXPOSURE CALCULATION ....................................................................................................................................... 6 3.2 EUT DESCRIPTION ......................................................................................................................................................... 6 3.2 CALCULATED MPE SAFE DISTANCE............................................................................................................................. 7 4. RF EXPOSURE LIMIT (ZIGBEE MODE) ..................................................................................................................... 8 4.1 EUT DESCRIPTION ......................................................................................................................................................... 8 4.2 TEST RESULT ................................................................................................................................................................. 9 Page 3 of 9 Report No. : W154R-D014 It should not be reproduced except in full, without the written approval of ONETECH Corp. EMC-003 (Rev.2) HEAD OFFICE : 301-14 Daessangnyeong-ri, Chowol-eup, Gwangju-si, Gyeonggi-do 464-862 Korea (TEL: 82-31-799-9500, FAX: 82-31-799-9599) EMC Testing Div. : 307-51 Daessangnyeong-ri, Chowol-eup, Gwangju-si, Gyeonggi-do 464-862 Korea (TEL: 82-31-765-8289, FAX: 82-31-766-2904) Revision History Issued Report No. Issued Date Revisions Effect Section W154R-D014 April 22, 2015 Initial Issue All Page 4 of 9 Report No. : W154R-D014 It should not be reproduced except in full, without the written approval of ONETECH Corp. EMC-003 (Rev.2) HEAD OFFICE : 301-14 Daessangnyeong-ri, Chowol-eup, Gwangju-si, Gyeonggi-do 464-862 Korea (TEL: 82-31-799-9500, FAX: 82-31-799-9599) EMC Testing Div. : 307-51 Daessangnyeong-ri, Chowol-eup, Gwangju-si, Gyeonggi-do 464-862 Korea (TEL: 82-31-765-8289, FAX: 82-31-766-2904) 1. VERIFICATION OF COMPLIANCE Applicant : LG Innotek Co., Ltd. Address : 978-1, Jangduk-dong, Gwangsan-gu, Gwangju, 506-731 Korea Contact Person : Inchang, Jeong / Senior engineer Telephone No. : +82-62-950-0332 FCC ID : YZP-REGXXOXXA Model Name : REGX-XOXXA Serial Number : N/A Date : April 22, 2015 EQUIPMENT CLASS DTS – DIGITAL TRNSMISSION SYSTEM E.U.T. DESCRIPTION ESL Gateway THIS REPORT CONCERNS Original Grant MEASUREMENT PROCEDURES ANSI C63.10: 2013 TYPE OF EQUIPMENT TESTED Pre-Production KIND OF EQUIPMENT AUTHORIZATION REQUESTED Certification EQUIPMENT WILL BE OPERATED UNDER FCC RULES PART(S) FCC PART 15 SUBPART C Section 15.247 Modifications on the Equipment to Achieve Compliance None Final Test was Conducted On 3 m, Semi Anechoic Chamber -. The above equipment was tested by ONETECH Corp. for compliance with the requirement set forth in the FCC Rules and Regulations. This said equipment in the configuration described in this report, shows the maximum emission levels emanating from equipment are within the compliance requirements. Page 5 of 9 Report No. : W154R-D014 It should not be reproduced except in full, without the written approval of ONETECH Corp. EMC-003 (Rev.2) HEAD OFFICE : 301-14 Daessangnyeong-ri, Chowol-eup, Gwangju-si, Gyeonggi-do 464-862 Korea (TEL: 82-31-799-9500, FAX: 82-31-799-9599) EMC Testing Div. : 307-51 Daessangnyeong-ri, Chowol-eup, Gwangju-si, Gyeonggi-do 464-862 Korea (TEL: 82-31-765-8289, FAX: 82-31-766-2904) …

Text truncated - open the document above for the full version.

