YZP-TWCMK005DWi-Fi/BT Combo module

User Manual PRODUCT NAME : 802.11a/b/g/n + Bluetooth Combo Module MODEL NAME : TWCM-K005D (00)-0073 The information contained herein is the exclusive property of LG Innotek and shall not be distributed, reproduced or disclosed in whole or no in part without prior written permission of LG Innotek. User Manual PAGE : REG. DATE : 2015.09.14 MODEL NAME :TWCM-K005D REV. DATE : 2015.09.14 REV.NO : 1.0 ©2015 LGIT. All rights reserved. 1/ 9 Table of Contents No.DescriptionPage 1Features2 2Module Photo2 3Block Diagram3 4Storage Conditions4 5Operating Conditions4 6Pin Description5 7Outline Drawing6 8Packing Information7 User Manual PAGE : REG. DATE : 2015.09.14 MODEL NAME :TWCM-K005D REV. DATE : 2015.09.14 REV.NO : 1.0 ©2015 LGIT. All rights reserved. 2/ 9 2. Module Photo 1. Features TWCM-K005D is the module for IEEE 802.11a/b/g/n wireless LAN & Bluetooth4.1. TWCM-K005D is based on MeidaTek MT7632 solution. IEEE 802.11 a/b/g/n Dual Band WLAN infrastructure Bluetooth 4.1 + HS Size : 40mm x46.5mm x 8.25mm 2.4GHz and 5GHz,internal PAand LNA Dual-band 2T2R mode with date rate up to 300Mbps Wake on WLAN and Bluetooth Two Metal Press antenna for WLAN and One External antenna for Bluetooth Host interface : USB 2.0 (WLAN & Bluetooth) Security: WAPI, WEP, WPRA, WPA2, WMM, AES, TKIP, CKP Application: DTV, DVR, HD DVDPlayer, Blue-ray Disk Player, STB User Manual PAGE : REG. DATE : 2015.09.14 MODEL NAME :TWCM-K005D REV. DATE : 2015.09.14 REV.NO : 1.0 ©2015 LGIT. All rights reserved. 3/ 9 3. Block Diagram User Manual PAGE : REG. DATE : 2015.09.14 MODEL NAME :TWCM-K005D REV. DATE : 2015.09.14 REV.NO : 1.0 ©2015 LGIT. All rights reserved. 4/ 9 4. Storage Conditions 5. Operating Conditions ParameterMinTypMaxUnit Ambient Temperature0-60°C Ambient Humidity (40°C)--85% Supply Voltage4.7555.25Vdc ParameterMinMaxUnit Storage Temperature-10+70°C Storage Humidity (40°C)-90% Caution: The specifications in Table 1 define levels at which permanent damage to the device can occur. Function operation is not guaranteed under these conditions. Operating at absolute maximum conditions for extend periods can adversely affect the long-term reliability of the device. . Other conditions 1) Do not use or store modules in the corrosive atmosphere, especially where chloride gas, sulfide gas, acid, alkali, salt or the like are contained. Also, avoid exposure to moisture. 2) Store the modules where the temperature and relative humidity do not exceed 5 to 40°Cand 20 to 60%. 3) Assemble the modules within 6 months. Check the soldering ability in case of 6 months over. < Table 1 > User Manual PAGE : REG. DATE : 2015.09.14 MODEL NAME :TWCM-K005D REV. DATE : 2015.09.14 REV.NO : 1.0 ©2015 LGIT. All rights reserved. 5/ 9 6. Pin Description No.NameI/ODescription 1VDDIVDD 5.0V 2USB_DNI/OUSB Communication signal USB_DN 3USB_DPI/OUSB Communication signal USB_DP 4GND-GND 5WoWLANOWake on Wireless LAN 6GND-GND 7BT_WAKE_HOSTOBluetooth wake-up signal 8ResetIReset controlled by main SOC < Top View > < Bottom View > Note. 1) Recommend a Module install sequence for prevent USB device failure -Supply 5.0V power -Connect to data signal (USB_DP, USB_DN) 2) Connector : Connector A1257WR0-8PS A A 1 8 User Manual PAGE : REG. DATE : 2015.09.14 MODEL NAME :TWCM-K005D REV. DATE : 2015.09.14 REV.NO : 1.0 ©2015 LGIT. All rights reserved. 6/ 9 7. Outline Drawing User Manual PAGE : REG. DATE : 2015.09.14 MODEL NAME :TWCM-K005D REV. DATE : 2015.09.14 REV.NO : 1.0 ©2015 LGIT. All rights reserved. 7/ 9 8. Packing Information 8-1. Tray packing User Manual PAGE : REG. DATE : 2015.09.14 MODEL NAME :TWCM-K005D REV. DATE : 2015.09.14 REV.NO : 1.0 ©2015 LGIT. All rights reserved. 8/ 9 8-2. Box packing User Manual PAGE : REG. DATE : 2015.09.14 MODEL NAME :TWCM-K005D REV. DATE : 2015.09.14 REV.NO : 1.0 ©2015 LGIT. All rights reserved. 9/ 9 8-2. Box packing User Manual PAGE : REG. DATE : 2015.09.14 MODEL NAME :TWCM-K005D REV. DATE : 2015.09.14 REV.NO : 1.0 ©2015 LGIT. All rights reserved. 10/ 9 FCC Information This device complies with part 15 of the FCC Results. Operation is subject to the following two conditions : (1) This device may not cause harmful interface, and (2) This device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for CLASS B digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try correct the interference by one or more of the following measures: 1.1. Reorient or relocate the receiving antenna. 1.2. Increase the separation between the equipment and receiver. 1.3. Connect the equipment into an outlet on a circuit different from that to which receiver is connected. 1.4. Consult the dealer or experienced radio/TV technician for help. WARNING Changes or modifications not expressly approved by the manufacturer could void the user’s authority to operate the equipment. Information for OEM Integrator This device is intended only for OEM integrators under the following conditions: 1) The antenna must be installed such that 20 cm is maintained between the antenna and users, and 2) The transmitter module may not be co-located with any other transmitter or antenna. End product labelling The label for end product must include “Contains FCC ID: YZP-TWCMK005D”. “CAUTION : Exposure to Radio Frequency Radiation. This equipment complies with FCC radiation ex…

