Z37RS-05Bluetooth Selfie Stick

Instruction Manual Starting up: Slide switch to “ON” position at the bottom of Selfie wand, then the LED indicator will keep lighting up for every 2 seconds. Pairing and connection: 1.Slide switch to “ON”, the blue LED indicator will quickly flash for every 1 second. 2.Turn on Bluetooth in your mobile device, then search to pair/connect with “BSD-RS” 3.After Bluetooth connected with “BSD-RS”, the blue LED indicator will keep lighting up for every 2 seconds. Photos taking Enter the camera mode on your mobile device and press button for 1 second to take photos every time. Shut down: Slide switch to “OFF” position. Electrical: Operating ambient temperatures:-10 to 40°C Relative humidity range:10 to 90% Battery capacity:45mAn Charging voltage:5V DC Charging time:1 hour Standby time:100 hours Autodyne Frequency:500 times or above Support Systems:Android 3.0 IOS 4.0 or above Monopod: Maximum loading capacity:500g Flex heights:235 to 1005mm Main material:stainless steel Flex height:7sections Clamp: Available range for clamping a mobile phone or digital camera: Length:100-165mm Width:55-87mm Notes: This product supports IOS 4.0/Android 3.0 or above. Because Android is open source system, some smartphones or Tablet may not support our products. FCC Statement Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -- Reorient or relocate the receiving antenna. -- Increase the separation between the equipment and receiver. -- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -- Consult the dealer or an experienced radio/TV technician for help This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions (1)this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation

Besstec Electronics (Zhongshan) Co., Ltd. Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 Date: Oct. 29, 2014 Subject; Request for Confidentiality FCC ID: Z37RS-05 To Whom It May Concern, Pursuant to the provisions of Sections 0.457 and 0.459 of Commission's rules (47CFR0.457, 0.459), we are requesting the Commission to withhold the following attachment(s) as confidential document from public disclosure indefinitely. • Schematic Diagram • Block Diagram • Operational Description Above mentioned document contains detailed system and equipment description are considered as proprietary information in operation of the equipment. The public disclosure of above documents might be harmful to our company and would give competitor an unfair advantage in the market. In additional to above mentioned documents, pursuant to Public Notice DA 04-1705 of the Commission' s policy, in order to comply with the marketing regulations in 47 CFT §2.803 and the importation rules in 47 CFR §2.1204, while ensuring that business sensitive information remains confidential until the actual marketing of newly authorized devices. We are requesting the commission to grant shot-term confidentiality request on the following attachment(s) for 180 days after the grant as outlined in Public Notice DA 04-1705. • External Photos • Internal Photos • Test Setup Photos • User Manual It is our understanding that all measurement test reports, FCC ID label format and correspondent during certification review process cannot be granted as confidential documents and those information will be available for public review once the grant of equipment authorization is issued. Sincerely, Signature: Name: Minghua Zhan Title: QC Manager

External photo RS-05 RS-04 RS-03

LABEL ARTWORK AND LOCATION Model: RS-05 FCC ID: Z37RS-05 Besstec Electronics (Zhongshan) Co., Ltd. FCC ID Location

1 Internal photo 2 3

FCC ID TEST REPORT for Bluetooth Selfie Stick Model: RS-05 FCC ID: Z37RS-05 Prepared for: Besstec Electronics (Zhongshan) Co.,Ltd. Yujing Industrial Park, Torch Development Zone, No. 106, Qihao Road, Zhongshan, China Prepared by: Shenzhen TCT Testing Technology Co.,Ltd 1F, Building 1, Yibaolai Industrial Park, Qiaotou Village, Fuyong Town, Baoan District, Shenzhen, Guangdong, China TEL: +86-0755-27673339 FAX: +86-0755-27673332 Report Number：TCT141027E012 Date of Test： Oct. 28-Nov. 04, 2014 Date of Report： Nov. 05, 2014 The results detailed in this test report relate only to the specific sample(s) tested. It is the Application’s responsibility to ensure that all production units are manufactured with equivalent EMC characteristics. This report is not to be reproduced except in full, without written approval from TCT Testing Technology. FCC ID: Z37RS-05 Report Number: TCT141027E012 Page 2 of 49 Table of Contents 1.0 General Details................................................................................................................................................... 3 1.1 Test Lab Details ........................................................................................................................................... 3 1.2 Applicant Details ......................................................................................................................................... 3 1.3 Description of EUT...................................................................................................................................... 4 1.4 Statement ..................................................................................................................................................... 4 1.5 Test Engineer ............................................................................................................................................... 4 2.0 Test equipments and Associated Equipment used during the test................................................................. 5 2.1 Test Equipments........................................................................................................................................... 5 2.2 AE used during the test ................................................................................................................................ 5 3.0 Technical Details................................................................................................................................................ 6 3.1 Summary of test results ............................................................................................................................... 6 3.2 Test Standards .............................................................................................................................................. 6 4.0 EUT Modification.............................................................................................................................................. 6 5.0 Measurement Uncertainty（95% confidence levels, k=2)............................................................................. 6 6.0 Power Line Conducted Emission Test.............................................................................................................. 7 7.0 20dB Bandwidth Measurement...................................................................................................................... 11 8.0 Maximum Peak Output Power....................................................................................................................... 15 9.0 Carrier Frequency Separation........................................................................................................................ 21 10.0 Number of Hopping Channels...................................................................................................................... 25 11.0 Time of Occupancy (Dwell Time)................................................................................................................. 27 12.0 Band edge Measurement...............................................................................................................................31 13.0 Spurious Emission Test.................................................................................................................................. 40 14.0 Antenna Requirement................................................................................................................................... 49 FCC ID: Z37RS-05 Report Number: TCT141027E012 Page 3 of 49 1.0 General Details 1.1 Test Lab Details Name : Shenzhen Tongce Testing Lab Address: 1F, Leinuo Watch Building, Fuyong Town, Baoan Dist, Shenzhen, China Telephone: 13410377511 Fax: -- The test facility is recognized, certified, or accredited by the following organizations: FCC Registration Number: 572331 Shenzhen TCT Testing Technology Co., Ltd., Shenzhen EMC Laboratory: Shenzhen Tongce Testing Lab The 3m Semi-anechoic chamber has been registered and fully described in a report with the (FCC) Federal Communications Commission. The acceptance letter from the FCC is maintained in our files. Registration Number: 572331 Industry Canada (IC) The 3m Semi-anechoic chamber of Shenzhen TCT Testing Technology Co., Ltd. has been registered by Certification and Engineering Bureau of Industry Canada for radio equipment testing Registration Number IC: 10668A-1 1.2 Applicant Details Applicant: Besstec Electronics (Zhongshan) Co.,Ltd. Address: Yujing Industrial Park, Torch Development Zone, No. 106, Qihao Road, Zhongshan, China Telephone: 86-760-88331776 Fax: 86-760-88331706 Manufacturer: Besstec Electronics (Zhongshan) Co.,Ltd. Address: Yujing Industrial Park, Torch Development Zone, No. 106, Qihao Road, Zhongshan, China Telephone: 86-760-88331776 Fax: 86-760-88331706 FCC ID: Z37RS-05 Report Number: TCT141027E012 Page 4 of 49 1.3 Description of EUT Product: Bluetooth Selfie Stick Model No.: …

Text truncated - open the document above for the full version.

Setup photo Radiated Emission Test Conducted Emission Test