Page 1 of 140 Report No. : W154R-D013 It should not be reproduced except in full, without the written approval of ONETECH Corp. EMC-003 (Rev.2) HEAD OFFICE : 301-14 Daessangnyeong-ri, Chowol-eup, Gwangju-si, Gyeonggi-do 464-862 Korea (TEL: 82-31-799-9500, FAX: 82-31-799-9599) EMC Testing Div. : 307-51 Daessangnyeong-ri, Chowol-eup, Gwangju-si, Gyeonggi-do 464-862 Korea (TEL: 82-31-765-8289, FAX: 82-31-766-2904) ELECTROMAGNETIC EMISSION COMPLIANCE REPORT FOR LOW-POWER, NON-LICENSED TRANSMITTER Test Report No. : W154R-D013 AGR No. : A153A-151 Applicant : LG Innotek Co., Ltd. Address : 978-1, Jangduk-dong, Gwangsan-gu, Gwangju, 506-731 Korea Manufacturer : LG Innotek Co., Ltd. Address : 978-1, Jangduk-dong, Gwangsan-gu, Gwangju, 506-731 Korea Type of Equipment : ESL Gateway FCC ID. : YZP-REGXXOXXA Model Name : REGX-XOXXA Serial number : N/A Total page of Report : 140 pages (including this page) Date of Incoming : April 08, 2015 Date of issue : April 22, 2015 SUMMARY The equipment complies with the regulation; FCC PART 15 SUBPART C Section 15.247 This test report only contains the result of a single test of the sample supplied for the examination. It is not a generally valid assessment of the features of the respective products of the mass-production. Reviewed by: Approved by: Ki-Hong, Nam / Asst, Chief Engineer Sung-Ik, Han/ Managing Director ONETECH Corp. ONETECH Corp. Page 2 of 140 Report No. : W154R-D013 It should not be reproduced except in full, without the written approval of ONETECH Corp. EMC-003 (Rev.2) HEAD OFFICE : 301-14 Daessangnyeong-ri, Chowol-eup, Gwangju-si, Gyeonggi-do 464-862 Korea (TEL: 82-31-799-9500, FAX: 82-31-799-9599) EMC Testing Div. : 307-51 Daessangnyeong-ri, Chowol-eup, Gwangju-si, Gyeonggi-do 464-862 Korea (TEL: 82-31-765-8289, FAX: 82-31-766-2904) CONTENTS PAGE 1. VERIFICATION OF COMPLIANCE ............................................................................................................................. 7 2. TEST SUMMARY .............................................................................................................................................................. 8 2.1 TEST ITEMS AND RESULTS ............................................................................................................................................. 8 2.2 ADDITIONS, DEVIATIONS, EXCLUSIONS FROM STANDARDS ........................................................................................... 8 2.3 RELATED SUBMITTAL(S) / GRANT(S) ............................................................................................................................ 8 2.4 PURPOSE OF THE TEST ................................................................................................................................................... 8 2.5 TEST METHODOLOGY .................................................................................................................................................... 8 2.6 TEST FACILITY ............................................................................................................................................................... 8 3. GENERAL INFORMATION ............................................................................................................................................ 9 3.1 PRODUCT DESCRIPTION ................................................................................................................................................. 9 3.2 ALTERNATIVE TYPE(S)/MODEL(S); ALSO COVERED BY THIS TEST REPORT. .............................................................. 10 4. EUT MODIFICATIONS .................................................................................................................................................. 10 5. SYSTEM TEST CONFIGURATION ............................................................................................................................. 11 5.1 JUSTIFICATION ............................................................................................................................................................. 11 5.2 PERIPHERAL EQUIPMENT ............................................................................................................................................ 11 5.3 MODE OF OPERATION DURING THE TEST .................................................................................................................... 12 5.5 ANTENNA REQUIREMENT ............................................................................................................................................ 13 6. PRELIMINARY TEST .................................................................................................................................................... 14 6.1 TEST FOR WLAN ......................................................................................................................................................... 14 6.1.1 AC Power line Conducted Emissions Tests .......................................................................................................... 14 6.1.2 General Radiated Emissions Tests ....................................................................................................................... 14 6.2 TEST FOR ZIGBEE ......................................................................................................................................................... 14 6.2.1 AC Power line Conducted Emissions Tests .......................................................................................................... 14 6.2.2 General Radiated Emissions Tests ....................................................................................................................... 14 7. TEST DATA OF WLAN .................................................................................................................................................. 15 7.1 MIMIMUM 6 DB BANDWIDTH ......…

Text truncated - open the document above for the full version.

Page 1 of 6 - Conducted Emission Test Adaptor Mode Page 2 of 6 PoE Adaptor Mode Page 3 of 6 - Radiated Emission Test Adaptor Mode Page 4 of 6 Page 5 of 6 PoE Adaptor Mode Page 6 of 6