Text truncated - open the document above for the full version.

SCS-F18: Project and Product Certification Representative Authorization Letter Page 1 of 2 Rev 5.0 775 Montague Expressway Milpitas, CA 95035 Tel: 408-526-1188 Fax: 408-526-1088 Email: [email protected] Project and Product Certification Representative Authorization Letter Reason for Amendment (current / obsolete) Revision History Approved Date From To Initial Release (obsolete) 1.0 1.0 Nov-14-2006 Revised wording (obsolete) 1.0 2.0 Sept–25-2007 Updated company template (obsolete) 2.0 3.0 Jan-31-2012 Updated letter information (obsolete) 3.0 4.0 May-23-2014 Added FCC ID field (current) 4.0 5.0 Sept 16 2014 SCS-F18: Project and Product Certification Representative Authorization Letter Page 2 of 2 Rev 5.0 (October 27, 2015) To: SIEMIC, INC. 775 Montague Expressway, Milpitas, CA 95035 USA Dear Sir/Madam, Re: Product Certification Representative Authorization Letter We, LG Innotek Co., Ltd. hereby authorize SIEMIC, Inc. to act as a Certification Body for certifying for the following project(s): (Wi-Fi/BT Combo module, TWCM-K005D) FCC ID: YZP-TWCMK005D Sincerely, ____________________________ Client’s signature : LG Innotek Co., Ltd. Client’s name / title : Jeong InChang / Director Contact information / address : 978-1, Jangduk-dong, Gwangsan-gu, Gwangju, 506-731 Korea Telephone: +82-62-950-0332 Fax No.: +82-62-950-0368 E-mail: [email protected]

SCS-F19: Confidentiality Request Letter Page 1 of 3 Rev 4.0 775 Montague Expressway Milpitas, CA 95035 Tel: 408-526-1188 Fax: 408-526-1088 Email: [email protected] Confidentiality Request Letter Reason for Amendment (current / obsolete) Revision History Approved Date From To Initial Release (obsolete) 1.0 1.0 Nov-14-2006 Adding CFR 2.459 (obsolete) 1.0 2.0 August – 11 - 2008 Updated company template & Added text box (obsolete) 2.0 3.0 Jan-31-2012 Added IC confidentiality letter form (current) 3.0 4.0 March-26-2015 SCS-F19: Confidentiality Request Letter Page 2 of 3 Rev 4.0 (October 27, 2015) To: Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD Subject: Permanent Confidentiality Request for FCC ID: YZP-TWCMK005D We hereby request confidential treatment of information accompanying this application as outlined below: - e.g. Block Diagram - e.g. Schematics - e.g. Operational Description - e.g. SW Security Ops Description - e.g. Part List The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. The applicant understands that pursuant to Section 0.457 & 0.459 of the Rules, disclosure of this application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely, ____________________________ Client’s signature : LG Innotek Co., Ltd. Client’s name / title : Jeong InChang / Director Contact information / address : 978-1, Jangduk-dong, Gwangsan-gu, Gwangju, 506-731 Korea Telephone: +82-62-950-0332 Fax No.: +82-62-950-0368 E-mail: [email protected] SCS-F19: Confidentiality Request Letter Page 3 of 3 Rev 4.0 (October 27, 2015) To: Federal Communications Commission Office of Engineering and Technology Equipment Authorization Division 7345 Oakland Mills Road Columbia, Maryland 21046 Subject: Short Term Confidentiality Request for FCC ID: YZP-TWCMK005D To Whom It May Concern: Pursuant to sections 0.457 and 0.459 of CFR 47 and to avoid premature release of sensitive information prior to marketing or release of the product to the public, the applicant requests the following documents contained in this certification application be temporarily withheld from public disclosure for an initial period of 45 or 180 days (please check one). - User Manual - External Photos - Internal Photos - Test Setup photo The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. Sincerely, ____________________________ Client’s signature : LG Innotek Co., Ltd. Client’s name / title : Jeong InChang / Director Contact information / address : 978-1, Jangduk-dong, Gwangsan-gu, Gwangju, 506-731 Korea Telephone: +82-62-950-0332 Fax No.: +82-62-950-0368 E-mail: [email protected]

SCS-F26 Modular Approval Letter Page 1 of 2 Rev 10.0 775 Montague Expressway Milpitas, CA 95035 Tel: 408-526-1188 Fax: 408-526-1088 Email: [email protected] Modular Approval Declaration Letter Reason for Amendment (current / obsolete) Revision History Approved Date From To Initial Release (Obsolete) 1.0 1.0 Dec-04-2006 Added IC Modular Letter (Obsolete) 1.0 2.0 Feb 16 2009 Add LMA and MA option (Obsolete) 2.0 3.0 April 14 2010 Revised per RSS Gen issue 3.0 (Obsolete) 3.0 4.0 Jan 12 2011 Removed Foot(2) (obsolete) 4.0 5.0 July 19 2011 Adding New note per KDB996369 D01 V01R03 (obsolete) 5.0 6.0 August 29 2011 Updated company template & Added text box (obsolete) 6.0 7.0 Jan-31-2012 Updated modular requirement (obsolete) 7.0 8.0 Sept 05 2014 Updated template to meet RSP 100 issue 10 (obsolete) 8.0 9.0 Nov 20 2014 Updated template to meet RSP 100 issue 11 (current) 9.0 10.0 March 19 2015 SCS-F26 Modular Approval Letter Page 2 of 2 Rev 10.0 (Date) October 27, 2015 (Product name) FCC ID : YZP-TWCMK005D , is seeking FCC Authorization as a Single Modular transmitter / Single Limited Modular Approval (Please check one). The EUT meets the requirements for Single Modular approval / Single Limited Modular Approval (please check one) as detailed in FCC public Notice DA00-1407. Compliance to each of the requirements is described below: Questions are: * Please provide a detailed explanation if the answer is “No.” Item Modular requirement Yes No 1 The radio elements must have the radio frequency circuitry shielded. Physical components and tuning capacitor(s) may be located external to the shield, but must be on the module assembly; V 2 The module must have buffered modulation/data inputs to ensure that the device will comply with Part 15 requirements with any type of input signal; V 3 The module must contain power supply regulation on the module; V 4 The module must contain a permanently attached antenna, or contain a unique antenna connector, and be marketed and operated only with specific antenna(s), per Sections 15.203, 15.204(b), 15.204(c), 15.212(a), 2.929(b); V 5 The module must demonstrate compliance in a stand-alone configuration; V 6 The module must be labelled with its permanently affixed FCC ID label, or use an electronic display (See KDB Publication 784748 about labelling requirements); V 7 The module must comply with all specific rules applicable to the transmitter including all the conditions provided in the integration instructions by the grantee; V 8 The module must comply with RF exposure requirements V Note: (1) LMA may be granted when one or more of the requirements in the table above cannot be demonstrated. LMA will also be issued in those instances where applicants can demonstrate that they will retain control over the final installation of the device, such that compliance of the end product is assured. In such cases, an operating condition on the LMA for the module must state that the module is only approved for use when installed in devices produced by a specific manufacturer. When LMA is sought, the application for equipment certification must specifically state how control of the end product into which the module will be installed, and will be maintained, such that full compliance of the end product is always ensured. (2) Please provide Clear and specific instructions describing the conditions, limitations and procedures for third-parties to use and/or integrate the module into a host device. (3) For non-Software Defined Radio transmitter modules where software is used to ensure compliance of the device, technical description of how such control is implemented to ensure prevention of third party modification must be provided (see KDB 594280). Note 1: Compliance of a module in its final configuration is the responsibility of the applicant. A host device will not be considered certified if the instructions regarding antenna configuration provided in the original description, of one or more separately certified modules it contains, were not followed. Example: A separately certified low-power transceiver module using Bluetooth technology which is housed in a desktop computer, laptop or peripheral does not require the overall system to be recertified, if the desktop computer, laptop or peripheral, as a stand-alone unit, complies with all applicable technical standards. ____________________________ Client’s signature : LG Innotek Co., Ltd. Client’s name / title : Jeong InChang / Director Date: October 27, 2015 Attn: Director of Certification Request for Single Modular Approval for FCC ID: YZP-TWCMK005D Please accept our request for Single Modular Approval in accordance with the requirements of 15.212 as described below. 15.212(a)(1) Single modular transmitters must meet the following requirements to obtain a modular transmitter approval. (i) This module does have its own shielding (ii) This module has buffered modulation/data inputs. (iii) This module has integrated with Power Supply regulator. (iv) This module complied with the antenna requirement of section 15.207 and 15.247, because the antenna is PIFA antenna. (v) This module was tested in a standalone-configuration for radiated emissions (vi) The Module will be labeled with its own FCC ID Number. (vii) This module complies with the requirements of part 15.207 and 15.247 for AC power line conducted emissions and part 15.247 for operation in 2 412 MHz ~ 2 462 MHz, 2 422 MHz ~ 2 452 MHz, 5 180 MHz ~ 5 240 MHz, 5 190 MHz ~ 5 230 MHz, 5 745 MHz ~ 5 825 MHz, 5 755 MHz ~ 5 795 MHz frequency band and must only be used with the antenna that were tested in this filing. (Viii) This module complied with any applicable RF exposure requirement. Sincerely Yours, ____________________________ Client’s signature : LG Innotek Co., Ltd. Client’s name / title : Jeong InChang / Director Contact information / address : 978-1, Jangduk-dong, Gwangsan-gu, Gwangju, 506-731 Korea Telephone: +82-62-950-0332 Fax No.: +82-62-950-0368 E-mail: [email protected]

Date: October 26, 2015 To SIEMIC Inc 775 Montague Expressway Milpitas, CA 95035 RE: New Family Listing Declaration Please review the attached exhibits supporting our request for applying New Family Listing to the FCC ID: YZP-TWCMK005D for Company Name: LG Innotek Co., Ltd. Product Description: Wi- Fi/BT Combo module Base model: TWCM-K005D Additional model(s): TWCM-K010D The only difference between the base model TWCM-K005D and the additional model(s) TWCM- K010D is as follows: 1) These models are identical to basic model except for the model name only. Should you have any questions, please contact us. Sincerely, ____________________________ Client’s signature : LG Innotek Co., Ltd. Client’s name / title : Jeong InChang / Director Contact information / address : 978-1, Jangduk-dong, Gwangsan-gu, Gwangju, 506-731 Korea Telephone: +82-62-950-0332 Fax No.: +82-62-950-0368 E-mail: [email protected]

Page 1 of 2 Page 2 of 2

Page 1 of 1 It should not be reproduced except in full, without the written approval of ONETECH Corp. EMC-003 (Rev.3) HEAD OFFICE : 301-14 Daessangnyeong-ri, Chowol-eup, Gwangju-si, Gyeonggi-do 464-862 Korea (TEL: 82-31-799-9500, FAX: 82-31-799-9599) EMC Testing Div : 307-51 Daessangnyeong-ri, Chowol-eup, Gwangju-si, Gyeonggi-do 464-862 Korea (TEL: 82-31-765-8289, FAX: 82-31-766-2904) IDENTIFICATION LABEL: PROPOSED FCC ID LABEL The FCC ID shall be permanently affixed in the rear side of the equipment

Page 1 of 4 Page 2 of 4 Page 3 of 4 Page 4 of 4

Page 1 of 11 Report No. : W15OR-D029 It should not be reproduced except in full, without the written approval of ONETECH Corp. EMC-003 (Rev.2) HEAD OFFICE : 301-14 Daessangnyeong-ri, Chowol-eup, Gwangju-si, Gyeonggi-do 464-862 Korea (TEL: 82-31-799-9500, FAX: 82-31-799-9599) EMC Testing Div. : 307-51 Daessangnyeong-ri, Chowol-eup, Gwangju-si, Gyeonggi-do 464-862 Korea (TEL: 82-31-765-8289, FAX: 82-31-766-2904) ELECTROMAGNETIC EMISSION COMPLIANCE REPORT FOR LOW-POWER, NON-LICENSED TRANSMITTER Test Report No. : W15OR-D029 AGR No. : A159A-200 Applicant : LG Innotek Co., Ltd. Address : 978-1, Jangduk-dong, Gwangsan-gu, Gwangju, 506-731 Korea Manufacturer : LG Innotek Co., Ltd. Address : 978-1, Jangduk-dong, Gwangsan-gu, Gwangju, 506-731 Korea Type of Equipment : Wi-Fi/BT Combo module FCC ID. : YZP-TWCMK005D Model Name : TWCM-K005D Multiple Model Name : TWCM-K010D Serial number : N/A Total page of Report : 11 pages (including this page) Date of Incoming : September 16, 2015 Date of issue : October 23, 2015 SUMMARY The equipment complies with the regulation; FCC PART 15 SUBPART C Section 15.247 This test report only contains the result of a single test of the sample supplied for the examination. It is not a generally valid assessment of the features of the respective products of the mass-production. Reviewed by: Approved by: Ki-Hong, Nam / Asst, Chief Engineer Sung-Ik, Han/ Managing Director ONETECH Corp. ONETECH Corp. Page 2 of 11 Report No. : W15OR-D029 It should not be reproduced except in full, without the written approval of ONETECH Corp. EMC-003 (Rev.2) HEAD OFFICE : 301-14 Daessangnyeong-ri, Chowol-eup, Gwangju-si, Gyeonggi-do 464-862 Korea (TEL: 82-31-799-9500, FAX: 82-31-799-9599) EMC Testing Div. : 307-51 Daessangnyeong-ri, Chowol-eup, Gwangju-si, Gyeonggi-do 464-862 Korea (TEL: 82-31-765-8289, FAX: 82-31-766-2904) CONTENTS PAGE 1. VERIFICATION OF COMPLIANCE ............................................................................................................................. 4 2. GENERAL INFORMATION ............................................................................................................................................ 5 2.1 PRODUCT DESCRIPTION ................................................................................................................................................. 5 2.2 ALTERNATIVE TYPE(S)/MODEL(S); ALSO COVERED BY THIS TEST REPORT. ................................................................ 6 3. EUT MODIFICATIONS .................................................................................................................................................... 6 4. MAXIMUM PERMISSIBLE EXPOSURE ...................................................................................................................... 7 4.1 RF EXPOSURE CALCULATION ....................................................................................................................................... 7 4.2 EUT DESCRIPTION ......................................................................................................................................................... 8 4.3 CALCULATED MPE SAFE DISTANCE........................................................................................................................... 10 4.3.1 Test data for Antenna 0 ........................................................................................................................................ 10 4.3.2 Test data for Antenna 1 ........................................................................................................................................ 10 4.3.3 Test data for Multiple transmit ............................................................................................................................. 11 Page 3 of 11 Report No. : W15OR-D029 It should not be reproduced except in full, without the written approval of ONETECH Corp. EMC-003 (Rev.2) HEAD OFFICE : 301-14 Daessangnyeong-ri, Chowol-eup, Gwangju-si, Gyeonggi-do 464-862 Korea (TEL: 82-31-799-9500, FAX: 82-31-799-9599) EMC Testing Div. : 307-51 Daessangnyeong-ri, Chowol-eup, Gwangju-si, Gyeonggi-do 464-862 Korea (TEL: 82-31-765-8289, FAX: 82-31-766-2904) Revision History Issued Report No. Issued Date Revisions Effect Section W15OR-D029 October 23, 2015 Initial Issue All Page 4 of 11 Report No. : W15OR-D029 It should not be reproduced except in full, without the written approval of ONETECH Corp. EMC-003 (Rev.2) HEAD OFFICE : 301-14 Daessangnyeong-ri, Chowol-eup, Gwangju-si, Gyeonggi-do 464-862 Korea (TEL: 82-31-799-9500, FAX: 82-31-799-9599) EMC Testing Div. : 307-51 Daessangnyeong-ri, Chowol-eup, Gwangju-si, Gyeonggi-do 464-862 Korea (TEL: 82-31-765-8289, FAX: 82-31-766-2904) 1. VERIFICATION OF COMPLIANCE Applicant : LG Innotek Co., Ltd. Address : 978-1, Jangduk-dong, Gwangsan-gu, Gwangju, 506-731 Korea Contact Person : IC Jeong / Senior engineer Telephone No. : +82-62-950-0332 FCC ID : YZP-TWCMK005D Model Name : TWCM-K005D Serial Number : N/A Date : October 23, 2015 EQUIPMENT CLASS DTS – DIGITAL TRNSMISSION SYSTEM E.U.T. DESCRIPTION Modular Transmitter, Wi-Fi/BT Combo module THIS REPORT CONCERNS Original Grant MEASUREMENT PROCEDURES ANSI C63.10: 2013 TYPE OF EQUIPMENT TESTED Pre-Production KIND OF EQUIPMENT AUTHORIZATION REQUESTED Certification EQUIPMENT WILL BE OPERATED UNDER FCC RULES PART(S) FCC PART 15 SUBPART C Section 15.247 Modifications on the Equipment to Achieve Compliance None Final Test was Conducted On 3 m, Semi Anechoic Chamber -. The above equipment was tested by ONETECH Corp. for compliance with the requirement set forth in the FCC Rules and Regulations. This said equipment in the configuration described in this report, shows the maximum emission levels emanating from equipment are within the compliance requirements. Page 5 of 11 Report No. : W15OR-D029 It should not be reproduced except in full, without the written approval of ONETECH Corp. EMC-003 (Rev.2) HEA…

Text truncated - open the document above for the full version.

Page 1 of 135 Report No. : W15OR-D028 It should not be reproduced except in full, without the written approval of ONETECH. EMC-003 (Rev.1) HEAD OFFICE : 301-14 Daessangnyeong-ri, Chowol-eup, Gwangju-si, Gyeonggi-do 464-862 Korea (TEL: 82-31-799-9500, FAX: 82-31-799-9599) EMC Testing Div. : 307-51 Daessangnyeong-ri, Chowol-eup, Gwangju-si, Gyeonggi-do 464-862 Korea (TEL: 82-31-765-8289, FAX: 82-31-766-2904) ELECTROMAGNETIC EMISSION COMPLIANCE REPORT FOR LOW-POWER, NON-LICENSED TRANSMITTER Test Report No. : W15OR-D028 AGR No. : A159A-200 Applicant : LG Innotek Co., Ltd. Address : 978-1, Jangduk-dong, Gwangsan-gu, Gwangju, Korea. 506-731 Manufacturer : LG Innotek Co., Ltd. Address : 978-1, Jangduk-dong, Gwangsan-gu, Gwangju, Korea. 506-731 Type of Equipment : Wi-Fi/BT Combo module FCC ID. : YZP-TWCMK005D Model Name : TWCM-K005D Multiple Model Name : TWCM-K010D Serial number : N/A Total page of Report : 135 pages (including this page) Date of Incoming : September 16, 2015 Date of issue : October 23, 2015 SUMMARY The equipment complies with the regulation; FCC PART 15 SUBPART E Section 15.407 This test report only contains the result of a single test of the sample supplied for the examination. It is not a generally valid assessment of the features of the respective products of the mass-production. Reviewed by: Approved by: Ki-Hong, Nam / Asst, Chief Engineer Sung-Ik, Han/ Managing Director ONETECH Corp. ONETECH Corp. Page 2 of 135 Report No. : W15OR-D028 It should not be reproduced except in full, without the written approval of ONETECH. EMC-003 (Rev.1) HEAD OFFICE : 301-14 Daessangnyeong-ri, Chowol-eup, Gwangju-si, Gyeonggi-do 464-862 Korea (TEL: 82-31-799-9500, FAX: 82-31-799-9599) EMC Testing Div. : 307-51 Daessangnyeong-ri, Chowol-eup, Gwangju-si, Gyeonggi-do 464-862 Korea (TEL: 82-31-765-8289, FAX: 82-31-766-2904) CONTENTS PAGE 1. VERIFICATION OF COMPLIANCE ............................................................................................................................. 6 2. TEST SUMMARY .............................................................................................................................................................. 7 2.1 TEST ITEMS AND RESULTS ............................................................................................................................................. 7 2.2 ADDITIONS, DEVIATIONS, EXCLUSIONS FROM STANDARDS ........................................................................................... 7 2.3 RELATED SUBMITTAL(S) / GRANT(S) ............................................................................................................................ 7 2.4 PURPOSE OF THE TEST ................................................................................................................................................... 7 2.5 TEST METHODOLOGY .................................................................................................................................................... 7 2.6 TEST FACILITY ............................................................................................................................................................... 7 3. GENERAL INFORMATION ............................................................................................................................................ 8 3.1 PRODUCT DESCRIPTION ................................................................................................................................................. 8 3.2 ALTERNATIVE TYPE(S)/MODEL(S); ALSO COVERED BY THIS TEST REPORT. ................................................................ 9 4. EUT MODIFICATIONS .................................................................................................................................................... 9 5. SYSTEM TEST CONFIGURATION ............................................................................................................................. 10 5.1 JUSTIFICATION ............................................................................................................................................................. 10 5.2 PERIPHERAL EQUIPMENT ............................................................................................................................................ 10 5.3 MODE OF OPERATION DURING THE TEST .................................................................................................................... 11 5.4 CONFIGURATION OF TEST SYSTEM ............................................................................................................................. 13 5.5 ANTENNA REQUIREMENT ............................................................................................................................................ 13 6. PRELIMINARY TEST .................................................................................................................................................... 14 6.1 AC POWER LINE CONDUCTED EMISSIONS TESTS ....................................................................................................... 14 6.2 GENERAL RADIATED EMISSIONS TESTS ..................................................................................................................... 14 7. MIMIMUM 26 DB BANDWIDTH ................................................................................................................................. 15 7.1 OPERATING ENVIRONMENT ......................................................................................................................................... 15 7.2 TEST SET-UP ................................................................................................................................................................. 15 7.3 TEST EQUIPMENT USED ................................................................................................................................................ 1…

Text truncated - open the document above for the full version.

Page 1 of 3 - Conducted Emission Test Page 2 of 3 - Radiated Emission Test Page 3 of 3